Add files via upload
diff --git a/verilog/dv/la_test1/Makefile b/verilog/dv/la_test1/Makefile
new file mode 100644
index 0000000..ba979f7
--- /dev/null
+++ b/verilog/dv/la_test1/Makefile
@@ -0,0 +1,96 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+## PDK
+PDK_PATH = $(PDK_ROOT)/sky130A
+
+## Caravel Pointers
+CARAVEL_ROOT ?= ../../../caravel
+CARAVEL_PATH ?= $(CARAVEL_ROOT)
+CARAVEL_FIRMWARE_PATH = $(CARAVEL_PATH)/verilog/dv/caravel
+CARAVEL_VERILOG_PATH = $(CARAVEL_PATH)/verilog
+CARAVEL_RTL_PATH = $(CARAVEL_VERILOG_PATH)/rtl
+CARAVEL_BEHAVIOURAL_MODELS = $(CARAVEL_VERILOG_PATH)/dv/caravel
+
+## User Project Pointers
+UPRJ_VERILOG_PATH ?= ../../../verilog
+UPRJ_RTL_PATH = $(UPRJ_VERILOG_PATH)/rtl
+UPRJ_BEHAVIOURAL_MODELS = ../
+
+## RISCV GCC
+GCC_PATH?=/ef/apps/bin
+GCC_PREFIX?=riscv32-unknown-elf
+
+## Simulation mode: RTL/GL
+SIM_DEFINES = -DFUNCTIONAL -DSIM
+SIM?=RTL
+
+.SUFFIXES:
+
+PATTERN = la_test1
+
+all: ${PATTERN:=.vcd}
+
+hex: ${PATTERN:=.hex}
+
+%.vvp: %_tb.v %.hex
+ifeq ($(SIM),RTL)
+ iverilog $(SIM_DEFINES) -I $(PDK_PATH) \
+ -I $(CARAVEL_BEHAVIOURAL_MODELS) -I $(CARAVEL_RTL_PATH) \
+ -I $(UPRJ_BEHAVIOURAL_MODELS) -I $(UPRJ_RTL_PATH) \
+ $< -o $@
+else
+ iverilog $(SIM_DEFINES) -DGL -I $(PDK_PATH) \
+ -I $(CARAVEL_BEHAVIOURAL_MODELS) -I $(CARAVEL_RTL_PATH) -I $(CARAVEL_VERILOG_PATH) \
+ -I $(UPRJ_BEHAVIOURAL_MODELS) -I$(UPRJ_RTL_PATH) -I $(UPRJ_VERILOG_PATH) \
+ $< -o $@
+endif
+
+%.vcd: %.vvp
+ vvp $<
+
+%.elf: %.c $(CARAVEL_FIRMWARE_PATH)/sections.lds $(CARAVEL_FIRMWARE_PATH)/start.s check-env
+ ${GCC_PATH}/${GCC_PREFIX}-gcc -I $(CARAVEL_PATH) -march=rv32imc -mabi=ilp32 -Wl,-Bstatic,-T,$(CARAVEL_FIRMWARE_PATH)/sections.lds,--strip-debug -ffreestanding -nostdlib -o $@ $(CARAVEL_FIRMWARE_PATH)/start.s $<
+
+%.hex: %.elf
+ ${GCC_PATH}/${GCC_PREFIX}-objcopy -O verilog $< $@
+ # to fix flash base address
+ sed -i 's/@10000000/@00000000/g' $@
+
+%.bin: %.elf
+ ${GCC_PATH}/${GCC_PREFIX}-objcopy -O binary $< /dev/stdout | tail -c +1048577 > $@
+
+check-env:
+ifndef PDK_ROOT
+ $(error PDK_ROOT is undefined, please export it before running make)
+endif
+ifeq (,$(wildcard $(PDK_ROOT)/sky130A))
+ $(error $(PDK_ROOT)/sky130A not found, please install pdk before running make)
+endif
+ifeq (,$(wildcard $(GCC_PATH)/$(GCC_PREFIX)-gcc ))
+ $(error $(GCC_PATH)/$(GCC_PREFIX)-gcc is not found, please export GCC_PATH and GCC_PREFIX before running make)
+endif
+# check for efabless style installation
+ifeq (,$(wildcard $(PDK_ROOT)/sky130A/libs.ref/*/verilog))
+SIM_DEFINES := ${SIM_DEFINES} -DEF_STYLE
+endif
+
+# ---- Clean ----
+
+clean:
+ rm -f *.elf *.hex *.bin *.vvp *.vcd *.log
+
+.PHONY: clean hex all
diff --git a/verilog/dv/la_test1/la_test1.c b/verilog/dv/la_test1/la_test1.c
new file mode 100644
index 0000000..220bdfe
--- /dev/null
+++ b/verilog/dv/la_test1/la_test1.c
@@ -0,0 +1,124 @@
+/*
+ * SPDX-FileCopyrightText: 2020 Efabless Corporation
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+// This include is relative to $CARAVEL_PATH (see Makefile)
+#include "verilog/dv/caravel/defs.h"
+#include "verilog/dv/caravel/stub.c"
+
