| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * user_project_wrapper |
| * |
| * This wrapper enumerates all of the pins available to the |
| * user for the user project. |
| * |
| * An example user project is provided in this wrapper. The |
| * example should be removed and replaced with the actual |
| * user project. |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module user_project_wrapper #( |
| parameter BITS = 32 |
| ) ( |
| `ifdef USE_POWER_PINS |
| inout vdda1, // User area 1 3.3V supply |
| inout vdda2, // User area 2 3.3V supply |
| inout vssa1, // User area 1 analog ground |
| inout vssa2, // User area 2 analog ground |
| inout vccd1, // User area 1 1.8V supply |
| inout vccd2, // User area 2 1.8v supply |
| inout vssd1, // User area 1 digital ground |
| inout vssd2, // User area 2 digital ground |
| `endif |
| |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i, |
| input wb_rst_i, |
| input wbs_stb_i, |
| input wbs_cyc_i, |
| input wbs_we_i, |
| input [3:0] wbs_sel_i, |
| input [31:0] wbs_dat_i, |
| input [31:0] wbs_adr_i, |
| output wbs_ack_o, |
| output [31:0] wbs_dat_o, |
| |
| // Logic Analyzer Signals |
| input [127:0] la_data_in, |
| output [127:0] la_data_out, |
| input [127:0] la_oenb, |
| |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in, |
| output [`MPRJ_IO_PADS-1:0] io_out, |
| output [`MPRJ_IO_PADS-1:0] io_oeb, |
| |
| // Analog (direct connection to GPIO pad---use with caution) |
| // Note that analog I/O is not available on the 7 lowest-numbered |
| // GPIO pads, and so the analog_io indexing is offset from the |
| // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io). |
| inout [`MPRJ_IO_PADS-10:0] analog_io, |
| |
| // Independent clock (on independent integer divider) |
| input user_clock2, |
| |
| // User maskable interrupt signals |
| output [2:0] user_irq |
| ); |
| |
| /*--------------------------------------*/ |
| /* User project is instantiated here */ |
| /*--------------------------------------*/ |
| |
| parameter WB_WIDTH = 32; // WB ADDRESS/DATA WIDTH |
| parameter SRAM_ADDR_WD = 8; |
| parameter SRAM_DATA_WD = 32; |
| |
| //--------------------------------------------------------------------- |
| // WB Master Interface |
| //--------------------------------------------------------------------- |
| wire rst_n = not(wb_rst_i); |
| wire [`MPRJ_IO_PADS-1:0] io_in; |
| wire [`MPRJ_IO_PADS-1:0] io_out; |
| wire [`MPRJ_IO_PADS-1:0] io_oeb; |
| |
| //--------------------------------------------------------------------- |
| // SRAM |
| //--------------------------------------------------------------------- |
| wire s0_wb_cyc_i; |
| wire s0_wb_stb_i; |
| wire [SRAM_ADDR_WD-1:0] s0_wb_adr_i; |
| wire s0_wb_we_i; |
| wire [SRAM_DATA_WD-1:0] s0_wb_dat_i; |
| wire [SRAM_DATA_WD/8-1:0] s0_wb_sel_i; |
| wire [SRAM_DATA_WD-1:0] s0_wb_dat_o; |
| wire s0_wb_ack_o; |
| |
| // Port A |
| wire sram_clk_a; |
| wire sram_csb_a; |
| wire [SRAM_ADDR_WD-1:0] sram_addr_a; |
| wire [SRAM_DATA_WD-1:0] sram_dout_a; |
| |
| // Port B |
| wire sram_clk_b; |
| wire sram_csb_b; |
| wire sram_web_b; |
