| ////////////////////////////////////////////////////////////////////////////// |
| // SPDX-FileCopyrightText: 2012 Micron Technology, Inc. |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| // SPDX-FileContributor: Created by Dinesh Annayya <dinesha@opencores.org> |
| // |
| |
| /**************************************************************************************** |
| * |
| * File Name: MT48LC8M8A2.V |
| * Version: 0.0f |
| * Date: July 8th, 1999 |
| * Model: BUS Functional |
| * Simulator: Model Technology (PC version 5.2e PE) |
| * |
| * Dependencies: None |
| * |
| * Author: Son P. Huynh |
| * Email: sphuynh@micron.com |
| * Phone: (208) 368-3825 |
| * Company: Micron Technology, Inc. |
| * Model: MT48LC8M16A2 (2Meg x 8 x 4 Banks) |
| * |
| * Description: Micron 128Mb SDRAM Verilog model |
| * |
| * Limitation: - Doesn't check for 4096 cycle refresh |
| * |
| * Note: - Set simulator resolution to "ps" accuracy |
| * - Set Debug = 0 to disable $display messages |
| * |
| * Disclaimer: THESE DESIGNS ARE PROVIDED "AS IS" WITH NO WARRANTY |
| * WHATSOEVER AND MICRON SPECIFICALLY DISCLAIMS ANY |
| * IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR |
| * A PARTICULAR PURPOSE, OR AGAINST INFRINGEMENT. |
| * |
| * Copyright © 1998 Micron Semiconductor Products, Inc. |
| * All rights researved |
| * |
| * Rev Author Phone Date Changes |
| * ---- ---------------------------- ---------- --------------------------------------- |
| * 0.0f Son Huynh 208-368-3825 07/08/1999 - Fix tWR = 1 Clk + 7.5 ns (Auto) |
| * Micron Technology Inc. - Fix tWR = 15 ns (Manual) |
| * - Fix tRP (Autoprecharge to AutoRefresh) |
| * |
| * 0.0a Son Huynh 208-368-3825 05/13/1998 - First Release (from 64Mb rev 0.0e) |
| * Micron Technology Inc. |
| ****************************************************************************************/ |
| |
| `timescale 1ns / 100ps |
| |
| module mt48lc8m8a2 (Dq, Addr, Ba, Clk, Cke, Cs_n, Ras_n, Cas_n, We_n, Dqm); |
| |
| parameter addr_bits = 12; |
| parameter data_bits = 8; |
| parameter col_bits = 9; |
| parameter mem_sizes = 2097151; // 2 Meg |
| |
| inout [data_bits - 1 : 0] Dq; |
| input [addr_bits - 1 : 0] Addr; |
| input [1 : 0] Ba; |
| input Clk; |
| input Cke; |
| input Cs_n; |
| input Ras_n; |
| input Cas_n; |
| input We_n; |
| input [0 : 0] Dqm; |
| |
| reg [data_bits - 1 : 0] Bank0 [0 : mem_sizes]; |
| reg [data_bits - 1 : 0] Bank1 [0 : mem_sizes]; |
| reg [data_bits - 1 : 0] Bank2 [0 : mem_sizes]; |
| reg [data_bits - 1 : 0] Bank3 [0 : mem_sizes]; |
| |
| reg [1 : 0] Bank_addr [0 : 3]; // Bank Address Pipeline |
| reg [col_bits - 1 : 0] Col_addr [0 : 3]; // Column Address Pipeline |
| reg [3 : 0] Command [0 : 3]; // Command Operation Pipeline |
| reg [0 : 0] Dqm_reg0, Dqm_reg1; // DQM Operation Pipeline |
| reg [addr_bits - 1 : 0] B0_row_addr, B1_row_addr, B2_row_addr, B3_row_addr; |
| |
| reg [addr_bits - 1 : 0] Mode_reg; |
| reg [data_bits - 1 : 0] Dq_reg, Dq_dqm; |
| reg [col_bits - 1 : 0] Col_temp, Burst_counter; |
| |
| reg Act_b0, Act_b1, Act_b2, Act_b3; // Bank Activate |
