blob: 586d9a6a19e89b5f26e64e035e344eb3d62059c0 [file] [log] [blame]
`ifdef SIM
`default_nettype wire
`endif
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
/*--------------------------------------------------------------*/
/* caravel, a project harness for the Google/SkyWater sky130 */
/* fabrication process and open source PDK */
/* */
/* Copyright 2020 efabless, Inc. */
/* Written by Tim Edwards, December 2019 */
/* and Mohamed Shalan, August 2020 */
/* This file is open source hardware released under the */
/* Apache 2.0 license. See file LICENSE. */
/* */
/* Updated 10/15/2021: Revised using the housekeeping module */
/* from housekeeping.v (refactoring a number of functions from */
/* the management SoC). */
/* */
/*--------------------------------------------------------------*/
module caravel (
// All top-level I/O are package-facing pins
inout vddio, // Common 3.3V padframe/ESD power
inout vddio_2, // Common 3.3V padframe/ESD power
inout vssio, // Common padframe/ESD ground
inout vssio_2, // Common padframe/ESD ground
inout vdda, // Management 3.3V power
inout vssa, // Common analog ground
inout vccd, // Management/Common 1.8V power
inout vssd, // Common digital ground
inout vdda1, // User area 1 3.3V power
inout vdda1_2, // User area 1 3.3V power
inout vdda2, // User area 2 3.3V power
inout vssa1, // User area 1 analog ground
inout vssa1_2, // User area 1 analog ground
inout vssa2, // User area 2 analog ground
inout vccd1, // User area 1 1.8V power
inout vccd2, // User area 2 1.8V power
inout vssd1, // User area 1 digital ground
inout vssd2, // User area 2 digital ground
inout gpio, // Used for external LDO control
inout [`MPRJ_IO_PADS-1:0] mprj_io,
input clock, // CMOS core clock input, not a crystal
input resetb, // Reset input (sense inverted)
// Note that only two flash data pins are dedicated to the
// management SoC wrapper. The management SoC exports the
// quad SPI mode status to make use of the top two mprj_io
// pins for io2 and io3.
output flash_csb,
output flash_clk,
output flash_io0,
output flash_io1
);
//------------------------------------------------------------
// This value is uniquely defined for each user project.
//------------------------------------------------------------
parameter USER_PROJECT_ID = 32'h0002000c;
/*
*--------------------------------------------------------------------
*
* These pins are overlaid on mprj_io space. They have the function
* below when the management processor is in reset, or in the default
* configuration. They are assigned to uses in the user space by the
* configuration program running off of the SPI flash. Note that even
* when the user has taken control of these pins, they can be restored
* to the original use by setting the resetb pin low. The SPI pins and
* UART pins can be connected directly to an FTDI chip as long as the
* FTDI chip sets these lines to high impedence (input function) at
* all times except when holding the chip in reset.
*
* JTAG = mprj_io[0] (inout)
* SDO = mprj_io[1] (output)
* SDI = mprj_io[2] (input)
* CSB = mprj_io[3] (input)
* SCK = mprj_io[4] (input)
* ser_rx = mprj_io[5] (input)
* ser_tx = mprj_io[6] (output)
* irq = mprj_io[7] (input)
*
* spi_sck = mprj_io[32] (output)
* spi_csb = mprj_io[33] (output)
* spi_sdi = mprj_io[34] (input)
* spi_sdo = mprj_io[35] (output)
* flash_io2 = mprj_io[36] (inout)
* flash_io3 = mprj_io[37] (inout)
*
* These pins are reserved for any project that wants to incorporate
* its own processor and flash controller. While a user project can
* technically use any available I/O pins for the purpose, these
* four pins connect to a pass-through mode from the SPI slave (pins
* 1-4 above) so that any SPI flash connected to these specific pins
* can be accessed through the SPI slave even when the processor is in
* reset.
*
* user_flash_csb = mprj_io[8]
* user_flash_sck = mprj_io[9]
* user_flash_io0 = mprj_io[10]
* user_flash_io1 = mprj_io[11]
*
*--------------------------------------------------------------------
*/
// One-bit GPIO dedicated to management SoC (outside of user control)
wire gpio_out_core;
wire gpio_in_core;
wire gpio_mode0_core;
wire gpio_mode1_core;
wire gpio_outenb_core;
wire gpio_inenb_core;
// User Project Control (pad-facing)
wire [`MPRJ_IO_PADS-1:0] mprj_io_inp_dis;
wire [`MPRJ_IO_PADS-1:0] mprj_io_oeb;
wire [`MPRJ_IO_PADS-1:0] mprj_io_ib_mode_sel;
wire [`MPRJ_IO_PADS-1:0] mprj_io_vtrip_sel;
wire [`MPRJ_IO_PADS-1:0] mprj_io_slow_sel;
wire [`MPRJ_IO_PADS-1:0] mprj_io_holdover;
wire [`MPRJ_IO_PADS-1:0] mprj_io_analog_en;
wire [`MPRJ_IO_PADS-1:0] mprj_io_analog_sel;
wire [`MPRJ_IO_PADS-1:0] mprj_io_analog_pol;
wire [`MPRJ_IO_PADS*3-1:0] mprj_io_dm;
wire [`MPRJ_IO_PADS-1:0] mprj_io_in;
wire [`MPRJ_IO_PADS-1:0] mprj_io_out;
// User Project Control (user-facing)
wire [`MPRJ_IO_PADS-1:0] user_io_oeb;
wire [`MPRJ_IO_PADS-1:0] user_io_in;
wire [`MPRJ_IO_PADS-1:0] user_io_out;
wire [`MPRJ_IO_PADS-10:0] user_analog_io;
/* Padframe control signals */
wire [`MPRJ_IO_PADS_1-1:0] gpio_serial_link_1;
wire [`MPRJ_IO_PADS_2-1:0] gpio_serial_link_2;
wire mprj_io_loader_resetn;
wire mprj_io_loader_clock;
wire mprj_io_loader_strobe;
wire mprj_io_loader_data_1; /* user1 side serial loader */
wire mprj_io_loader_data_2; /* user2 side serial loader */
// User Project Control management I/O
// There are two types of GPIO connections:
// (1) Full Bidirectional: Management connects to in, out, and oeb
// Uses: JTAG and SDO
// (2) Selectable bidirectional: Management connects to in and out,
// which are tied together. oeb is grounded (oeb from the
// configuration is used)
// SDI = mprj_io[2] (input)
// CSB = mprj_io[3] (input)
// SCK = mprj_io[4] (input)
// ser_rx = mprj_io[5] (input)
// ser_tx = mprj_io[6] (output)
// irq = mprj_io[7] (input)
wire [`MPRJ_IO_PADS-1:0] mgmt_io_in; /* one- and three-pin data */
wire [`MPRJ_IO_PADS-5:0] mgmt_io_nc; /* no-connects */
wire [4:0] mgmt_io_out; /* three-pin interface out */
wire [4:0] mgmt_io_oeb; /* three-pin output enable */
wire [`MPRJ_PWR_PADS-1:0] pwr_ctrl_nc; /* no-connects */
wire clock_core;
// Power-on-reset signal. The reset pad generates the sense-inverted
// reset at 3.3V. The 1.8V signal and the inverted 1.8V signal are
// derived.