| wire [SRAM_DATA_WD/8-1:0] sram_mask_b; |
| wire [SRAM_ADDR_WD-1:0] sram_addr_b; |
| wire [SRAM_DATA_WD-1:0] sram_din_b; |
| |
| wb_interconnect interconnect |
| ( |
| `ifdef USE_POWER_PINS |
| .vccd1(vccd1), // User area 1 1.8V supply |
| .vssd1(vssd1), // User area 1 digital ground |
| `endif |
| .clk_i(wb_clk_i), |
| .rst_n(rst_n), |
| |
| // Master 0 Interface |
| .m0_wb_dat_i(wbs_dat_i), |
| .m0_wb_adr_i(wbs_adr_i), |
| .m0_wb_sel_i(wbs_sel_i), |
| .m0_wb_we_i (wbs_we_i), |
| .m0_wb_cyc_i(wbs_cyc_i), |
| .m0_wb_stb_i(wbs_stb_i), |
| .m0_wb_dat_o(wbs_dat_o), |
| .m0_wb_ack_o(wbs_ack_o), |
| |
| // Slave 0 Interface |
| .s0_wb_dat_i(sram_dout_a), |
| .s0_wb_ack_i(s0_wb_ack_o), |
| .s0_wb_dat_o(s0_wb_dat_i), |
| .s0_wb_adr_o(s0_wb_adr_i), |
| .s0_wb_sel_o(s0_wb_sel_i), |
| .s0_wb_we_o (s0_wb_we_i), |
| .s0_wb_cyc_o(s0_wb_cyc_i), |
| .s0_wb_stb_o(s0_wb_stb_i) |
| |
| // Slave 1 Interface |
| // .s1_wb_dat_i(), |
| // .s1_wb_ack_i(), |
| // .s1_wb_dat_o(), |
| // .s1_wb_adr_o(), |
| // .s1_wb_sel_o(), |
| // .s1_wb_we_o (), |
| // .s1_wb_cyc_o(), |
| // .s1_wb_stb_o(), |
| |
| // Slave 2 Interface |
| // .s2_wb_dat_i(), |
| // .s2_wb_ack_i(), |
| // .s2_wb_dat_o(), |
| // .s2_wb_adr_o(), |
| // .s2_wb_sel_o(), |
| // .s2_wb_we_o (), |
| // .s2_wb_cyc_o(), |
| // .s2_wb_stb_o(), |
| |
| // Slave 3 Interface |
| // .s3_wb_dat_i(), |
| // .s3_wb_ack_i(), |
| // .s3_wb_dat_o(), |
| // .s3_wb_adr_o(), |
| // .s3_wb_sel_o(), |
| // .s3_wb_we_o (), |
| // .s3_wb_cyc_o(), |
| // .s3_wb_stb_o() |
| ); |
| |
| sram_wb_wrapper #( |
| `ifndef SYNTHESIS |
| .SRAM_ADDR_WD (SRAM_ADDR_WD), |
| .SRAM_DATA_WD (SRAM_DATA_WD) |
| `endif |
| ) |
| wb_wrapper0 ( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), // User area 1 1.8V supply |
| .vssd1 (vssd1), // User area 1 digital ground |
| `endif |
| .rst_n(rst_n), |
| // Wishbone Interface |
| .wb_clk_i(wb_clk_i), // System clock |
| .wb_cyc_i(s0_wb_cyc_i), // cycle enable |
| .wb_stb_i(s0_wb_stb_i), // strobe |
| .wb_adr_i(s0_wb_adr_i), // address |
| .wb_we_i (s0_wb_we_i), // write |
| .wb_dat_i(s0_wb_dat_i), // data output |
| .wb_sel_i(s0_wb_sel_i), // byte enable |
| // .wb_dat_o(s0_wb_dat_o), // data input |
| .wb_ack_o(s0_wb_ack_o), // acknowlegement |
| // SRAM Interface |
| // Port A |
| .sram_csb_a(sram_csb_a), |
| .sram_addr_a(sram_addr_a), |
| |
| // Port B |
| .sram_csb_b(sram_csb_b), |
| .sram_web_b(sram_web_b), |
| .sram_mask_b(sram_mask_b), |
| .sram_addr_b(sram_addr_b), |
| .sram_din_b(sram_din_b) |
| ); |
| |
| sky130_sram_1kbyte_1rw1r_32x256_8 u_sram1_1kb( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), // User area 1 1.8V supply |
| .vssd1 (vssd1), // User area 1 digital ground |
| `endif |
| // Port 0: RW |
| .clk0 (wb_clk_i), |
| .csb0 (sram_csb_b), |
| .web0 (sram_web_b), |
| .wmask0 (sram_mask_b), |
| .addr0 (sram_addr_b), |
| .din0 (sram_din_b), |
| .dout0 (), // dont read from Port B |
| // Port 1: R |
| .clk1 (wb_clk_i), |
| .csb1 (sram_csb_a), |
| .addr1 (sram_addr_a), |
| .dout1 (sram_dout_a) |
| ); |
| |
| endmodule // user_project_wrapper |
| |
| `default_nettype wire |
