| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * user_project_wrapper |
| * |
| * This wrapper enumerates all of the pins available to the |
| * user for the user project. |
| * |
| * An example user project is provided in this wrapper. The |
| * example should be removed and replaced with the actual |
| * user project. |
| * |
| * THIS FILE HAS BEEN GENERATED USING multi_tools_project CODEGEN |
| * IF YOU NEED TO MAKE EDITS TO IT, EDIT codegen/caravel_iface_header.txt |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module user_project_wrapper #( |
| parameter BITS = 32 |
| )( |
| `ifdef USE_POWER_PINS |
| inout vdda1, // User area 1 3.3V supply |
| inout vdda2, // User area 2 3.3V supply |
| inout vssa1, // User area 1 analog ground |
| inout vssa2, // User area 2 analog ground |
| inout vccd1, // User area 1 1.8V supply |
| inout vccd2, // User area 2 1.8v supply |
| inout vssd1, // User area 1 digital ground |
| inout vssd2, // User area 2 digital ground |
| `endif |
| |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i, |
| input wb_rst_i, |
| input wbs_stb_i, |
| input wbs_cyc_i, |
| input wbs_we_i, |
| input [3:0] wbs_sel_i, |
| input [31:0] wbs_dat_i, |
| input [31:0] wbs_adr_i, |
| output wbs_ack_o, |
| output [31:0] wbs_dat_o, |
| |
| // Logic Analyzer Signals |
| input [127:0] la_data_in, |
| output [127:0] la_data_out, |
| input [127:0] la_oenb, |
| |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in, |
| output [`MPRJ_IO_PADS-1:0] io_out, |
| output [`MPRJ_IO_PADS-1:0] io_oeb, |
| |
| // Analog (direct connection to GPIO pad---use with caution) |
| // Note that analog I/O is not available on the 7 lowest-numbered |
| // GPIO pads, and so the analog_io indexing is offset from the |
| // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io). |
| inout [`MPRJ_IO_PADS-10:0] analog_io, |
| |
| // Independent clock (on independent integer divider) |
| input user_clock2, |
| |
| // User maskable interrupt signals |
| output [2:0] user_irq |
| ); |
| |
| // generate active wires |
| wire [31: 0] active; |
| assign active = la_data_in[31:0]; |
| |
| // split remaining 96 logic analizer wires into 3 chunks |
| wire [31: 0] la1_data_in, la1_data_out, la1_oenb; |
| assign la1_data_in = la_data_in[63:32]; |
| assign la1_data_out = la_data_out[63:32]; |
| assign la1_oenb = la_oenb[63:32]; |
| |
| wire [31: 0] la2_data_in, la2_data_out, la2_oenb; |
| assign la2_data_in = la_data_in[95:64]; |
| assign la2_data_out = la_data_out[95:64]; |
| assign la2_oenb = la_oenb[95:64]; |
| |
| wire [31: 0] la3_data_in, la3_data_out, la3_oenb; |
| assign la3_data_in = la_data_in[127:96]; |
| assign la3_data_out = la_data_out[127:96]; |
| assign la3_oenb = la_oenb[127:96]; |
| |
| |
| |
| // Signals connecting user project to wishbone bridge |
| wire wbs_uprj_stb_i; |
| wire wbs_uprj_cyc_i; |
| wire wbs_uprj_we_i; |
| wire [3:0] wbs_uprj_sel_i; |
| wire [31:0] wbs_uprj_dat_i; |
| wire [31:0] wbs_uprj_adr_i; |
| wire wbs_uprj_ack_o; |
| wire [31:0] wbs_uprj_dat_o; |
| |
| // Signals connecting user project to OpenRAM via its wrapper |
| // shared openram wishbone bus wires |
| wire rambus_wb_clk_o; // clock |
| wire rambus_wb_rst_o; // reset |
| wire rambus_wb_stb_o; // write strobe |
| wire rambus_wb_cyc_o; // cycle |
| wire rambus_wb_we_o ; // write enable |
| wire [3:0] rambus_wb_sel_o; // write word select |
| wire [31:0] rambus_wb_dat_o; // ram data out |
| wire [9:0] rambus_wb_adr_o; // 10bit address |
| wire rambus_wb_ack_i; // ack |
| wire [31:0] rambus_wb_dat_i; // ram data in |
| |
