blob: 222fde85cd62f165c39b93e8e05590daf8d915aa [file] [log] [blame]
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
`default_nettype none
/*
*-------------------------------------------------------------
*
* user_proj_example
*
* This is an example of a (trivially simple) user project,
* showing how the user project can connect to the logic
* analyzer, the wishbone bus, and the I/O pads.
*
* This project generates an integer count, which is output
* on the user area GPIO pads (digital output only). The
* wishbone connection allows the project to be controlled
* (start and stop) from the management SoC program.
*
* See the testbenches in directory "mprj_counter" for the
* example programs that drive this user project. The three
* testbenches are "io_ports", "la_test1", and "la_test2".
*
*-------------------------------------------------------------
*/
`define MPRJ_IO_PADS 38
module user_proj_example #(
parameter BITS = 32
)(
`ifdef USE_POWER_PINS
inout vccd1, // User area 1 1.8V supply
inout vssd1, // User area 1 digital ground
`endif
// Wishbone Slave ports (WB MI A)
input wb_clk_i,
input wb_rst_i,
input wbs_stb_i,
input wbs_cyc_i,
input wbs_we_i,
input [3:0] wbs_sel_i,
input [31:0] wbs_dat_i,
input [31:0] wbs_adr_i,
output wbs_ack_o,
output [31:0] wbs_dat_o,
// Logic Analyzer Signals
input [127:0] la_data_in,
output [127:0] la_data_out,
input [127:0] la_oenb,
// IOs
input [`MPRJ_IO_PADS-1:0] io_in,
output [`MPRJ_IO_PADS-1:0] io_out,
output [`MPRJ_IO_PADS-1:0] io_oeb,
// IRQ
output [2:0] irq
);
wire clk;
wire rst;
wire rx_i;
wire [15:0] FPU_hp_result;
wire [15:0] CLKS_PER_BIT;
wire [`MPRJ_IO_PADS-1:0] io_in;
wire [`MPRJ_IO_PADS-1:0] io_out;
wire [`MPRJ_IO_PADS-1:0] io_oeb;
// IO for input mode set 1 and for output mode set 0
assign io_oeb[5] = 1'b1;
assign io_oeb[23:8] = 16'h0000;
assign io_out[23:8] = FPU_hp_result;
// Uart Pin
assign rx_i = (~la_oenb[1]) ? la_data_in[1] : io_in[5];
// IRQ
assign irq = 3'b000; // Unused
// Ouptut at LA bits [31:16]
assign la_data_out[31:0] = 32'h00000000;
assign la_data_out[47:32] = (&la_oenb[47:32]) ? FPU_hp_result : 16'h0000;
assign la_data_out[127:48] = {79{1'b0}};
// Assuming LA probes [65:64] are for controlling the count clk & reset
assign clk = (~la_oenb[64]) ? la_data_in[64] : wb_clk_i;
assign rst = (~la_oenb[65]) ? la_data_in[65] : ~wb_rst_i;
assign CLKS_PER_BIT = (la_oenb[31:16] == 16'h0000) ? la_data_in[31:16] : 16'd348;
// Initiation of TOP Module
FPU_FSM_TOP FPU_Half_Precision_Top (
`ifdef USE_POWER_PINS
.vccd1(vccd1), // User area 1 1.8V supply
.vssd1(vssd1), // User area 1 digital ground
`endif
.clk(clk),
.rst_l(rst),
.r_Rx_Serial(rx_i),
.CLKS_PER_BIT(CLKS_PER_BIT),
.FPU_hp_result(FPU_hp_result)
);
endmodule
`default_nettype wire