+// --------------------------------------------------------
+
+/*
+ MPRJ Logic Analyzer Test:
+ - Observes counter value through LA probes [31:0]
+ - Sets counter initial value through LA probes [63:32]
+ - Flags when counter value exceeds 500 through the management SoC gpio
+ - Outputs message to the UART when the test concludes successfuly
+*/
+
+void main()
+{
+
+ /* Set up the housekeeping SPI to be connected internally so */
+ /* that external pin changes don't affect it. */
+
+ reg_spimaster_config = 0xa002; // Enable, prescaler = 2,
+ // connect to housekeeping SPI
+
+ // Connect the housekeeping SPI to the SPI master
+ // so that the CSB line is not left floating. This allows
+ // all of the GPIO pins to be used for user functions.
+
+ // The upper GPIO pins are configured to be output
+ // and accessble to the management SoC.
+ // Used to flad the start/end of a test
+ // The lower GPIO pins are configured to be output
+ // and accessible to the user project. They show
+ // the project count value, although this test is
+ // designed to read the project count through the
+ // logic analyzer probes.
+ // I/O 6 is configured for the UART Tx line
+
+ reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;
+
+ reg_mprj_io_15 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_14 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_13 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_12 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_11 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_10 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_9 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_8 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_7 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_5 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_4 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_3 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_2 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_1 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_0 = GPIO_MODE_USER_STD_OUTPUT;
+
+ reg_mprj_io_6 = GPIO_MODE_MGMT_STD_OUTPUT;
+
+ // Set UART clock to 64 kbaud (enable before I/O configuration)
+ reg_uart_clkdiv = 625;
+ reg_uart_enable = 1;
+
+ /* Apply configuration */
+ reg_mprj_xfer = 1;
+ while (reg_mprj_xfer == 1);
+
+ // Configure LA probes [31:0], [127:64] as inputs to the cpu
+ // Configure LA probes [63:32] as outputs from the cpu
+ reg_la0_oenb = reg_la0_iena = 0xFFFFFFFF; // [31:0]
+ reg_la1_oenb = reg_la1_iena = 0x00000000; // [63:32]
+ reg_la2_oenb = reg_la2_iena = 0xFFFFFFFF; // [95:64]
+ reg_la3_oenb = reg_la3_iena = 0xFFFFFFFF; // [127:96]
+
+ // Flag start of the test
+ reg_mprj_datal = 0xAB400000;
+
+ // Set Counter value to zero through LA probes [63:32]
+ reg_la1_data = 0x00000000;
+
+ // Configure LA probes from [63:32] as inputs to disable counter write
+ reg_la1_oenb = reg_la1_iena = 0xFFFFFFFF;
+
+ while (1) {
+ if (reg_la0_data > 0x1F4) {
+ reg_mprj_datal = 0xAB410000;
+ break;
+ }
+ }
+ print("\n");
+ print("Monitor: Test 2 Passed\n\n"); // Makes simulation very long!