wire porb_h;
wire porb_l;
wire por_l;
wire rstb_h;
wire rstb_l;
// Flash SPI communication (management SoC to housekeeping)
wire flash_clk_core, flash_csb_core;
wire flash_clk_oeb_core, flash_csb_oeb_core;
wire flash_clk_ieb_core, flash_csb_ieb_core;
wire flash_io0_oeb_core, flash_io1_oeb_core;
wire flash_io2_oeb_core, flash_io3_oeb_core;
wire flash_io0_ieb_core, flash_io1_ieb_core;
wire flash_io2_ieb_core, flash_io3_ieb_core;
wire flash_io0_do_core, flash_io1_do_core;
wire flash_io2_do_core, flash_io3_do_core;
wire flash_io0_di_core, flash_io1_di_core;
wire flash_io2_di_core, flash_io3_di_core;
// Flash SPI communication (
wire flash_clk_frame;
wire flash_csb_frame;
wire flash_clk_oeb, flash_csb_oeb;
wire flash_clk_ieb, flash_csb_ieb;
wire flash_io0_oeb, flash_io1_oeb;
wire flash_io0_ieb, flash_io1_ieb;
wire flash_io0_do, flash_io1_do;
wire flash_io0_di, flash_io1_di;
chip_io padframe(
`ifndef TOP_ROUTING
// Package Pins
.vddio_pad (vddio), // Common padframe/ESD supply
.vddio_pad2 (vddio_2),
.vssio_pad (vssio), // Common padframe/ESD ground
.vssio_pad2 (vssio_2),
.vccd_pad (vccd), // Common 1.8V supply
.vssd_pad (vssd), // Common digital ground
.vdda_pad (vdda), // Management analog 3.3V supply
.vssa_pad (vssa), // Management analog ground
.vdda1_pad (vdda1), // User area 1 3.3V supply
.vdda1_pad2 (vdda1_2),
.vdda2_pad (vdda2), // User area 2 3.3V supply
.vssa1_pad (vssa1), // User area 1 analog ground
.vssa1_pad2 (vssa1_2),
.vssa2_pad (vssa2), // User area 2 analog ground
.vccd1_pad (vccd1), // User area 1 1.8V supply
.vccd2_pad (vccd2), // User area 2 1.8V supply
.vssd1_pad (vssd1), // User area 1 digital ground
.vssd2_pad (vssd2), // User area 2 digital ground
`endif
// Core Side Pins
.vddio (vddio_core),
.vssio (vssio_core),
.vdda (vdda_core),
.vssa (vssa_core),
.vccd (vccd_core),
.vssd (vssd_core),
.vdda1 (vdda1_core),
.vdda2 (vdda2_core),
.vssa1 (vssa1_core),
.vssa2 (vssa2_core),
.vccd1 (vccd1_core),
.vccd2 (vccd2_core),
.vssd1 (vssd1_core),
.vssd2 (vssd2_core),
.gpio(gpio),
.mprj_io(mprj_io),
.clock(clock),
.resetb(resetb),
.flash_csb(flash_csb),
.flash_clk(flash_clk),
.flash_io0(flash_io0),
.flash_io1(flash_io1),
// SoC Core Interface
.porb_h(porb_h),
.por(por_l),
.resetb_core_h(rstb_h),
.clock_core(clock_core),
.gpio_out_core(gpio_out_core),
.gpio_in_core(gpio_in_core),
.gpio_mode0_core(gpio_mode0_core),
.gpio_mode1_core(gpio_mode1_core),
.gpio_outenb_core(gpio_outenb_core),
.gpio_inenb_core(gpio_inenb_core),
.flash_csb_core(flash_csb_frame),
.flash_clk_core(flash_clk_frame),
.flash_csb_oeb_core(flash_csb_oeb),
.flash_clk_oeb_core(flash_clk_oeb),
.flash_io0_oeb_core(flash_io0_oeb),
.flash_io1_oeb_core(flash_io1_oeb),
.flash_csb_ieb_core(flash_csb_ieb),
.flash_clk_ieb_core(flash_clk_ieb),
.flash_io0_ieb_core(flash_io0_ieb),
.flash_io1_ieb_core(flash_io1_ieb),
.flash_io0_do_core(flash_io0_do),
.flash_io1_do_core(flash_io1_do),
.flash_io0_di_core(flash_io0_di),
.flash_io1_di_core(flash_io1_di),
.mprj_io_in(mprj_io_in),
.mprj_io_out(mprj_io_out),
.mprj_io_oeb(mprj_io_oeb),
.mprj_io_inp_dis(mprj_io_inp_dis),
.mprj_io_ib_mode_sel(mprj_io_ib_mode_sel),
.mprj_io_vtrip_sel(mprj_io_vtrip_sel),
.mprj_io_slow_sel(mprj_io_slow_sel),
.mprj_io_holdover(mprj_io_holdover),
.mprj_io_analog_en(mprj_io_analog_en),
.mprj_io_analog_sel(mprj_io_analog_sel),
.mprj_io_analog_pol(mprj_io_analog_pol),
.mprj_io_dm(mprj_io_dm),
.mprj_analog_io(user_analog_io)
);
// SoC core
wire caravel_clk;
wire caravel_clk2;
wire caravel_rstn;