| reg Pc_b0, Pc_b1, Pc_b2, Pc_b3; // Bank Precharge |
| |
| reg [1 : 0] Bank_precharge [0 : 3]; // Precharge Command |
| reg A10_precharge [0 : 3]; // Addr[10] = 1 (All banks) |
| reg Auto_precharge [0 : 3]; // RW AutoPrecharge (Bank) |
| reg Read_precharge [0 : 3]; // R AutoPrecharge |
| reg Write_precharge [0 : 3]; // W AutoPrecharge |
| integer Count_precharge [0 : 3]; // RW AutoPrecharge (Counter) |
| reg RW_interrupt_read [0 : 3]; // RW Interrupt Read with Auto Precharge |
| reg RW_interrupt_write [0 : 3]; // RW Interrupt Write with Auto Precharge |
| |
| reg Data_in_enable; |
| reg Data_out_enable; |
| |
| reg [1 : 0] Bank, Previous_bank; |
| reg [addr_bits - 1 : 0] Row; |
| reg [col_bits - 1 : 0] Col, Col_brst; |
| |
| // Internal system clock |
| reg CkeZ, Sys_clk; |
| |
| event error_detected; |
| |
| // Commands Decode |
| wire Active_enable = ~Cs_n & ~Ras_n & Cas_n & We_n; |
| wire Aref_enable = ~Cs_n & ~Ras_n & ~Cas_n & We_n; |
| wire Burst_term = ~Cs_n & Ras_n & Cas_n & ~We_n; |
| wire Mode_reg_enable = ~Cs_n & ~Ras_n & ~Cas_n & ~We_n; |
| wire Prech_enable = ~Cs_n & ~Ras_n & Cas_n & ~We_n; |
| wire Read_enable = ~Cs_n & Ras_n & ~Cas_n & We_n; |
| wire Write_enable = ~Cs_n & Ras_n & ~Cas_n & ~We_n; |
| |
| // Burst Length Decode |
| wire Burst_length_1 = ~Mode_reg[2] & ~Mode_reg[1] & ~Mode_reg[0]; |
| wire Burst_length_2 = ~Mode_reg[2] & ~Mode_reg[1] & Mode_reg[0]; |
| wire Burst_length_4 = ~Mode_reg[2] & Mode_reg[1] & ~Mode_reg[0]; |
| wire Burst_length_8 = ~Mode_reg[2] & Mode_reg[1] & Mode_reg[0]; |
| |
| // CAS Latency Decode |
| wire Cas_latency_2 = ~Mode_reg[6] & Mode_reg[5] & ~Mode_reg[4]; |
| wire Cas_latency_3 = ~Mode_reg[6] & Mode_reg[5] & Mode_reg[4]; |
| |
| `ifdef VERBOSE |
| wire Debug = 1'b1; // Debug messages : 1 = On |
| `else |
| wire Debug = 1'b0; // Debug messages : 1 = On |
| `endif |
| // Write Burst Mode |
| wire Write_burst_mode = Mode_reg[9]; |
| |
| wire Dq_chk = Sys_clk & Data_in_enable; // Check setup/hold time for DQ |
| |
| assign Dq = Dq_reg; // DQ buffer |
| |
| // Commands Operation |
| `define ACT 0 |
| `define NOP 1 |
| `define READ 2 |
| `define READ_A 3 |
| `define SDRAM_WRITE 4 |
| `define WRITE_A 5 |
| `define SDRAM_PRECH 6 |
| `define SDRAM_A_REF 7 |
| `define SDRAM_BST 8 |
| `define SDRAM_LMR 9 |
| |
| // Timing Parameters for -75 (PC133) and CAS Latency = 2 |
| parameter tAC = 6.0; |
| parameter tHZ = 7.0; |
| parameter tOH = 2.7; |
| parameter tMRD = 2.0; // 2 Clk Cycles |
| parameter tRAS = 44.0; |
| parameter tRC = 66.0; |
| parameter tRCD = 20.0; |
| parameter tRP = 20.0; |
| parameter tRRD = 15.0; |
| parameter tWRa = 7.5; // A2 Version - Auto precharge mode only (1 Clk + 7.5 ns) |
| parameter tWRp = 15.0; // A2 Version - Precharge mode only (15 ns) |
| |
| // Timing Check variable |
| integer MRD_chk; |
| integer WR_counter [0 : 3]; |
| time WR_chk [0 : 3]; |
| time RC_chk, RRD_chk; |
| time RAS_chk0, RAS_chk1, RAS_chk2, RAS_chk3; |
| time RCD_chk0, RCD_chk1, RCD_chk2, RCD_chk3; |
| time RP_chk0, RP_chk1, RP_chk2, RP_chk3; |
| |
| initial begin |
| |
| Dq_reg = {data_bits{1'bz}}; |