+ reg_mprj_datal = 0xAB510000;
+}
+
diff --git a/verilog/dv/la_test1/la_test1_tb.v b/verilog/dv/la_test1/la_test1_tb.v
new file mode 100644
index 0000000..626e390
--- /dev/null
+++ b/verilog/dv/la_test1/la_test1_tb.v
@@ -0,0 +1,149 @@
+// SPDX-FileCopyrightText: 2020 Efabless Corporation
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+
+`default_nettype none
+
+`timescale 1 ns / 1 ps
+
+`include "uprj_netlists.v"
+`include "caravel_netlists.v"
+`include "spiflash.v"
+`include "tbuart.v"
+
+module la_test1_tb;
+ reg clock;
+ reg RSTB;
+ reg CSB;
+
+ reg power1, power2;
+
+ wire gpio;
+ wire uart_tx;
+ wire [37:0] mprj_io;
+ wire [15:0] checkbits;
+
+ assign checkbits = mprj_io[31:16];
+ assign uart_tx = mprj_io[6];
+
+ always #12.5 clock <= (clock === 1'b0);
+
+ initial begin
+ clock = 0;
+ end
+
+ assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz;
+
+ initial begin
+ // $dumpfile("la_test1.vcd");
+ // $dumpvars(0, la_test1_tb);
+
+ // Repeat cycles of 1000 clock edges as needed to complete testbench
+ repeat (200) begin
+ repeat (1000) @(posedge clock);
+ // $display("+1000 cycles");
+ end
+ $display("%c[1;31m",27);
+ `ifdef GL
+ $display ("Monitor: Timeout, Test LA (GL) Failed");
+ `else
+ $display ("Monitor: Timeout, Test LA (RTL) Failed");
+ `endif
+ $display("%c[0m",27);
+ $finish;
+ end
+
+ initial begin
+ wait(checkbits == 16'hAB40);
+ $display("LA Test 1 started");
+ wait(checkbits == 16'hAB41);
+ wait(checkbits == 16'hAB51);
+ #10000;
+ $finish;
+ end
+
+ initial begin
+ RSTB <= 1'b0;
+ CSB <= 1'b1; // Force CSB high
+ #2000;
+ RSTB <= 1'b1; // Release reset
+ #170000;
+ CSB = 1'b0; // CSB can be released
+ end
+
+ initial begin // Power-up sequence
+ power1 <= 1'b0;
+ power2 <= 1'b0;
+ #200;
+ power1 <= 1'b1;
+ #200;
+ power2 <= 1'b1;
+ end
+
+ wire flash_csb;
+ wire flash_clk;
+ wire flash_io0;
+ wire flash_io1;
+
+ wire VDD1V8;
+ wire VDD3V3;
+ wire VSS;
+
+ assign VDD3V3 = power1;
+ assign VDD1V8 = power2;
+ assign VSS = 1'b0;
+
+ caravel uut (
+ .vddio (VDD3V3),
+ .vssio (VSS),
+ .vdda (VDD3V3),
+ .vssa (VSS),
+ .vccd (VDD1V8),
+ .vssd (VSS),
+ .vdda1 (VDD3V3),
+ .vdda2 (VDD3V3),
+ .vssa1 (VSS),
+ .vssa2 (VSS),
+ .vccd1 (VDD1V8),
+ .vccd2 (VDD1V8),
+ .vssd1 (VSS),
+ .vssd2 (VSS),
+ .clock (clock),
+ .gpio (gpio),
+ .mprj_io (mprj_io),
+ .flash_csb(flash_csb),
+ .flash_clk(flash_clk),
+ .flash_io0(flash_io0),
+ .flash_io1(flash_io1),
+ .resetb (RSTB)
+ );
+
+ spiflash #(
+ .FILENAME("la_test1.hex")
+ ) spiflash (
+ .csb(flash_csb),
+ .clk(flash_clk),
+ .io0(flash_io0),
+ .io1(flash_io1),
+ .io2(), // not used
+ .io3() // not used
+ );
+
+ // Testbench UART
+ tbuart tbuart (
+ .ser_rx(uart_tx)
+ );
+
+endmodule
+`default_nettype wire
diff --git a/verilog/dv/la_test2/Makefile b/verilog/dv/la_test2/Makefile
new file mode 100644
index 0000000..0435500
--- /dev/null
+++ b/verilog/dv/la_test2/Makefile
