| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * user_project_wrapper |
| * |
| * This wrapper enumerates all of the pins available to the |
| * user for the user project. |
| * |
| * An example user project is provided in this wrapper. The |
| * example should be removed and replaced with the actual |
| * user project. |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module user_project_wrapper #( |
| parameter BITS = 32 |
| ) ( |
| `ifdef USE_POWER_PINS |
| inout vdda1, // User area 1 3.3V supply |
| inout vdda2, // User area 2 3.3V supply |
| inout vssa1, // User area 1 analog ground |
| inout vssa2, // User area 2 analog ground |
| inout vccd1, // User area 1 1.8V supply |
| inout vccd2, // User area 2 1.8v supply |
| inout vssd1, // User area 1 digital ground |
| inout vssd2, // User area 2 digital ground |
| `endif |
| |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i, |
| input wb_rst_i, |
| input wbs_stb_i, |
| input wbs_cyc_i, |
| input wbs_we_i, |
| input [3:0] wbs_sel_i, |
| input [31:0] wbs_dat_i, |
| input [31:0] wbs_adr_i, |
| output wbs_ack_o, |
| output [31:0] wbs_dat_o, |
| |
| // Logic Analyzer Signals |
| input [127:0] la_data_in, |
| output [127:0] la_data_out, |
| input [127:0] la_oenb, |
| |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in, |
| output [`MPRJ_IO_PADS-1:0] io_out, |
| output [`MPRJ_IO_PADS-1:0] io_oeb, |
| |
| // Analog (direct connection to GPIO pad---use with caution) |
| // Note that analog I/O is not available on the 7 lowest-numbered |
| // GPIO pads, and so the analog_io indexing is offset from the |
| // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io). |
| inout [`MPRJ_IO_PADS-10:0] analog_io, |
| |
| // Independent clock (on independent integer divider) |
| input user_clock2, |
| |
| // User maskable interrupt signals |
| output [2:0] user_irq |
| ); |
| |
| /*--------------------------------------*/ |
| /* User project is instantiated here */ |
| /*--------------------------------------*/ |
| wire vb_clk0 ; |
| wire vb_csb0 ; |
| wire vb_web0 ; |
| wire [3:0] vb_wmask0 ; |
| wire [12:0] vb_addr0 ; |
| wire [31:0] vb_din0 ; |
| wire [31:0] vb_dout0 ; |
| wire vb_clk1 ; |
| wire vb_csb1 ; |
| wire [12:0] vb_addr1 ; |
| wire [31:0] vb_dout1 ; |
| wire bb_clk0 ; |
| wire bb_csb0 ; |
| wire bb_web0 ; |
| wire [3:0] bb_wmask0 ; |
| wire [`BB_ADRES_BIT-1:0] bb_addr0 ; |
| wire [31:0] bb_din0 ; |
| wire [31:0] bb_dout0 ; |
| wire bb_clk1 ; |
| wire bb_csb1 ; |
| wire [`BB_ADRES_BIT-1:0] bb_addr1 ; |
| wire [31:0] bb_dout1 ; |
| |
| c0_system mprj ( |
| `ifdef USE_POWER_PINS |
| .vccd1(vccd1), // User area 1 1.8V power |
| .vssd1(vssd1), // User area 1 digital ground |
| `endif |
| |
| .clk_g(wb_clk_i), |
| .rst_g(wb_rst_i), |
| |
| // IO Pads |
| .tx(io_out[1]), |
| .rx(io_in[0]), |
| .io_gecerli(io_out[2]), |
| .io_ps(io_out[34:3]), |
| .io_oeb(io_oeb), |
| |
| |
| .bb_csb0 (bb_csb0) , |
| .bb_web0 (bb_web0) , |
| .bb_wmask0 (bb_wmask0) , |
| .bb_addr0 (bb_addr0) , |
| .bb_din0 (bb_din0) , |
| .bb_dout0 (bb_dout0) , |
| |
| .bb_csb1 (bb_csb1) , |
| .bb_addr1 (bb_addr1) , |
| .bb_dout1 (bb_dout1) , |
| |
| .vb_csb0 (vb_csb0) , |
| .vb_web0 (vb_web0) , |
| .vb_wmask0 (vb_wmask0) , |
| .vb_addr0 (vb_addr0) , |
| .vb_din0 (vb_din0) , |
| .vb_dout0 (vb_dout0) , |
| |
| .vb_csb1 (vb_csb1) , |
| .vb_addr1 (vb_addr1) , |
| .vb_dout1 (vb_dout1) |
| ); |
| |
| sky130_sram_2kbyte_1rw1r_32x512_8 VB_SRAM |
| ( |
| `ifdef USE_POWER_PINS |
| .vccd1(vccd1), |
| .vssd1(vssd1), |
| `endif |
| |
| .clk0 (wb_clk_i) , |
| .csb0 (vb_csb0) , |
| .web0 (vb_web0) , |
| .wmask0 (vb_wmask0) , |
| .addr0 (vb_addr0) , |
| .din0 (vb_din0) , |
| .dout0 (vb_dout0) , |
| .clk1 (wb_clk_i) , |
| .csb1 (vb_csb1) , |
| .addr1 (vb_addr1) , |
| .dout1 (vb_dout1) |
| ); |
| |
| sky130_sram_2kbyte_1rw1r_32x512_8 BB_SRAM |
| ( |
| `ifdef USE_POWER_PINS |
| .vccd1(vccd1), |
| .vssd1(vssd1), |
| `endif |
| |
| .clk0 (wb_clk_i) , |
| .csb0 (bb_csb0) , |
| .web0 (bb_web0) , |
| .wmask0 (bb_wmask0) , |
| .addr0 (bb_addr0) , |
| .din0 (bb_din0) , |
| .dout0 (bb_dout0) , |
| .clk1 (wb_clk_i) , |
| .csb1 (bb_csb1) , |
| .addr1 (bb_addr1) , |
| .dout1 (bb_dout1) |
| ); |
| endmodule // user_project_wrapper |
| |
| `default_nettype wire |