| // Signals connecting OpenRAM wrapper to wishbone bridge |
| wire wbs_oram_stb_i; |
| wire wbs_oram_cyc_i; |
| wire wbs_oram_we_i; |
| wire [3:0] wbs_oram_sel_i; |
| wire [31:0] wbs_oram_dat_i; |
| wire [10:0] wbs_oram_adr_i; // 11bit address (latencies CSR + 1kB OpenRAM) |
| wire wbs_oram_ack_o; |
| wire [31:0] wbs_oram_dat_o; |
| |
| // Bridge splitting caravel wishbone traffic into two streams: user project and OpenRAM wrapper |
| wb_bridge_2way #( |
| .BUSB_ADDR_WIDTH(11) |
| ) wb_bridge_2way( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| // Wishbone UFP (Upward Facing Port) => caravel / picorv32 |
| .wb_clk_i (wb_clk_i), |
| .wb_rst_i (wb_rst_i), |
| .wbs_stb_i (wbs_stb_i), |
| .wbs_cyc_i (wbs_cyc_i), |
| .wbs_we_i (wbs_we_i), |
| .wbs_sel_i (wbs_sel_i[3:0]), |
| .wbs_dat_i (wbs_dat_i), |
| .wbs_adr_i (wbs_adr_i), |
| .wbs_ack_o (wbs_ack_o), |
| .wbs_dat_o (wbs_dat_o), |
| |
| // Wishbone A (Downward Facing Port) => user project |
| .wbm_a_stb_o (wbs_uprj_stb_i), |
| .wbm_a_cyc_o (wbs_uprj_cyc_i), |
| .wbm_a_we_o (wbs_uprj_we_i), |
| .wbm_a_sel_o (wbs_uprj_sel_i[3:0]), |
| .wbm_a_dat_i (wbs_uprj_dat_o[31:0]), |
| .wbm_a_adr_o (wbs_uprj_adr_i[31:0]), |
| .wbm_a_ack_i (wbs_uprj_ack_o), |
| .wbm_a_dat_o (wbs_uprj_dat_i[31:0]), |
| |
| // Wishbone B (Downward Facing Port) => OpenRAM wrapper/shim |
| .wbm_b_stb_o (wbs_oram_stb_i), |
| .wbm_b_cyc_o (wbs_oram_cyc_i), |
| .wbm_b_we_o (wbs_oram_we_i), |
| .wbm_b_sel_o (wbs_oram_sel_i[3:0]), |
| .wbm_b_dat_i (wbs_oram_dat_o[31:0]), |
| .wbm_b_adr_o (wbs_oram_adr_i[10:0]), |
| .wbm_b_ack_i (wbs_oram_ack_o), |
| .wbm_b_dat_o (wbs_oram_dat_i[31:0]) |
| ); |
| |
| // Signals connecting OpenRAM memory block to OpenRAM wrapper |
| wire oram_clk0; // clock |
| wire oram_csb0; // active low chip select |
| wire oram_web0; // active low write control |
| wire [3:0] oram_wmask0; // write (byte) mask |
| wire [7:0] oram_addr0; // address |
| wire [31:0] oram_din0; // data in |
| wire [31:0] oram_dout0; // data out |
| wire oram_clk1; // clock |
| wire oram_csb1; // active low chip select |
| wire [7:0] oram_addr1; // address |
| wire [31:0] oram_dout1; // data out |
| |
| // Dual port OpenRAM wrapper for wishbone |
| wb_openram_wrapper #( |
| .RAM_ADDR_WIDTH(8) |
| ) wb_openram_wrapper( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| // Selecting which port will be writable (0 -> A, 1 -> B) |
| .writable_port_req (active[31]), |
| |
| // Wishbone port A <= caravel (via wb_bridge) |
| .wb_a_clk_i (wb_clk_i), |
| .wb_a_rst_i (wb_rst_i), |
| .wbs_a_stb_i (wbs_oram_stb_i), |
| .wbs_a_cyc_i (wbs_oram_cyc_i), |
| .wbs_a_we_i (wbs_oram_we_i), |
| .wbs_a_sel_i (wbs_oram_sel_i[3:0]), |
| .wbs_a_dat_i (wbs_oram_dat_i[31:0]), |
| .wbs_a_adr_i (wbs_oram_adr_i[10:0]), |
| .wbs_a_ack_o (wbs_oram_ack_o), |
| .wbs_a_dat_o (wbs_oram_dat_o[31:0]), |
| |
| // Wishbone port B <= user project (rambus) |
| .wb_b_clk_i (rambus_wb_clk_o), |
| .wb_b_rst_i (rambus_wb_rst_o), |
| .wbs_b_stb_i (rambus_wb_stb_o), |
| .wbs_b_cyc_i (rambus_wb_cyc_o), |
| .wbs_b_we_i (rambus_wb_we_o), |
| .wbs_b_sel_i (rambus_wb_sel_o[3:0]), |
| .wbs_b_dat_i (rambus_wb_dat_o[31:0]), |
| .wbs_b_adr_i (rambus_wb_adr_o[9:0]), |
| .wbs_b_ack_o (rambus_wb_ack_i), |
| .wbs_b_dat_o (rambus_wb_dat_i[31:0]), |
| |
| // OpenRAM interface - almost dual port: RW + R |
| // Port 0: RW |
| .ram_clk0 (oram_clk0), |
| .ram_csb0 (oram_csb0), |
| .ram_web0 (oram_web0), |
| .ram_wmask0 (oram_wmask0[3:0]), |
| .ram_addr0 (oram_addr0[7:0]), |
| .ram_din0 (oram_din0[31:0]), |
| .ram_dout0 (oram_dout0[31:0]), |
| |
| // Port 1: R |
| .ram_clk1 (oram_clk1), |