@@ -0,0 +1,96 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+## PDK
+PDK_PATH = $(PDK_ROOT)/sky130A
+
+## Caravel Pointers
+CARAVEL_ROOT ?= ../../../caravel
+CARAVEL_PATH ?= $(CARAVEL_ROOT)
+CARAVEL_FIRMWARE_PATH = $(CARAVEL_PATH)/verilog/dv/caravel
+CARAVEL_VERILOG_PATH = $(CARAVEL_PATH)/verilog
+CARAVEL_RTL_PATH = $(CARAVEL_VERILOG_PATH)/rtl
+CARAVEL_BEHAVIOURAL_MODELS = $(CARAVEL_VERILOG_PATH)/dv/caravel
+
+## User Project Pointers
+UPRJ_VERILOG_PATH ?= ../../../verilog
+UPRJ_RTL_PATH = $(UPRJ_VERILOG_PATH)/rtl
+UPRJ_BEHAVIOURAL_MODELS = ../
+
+## RISCV GCC
+GCC_PATH?=/ef/apps/bin
+GCC_PREFIX?=riscv32-unknown-elf
+
+## Simulation mode: RTL/GL
+SIM_DEFINES = -DFUNCTIONAL -DSIM
+SIM?=RTL
+
+.SUFFIXES:
+
+PATTERN = la_test2
+
+all: ${PATTERN:=.vcd}
+
+hex: ${PATTERN:=.hex}
+
+%.vvp: %_tb.v %.hex
+ifeq ($(SIM),RTL)
+ iverilog $(SIM_DEFINES) -I $(PDK_PATH) \
+ -I $(CARAVEL_BEHAVIOURAL_MODELS) -I $(CARAVEL_RTL_PATH) \
+ -I $(UPRJ_BEHAVIOURAL_MODELS) -I $(UPRJ_RTL_PATH) \
+ $< -o $@
+else
+ iverilog $(SIM_DEFINES) -DGL -I $(PDK_PATH) \
+ -I $(CARAVEL_BEHAVIOURAL_MODELS) -I $(CARAVEL_RTL_PATH) -I $(CARAVEL_VERILOG_PATH) \
+ -I $(UPRJ_BEHAVIOURAL_MODELS) -I$(UPRJ_RTL_PATH) -I $(UPRJ_VERILOG_PATH) \
+ $< -o $@
+endif
+
+%.vcd: %.vvp
+ vvp $<
+
+%.elf: %.c $(CARAVEL_FIRMWARE_PATH)/sections.lds $(CARAVEL_FIRMWARE_PATH)/start.s check-env
+ ${GCC_PATH}/${GCC_PREFIX}-gcc -I $(CARAVEL_PATH) -march=rv32imc -mabi=ilp32 -Wl,-Bstatic,-T,$(CARAVEL_FIRMWARE_PATH)/sections.lds,--strip-debug -ffreestanding -nostdlib -o $@ $(CARAVEL_FIRMWARE_PATH)/start.s $<
+
+%.hex: %.elf
+ ${GCC_PATH}/${GCC_PREFIX}-objcopy -O verilog $< $@
+ # to fix flash base address
+ sed -i 's/@10000000/@00000000/g' $@
+
+%.bin: %.elf
+ ${GCC_PATH}/${GCC_PREFIX}-objcopy -O binary $< /dev/stdout | tail -c +1048577 > $@
+
+check-env:
+ifndef PDK_ROOT
+ $(error PDK_ROOT is undefined, please export it before running make)
+endif
+ifeq (,$(wildcard $(PDK_ROOT)/sky130A))
+ $(error $(PDK_ROOT)/sky130A not found, please install pdk before running make)
+endif
+ifeq (,$(wildcard $(GCC_PATH)/$(GCC_PREFIX)-gcc ))
+ $(error $(GCC_PATH)/$(GCC_PREFIX)-gcc is not found, please export GCC_PATH and GCC_PREFIX before running make)
+endif
+# check for efabless style installation
+ifeq (,$(wildcard $(PDK_ROOT)/sky130A/libs.ref/*/verilog))
+SIM_DEFINES := ${SIM_DEFINES} -DEF_STYLE
+endif
+
+# ---- Clean ----
+
+clean:
+ rm -f *.elf *.hex *.bin *.vvp *.vcd *.log
+
+.PHONY: clean hex all
diff --git a/verilog/dv/la_test2/la_test2.c b/verilog/dv/la_test2/la_test2.c
new file mode 100644
index 0000000..5875432
--- /dev/null
+++ b/verilog/dv/la_test2/la_test2.c
@@ -0,0 +1,114 @@
+/*
+ * SPDX-FileCopyrightText: 2020 Efabless Corporation
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License");
+ * you may not use this file except in compliance with the License.