// Logic analyzer signals
wire [127:0] la_data_in_user; // From CPU to MPRJ
wire [127:0] la_data_in_mprj; // From MPRJ to CPU
wire [127:0] la_data_out_mprj; // From CPU to MPRJ
wire [127:0] la_data_out_user; // From MPRJ to CPU
wire [127:0] la_oenb_user; // From CPU to MPRJ
wire [127:0] la_oenb_mprj; // From CPU to MPRJ
wire [127:0] la_iena_mprj; // From CPU only
wire [2:0] user_irq; // From MRPJ to CPU
wire [2:0] user_irq_core;
wire [2:0] user_irq_ena;
wire [2:0] irq_spi; // From SPI and external pins
// Exported Wishbone Bus (processor facing)
wire mprj_iena_wb;
wire mprj_cyc_o_core;
wire mprj_stb_o_core;
wire mprj_we_o_core;
wire [3:0] mprj_sel_o_core;
wire [31:0] mprj_adr_o_core;
wire [31:0] mprj_dat_o_core;
wire mprj_ack_i_core;
wire [31:0] mprj_dat_i_core;
wire [31:0] hk_dat_i;
wire hk_ack_i;
wire hk_stb_o;
wire hk_cyc_o;
// Exported Wishbone Bus (user area facing)
wire mprj_cyc_o_user;
wire mprj_stb_o_user;
wire mprj_we_o_user;
wire [3:0] mprj_sel_o_user;
wire [31:0] mprj_adr_o_user;
wire [31:0] mprj_dat_o_user;
wire [31:0] mprj_dat_i_user;
wire mprj_ack_i_user;
// Mask revision
wire [31:0] mask_rev;
wire mprj_clock;
wire mprj_clock2;
wire mprj_reset;
// Power monitoring
wire mprj_vcc_pwrgood;
wire mprj2_vcc_pwrgood;
wire mprj_vdd_pwrgood;
wire mprj2_vdd_pwrgood;
// SRAM read-only access from houskeeping
wire hkspi_sram_clk;
wire hkspi_sram_csb;
wire [7:0] hkspi_sram_addr;
wire [31:0] hkspi_sram_data;
// Management processor (wrapper). Any management core
// implementation must match this pinout.
mgmt_core_wrapper soc (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
// Clock and reset
.core_clk(caravel_clk),
.core_rstn(caravel_rstn),
// GPIO (1 pin)
.gpio_out_pad(gpio_out_core),
.gpio_in_pad(gpio_in_core),
.gpio_mode0_pad(gpio_mode0_core),
.gpio_mode1_pad(gpio_mode1_core),
.gpio_outenb_pad(gpio_outenb_core),
.gpio_inenb_pad(gpio_inenb_core),
// Primary SPI flash controller
.flash_csb(flash_csb_core),
.flash_clk(flash_clk_core),
.flash_io0_oeb(flash_io0_oeb_core),
.flash_io0_di(flash_io0_di_core),
.flash_io0_do(flash_io0_do_core),
.flash_io1_oeb(flash_io1_oeb_core),
.flash_io1_di(flash_io1_di_core),
.flash_io1_do(flash_io1_do_core),
.flash_io2_oeb(flash_io2_oeb_core),
.flash_io2_di(flash_io2_di_core),
.flash_io2_do(flash_io2_do_core),
.flash_io3_oeb(flash_io3_oeb_core),
.flash_io3_di(flash_io3_di_core),
.flash_io3_do(flash_io3_do_core),
// Exported Wishbone Bus
.mprj_wb_iena(mprj_iena_wb),
.mprj_cyc_o(mprj_cyc_o_core),
.mprj_stb_o(mprj_stb_o_core),
.mprj_we_o(mprj_we_o_core),
.mprj_sel_o(mprj_sel_o_core),
.mprj_adr_o(mprj_adr_o_core),
.mprj_dat_o(mprj_dat_o_core),
.mprj_ack_i(mprj_ack_i_core),
.mprj_dat_i(mprj_dat_i_core),
.hk_stb_o(hk_stb_o),
.hk_cyc_o(hk_cyc_o),
.hk_dat_i(hk_dat_i),
.hk_ack_i(hk_ack_i),
// IRQ
.irq({irq_spi, user_irq}),
.user_irq_ena(user_irq_ena),
// Module status (these may or may not be implemented)
.qspi_enabled(qspi_enabled),
.uart_enabled(uart_enabled),
.spi_enabled(spi_enabled),
.debug_mode(debug_mode),
// Module I/O (these may or may not be implemented)
// UART
.ser_tx(ser_tx),
.ser_rx(ser_rx),
// SPI master
.spi_sdi(spi_sdi),
.spi_csb(spi_csb),
.spi_sck(spi_sck),
.spi_sdo(spi_sdo),
.spi_sdoenb(spi_sdoenb),
// Debug
.debug_in(debug_in),
.debug_out(debug_out),
.debug_oeb(debug_oeb),
// Logic analyzer
.la_input(la_data_in_mprj),
.la_output(la_data_out_mprj),
.la_oenb(la_oenb_mprj),
.la_iena(la_iena_mprj),
// SRAM Read-only access from housekeeping
.sram_ro_clk(hkspi_sram_clk),
