| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| |
| `timescale 1 ns / 1 ps |
| |
| module prga_tb; |
| reg clock; |
| reg RSTB; |
| reg CSB; |
| reg power1, power2; |
| reg power3, power4; |
| reg f_tb_rst; |
| |
| wire gpio; |
| wire [37:0] mprj_io; |
| |
| assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz; |
| |
| // External clock is used by default. Make this artificially fast for the |
| // simulation. Normally this would be a slow clock and the digital PLL |
| // would be the fast clock. |
| |
| always #12.5 clock <= (clock === 1'b0); |
| |
| initial begin |
| clock = 0; |
| end |
| |
| initial begin |
| $dumpfile("prga.vcd"); |
| $dumpvars(0, prga_tb); |
| |
| // Repeat cycles of 1000 clock edges as needed to complete testbench |
| repeat (100) begin |
| repeat (1000) @(posedge clock); |
| // $display("+1000 cycles"); |
| end |
| |
| $display("%c[1;31m",27); |
| `ifdef GL |
| $display ("Monitor: Timeout, Test Mega-Project IO Ports (GL) Failed"); |
| `else |
| $display ("Monitor: Timeout, Test Mega-Project IO Ports (RTL) Failed"); |
| `endif |
| $display("%c[0m",27); |
| $finish; |
| end |
| |
| initial begin |
| RSTB = 1'b0; |
| CSB = 1'b1; // Force CSB high |
| f_tb_rst = 1'b1; |
| #2000; |
| RSTB = 1'b1; // Release reset |
| #300000; |
| CSB = 1'b0; // CSB can be released |
| #10000; |
| f_tb_rst = 1'b0; |
| end |
| |
| initial begin // Power-up sequence |
| power1 = 1'b0; |
| power2 = 1'b0; |
| power3 = 1'b0; |
| power4 = 1'b0; |
| #100; |
| power1 = 1'b1; |
| #100; |
| power2 = 1'b1; |
| #100; |
| power3 = 1'b1; |
| #100; |
| power4 = 1'b1; |
| end |
| |
| wire flash_csb; |
| wire flash_clk; |
| wire flash_io0; |
| wire flash_io1; |
| |
| wire VDD3V3; |
| wire VDD1V8; |
| wire VSS; |
| |
| assign VDD3V3 = power1; |
| assign VDD1V8 = power2; |
| assign VSS = 1'b0; |
| |
| caravel uut ( |
| .vddio (VDD3V3), |
| .vddio_2 (VDD3V3), |
| .vssio (VSS), |
| .vssio_2 (VSS), |
| .vdda (VDD3V3), |
| .vssa (VSS), |
| .vccd (VDD1V8), |
| .vssd (VSS), |
| .vdda1 (VDD3V3), |
| .vdda1_2 (VDD3V3), |
| .vdda2 (VDD3V3), |
| .vssa1 (VSS), |
| .vssa1_2 (VSS), |
| .vssa2 (VSS), |
| .vccd1 (VDD1V8), |
| .vccd2 (VDD1V8), |
| .vssd1 (VSS), |
| .vssd2 (VSS), |
| .clock (clock), |
| .gpio (gpio), |
| .mprj_io (mprj_io), |
| .flash_csb(flash_csb), |
| .flash_clk(flash_clk), |
| .flash_io0(flash_io0), |
| .flash_io1(flash_io1), |
| .resetb (RSTB) |
| ); |
| |
| spiflash #( |
| .FILENAME("prga.hex") |
| ) spiflash ( |
| .csb(flash_csb), |
| .clk(flash_clk), |
| .io0(flash_io0), |
| .io1(flash_io1), |
| .io2(), // not used |
| .io3() // not used |
| ); |
| |
| // ----------------------------------------------------------------------- |
| // -- PRGA Testing ------------------------------------------------------- |
| // ----------------------------------------------------------------------- |
| wire w_tb_pass, w_tb_fail, w_tb_prog_done; |
| |
| // Logging |
| wire [31:0] f_tb_verbosity; |
| reg [31:0] f_tb_cycle_cnt; |
| |
| assign f_tb_verbosity = 1; |
| |
| always @(posedge clock) begin |
| if (f_tb_rst) begin |
| f_tb_cycle_cnt <= 0; |
| end else begin |
| f_tb_cycle_cnt <= f_tb_cycle_cnt + 1; |
| |
| if (w_tb_fail) begin |
| $display(); |
| $display("[INFO] ++=========================++"); |
| $display("[INFO] || TEST FAILED ||"); |
| $display("[INFO] ++=========================++"); |
| $display(); |
| $finish; |
| end else if (w_tb_pass) begin |
| $display(); |