| {Data_in_enable, Data_out_enable} = 0; |
| {Act_b0, Act_b1, Act_b2, Act_b3} = 4'b0000; |
| {Pc_b0, Pc_b1, Pc_b2, Pc_b3} = 4'b0000; |
| {WR_chk[0], WR_chk[1], WR_chk[2], WR_chk[3]} = 0; |
| {WR_counter[0], WR_counter[1], WR_counter[2], WR_counter[3]} = 0; |
| {RW_interrupt_read[0], RW_interrupt_read[1], RW_interrupt_read[2], RW_interrupt_read[3]} = 0; |
| {RW_interrupt_write[0], RW_interrupt_write[1], RW_interrupt_write[2], RW_interrupt_write[3]} = 0; |
| {MRD_chk, RC_chk, RRD_chk} = 0; |
| {RAS_chk0, RAS_chk1, RAS_chk2, RAS_chk3} = 0; |
| {RCD_chk0, RCD_chk1, RCD_chk2, RCD_chk3} = 0; |
| {RP_chk0, RP_chk1, RP_chk2, RP_chk3} = 0; |
| $timeformat (-9, 0, " ns", 12); |
| //$readmemh("bank0.txt", Bank0); |
| //$readmemh("bank1.txt", Bank1); |
| //$readmemh("bank2.txt", Bank2); |
| //$readmemh("bank3.txt", Bank3); |
| end |
| |
| // System clock generator |
| always begin |
| @ (posedge Clk) begin |
| Sys_clk = CkeZ; |
| CkeZ = Cke; |
| end |
| @ (negedge Clk) begin |
| Sys_clk = 1'b0; |
| end |
| end |
| |
| always @ (posedge Sys_clk) begin |
| // Internal Commamd Pipelined |
| Command[0] = Command[1]; |
| Command[1] = Command[2]; |
| Command[2] = Command[3]; |
| Command[3] = `NOP; |
| |
| Col_addr[0] = Col_addr[1]; |
| Col_addr[1] = Col_addr[2]; |
| Col_addr[2] = Col_addr[3]; |
| Col_addr[3] = {col_bits{1'b0}}; |
| |
| Bank_addr[0] = Bank_addr[1]; |
| Bank_addr[1] = Bank_addr[2]; |
| Bank_addr[2] = Bank_addr[3]; |
| Bank_addr[3] = 2'b0; |
| |
| Bank_precharge[0] = Bank_precharge[1]; |
| Bank_precharge[1] = Bank_precharge[2]; |
| Bank_precharge[2] = Bank_precharge[3]; |
| Bank_precharge[3] = 2'b0; |
| |
| A10_precharge[0] = A10_precharge[1]; |
| A10_precharge[1] = A10_precharge[2]; |
| A10_precharge[2] = A10_precharge[3]; |
| A10_precharge[3] = 1'b0; |
| |
| // Dqm pipeline for Read |
| Dqm_reg0 = Dqm_reg1; |
| Dqm_reg1 = Dqm; |
| |
| // Read or Write with Auto Precharge Counter |
| if (Auto_precharge[0] == 1'b1) begin |
| Count_precharge[0] = Count_precharge[0] + 1; |
| end |
| if (Auto_precharge[1] == 1'b1) begin |
| Count_precharge[1] = Count_precharge[1] + 1; |
| end |
| if (Auto_precharge[2] == 1'b1) begin |
| Count_precharge[2] = Count_precharge[2] + 1; |
| end |
| if (Auto_precharge[3] == 1'b1) begin |
| Count_precharge[3] = Count_precharge[3] + 1; |
| end |
| |
| // tMRD Counter |
| MRD_chk = MRD_chk + 1; |
| |
| // tWR Counter for Write |
| WR_counter[0] = WR_counter[0] + 1; |
| WR_counter[1] = WR_counter[1] + 1; |
| WR_counter[2] = WR_counter[2] + 1; |
| WR_counter[3] = WR_counter[3] + 1; |
| |
| // Auto Refresh |
| if (Aref_enable == 1'b1) begin |
| if (Debug) $display ("at time %t AREF : Auto Refresh", $time); |
| // Auto Refresh to Auto Refresh |
| if ($time - RC_chk < tRC) begin |
| ->error_detected; |
| $display ("at time %t ERROR: tRC violation during Auto Refresh", $time); |
| end |
| // Precharge to Auto Refresh |
| if ($time - RP_chk0 < tRP || $time - RP_chk1 < tRP || $time - RP_chk2 < tRP || $time - RP_chk3 < tRP) begin |
| ->error_detected; |
| $display ("at time %t ERROR: tRP violation during Auto Refresh", $time); |
| end |