.sram_ro_csb(hkspi_sram_csb),
.sram_ro_addr(hkspi_sram_addr),
.sram_ro_data(hkspi_sram_data),
// Trap status
.trap(trap)
);
/* Clock and reset to user space are passed through a tristate */
/* buffer like the above, but since they are intended to be */
/* always active, connect the enable to the logic-1 output from */
/* the vccd1 domain. */
mgmt_protect mgmt_buffers (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
.vccd2(vccd2_core),
.vssd2(vssd2_core),
.vdda1(vdda1_core),
.vssa1(vssa1_core),
.vdda2(vdda2_core),
.vssa2(vssa2_core),
`endif
.caravel_clk(caravel_clk),
.caravel_clk2(caravel_clk2),
.caravel_rstn(caravel_rstn),
.mprj_iena_wb(mprj_iena_wb),
.mprj_cyc_o_core(mprj_cyc_o_core),
.mprj_stb_o_core(mprj_stb_o_core),
.mprj_we_o_core(mprj_we_o_core),
.mprj_sel_o_core(mprj_sel_o_core),
.mprj_adr_o_core(mprj_adr_o_core),
.mprj_dat_o_core(mprj_dat_o_core),
.mprj_ack_i_core(mprj_ack_i_core),
.mprj_dat_i_core(mprj_dat_i_core),
.user_irq_core(user_irq_core),
.user_irq_ena(user_irq_ena),
.la_data_out_core(la_data_out_user),
.la_data_out_mprj(la_data_out_mprj),
.la_data_in_core(la_data_in_user),
.la_data_in_mprj(la_data_in_mprj),
.la_oenb_mprj(la_oenb_mprj),
.la_oenb_core(la_oenb_user),
.la_iena_mprj(la_iena_mprj),
.user_clock(mprj_clock),
.user_clock2(mprj_clock2),
.user_reset(mprj_reset),
.mprj_cyc_o_user(mprj_cyc_o_user),
.mprj_stb_o_user(mprj_stb_o_user),
.mprj_we_o_user(mprj_we_o_user),
.mprj_sel_o_user(mprj_sel_o_user),
.mprj_adr_o_user(mprj_adr_o_user),
.mprj_dat_o_user(mprj_dat_o_user),
.mprj_dat_i_user(mprj_dat_i_user),
.mprj_ack_i_user(mprj_ack_i_user),
.user_irq(user_irq),
.user1_vcc_powergood(mprj_vcc_pwrgood),
.user2_vcc_powergood(mprj2_vcc_pwrgood),
.user1_vdd_powergood(mprj_vdd_pwrgood),
.user2_vdd_powergood(mprj2_vdd_pwrgood)
);
/*--------------------------------------------------*/
/* Wrapper module around the user project */
/*--------------------------------------------------*/
user_project_wrapper mprj (
`ifdef USE_POWER_PINS
.vdda1(vdda1_core), // User area 1 3.3V power
.vdda2(vdda2_core), // User area 2 3.3V power
.vssa1(vssa1_core), // User area 1 analog ground
.vssa2(vssa2_core), // User area 2 analog ground
.vccd1(vccd1_core), // User area 1 1.8V power
.vccd2(vccd2_core), // User area 2 1.8V power
.vssd1(vssd1_core), // User area 1 digital ground
.vssd2(vssd2_core), // User area 2 digital ground
`endif
.wb_clk_i(mprj_clock),
.wb_rst_i(mprj_reset),
// Management SoC Wishbone bus (exported)
.wbs_cyc_i(mprj_cyc_o_user),
.wbs_stb_i(mprj_stb_o_user),
.wbs_we_i(mprj_we_o_user),
.wbs_sel_i(mprj_sel_o_user),
.wbs_adr_i(mprj_adr_o_user),
.wbs_dat_i(mprj_dat_o_user),
.wbs_ack_o(mprj_ack_i_user),
.wbs_dat_o(mprj_dat_i_user),
// GPIO pad 3-pin interface (plus analog)
.io_in (user_io_in),
.io_out(user_io_out),
.io_oeb(user_io_oeb),
.analog_io(user_analog_io),
// Logic analyzer
.la_data_in(la_data_in_user),
.la_data_out(la_data_out_user),
.la_oenb(la_oenb_user),
// Independent clock
.user_clock2(mprj_clock2),
// IRQ
.user_irq(user_irq_core)
);
/*------------------------------------------*/
/* End user project instantiation */
/*------------------------------------------*/
wire [`MPRJ_IO_PADS_1-1:0] gpio_serial_link_1_shifted;
wire [`MPRJ_IO_PADS_2-1:0] gpio_serial_link_2_shifted;
assign gpio_serial_link_1_shifted = {gpio_serial_link_1[`MPRJ_IO_PADS_1-2:0],
mprj_io_loader_data_1};
// Note that serial_link_2 is backwards compared to serial_link_1, so it
// shifts in the other direction.