+ * You may obtain a copy of the License at
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software
+ * distributed under the License is distributed on an "AS IS" BASIS,
+ * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+ * See the License for the specific language governing permissions and
+ * limitations under the License.
+ * SPDX-License-Identifier: Apache-2.0
+ */
+
+// This include is relative to $CARAVEL_PATH (see Makefile)
+#include "verilog/dv/caravel/defs.h"
+#include "verilog/dv/caravel/stub.c"
+
+/*
+ MPRJ LA Test:
+ - Sets counter clk through LA[64]
+ - Sets counter rst through LA[65]
+ - Observes count value for five clk cycle through LA[31:0]
+*/
+
+int clk = 0;
+int i;
+
+void main()
+{
+ /* Set up the housekeeping SPI to be connected internally so */
+ /* that external pin changes don't affect it. */
+
+ reg_spimaster_config = 0xa002; // Enable, prescaler = 2,
+ // connect to housekeeping SPI
+
+ // Connect the housekeeping SPI to the SPI master
+ // so that the CSB line is not left floating. This allows
+ // all of the GPIO pins to be used for user functions.
+
+
+ // All GPIO pins are configured to be output
+ // Used to flad the start/end of a test
+
+ reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
+ reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;
+
+ reg_mprj_io_15 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_14 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_13 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_12 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_11 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_10 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_9 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_8 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_7 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_5 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_4 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_3 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_2 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_1 = GPIO_MODE_USER_STD_OUTPUT;
+ reg_mprj_io_0 = GPIO_MODE_USER_STD_OUTPUT;
+
+ /* Apply configuration */
+ reg_mprj_xfer = 1;
+ while (reg_mprj_xfer == 1);
+
+ // Configure All LA probes as inputs to the cpu
+ reg_la0_oenb = reg_la0_iena = 0xFFFFFFFF; // [31:0]
+ reg_la1_oenb = reg_la1_iena = 0xFFFFFFFF; // [63:32]
+ reg_la2_oenb = reg_la2_iena = 0xFFFFFFFF; // [95:64]
+ reg_la3_oenb = reg_la3_iena = 0xFFFFFFFF; // [127:96]
+
+ // Flag start of the test
+ reg_mprj_datal = 0xAB600000;
+
+ // Configure LA[64] LA[65] as outputs from the cpu
+ reg_la2_oenb = reg_la2_iena = 0xFFFFFFFC;
+
+ // Set clk & reset to one
+ reg_la2_data = 0x00000003;
+
+ // DELAY
+ for (i=0; i<5; i=i+1) {}
+