| // Precharge to Refresh |
| if (Pc_b0 == 1'b0 || Pc_b1 == 1'b0 || Pc_b2 == 1'b0 || Pc_b3 == 1'b0) begin |
| ->error_detected; |
| $display ("at time %t ERROR: All banks must be Precharge before Auto Refresh", $time); |
| end |
| // Record Current tRC time |
| RC_chk = $time; |
| end |
| |
| // Load Mode Register |
| if (Mode_reg_enable == 1'b1) begin |
| // Decode CAS Latency, Burst Length, Burst Type, and Write Burst Mode |
| if (Pc_b0 == 1'b1 && Pc_b1 == 1'b1 && Pc_b2 == 1'b1 && Pc_b3 == 1'b1) begin |
| Mode_reg = Addr; |
| if (Debug) begin |
| $display ("at time %t LMR : Load Mode Register", $time); |
| // CAS Latency |
| if (Addr[6 : 4] == 3'b010) |
| $display (" CAS Latency = 2"); |
| else if (Addr[6 : 4] == 3'b011) |
| $display (" CAS Latency = 3"); |
| else |
| $display (" CAS Latency = Reserved"); |
| // Burst Length |
| if (Addr[2 : 0] == 3'b000) |
| $display (" Burst Length = 1"); |
| else if (Addr[2 : 0] == 3'b001) |
| $display (" Burst Length = 2"); |
| else if (Addr[2 : 0] == 3'b010) |
| $display (" Burst Length = 4"); |
| else if (Addr[2 : 0] == 3'b011) |
| $display (" Burst Length = 8"); |
| else if (Addr[3 : 0] == 4'b0111) |
| $display (" Burst Length = Full"); |
| else |
| $display (" Burst Length = Reserved"); |
| // Burst Type |
| if (Addr[3] == 1'b0) |
| $display (" Burst Type = Sequential"); |
| else if (Addr[3] == 1'b1) |
| $display (" Burst Type = Interleaved"); |
| else |
| $display (" Burst Type = Reserved"); |
| // Write Burst Mode |
| if (Addr[9] == 1'b0) |
| $display (" Write Burst Mode = Programmed Burst Length"); |
| else if (Addr[9] == 1'b1) |
| $display (" Write Burst Mode = Single Location Access"); |
| else |
| $display (" Write Burst Mode = Reserved"); |
| end |
| end else begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: all banks must be Precharge before Load Mode Register", $time); |
| end |
| // REF to LMR |
| if ($time - RC_chk < tRC) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRC violation during Load Mode Register", $time); |
| end |
| // LMR to LMR |
| if (MRD_chk < tMRD) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tMRD violation during Load Mode Register", $time); |
| end |
| MRD_chk = 0; |
| end |
| |
| // Active Block (Latch Bank Address and Row Address) |
| if (Active_enable == 1'b1) begin |
| if (Ba == 2'b00 && Pc_b0 == 1'b1) begin |
| {Act_b0, Pc_b0} = 2'b10; |
| B0_row_addr = Addr [addr_bits - 1 : 0]; |
| RCD_chk0 = $time; |
| RAS_chk0 = $time; |
| if (Debug) $display ("at time %t ACT : Bank = 0 Row = %d", $time, Addr); |
| // Precharge to Activate Bank 0 |
| if ($time - RP_chk0 < tRP) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRP violation during Activate bank 0", $time); |
| end |
| end else if (Ba == 2'b01 && Pc_b1 == 1'b1) begin |
| {Act_b1, Pc_b1} = 2'b10; |
| B1_row_addr = Addr [addr_bits - 1 : 0]; |
| RCD_chk1 = $time; |
| RAS_chk1 = $time; |
| if (Debug) $display ("at time %t ACT : Bank = 1 Row = %d", $time, Addr); |
| // Precharge to Activate Bank 1 |
| if ($time - RP_chk1 < tRP) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRP violation during Activate bank 1", $time); |
