blob: 066fdae7f1edd1f16f1abb06842e797dcdff0f63 [file] [log] [blame]
/*
* SPDX-FileCopyrightText: 2020 Efabless Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
* SPDX-License-Identifier: Apache-2.0
*/
// This include is relative to $CARAVEL_PATH (see Makefile)
#include <defs.h>
#include <stub.c>
/*
IO Test:
- Configures MPRJ lower 8-IO pins as outputs
- Observes counter value through the MPRJ lower 8 IO pins (in the testbench)
*/
void main()
{
/*
IO Control Registers
| DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
| 3-bits | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit | 1-bit |
Output: 0000_0110_0000_1110 (0x1808) = GPIO_MODE_USER_STD_OUTPUT
| DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
| 110 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 |
Input: 0000_0001_0000_1111 (0x0402) = GPIO_MODE_USER_STD_INPUT_NOPULL
| DM | VTRIP | SLOW | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
| 001 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 |
*/
/* Set up the housekeeping SPI to be connected internally so */
/* that external pin changes don't affect it. */
// reg_spi_enable = 1;
// reg_spimaster_cs = 0x10001;
// reg_spimaster_control = 0x0801;
// reg_spimaster_control = 0xa002; // Enable, prescaler = 2,
// connect to housekeeping SPI
// Connect the housekeeping SPI to the SPI master
// so that the CSB line is not left floating. This allows
// all of the GPIO pins to be used for user functions.
// Configure lower 8-IOs as user output
// Observe counter value in the testbench
//#define GPIO_MODE_USER_STD_OUTPUT 0x1808
// reg_mprj_io_0 = GPIO_MODE_USER_STD_OUTPUT;
// reg_mprj_io_1 = GPIO_MODE_USER_STD_OUTPUT;
// reg_mprj_io_2 = GPIO_MODE_USER_STD_OUTPUT;
// reg_mprj_io_3 = GPIO_MODE_USER_STD_OUTPUT;
// reg_mprj_io_4 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_5 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_6 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_7 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_8 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_9 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_10 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_11 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_12 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_13 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_14 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_15 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_16 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_17 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_18 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_19 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_20 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_21 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_22 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_23 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_24 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_25 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_26 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_27 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_28 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_29 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_30 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_31 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_32 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_33 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_34 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_35 = GPIO_MODE_USER_STD_INPUT_NOPULL;
reg_mprj_io_36 = GPIO_MODE_USER_STD_OUTPUT;
reg_mprj_io_37 = GPIO_MODE_USER_STD_OUTPUT;
/* Apply configuration */
reg_mprj_xfer = 1;
while (reg_mprj_xfer == 1);
}