verilog/dv/test_c0/test_c0.c

/*
 * SPDX-FileCopyrightText: 2020 Efabless Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 * SPDX-License-Identifier: Apache-2.0
 */

// This include is relative to $CARAVEL_PATH (see Makefile)
#include "verilog/dv/caravel/defs.h"
#include "verilog/dv/caravel/stub.c"


void main()
{

	reg_spimaster_config = 0xa002;	// Enable, prescaler = 2,
                                        // connect to housekeeping SPI

	// RX and TX
	reg_mprj_io_0 =  GPIO_MODE_USER_STD_INPUT_NOPULL;
	reg_mprj_io_1 =  GPIO_MODE_USER_STD_OUTPUT;

	// Buyruk Geçerli
	reg_mprj_io_34 = GPIO_MODE_USER_STD_OUTPUT;
	
	// Program Sayacı
	reg_mprj_io_33 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_32 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_31 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_30 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_29 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_28 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_27 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_26 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_25 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_24 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_23 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_22 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_21 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_20 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_19 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_18 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_17 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_16 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_15 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_14 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_13 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_12 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_11 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_10 = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_9  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_8  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_7  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_6  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_5  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_4  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_3  = GPIO_MODE_USER_STD_OUTPUT;
	reg_mprj_io_2  = GPIO_MODE_USER_STD_OUTPUT;

	/* Apply configuration */
	reg_mprj_xfer = 1;
	while (reg_mprj_xfer == 1);

}