| $display("[INFO] ++=========================++"); |
| $display("[INFO] || TEST PASSED ||"); |
| $display("[INFO] ++=========================++"); |
| $display(); |
| $finish; |
| end |
| end |
| end |
| |
| // -- Test --------------------------------------------------------------- |
| // Signals |
| wire w_test_clk; |
| wire w_test_reset; |
| wire w_test_start; |
| wire [3:0] w_test_bcd1; |
| wire [3:0] w_test_bcd0; |
| wire w_test_ready; |
| wire w_test_done_tick; |
| wire [6:0] w_test_bin; |
| |
| // Tester |
| basic i_tester ( |
| .tb_clk(clock) |
| ,.tb_rst(f_tb_rst) |
| ,.tb_pass(w_tb_pass) |
| ,.tb_fail(w_tb_fail) |
| ,.tb_prog_done(w_tb_prog_done) |
| ,.tb_verbosity(f_tb_verbosity) |
| ,.tb_cycle_cnt(f_tb_cycle_cnt) |
| ,.clk(w_test_clk) |
| ,.reset(w_test_reset) |
| ,.start(w_test_start) |
| ,.bcd1(w_test_bcd1) |
| ,.bcd0(w_test_bcd0) |
| ,.ready(w_test_ready) |
| ,.done_tick(w_test_done_tick) |
| ,.bin(w_test_bin) |
| ); |
| |
| // -- Behavioral Model --------------------------------------------------- |
| // Signals |
| wire w_behav_ready; |
| wire w_behav_done_tick; |
| wire [6:0] w_behav_bin; |
| |
| // DUT |
| bcd2bin i_behav ( |
| .clk(w_test_clk) |
| ,.reset(w_test_reset) |
| ,.start(w_test_start) |
| ,.bcd1(w_test_bcd1) |
| ,.bcd0(w_test_bcd0) |
| ,.ready(w_behav_ready) |
| ,.done_tick(w_behav_done_tick) |
| ,.bin(w_behav_bin) |
| ); |
| |
| // -- Bitstream Loading -------------------------------------------------- |
| wire prog_clk, prog_rst, prog_done, prog_we, prog_din, prog_dout, prog_we_o; |
| |
| prga_bitstream_loader i_loader ( |
| .tb_clk(clock) |
| ,.tb_rst(f_tb_rst) |
| ,.tb_cycle_cnt(f_tb_cycle_cnt) |
| ,.tb_prog_done(w_tb_prog_done) |
| ,.prog_clk(prog_clk) |
| ,.prog_rst(prog_rst) |
| ,.prog_done(prog_done) |
| ,.prog_we(prog_we) |
| ,.prog_din(prog_din) |
| ,.prog_dout(prog_dout) |
| ,.prog_we_o(prog_we_o) |
| ); |
| |
| // -- Implemented Circuit ------------------------------------------------ |
| // Signals |
| wire w_impl_ready; |
| wire w_impl_done_tick; |
| wire [6:0] w_impl_bin; |
| |
| // ----------------------------------------------------------------------- |
| // -- Wiring ------------------------------------------------------------- |
| // ----------------------------------------------------------------------- |
| assign w_test_ready = w_impl_ready; |
| assign w_test_done_tick = w_impl_done_tick; |
| assign w_test_bin = w_impl_bin; |
| |
| assign mprj_io[37] = prog_clk; |
| assign mprj_io[36] = w_test_clk; |
| assign mprj_io[35] = prog_din; |
| assign mprj_io[34] = prog_done; |
| assign mprj_io[33] = prog_rst; |
| assign mprj_io[32] = prog_we; |
| assign mprj_io[31] = 1'b0; |
| assign mprj_io[30] = w_test_reset; |
| assign mprj_io[29] = w_test_start; |
| assign mprj_io[28] = w_test_bcd1[0]; |
| assign mprj_io[27] = w_test_bcd1[1]; |
| assign mprj_io[26] = w_test_bcd1[2]; |
| assign mprj_io[25] = w_test_bcd1[3]; |
| assign mprj_io[24] = w_test_bcd0[0]; |
| assign mprj_io[23] = w_test_bcd0[1]; |
| assign mprj_io[22] = w_test_bcd0[2]; |
| assign mprj_io[21] = w_test_bcd0[3]; |
| assign w_impl_ready = mprj_io[20]; |
| assign w_impl_done_tick = mprj_io[19]; |
| assign w_impl_bin[0] = mprj_io[18]; |
| assign w_impl_bin[1] = mprj_io[17]; |
| assign w_impl_bin[2] = mprj_io[16]; |
| assign w_impl_bin[3] = mprj_io[14]; |
| assign w_impl_bin[4] = mprj_io[13]; |
| assign w_impl_bin[5] = mprj_io[12]; |
| assign w_impl_bin[6] = mprj_io[11]; |
| |
| endmodule |
| `default_nettype wire |