| .ram_csb1 (oram_csb1), |
| .ram_addr1 (oram_addr1[7:0]), |
| .ram_dout1 (oram_dout1[31:0]) |
| ); |
| |
| |
| // OpenRAM block |
| sky130_sram_1kbyte_1rw1r_32x256_8 openram_1kB |
| ( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| |
| .clk0 (oram_clk0), |
| .csb0 (oram_csb0), |
| .web0 (oram_web0), |
| .wmask0 (oram_wmask0[3:0]), |
| .addr0 (oram_addr0[7:0]), |
| .din0 (oram_din0[31:0]), |
| .dout0 (oram_dout0[31:0]), |
| |
| .clk1 (oram_clk1), |
| .csb1 (oram_csb1), |
| .addr1 (oram_addr1[7:0]), |
| .dout1 (oram_dout1[31:0]) |
| ); |
| |
| |
| // start of user project module instantiation |
| wrapped_function_generator wrapped_function_generator_0( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]), |
| .wb_rst_i (wb_rst_i), |
| .wbs_stb_i (wbs_uprj_stb_i), |
| .wbs_cyc_i (wbs_uprj_cyc_i), |
| .wbs_we_i (wbs_uprj_we_i), |
| .wbs_sel_i (wbs_uprj_sel_i[3:0]), |
| .wbs_dat_i (wbs_uprj_dat_i[31:0]), |
| .wbs_adr_i (wbs_uprj_adr_i[31:0]), |
| .wbs_ack_o (wbs_uprj_ack_o), |
| .wbs_dat_o (wbs_uprj_dat_o[31:0]), |
| .rambus_wb_clk_o (rambus_wb_clk_o), |
| .rambus_wb_rst_o (rambus_wb_rst_o), |
| .rambus_wb_stb_o (rambus_wb_stb_o), |
| .rambus_wb_cyc_o (rambus_wb_cyc_o), |
| .rambus_wb_we_o (rambus_wb_we_o), |
| .rambus_wb_sel_o (rambus_wb_sel_o[3:0]), |
| .rambus_wb_dat_o (rambus_wb_dat_o[31:0]), |
| .rambus_wb_adr_o (rambus_wb_adr_o[9:0]), |
| .rambus_wb_ack_i (rambus_wb_ack_i), |
| .rambus_wb_dat_i (rambus_wb_dat_i[31:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_1( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[1]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_2( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[2]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_3( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[3]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_hack_soc_dffram wrapped_hack_soc_dffram_11( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[11]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_teras wrapped_teras_13( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[13]), |
| .wb_rst_i (wb_rst_i), |
| .wbs_stb_i (wbs_uprj_stb_i), |
| .wbs_cyc_i (wbs_uprj_cyc_i), |
| .wbs_we_i (wbs_uprj_we_i), |
| .wbs_sel_i (wbs_uprj_sel_i[3:0]), |
| .wbs_dat_i (wbs_uprj_dat_i[31:0]), |
| .wbs_adr_i (wbs_uprj_adr_i[31:0]), |
| .wbs_ack_o (wbs_uprj_ack_o), |
| .wbs_dat_o (wbs_uprj_dat_o[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_alu74181 wrapped_alu74181_7( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[7]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vgademo_on_fpga wrapped_vgademo_on_fpga_5( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[5]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_silife wrapped_silife_4( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[4]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]), |
| .wb_rst_i (wb_rst_i), |
| .wbs_stb_i (wbs_uprj_stb_i), |
| .wbs_cyc_i (wbs_uprj_cyc_i), |
| .wbs_we_i (wbs_uprj_we_i), |
| .wbs_sel_i (wbs_uprj_sel_i[3:0]), |
| .wbs_dat_i (wbs_uprj_dat_i[31:0]), |
| .wbs_adr_i (wbs_uprj_adr_i[31:0]), |
| .wbs_ack_o (wbs_uprj_ack_o), |
| .wbs_dat_o (wbs_uprj_dat_o[31:0]) |
| ); |
| |
| wrapped_acorn_prng wrapped_acorn_prng_9( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[9]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_hsv_mixer wrapped_hsv_mixer_10( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[10]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| // end of module instantiation |
| |
| endmodule // user_project_wrapper |
| `default_nettype wire |