assign gpio_serial_link_2_shifted = {mprj_io_loader_data_2,
gpio_serial_link_2[`MPRJ_IO_PADS_2-1:1]};
// Propagating clock and reset to mitigate timing and fanout issues
wire [`MPRJ_IO_PADS_1-1:0] gpio_clock_1;
wire [`MPRJ_IO_PADS_2-1:0] gpio_clock_2;
wire [`MPRJ_IO_PADS_1-1:0] gpio_resetn_1;
wire [`MPRJ_IO_PADS_2-1:0] gpio_resetn_2;
wire [`MPRJ_IO_PADS_1-1:0] gpio_load_1;
wire [`MPRJ_IO_PADS_2-1:0] gpio_load_2;
wire [`MPRJ_IO_PADS_1-1:0] gpio_clock_1_shifted;
wire [`MPRJ_IO_PADS_2-1:0] gpio_clock_2_shifted;
wire [`MPRJ_IO_PADS_1-1:0] gpio_resetn_1_shifted;
wire [`MPRJ_IO_PADS_2-1:0] gpio_resetn_2_shifted;
wire [`MPRJ_IO_PADS_1-1:0] gpio_load_1_shifted;
wire [`MPRJ_IO_PADS_2-1:0] gpio_load_2_shifted;
assign gpio_clock_1_shifted = {gpio_clock_1[`MPRJ_IO_PADS_1-2:0],
mprj_io_loader_clock};
assign gpio_clock_2_shifted = {mprj_io_loader_clock,
gpio_clock_2[`MPRJ_IO_PADS_2-1:1]};
assign gpio_resetn_1_shifted = {gpio_resetn_1[`MPRJ_IO_PADS_1-2:0],
mprj_io_loader_resetn};
assign gpio_resetn_2_shifted = {mprj_io_loader_resetn,
gpio_resetn_2[`MPRJ_IO_PADS_2-1:1]};
assign gpio_load_1_shifted = {gpio_load_1[`MPRJ_IO_PADS_1-2:0],
mprj_io_loader_strobe};
assign gpio_load_2_shifted = {mprj_io_loader_strobe,
gpio_load_2[`MPRJ_IO_PADS_2-1:1]};
wire [2:0] spi_pll_sel;
wire [2:0] spi_pll90_sel;
wire [4:0] spi_pll_div;
wire [25:0] spi_pll_trim;
// Clocking control
caravel_clocking clocking(
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.ext_clk_sel(ext_clk_sel),
.ext_clk(clock_core),
.pll_clk(pll_clk),
.pll_clk90(pll_clk90),
.resetb(rstb_l),
.sel(spi_pll_sel),
.sel2(spi_pll90_sel),
.ext_reset(ext_reset), // From housekeeping SPI
.core_clk(caravel_clk),
.user_clk(caravel_clk2),
.resetb_sync(caravel_rstn)
);
// DCO/Digital Locked Loop
digital_pll pll (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.resetb(rstb_l),
.enable(spi_pll_ena),
.osc(clock_core),
.clockp({pll_clk, pll_clk90}),
.div(spi_pll_div),
.dco(spi_pll_dco_ena),
.ext_trim(spi_pll_trim)
);
// Housekeeping interface
housekeeping housekeeping (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.wb_clk_i(caravel_clk),
.wb_rstn_i(caravel_rstn),
.wb_adr_i(mprj_adr_o_core),
.wb_dat_i(mprj_dat_o_core),
.wb_sel_i(mprj_sel_o_core),
.wb_we_i(mprj_we_o_core),
.wb_cyc_i(hk_cyc_o),
.wb_stb_i(hk_stb_o),
.wb_ack_o(hk_ack_i),
.wb_dat_o(hk_dat_i),
.porb(porb_l),
.pll_ena(spi_pll_ena),
.pll_dco_ena(spi_pll_dco_ena),
.pll_div(spi_pll_div),
.pll_sel(spi_pll_sel),
.pll90_sel(spi_pll90_sel),
.pll_trim(spi_pll_trim),
.pll_bypass(ext_clk_sel),
.qspi_enabled(qspi_enabled),
.uart_enabled(uart_enabled),
.spi_enabled(spi_enabled),
.debug_mode(debug_mode),
.ser_tx(ser_tx),
.ser_rx(ser_rx),
.spi_sdi(spi_sdi),
.spi_csb(spi_csb),
.spi_sck(spi_sck),
.spi_sdo(spi_sdo),
.spi_sdoenb(spi_sdoenb),
.debug_in(debug_in),
.debug_out(debug_out),
.debug_oeb(debug_oeb),
.irq(irq_spi),
.reset(ext_reset),
.serial_clock(mprj_io_loader_clock),
.serial_load(mprj_io_loader_strobe),
.serial_resetn(mprj_io_loader_resetn),
.serial_data_1(mprj_io_loader_data_1),
.serial_data_2(mprj_io_loader_data_2),
.mgmt_gpio_in(mgmt_io_in),
.mgmt_gpio_out({mgmt_io_out[4:2], mgmt_io_in[`MPRJ_IO_PADS-4:2],
mgmt_io_out[1:0]}),
.mgmt_gpio_oeb({mgmt_io_oeb[4:2], mgmt_io_nc[`MPRJ_IO_PADS-6:0],
mgmt_io_oeb[1:0]}),
.pwr_ctrl_out(pwr_ctrl_nc), /* Not used in this version */
.trap(trap),
.user_clock(caravel_clk2),
.mask_rev_in(mask_rev),
.spimemio_flash_csb(flash_csb_core),
.spimemio_flash_clk(flash_clk_core),
.spimemio_flash_io0_oeb(flash_io0_oeb_core),
.spimemio_flash_io1_oeb(flash_io1_oeb_core),
.spimemio_flash_io2_oeb(flash_io2_oeb_core),
.spimemio_flash_io3_oeb(flash_io3_oeb_core),
.spimemio_flash_io0_do(flash_io0_do_core),
.spimemio_flash_io1_do(flash_io1_do_core),
.spimemio_flash_io2_do(flash_io2_do_core),
.spimemio_flash_io3_do(flash_io3_do_core),
.spimemio_flash_io0_di(flash_io0_di_core),
.spimemio_flash_io1_di(flash_io1_di_core),
.spimemio_flash_io2_di(flash_io2_di_core),
.spimemio_flash_io3_di(flash_io3_di_core),
.pad_flash_csb(flash_csb_frame),
.pad_flash_csb_oeb(flash_csb_oeb),
.pad_flash_clk(flash_clk_frame),
.pad_flash_clk_oeb(flash_clk_oeb),
.pad_flash_io0_oeb(flash_io0_oeb),
.pad_flash_io1_oeb(flash_io1_oeb),
.pad_flash_io0_ieb(flash_io0_ieb),
.pad_flash_io1_ieb(flash_io1_ieb),
.pad_flash_io0_do(flash_io0_do),
.pad_flash_io1_do(flash_io1_do),
.pad_flash_io0_di(flash_io0_di),
.pad_flash_io1_di(flash_io1_di),
.sram_ro_clk(hkspi_sram_clk),
.sram_ro_csb(hkspi_sram_csb),
.sram_ro_addr(hkspi_sram_addr),
.sram_ro_data(hkspi_sram_data),
.usr1_vcc_pwrgood(mprj_vcc_pwrgood),
.usr2_vcc_pwrgood(mprj2_vcc_pwrgood),
.usr1_vdd_pwrgood(mprj_vdd_pwrgood),
.usr2_vdd_pwrgood(mprj2_vdd_pwrgood)
);
/* GPIO defaults (via programmed) */
wire [`MPRJ_IO_PADS*13-1:0] gpio_defaults;
/* Fixed defaults for the first 5 GPIO pins */
gpio_defaults_block #(
.GPIO_CONFIG_INIT(13'h1803)
) gpio_defaults_block_0 [1:0] (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[25:0])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(13'h0403)
) gpio_defaults_block_2 [2:0] (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[64:26])
);
/* Via-programmable defaults for the rest of the GPIO pins */
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_5_INIT)
) gpio_defaults_block_5 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[77:65])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_6_INIT)
) gpio_defaults_block_6 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[90:78])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_7_INIT)