| end |
| end else if (Ba == 2'b10 && Pc_b2 == 1'b1) begin |
| {Act_b2, Pc_b2} = 2'b10; |
| B2_row_addr = Addr [addr_bits - 1 : 0]; |
| RCD_chk2 = $time; |
| RAS_chk2 = $time; |
| if (Debug) $display ("at time %t ACT : Bank = 2 Row = %d", $time, Addr); |
| // Precharge to Activate Bank 2 |
| if ($time - RP_chk2 < tRP) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRP violation during Activate bank 2", $time); |
| end |
| end else if (Ba == 2'b11 && Pc_b3 == 1'b1) begin |
| {Act_b3, Pc_b3} = 2'b10; |
| B3_row_addr = Addr [addr_bits - 1 : 0]; |
| RCD_chk3 = $time; |
| RAS_chk3 = $time; |
| if (Debug) $display ("at time %t ACT : Bank = 3 Row = %d", $time, Addr); |
| // Precharge to Activate Bank 3 |
| if ($time - RP_chk3 < tRP) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRP violation during Activate bank 3", $time); |
| end |
| end else if (Ba == 2'b00 && Pc_b0 == 1'b0) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: Bank 0 is not Precharged.", $time); |
| end else if (Ba == 2'b01 && Pc_b1 == 1'b0) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: Bank 1 is not Precharged.", $time); |
| end else if (Ba == 2'b10 && Pc_b2 == 1'b0) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: Bank 2 is not Precharged.", $time); |
| end else if (Ba == 2'b11 && Pc_b3 == 1'b0) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: Bank 3 is not Precharged.", $time); |
| end |
| // Active Bank A to Active Bank B |
| if ((Previous_bank != Ba) && ($time - RRD_chk < tRRD)) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRRD violation during Activate bank = %d", $time, Ba); |
| end |
| // Load Mode Register to Active |
| if (MRD_chk < tMRD ) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tMRD violation during Activate bank = %d", $time, Ba); |
| end |
| // Auto Refresh to Activate |
| if ($time - RC_chk < tRC) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRC violation during Activate bank = %d", $time, Ba); |
| end |
| // Record variables for checking violation |
| RRD_chk = $time; |
| Previous_bank = Ba; |
| end |
| |
| // Precharge Block |
| if (Prech_enable == 1'b1) begin |
| if (Addr[10] == 1'b1) begin |
| {Pc_b0, Pc_b1, Pc_b2, Pc_b3} = 4'b1111; |
| {Act_b0, Act_b1, Act_b2, Act_b3} = 4'b0000; |
| RP_chk0 = $time; |
| RP_chk1 = $time; |
| RP_chk2 = $time; |
| RP_chk3 = $time; |
| if (Debug) $display ("at time %t PRE : Bank = ALL",$time); |
| // Activate to Precharge all banks |
| if (($time - RAS_chk0 < tRAS) || ($time - RAS_chk1 < tRAS) || |
| ($time - RAS_chk2 < tRAS) || ($time - RAS_chk3 < tRAS)) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRAS violation during Precharge all bank", $time); |
| if($time - RAS_chk0 < tRAS) |
| $display("ERROR: RAS_CHK0 Rxp: %t Exd: %t",$time - RAS_chk0,tRAS); |
| if($time - RAS_chk1 < tRAS) |
| $display("ERROR: RAS_CHK1 Rxp: %t Exd: %t",$time - RAS_chk1,tRAS); |
| if($time - RAS_chk2 < tRAS) |
| $display("ERROR: RAS_CHK2 Rxp: %t Exd: %t",$time - RAS_chk2,tRAS); |
| if($time - RAS_chk3 < tRAS) |
| $display("ERROR: RAS_CHK3 Rxp: %t Exd: %t",$time - RAS_chk3,tRAS); |
