| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * user_proj_example |
| * |
| * This is an example of a (trivially simple) user project, |
| * showing how the user project can connect to the logic |
| * analyzer, the wishbone bus, and the I/O pads. |
| * |
| * This project generates an integer count, which is output |
| * on the user area GPIO pads (digital output only). The |
| * wishbone connection allows the project to be controlled |
| * (start and stop) from the management SoC program. |
| * |
| * See the testbenches in directory "mprj_counter" for the |
| * example programs that drive this user project. The three |
| * testbenches are "io_ports", "la_test1", and "la_test2". |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module user_proj_example #(parameter BITS = 32) ( |
| `ifdef USE_POWER_PINS |
| inout vccd1 , // User area 1 1.8V supply |
| inout vssd1 , // User area 1 digital ground |
| `endif |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i , |
| input wb_rst_i , |
| input wbs_stb_i , |
| input wbs_cyc_i , |
| input wbs_we_i , |
| input [ 3:0] wbs_sel_i , |
| input [ 31:0] wbs_dat_i , |
| input [ 31:0] wbs_adr_i , |
| output wbs_ack_o , |
| output [ 31:0] wbs_dat_o , |
| // Logic Analyzer Signals |
| input [ 127:0] la_data_in , |
| output [ 127:0] la_data_out, |
| input [ 127:0] la_oenb , |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in , |
| output [`MPRJ_IO_PADS-1:0] io_out , |
| output [`MPRJ_IO_PADS-1:0] io_oeb , |
| // IRQ |
| output [ 2:0] irq , |
| // Port A |
| output sram_csb_a , |
| output [ 8:0] sram_addr_a, |
| input [ 31:0] sram_dout_a, |
| // Port B |
| output sram_csb_b , |
| output sram_web_b , |
| output [ 3:0] sram_mask_b, |
| output [ 8:0] sram_addr_b, |
| output [ 31:0] sram_din_b |
| ); |
| /*--------------------------------------*/ |
| /* User project is instantiated here */ |
| /*--------------------------------------*/ |
| |
| localparam WB_WIDTH = 32; // WB ADDRESS/DATA WIDTH |
| localparam SRAM_ADDR_WD = 9 ; |
| localparam SRAM_DATA_WD = 32; |
| localparam UART_ADDR_WD = 2 ; |
| localparam UART_DATA_WD = 32; |
| |
| //--------------------------------------------------------------------- |
| // WB Master Interface |
| //--------------------------------------------------------------------- |
| wire [`MPRJ_IO_PADS-1:0] io_in ; |
| wire [`MPRJ_IO_PADS-1:0] io_out; |
| wire [`MPRJ_IO_PADS-1:0] io_oeb; |
| |
| //--------------------------------------------------------------------- |
| // SRAM |
| //--------------------------------------------------------------------- |
| wire s0_wb_cyc_i; |
| wire s0_wb_stb_i; |
| wire [ SRAM_ADDR_WD-1:0] s0_wb_adr_i; |
| wire s0_wb_we_i ; |