) gpio_defaults_block_7 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[103:91])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_8_INIT)
) gpio_defaults_block_8 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[116:104])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_9_INIT)
) gpio_defaults_block_9 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[129:117])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_10_INIT)
) gpio_defaults_block_10 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[142:130])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_11_INIT)
) gpio_defaults_block_11 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[155:143])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_12_INIT)
) gpio_defaults_block_12 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[168:156])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_13_INIT)
) gpio_defaults_block_13 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[181:169])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_14_INIT)
) gpio_defaults_block_14 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[194:182])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_15_INIT)
) gpio_defaults_block_15 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[207:195])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_16_INIT)
) gpio_defaults_block_16 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[220:208])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_17_INIT)
) gpio_defaults_block_17 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[233:221])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_18_INIT)
) gpio_defaults_block_18 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[246:234])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_19_INIT)
) gpio_defaults_block_19 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[259:247])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_20_INIT)
) gpio_defaults_block_20 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[272:260])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_21_INIT)
) gpio_defaults_block_21 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[285:273])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_22_INIT)
) gpio_defaults_block_22 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[298:286])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_23_INIT)
) gpio_defaults_block_23 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[311:299])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_24_INIT)
) gpio_defaults_block_24 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[324:312])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_25_INIT)
) gpio_defaults_block_25 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[337:325])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_26_INIT)
) gpio_defaults_block_26 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[350:338])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_27_INIT)
) gpio_defaults_block_27 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[363:351])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_28_INIT)
) gpio_defaults_block_28 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[376:364])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_29_INIT)
) gpio_defaults_block_29 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[389:377])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_30_INIT)
) gpio_defaults_block_30 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[402:390])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_31_INIT)
) gpio_defaults_block_31 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[415:403])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_32_INIT)
) gpio_defaults_block_32 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[428:416])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_33_INIT)
) gpio_defaults_block_33 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[441:429])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_34_INIT)
) gpio_defaults_block_34 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[454:442])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_35_INIT)
) gpio_defaults_block_35 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[467:455])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_36_INIT)
) gpio_defaults_block_36 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[480:468])
);
gpio_defaults_block #(
.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_37_INIT)
) gpio_defaults_block_37 (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.gpio_defaults(gpio_defaults[493:481])
);
// Each control block sits next to an I/O pad in the user area.
// It gets input through a serial chain from the previous control
// block and passes it to the next control block. Due to the nature
// of the shift register, bits are presented in reverse, as the first
// bit in ends up as the last bit of the last I/O pad control block.
// There are two types of block; the first two and the last two
// are configured to be full bidirectional under control of the
// management Soc (JTAG and SDO for the first two; flash_io2 and
// flash_io3 for the last two). The rest are configured to be default
// (input). Note that the first two and last two are the ones closest
// to the management SoC on either side, which minimizes the wire length
// of the extra signals those pads need.
