| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| |
| `timescale 1 ns / 1 ps |
| |
| `define PER 25 // period |
| |
| |
| module wb_spi_tb (); |
| reg clock ; |
| reg RSTB ; |
| reg CSB ; |
| reg power1, power2; |
| reg power3, power4; |
| |
| wire gpio ; |
| wire [37:0] mprj_io ; |
| wire [ 7:0] mprj_io_0; |
| wire [15:0] checkbits; |
| |
| |
| integer fd ; |
| integer tmp; |
| |
| reg [8*10:0] uart_data_in = "de 1b2"; |
| |
| reg [23:0] dec_baud; |
| reg [ 7:0] dec_data; |
| |
| |
| reg [7:0] tx_data; |
| |
| wire sck_pin; |
| wire mosi_pin; |
| reg miso_pin; |
| |
| task spi_transaction; |
| begin : task_block |
| integer i; |
| miso_pin = 1'b0; |
| for ( i=7 ;i > -1; i=i-1 ) |
| begin : for_block |
| @(posedge sck_pin); |
| miso_pin = tx_data[i]; |
| rx_data = {rx_data[6:0],mosi_pin}; |
| end |
| @(negedge sck_pin); |
| miso_pin = 1'b0; |
| end |
| endtask |
| |
| wire rx ; |
| reg [23:0] baud_clk = 8; // clk_freq is divided by for |
| reg [ 7:0] rx_data = 8'd0 ; |
| |
| // task spi_receive; |
| // begin : rx_block |
| // repeat(8) |
| // begin |
| // @(posedge sck_pin); |
| // rx_data = {rx_data[6:0],mosi_pin}; |
| // end |
| // end |
| // endtask |
| |
| |
| |
| |
| assign checkbits = mprj_io[31:16]; |
| |
| assign mprj_io[3] = 1'b1; |
| assign mosi_pin = mprj_io[12]; |
| assign sck_pin = mprj_io[13]; |
| assign mprj_io[14] = miso_pin; |
| |
| // External clock is used by default. Make this artificially fast for the |
| // simulation. Normally this would be a slow clock and the digital PLL |
| // would be the fast clock. |
| |
| //50MHz |
| always #(`PER/2) clock <= (clock === 1'b0); |
| |
| initial |
| begin |
| clock = 0; |
| end |
| |
| initial |
| begin |
| $dumpfile("wb_spi.vcd"); |
| $dumpvars(0, wb_spi_tb); |
| |
| // Repeat cycles of 1000 clock edges as needed to complete testbench |
| repeat (70) |
| begin |
| repeat (10000) @(posedge clock); |
| // $display("+1000 cycles"); |
| end |
| $display("%c[1;31m",27); |
| `ifdef GL |
| |
| $display ("Monitor: Timeout, Test Mega-Project WB Port (GL) Failed"); |
| `else |
| $display ("Monitor: Timeout, Test Mega-Project WB Port (RTL) Failed"); |
| `endif |
| |
| $display("%c[0m",27); |
| $finish; |
| end |
| |
| assign rx = uut.mprj.io_out[16]; |
| |
| initial |
| begin |
| tx_data = 8'd0; |
| wait(checkbits[15:4] == 12'hAB6); |
| $display("Monitor: MPRJ-Logic WB Started"); |
| while(checkbits[15:4] != 12'hAB7) |
| begin |
| spi_transaction(); |
| tx_data = rx_data; |
| end |
| |
| end |
| |
| |
| initial |
| begin |
| wait(checkbits[15:4] == 12'hAB7 || checkbits[15:4] == 12'hAB8 ); |
| |
| if(checkbits[15:4] == 12'hAB8) |
| begin |
| $display("SPI failed!"); |
| $finish; |
| end |
| else |
| begin |
| `ifdef GL |
| $display("Monitor: Mega-Project WB (GL) Passed"); |
| `else |
| $display("Monitor: Mega-Project WB (RTL) Passed"); |
| `endif |
| $finish; |
| end |
| end |
| |
| initial |
| begin |
| RSTB <= 1'b0; |
| CSB <= 1'b1; // Force CSB high |
| #2000; |
| RSTB <= 1'b1; // Release reset |
| #100000; |
| CSB = 1'b0; // CSB can be released |
| end |
| |
| initial |
| begin // Power-up sequence |
| power1 <= 1'b0; |
| power2 <= 1'b0; |
| #200; |
| power1 <= 1'b1; |
| #200; |
| power2 <= 1'b1; |
| end |
| |
| |
| |
| wire flash_csb; |
| wire flash_clk; |
| wire flash_io0; |
| wire flash_io1; |
| |
| wire VDD3V3 = power1; |
| wire VDD1V8 = power2; |
| wire USER_VDD3V3 = power3; |
| wire USER_VDD1V8 = power4; |
| wire VSS = 1'b0 ; |
| |
| caravel uut ( |
| .vddio (VDD3V3 ), |
| .vddio_2 (VDD3V3 ), |
| .vssio (VSS ), |
| .vssio_2 (VSS ), |
| .vdda (VDD3V3 ), |
| .vssa (VSS ), |
| .vccd (VDD1V8 ), |
| .vssd (VSS ), |
| .vdda1 (VDD3V3 ), |
| .vdda1_2 (VDD3V3 ), |
| .vdda2 (VDD3V3 ), |
| .vssa1 (VSS ), |
| .vssa1_2 (VSS ), |
| .vssa2 (VSS ), |
| .vccd1 (VDD1V8 ), |
| .vccd2 (VDD1V8 ), |
| .vssd1 (VSS ), |
| .vssd2 (VSS ), |
| .clock (clock ), |
| .gpio (gpio ), |
| .mprj_io (mprj_io ), |
| .flash_csb(flash_csb), |
| .flash_clk(flash_clk), |
| .flash_io0(flash_io0), |
| .flash_io1(flash_io1), |
| .resetb (RSTB ) |
| ); |
| |
| spiflash #(.FILENAME("wb_spi.hex")) spiflash ( |
| .csb(flash_csb), |
| .clk(flash_clk), |
| .io0(flash_io0), |
| .io1(flash_io1), |
| .io2( ), // not used |
| .io3( ) // not used |
| ); |
| |
| |
| |
| endmodule |
| |
| `default_nettype wire |