| wire [ SRAM_DATA_WD-1:0] s0_wb_dat_i; |
| wire [SRAM_DATA_WD/8-1:0] s0_wb_sel_i; |
| wire [ SRAM_DATA_WD-1:0] s0_wb_dat_o; |
| wire s0_wb_ack_o; |
| |
| |
| //--------------------------------------------------------------------- |
| // UART |
| //--------------------------------------------------------------------- |
| wire s1_wb_cyc_i; |
| wire s1_wb_stb_i; |
| wire [ 8:0] s1_wb_adr_o; |
| wire s1_wb_we_i ; |
| wire [WB_WIDTH-1:0] s1_wb_dat_i; |
| wire [WB_WIDTH/8-1:0] s1_wb_sel_i; |
| wire [WB_WIDTH-1:0] s1_wb_dat_o; |
| wire s1_wb_ack_o; |
| |
| //--------------------------------------------------------------------- |
| // SPI |
| //--------------------------------------------------------------------- |
| wire s3_wb_cyc_i; |
| wire s3_wb_stb_i; |
| wire [ 8:0] s3_wb_adr_o; |
| wire s3_wb_we_i ; |
| wire [WB_WIDTH-1:0] s3_wb_dat_i; |
| //wire [UART_DATA_WD/8-1:0] s3_wb_sel_i; |
| wire [WB_WIDTH-1:0] s3_wb_dat_o; |
| wire s3_wb_ack_o; |
| |
| |
| logic alarm; |
| logic master_key_ready; |
| logic [31:0] o_LFSR_Data; |
| |
| |
| wb_interconnect interconnect ( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1 ), // User area 1 1.8V supply |
| .vssd1 (vssd1 ), // User area 1 digital ground |
| `endif |
| .clk_i (wb_clk_i ), |
| .rst (wb_rst_i ), |
| |
| // Master 0 Interface |
| .m0_wb_dat_i(wbs_dat_i ), |
| .m0_wb_adr_i(wbs_adr_i ), |
| .m0_wb_sel_i(wbs_sel_i ), |
| .m0_wb_we_i (wbs_we_i ), |
| .m0_wb_cyc_i(wbs_cyc_i ), |
| .m0_wb_stb_i(wbs_stb_i ), |
| .m0_wb_dat_o(wbs_dat_o ), |
| .m0_wb_ack_o(wbs_ack_o ), |
| |
| // Slave 0 Interface |
| .s0_wb_dat_i(s0_wb_dat_i), |
| .s0_wb_ack_i(s0_wb_ack_o), |
| .s0_wb_dat_o(s0_wb_dat_i), |
| .s0_wb_adr_o(s0_wb_adr_i), |
| .s0_wb_sel_o(s0_wb_sel_i), |
| .s0_wb_we_o (s0_wb_we_i ), |
| .s0_wb_cyc_o(s0_wb_cyc_i), |
| .s0_wb_stb_o(s0_wb_stb_i), |
| |
| // Slave 1 Interface |
| .s1_wb_dat_i(s1_wb_dat_o), |
| .s1_wb_ack_i(s1_wb_ack_o), |
| .s1_wb_dat_o(s1_wb_dat_i), |
| .s1_wb_adr_o(s1_wb_adr_o), |
| .s1_wb_sel_o(s1_wb_sel_i), |
| .s1_wb_we_o (s1_wb_we_i ), |
| .s1_wb_cyc_o(s1_wb_cyc_i), |
| .s1_wb_stb_o(s1_wb_stb_i), |
| |
| // Slave 2 Interface |
| // .s2_wb_dat_i(), |
| // .s2_wb_ack_i(), |
| // .s2_wb_dat_o(), |
| // .s2_wb_adr_o(), |
| // .s2_wb_sel_o(), |
| // .s2_wb_we_o (), |
| // .s2_wb_cyc_o(), |
| // .s2_wb_stb_o(), |
| |
| // Slave 3 Interface |
| .s3_wb_dat_i(s3_wb_dat_o), |
| .s3_wb_ack_i(s3_wb_ack_o), |
| .s3_wb_dat_o(s3_wb_dat_i), |
| .s3_wb_adr_o(s3_wb_adr_o), |
| .s3_wb_sel_o(), |
| .s3_wb_we_o (s3_wb_we_i ), |
| .s3_wb_cyc_o(s3_wb_cyc_i), |
| .s3_wb_stb_o(s3_wb_stb_i) |
| ); |
| |
| |
| sram_wb_wrapper #( |
| `ifndef SYNTHESIS |
| .SRAM_ADDR_WD(SRAM_ADDR_WD), |
| .SRAM_DATA_WD(SRAM_DATA_WD) |