+ // Toggle clk & de-assert reset
+ for (i=0; i<11; i=i+1) {
+ clk = !clk;
+ reg_la2_data = 0x00000000 | clk;
+ }
+
+ if (reg_la0_data >= 0x05) {
+ reg_mprj_datal = 0xAB610000;
+ }
+
+}
+
diff --git a/verilog/dv/la_test2/la_test2_tb.v b/verilog/dv/la_test2/la_test2_tb.v
new file mode 100644
index 0000000..e09905e
--- /dev/null
+++ b/verilog/dv/la_test2/la_test2_tb.v
@@ -0,0 +1,139 @@
+// SPDX-FileCopyrightText: 2020 Efabless Corporation
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+
+`default_nettype none
+
+`timescale 1 ns / 1 ps
+
+`include "uprj_netlists.v"
+`include "caravel_netlists.v"
+`include "spiflash.v"
+
+module la_test2_tb;
+ reg clock;
+ reg RSTB;
+ reg CSB;
+
+ reg power1, power2;
+
+ wire gpio;
+ wire [37:0] mprj_io;
+ wire [15:0] checkbits;
+
+ assign checkbits = mprj_io[31:16];
+ assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz;
+
+ always #12.5 clock <= (clock === 1'b0);
+
+ initial begin
+ clock = 0;
+ end
+
+ initial begin
+ $dumpfile("la_test2.vcd");
+ $dumpvars(0, la_test2_tb);
+
+ // Repeat cycles of 1000 clock edges as needed to complete testbench
+ repeat (30) begin
+ repeat (1000) @(posedge clock);
+ // $display("+1000 cycles");
+ end
+ $display("%c[1;31m",27);
+ `ifdef GL
+ $display ("Monitor: Timeout, Test Mega-Project IO (GL) Failed");
+ `else
+ $display ("Monitor: Timeout, Test Mega-Project IO (RTL) Failed");
+ `endif
+ $display("%c[0m",27);
+ $finish;
+ end
+
+ initial begin
+ wait(checkbits == 16'h AB60);
+ $display("Monitor: Test 2 MPRJ-Logic Analyzer Started");
+ wait(checkbits == 16'h AB61);
+ $display("Monitor: Test 2 MPRJ-Logic Analyzer Passed");
+ $finish;
+ end
+
+ initial begin
+ RSTB <= 1'b0;
+ CSB <= 1'b1; // Force CSB high
+ #2000;
+ RSTB <= 1'b1; // Release reset
+ #170000;
+ CSB = 1'b0; // CSB can be released
+ end
+
+ initial begin // Power-up sequence
+ power1 <= 1'b0;
+ power2 <= 1'b0;
+ #200;
+ power1 <= 1'b1;
+ #200;
+ power2 <= 1'b1;
+ end
+
+ wire flash_csb;
+ wire flash_clk;
+ wire flash_io0;
+ wire flash_io1;
+
+ wire VDD1V8;
+ wire VDD3V3;
+ wire VSS;
+
+ assign VDD3V3 = power1;
+ assign VDD1V8 = power2;
+ assign VSS = 1'b0;
+
+ caravel uut (
+ .vddio (VDD3V3),
+ .vssio (VSS),
+ .vdda (VDD3V3),
+ .vssa (VSS),
+ .vccd (VDD1V8),
+ .vssd (VSS),
+ .vdda1 (VDD3V3),
+ .vdda2 (VDD3V3),
+ .vssa1 (VSS),
+ .vssa2 (VSS),
+ .vccd1 (VDD1V8),
+ .vccd2 (VDD1V8),
+ .vssd1 (VSS),
+ .vssd2 (VSS),
+ .clock (clock),
+ .gpio (gpio),
+ .mprj_io (mprj_io),
+ .flash_csb(flash_csb),
+ .flash_clk(flash_clk),
+ .flash_io0(flash_io0),
+ .flash_io1(flash_io1),
+ .resetb (RSTB)
+ );
+
+ spiflash #(
+ .FILENAME("la_test2.hex")
+ ) spiflash (
+ .csb(flash_csb),
+ .clk(flash_clk),
+ .io0(flash_io0),
+ .io1(flash_io1),
+ .io2(),
+ .io3()
+ );
+
+endmodule
+`default_nettype wire