/* First two GPIOs (JTAG and SDO) */
gpio_control_block gpio_control_bidir_1 [1:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
`endif
.gpio_defaults(gpio_defaults[25:0]),
// Management Soc-facing signals
.resetn(gpio_resetn_1_shifted[1:0]),
.serial_clock(gpio_clock_1_shifted[1:0]),
.serial_load(gpio_load_1_shifted[1:0]),
.resetn_out(gpio_resetn_1[1:0]),
.serial_clock_out(gpio_clock_1[1:0]),
.serial_load_out(gpio_load_1[1:0]),
.mgmt_gpio_in(mgmt_io_in[1:0]),
.mgmt_gpio_out(mgmt_io_out[1:0]),
.mgmt_gpio_oeb(mgmt_io_oeb[1:0]),
.one(),
.zero(),
// Serial data chain for pad configuration
.serial_data_in(gpio_serial_link_1_shifted[1:0]),
.serial_data_out(gpio_serial_link_1[1:0]),
// User-facing signals
.user_gpio_out(user_io_out[1:0]),
.user_gpio_oeb(user_io_oeb[1:0]),
.user_gpio_in(user_io_in[1:0]),
// Pad-facing signals (Pad GPIOv2)
.pad_gpio_inenb(mprj_io_inp_dis[1:0]),
.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[1:0]),
.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[1:0]),
.pad_gpio_slow_sel(mprj_io_slow_sel[1:0]),
.pad_gpio_holdover(mprj_io_holdover[1:0]),
.pad_gpio_ana_en(mprj_io_analog_en[1:0]),
.pad_gpio_ana_sel(mprj_io_analog_sel[1:0]),
.pad_gpio_ana_pol(mprj_io_analog_pol[1:0]),
.pad_gpio_dm(mprj_io_dm[5:0]),
.pad_gpio_outenb(mprj_io_oeb[1:0]),
.pad_gpio_out(mprj_io_out[1:0]),
.pad_gpio_in(mprj_io_in[1:0])
);
/* Section 1 GPIOs (GPIO 0 to 18) */
wire [`MPRJ_IO_PADS_1-1:2] one_loop1;
/* Section 1 GPIOs (GPIO 2 to 7) that start up under management control */
gpio_control_block gpio_control_in_1a [5:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
`endif
.gpio_defaults(gpio_defaults[103:26]),
// Management Soc-facing signals
.resetn(gpio_resetn_1_shifted[7:2]),
.serial_clock(gpio_clock_1_shifted[7:2]),
.serial_load(gpio_load_1_shifted[7:2]),
.resetn_out(gpio_resetn_1[7:2]),
.serial_clock_out(gpio_clock_1[7:2]),
.serial_load_out(gpio_load_1[7:2]),
.mgmt_gpio_in(mgmt_io_in[7:2]),
.mgmt_gpio_out(mgmt_io_in[7:2]),
.mgmt_gpio_oeb(one_loop1[7:2]),
.one(one_loop1[7:2]),
.zero(),
// Serial data chain for pad configuration
.serial_data_in(gpio_serial_link_1_shifted[7:2]),
.serial_data_out(gpio_serial_link_1[7:2]),
// User-facing signals
.user_gpio_out(user_io_out[7:2]),
.user_gpio_oeb(user_io_oeb[7:2]),
.user_gpio_in(user_io_in[7:2]),
// Pad-facing signals (Pad GPIOv2)
.pad_gpio_inenb(mprj_io_inp_dis[7:2]),
.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[7:2]),
.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[7:2]),
.pad_gpio_slow_sel(mprj_io_slow_sel[7:2]),
.pad_gpio_holdover(mprj_io_holdover[7:2]),
.pad_gpio_ana_en(mprj_io_analog_en[7:2]),
.pad_gpio_ana_sel(mprj_io_analog_sel[7:2]),
.pad_gpio_ana_pol(mprj_io_analog_pol[7:2]),
.pad_gpio_dm(mprj_io_dm[23:6]),
.pad_gpio_outenb(mprj_io_oeb[7:2]),
.pad_gpio_out(mprj_io_out[7:2]),
.pad_gpio_in(mprj_io_in[7:2])
);
/* Section 1 GPIOs (GPIO 8 to 18) */
gpio_control_block gpio_control_in_1 [`MPRJ_IO_PADS_1-9:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
`endif
.gpio_defaults(gpio_defaults[(`MPRJ_IO_PADS_1*13-1):104]),
// Management Soc-facing signals
.resetn(gpio_resetn_1_shifted[(`MPRJ_IO_PADS_1-1):8]),
.serial_clock(gpio_clock_1_shifted[(`MPRJ_IO_PADS_1-1):8]),
.serial_load(gpio_load_1_shifted[(`MPRJ_IO_PADS_1-1):8]),
.resetn_out(gpio_resetn_1[(`MPRJ_IO_PADS_1-1):8]),
.serial_clock_out(gpio_clock_1[(`MPRJ_IO_PADS_1-1):8]),
.serial_load_out(gpio_load_1[(`MPRJ_IO_PADS_1-1):8]),
.mgmt_gpio_in(mgmt_io_in[(`MPRJ_IO_PADS_1-1):8]),
.mgmt_gpio_out(mgmt_io_in[(`MPRJ_IO_PADS_1-1):8]),
.mgmt_gpio_oeb(one_loop1[(`MPRJ_IO_PADS_1-1):8]),
.one(one_loop1[(`MPRJ_IO_PADS_1-1):8]),
.zero(),
// Serial data chain for pad configuration
.serial_data_in(gpio_serial_link_1_shifted[(`MPRJ_IO_PADS_1-1):8]),
.serial_data_out(gpio_serial_link_1[(`MPRJ_IO_PADS_1-1):8]),
// User-facing signals
.user_gpio_out(user_io_out[(`MPRJ_IO_PADS_1-1):8]),
.user_gpio_oeb(user_io_oeb[(`MPRJ_IO_PADS_1-1):8]),
.user_gpio_in(user_io_in[(`MPRJ_IO_PADS_1-1):8]),
// Pad-facing signals (Pad GPIOv2)
.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_dm(mprj_io_dm[(`MPRJ_IO_PADS_1*3-1):24]),
.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_out(mprj_io_out[(`MPRJ_IO_PADS_1-1):8]),
.pad_gpio_in(mprj_io_in[(`MPRJ_IO_PADS_1-1):8])
);
/* Last three GPIOs (spi_sdo, flash_io2, and flash_io3) */
gpio_control_block gpio_control_bidir_2 [2:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
`endif