| `endif |
| ) wb_wrapper0 ( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1 ), // User area 1 1.8V supply |
| .vssd1 (vssd1 ), // User area 1 digital ground |
| `endif |
| .rst (wb_rst_i ), |
| // Wishbone Interface |
| .wb_clk_i (wb_clk_i ), // System clock |
| .wb_cyc_i (s0_wb_cyc_i), // cycle enable |
| .wb_stb_i (s0_wb_stb_i), // strobe |
| .wb_adr_i (s0_wb_adr_i), // address |
| .wb_we_i (s0_wb_we_i ), // write |
| .wb_dat_i (s0_wb_dat_i), // data output |
| .wb_sel_i (s0_wb_sel_i), // byte enable |
| .wb_dat_o (s0_wb_dat_o), // data input |
| .wb_ack_o (s0_wb_ack_o), // acknowlegement |
| // SRAM Interface |
| // Port A |
| .sram_csb_a (sram_csb_a ), |
| .sram_addr_a(sram_addr_a), |
| .sram_dout_a (sram_dout_a), |
| // Port B |
| .sram_csb_b (sram_csb_b ), |
| .sram_web_b (sram_web_b ), |
| .sram_mask_b(sram_mask_b), |
| .sram_addr_b(sram_addr_b), |
| .sram_din_b (sram_din_b ), |
| .trng_i(1'b0), |
| .alarm(alarm), |
| .master_key_ready(master_key_ready) |
| ); |
| |
| assign io_oeb = {(`MPRJ_IO_PADS){1'b0}}; |
| |
| |
| |
| simpleuartA_wb |
| simpleuartA_wb_dut ( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1 ), // User area 1 1.8V supply |
| .vssd1 (vssd1 ), // User area 1 digital ground |
| `endif |
| .wb_clk_i (wb_clk_i ), |
| .wb_rst_i (wb_rst_i ), |
| .wb_adr_i (s1_wb_adr_o[1:0]), |
| .wb_dat_i (s1_wb_dat_i ), |
| .wb_sel_i (s1_wb_sel_i ), |
| .wb_we_i (s1_wb_we_i ), |
| .wb_cyc_i (s1_wb_cyc_i ), |
| .wb_stb_i (s1_wb_stb_i ), |
| .wb_ack_o (s1_wb_ack_o ), |
| .wb_dat_o (s1_wb_dat_o ), |
| .uart_enabled ( ), |
| .ser_tx (io_out[16] ), |
| .ser_rx (io_in[15]) |
| ); |
| |
| |
| assign io_out[11] = o_LFSR_Data[0]; |
| |
| LFSR |
| #( |
| .NUM_BITS ( |
| NUM_BITS ) |
| ) |
| LFSR_dut ( |
| .i_Clk (wb_clk_i ), |
| .i_Enable (~wb_rst_i ), |
| .i_Seed_DV (wb_rst_i ), |
| .i_Seed_Data (trng_i ), |
| .o_LFSR_Data (o_LFSR_Data ), |
| .o_LFSR_Done (), |
| .i_LFSR ( io_in[11]), |
| .master_key_ready(master_key_ready), |
| .i_rst(wb_rst_i), |
| .o_alarm(alarm) |
| ); |
| |
| |
| |
| |
| tiny_spi #( |
| .BAUD_WIDTH(0), |
| .BAUD_DIV (8), |
| .SPI_MODE (0), |
| .BC_WIDTH (3), |
| .DIV_WIDTH (2), |
| .IDLE (0) |
| ) tiny_spi_inst ( |
| `ifdef USE_POWER_PINS |
| .vccd1(vccd1 ), // User area 1 1.8V supply |
| .vssd1(vssd1 ), // User area 1 digital ground |
| `endif |
| .rst_i(wb_rst_i ), |
| .clk_i(wb_clk_i ), |
| .stb_i(s3_wb_stb_i ), |
| .we_i (s3_wb_we_i ), |
| .dat_o(s3_wb_dat_o ), |
| .dat_i(s3_wb_dat_i ), |
| .int_o( ), |
| .adr_i(s3_wb_adr_o[2:0]), |
| .cyc_i(s3_wb_cyc_i ), |
| .ack_o(s3_wb_ack_o ), |
| .MOSI (io_out[12] ), |
| .SCLK (io_out[13] ), |
| .MISO (io_in[14] ) |
| ); |
| |
| |
| endmodule |
| `default_nettype wire |
