Delete user_project_wrapper.v
diff --git a/caravel/verilog/rtl/user_project_wrapper.v b/caravel/verilog/rtl/user_project_wrapper.v
deleted file mode 100644
index 4b72efc..0000000
--- a/caravel/verilog/rtl/user_project_wrapper.v
+++ /dev/null
@@ -1,110 +0,0 @@
-// SPDX-FileCopyrightText: 2020 Efabless Corporation
-//
-// Licensed under the Apache License, Version 2.0 (the "License");
-// you may not use this file except in compliance with the License.
-// You may obtain a copy of the License at
-//
-// http://www.apache.org/licenses/LICENSE-2.0
-//
-// Unless required by applicable law or agreed to in writing, software
-// distributed under the License is distributed on an "AS IS" BASIS,
-// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-// See the License for the specific language governing permissions and
-// limitations under the License.
-// SPDX-License-Identifier: Apache-2.0
-
-`default_nettype none
-/*
- *-------------------------------------------------------------
- *
- * user_project_wrapper
- *
- * This wrapper enumerates all of the pins available to the
- * user for the user project.
- *
- * An example user project is provided in this wrapper. The
- * example should be removed and replaced with the actual
- * user project.
- *
- *-------------------------------------------------------------
- */
-
-module user_project_wrapper #(
- parameter BITS = 32
-) (
-`ifdef USE_POWER_PINS
- inout vdda1, // User area 1 3.3V supply
- inout vdda2, // User area 2 3.3V supply
- inout vssa1, // User area 1 analog ground
- inout vssa2, // User area 2 analog ground
- inout vccd1, // User area 1 1.8V supply
- inout vccd2, // User area 2 1.8v supply
- inout vssd1, // User area 1 digital ground
- inout vssd2, // User area 2 digital ground
-`endif
-
- // Wishbone Slave ports (WB MI A)
- input wb_clk_i,
- input wb_rst_i,
- input wbs_stb_i,
- input wbs_cyc_i,
- input wbs_we_i,
- input [3:0] wbs_sel_i,
- input [31:0] wbs_dat_i,
- input [31:0] wbs_adr_i,
- output wbs_ack_o,
- output [31:0] wbs_dat_o,
-
- // Logic Analyzer Signals
- input [127:0] la_data_in,
- output [127:0] la_data_out,
- input [127:0] la_oenb,
-
- // IOs
- input [`MPRJ_IO_PADS-1:0] io_in,
- output [`MPRJ_IO_PADS-1:0] io_out,
- output [`MPRJ_IO_PADS-1:0] io_oeb,
-
- // Analog (direct connection to GPIO pad---use with caution)
- // Note that analog I/O is not available on the 7 lowest-numbered
- // GPIO pads, and so the analog_io indexing is offset from the
- // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
- inout [`MPRJ_IO_PADS-10:0] analog_io,
-
- // Independent clock (on independent integer divider)
- input user_clock2,
-
- // User maskable interrupt signals
- output [2:0] user_irq
-);
-
-/*--------------------------------------*/
-/* User project is instantiated here */
-/*--------------------------------------*/
-
-
-user_proj_example mprj (
- `ifdef USE_POWER_PINS
- .vdda1(vdda1), // User area 1 3.3V power
- .vdda2(vdda2), // User area 2 3.3V power
- .vssa1(vssa1), // User area 1 analog ground
- .vssa2(vssa2), // User area 2 analog ground
- .vccd1(vccd1), // User area 1 1.8V power
- .vccd2(vccd2), // User area 2 1.8V power
- .vssd1(vssd1), // User area 1 digital ground
- .vssd2(vssd2), // User area 2 digital ground
- `endif
-
-
- // IOs
- .io_in (io_in),
- .io_out (io_out),
- .analog_io (analog_io),
- .io_oeb(io_oeb)
-
-
- );
-
-endmodule // user_project_wrapper
-
-`default_nettype wire