.gpio_defaults(gpio_defaults[(`MPRJ_IO_PADS*13-1):(`MPRJ_IO_PADS*13-39)]),
// Management Soc-facing signals
.resetn(gpio_resetn_2_shifted[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.serial_clock(gpio_clock_2_shifted[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.serial_load(gpio_load_2_shifted[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.resetn_out(gpio_resetn_2[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.serial_clock_out(gpio_clock_2[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.serial_load_out(gpio_load_2[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.mgmt_gpio_in(mgmt_io_in[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.mgmt_gpio_out(mgmt_io_out[4:2]),
.mgmt_gpio_oeb(mgmt_io_oeb[4:2]),
.one(),
.zero(),
// Serial data chain for pad configuration
.serial_data_in(gpio_serial_link_2_shifted[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
.serial_data_out(gpio_serial_link_2[(`MPRJ_IO_PADS_2-1):(`MPRJ_IO_PADS_2-3)]),
// User-facing signals
.user_gpio_out(user_io_out[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.user_gpio_oeb(user_io_oeb[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.user_gpio_in(user_io_in[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
// Pad-facing signals (Pad GPIOv2)
.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_dm(mprj_io_dm[(`MPRJ_IO_PADS*3-1):(`MPRJ_IO_PADS*3-9)]),
.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_out(mprj_io_out[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)]),
.pad_gpio_in(mprj_io_in[(`MPRJ_IO_PADS-1):(`MPRJ_IO_PADS-3)])
);
/* Section 2 GPIOs (GPIO 19 to 34) */
wire [`MPRJ_IO_PADS_2-4:0] one_loop2;
gpio_control_block gpio_control_in_2 [`MPRJ_IO_PADS_2-4:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
.vccd1(vccd1_core),
.vssd1(vssd1_core),
`endif
.gpio_defaults(gpio_defaults[(`MPRJ_IO_PADS*13-40):(`MPRJ_IO_PADS_1*13)]),
// Management Soc-facing signals
.resetn(gpio_resetn_2_shifted[(`MPRJ_IO_PADS_2-4):0]),
.serial_clock(gpio_clock_2_shifted[(`MPRJ_IO_PADS_2-4):0]),
.serial_load(gpio_load_2_shifted[(`MPRJ_IO_PADS_2-4):0]),
.resetn_out(gpio_resetn_2[(`MPRJ_IO_PADS_2-4):0]),
.serial_clock_out(gpio_clock_2[(`MPRJ_IO_PADS_2-4):0]),
.serial_load_out(gpio_load_2[(`MPRJ_IO_PADS_2-4):0]),
.mgmt_gpio_in(mgmt_io_in[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.mgmt_gpio_out(mgmt_io_in[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.mgmt_gpio_oeb(one_loop2),
.one(one_loop2),
.zero(),
// Serial data chain for pad configuration
.serial_data_in(gpio_serial_link_2_shifted[(`MPRJ_IO_PADS_2-4):0]),
.serial_data_out(gpio_serial_link_2[(`MPRJ_IO_PADS_2-4):0]),
// User-facing signals
.user_gpio_out(user_io_out[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.user_gpio_oeb(user_io_oeb[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.user_gpio_in(user_io_in[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
// Pad-facing signals (Pad GPIOv2)
.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_dm(mprj_io_dm[(`MPRJ_IO_PADS*3-10):(`MPRJ_IO_PADS_1*3)]),
.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_out(mprj_io_out[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)]),
.pad_gpio_in(mprj_io_in[(`MPRJ_IO_PADS-4):(`MPRJ_IO_PADS_1)])
);
user_id_programming #(
.USER_PROJECT_ID(USER_PROJECT_ID)
) user_id_value (
`ifdef USE_POWER_PINS
.VPWR(vccd_core),
.VGND(vssd_core),
`endif
.mask_rev(mask_rev)
);
// Power-on-reset circuit
simple_por por (
`ifdef USE_POWER_PINS
.vdd3v3(vddio_core),
.vdd1v8(vccd_core),
.vss3v3(vssio_core),
.vss1v8(vssd_core),
`endif
.porb_h(porb_h),
.porb_l(porb_l),
.por_l(por_l)
);
// XRES (chip input pin reset) reset level converter
xres_buf rstb_level (
`ifdef USE_POWER_PINS
.VPWR(vddio_core),
.LVPWR(vccd_core),
.LVGND(vssd_core),
.VGND(vssio_core),
`endif
.A(rstb_h),
.X(rstb_l)
);
// Spare logic for metal mask fixes
wire [107:0] spare_xz_nc;
wire [15:0] spare_xi_nc;
wire [3:0] spare_xib_nc;
wire [7:0] spare_xna_nc;
wire [7:0] spare_xno_nc;
wire [7:0] spare_xmx_nc;
wire [7:0] spare_xfq_nc;
wire [7:0] spare_xfqn_nc;
spare_logic_block spare_logic [3:0] (
`ifdef USE_POWER_PINS
.vccd(vccd_core),
.vssd(vssd_core),
`endif
.spare_xz(spare_xz_nc),
.spare_xi(spare_xi_nc),
.spare_xib(spare_xib_nc),
.spare_xna(spare_xna_nc),
.spare_xno(spare_xno_nc),
.spare_xmx(spare_xmx_nc),
.spare_xfq(spare_xfq_nc),
.spare_xfqn(spare_xfqn_nc)
);
endmodule
// `default_nettype wire