diff --git a/caravel/verilog/rtl/user_project_wrapper.v b/caravel/verilog/rtl/user_project_wrapper.v
deleted file mode 100644
index 4b72efc..0000000
--- a/caravel/verilog/rtl/user_project_wrapper.v
+++ /dev/null
@@ -1,110 +0,0 @@
-// SPDX-FileCopyrightText: 2020 Efabless Corporation
-//
-// Licensed under the Apache License, Version 2.0 (the "License");
-// you may not use this file except in compliance with the License.
-// You may obtain a copy of the License at
-//
-//      http://www.apache.org/licenses/LICENSE-2.0
-//
-// Unless required by applicable law or agreed to in writing, software
-// distributed under the License is distributed on an "AS IS" BASIS,
-// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
-// See the License for the specific language governing permissions and
-// limitations under the License.
-// SPDX-License-Identifier: Apache-2.0
-
-`default_nettype none
-/*
- *-------------------------------------------------------------
- *
- * user_project_wrapper
- *
- * This wrapper enumerates all of the pins available to the
- * user for the user project.
- *
- * An example user project is provided in this wrapper.  The
- * example should be removed and replaced with the actual
- * user project.
- *
- *-------------------------------------------------------------
- */
-
-module user_project_wrapper #(
-    parameter BITS = 32
-) (
-`ifdef USE_POWER_PINS
-    inout vdda1,	// User area 1 3.3V supply
-    inout vdda2,	// User area 2 3.3V supply
-    inout vssa1,	// User area 1 analog ground
-    inout vssa2,	// User area 2 analog ground
-    inout vccd1,	// User area 1 1.8V supply
-    inout vccd2,	// User area 2 1.8v supply
-    inout vssd1,	// User area 1 digital ground
-    inout vssd2,	// User area 2 digital ground
-`endif
-
-    // Wishbone Slave ports (WB MI A)
-    input wb_clk_i,
-    input wb_rst_i,
-    input wbs_stb_i,
-    input wbs_cyc_i,
-    input wbs_we_i,
-    input [3:0] wbs_sel_i,
-    input [31:0] wbs_dat_i,
-    input [31:0] wbs_adr_i,
-    output wbs_ack_o,
-    output [31:0] wbs_dat_o,
-
-    // Logic Analyzer Signals
-    input  [127:0] la_data_in,
-    output [127:0] la_data_out,
-    input  [127:0] la_oenb,
-
-    // IOs
-    input  [`MPRJ_IO_PADS-1:0] io_in,
-    output [`MPRJ_IO_PADS-1:0] io_out,
-    output [`MPRJ_IO_PADS-1:0] io_oeb,
-
-    // Analog (direct connection to GPIO pad---use with caution)
-    // Note that analog I/O is not available on the 7 lowest-numbered
-    // GPIO pads, and so the analog_io indexing is offset from the
-    // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
-    inout [`MPRJ_IO_PADS-10:0] analog_io,
-
-    // Independent clock (on independent integer divider)
-    input   user_clock2,
-
-    // User maskable interrupt signals
-    output [2:0] user_irq
-);
-
-/*--------------------------------------*/
-/* User project is instantiated  here   */
-/*--------------------------------------*/
-
-
-user_proj_example mprj (
-    `ifdef USE_POWER_PINS
-	.vdda1(vdda1),	// User area 1 3.3V power
-	.vdda2(vdda2),	// User area 2 3.3V power
-	.vssa1(vssa1),	// User area 1 analog ground
-	.vssa2(vssa2),	// User area 2 analog ground
-	.vccd1(vccd1),	// User area 1 1.8V power
-	.vccd2(vccd2),	// User area 2 1.8V power
-	.vssd1(vssd1),	// User area 1 digital ground
-	.vssd2(vssd2),	// User area 2 digital ground
-    `endif
-
-    
-        // IOs
-        .io_in      (io_in),
-        .io_out	(io_out),
-        .analog_io     (analog_io),
-        .io_oeb(io_oeb)
-
-
-        );
-	
-endmodule	// user_project_wrapper
-
-`default_nettype wire