| end |
| // tWR violation check for write |
| if (($time - WR_chk[0] < tWRp) || ($time - WR_chk[1] < tWRp) || |
| ($time - WR_chk[2] < tWRp) || ($time - WR_chk[3] < tWRp)) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tWR violation during Precharge all bank", $time); |
| end |
| end else if (Addr[10] == 1'b0) begin |
| if (Ba == 2'b00) begin |
| {Pc_b0, Act_b0} = 2'b10; |
| RP_chk0 = $time; |
| if (Debug) $display ("at time %t PRE : Bank = 0",$time); |
| // Activate to Precharge Bank 0 |
| if ($time - RAS_chk0 < tRAS) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRAS violation during Precharge bank 0", $time); |
| end |
| end else if (Ba == 2'b01) begin |
| {Pc_b1, Act_b1} = 2'b10; |
| RP_chk1 = $time; |
| if (Debug) $display ("at time %t PRE : Bank = 1",$time); |
| // Activate to Precharge Bank 1 |
| if ($time - RAS_chk1 < tRAS) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRAS violation during Precharge bank 1", $time); |
| end |
| end else if (Ba == 2'b10) begin |
| {Pc_b2, Act_b2} = 2'b10; |
| RP_chk2 = $time; |
| if (Debug) $display ("at time %t PRE : Bank = 2",$time); |
| // Activate to Precharge Bank 2 |
| if ($time - RAS_chk2 < tRAS) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRAS violation during Precharge bank 2", $time); |
| end |
| end else if (Ba == 2'b11) begin |
| {Pc_b3, Act_b3} = 2'b10; |
| RP_chk3 = $time; |
| if (Debug) $display ("at time %t PRE : Bank = 3",$time); |
| // Activate to Precharge Bank 3 |
| if ($time - RAS_chk3 < tRAS) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tRAS violation during Precharge bank 3", $time); |
| end |
| end |
| // tWR violation check for write |
| if ($time - WR_chk[Ba] < tWRp) begin |
| |
| ->error_detected; |
| $display ("at time %t ERROR: tWR violation during Precharge bank %d", $time, Ba); |
| end |
| end |
| // Terminate a Write Immediately (if same bank or all banks) |
| if (Data_in_enable == 1'b1 && (Bank == Ba || Addr[10] == 1'b1)) begin |
| Data_in_enable = 1'b0; |
| end |
| // Precharge Command Pipeline for Read |
| if (Cas_latency_3 == 1'b1) begin |
| Command[2] = `SDRAM_PRECH; |
| Bank_precharge[2] = Ba; |
| A10_precharge[2] = Addr[10]; |
| end else if (Cas_latency_2 == 1'b1) begin |
| Command[1] = `SDRAM_PRECH; |
| Bank_precharge[1] = Ba; |
| A10_precharge[1] = Addr[10]; |
| end |
| end |
| |
| // Burst terminate |
| if (Burst_term == 1'b1) begin |
| // Terminate a Write Immediately |
| if (Data_in_enable == 1'b1) begin |
| Data_in_enable = 1'b0; |
| end |
| // Terminate a Read Depend on CAS Latency |
| if (Cas_latency_3 == 1'b1) begin |
| Command[2] = `SDRAM_BST; |
| end else if (Cas_latency_2 == 1'b1) begin |
| Command[1] = `SDRAM_BST; |
| end |
| if (Debug) $display ("at time %t BST : Burst Terminate",$time); |
| end |
| |
| // Read, Write, Column Latch |
| if (Read_enable == 1'b1 || Write_enable == 1'b1) begin |
| // Check to see if bank is open (ACT) |
| if ((Ba == 2'b00 && Pc_b0 == 1'b1) || (Ba == 2'b01 && Pc_b1 == 1'b1) || |
| (Ba == 2'b10 && Pc_b2 == 1'b1) || (Ba == 2'b11 && Pc_b3 == 1'b1)) begin |
| |
| ->error_detected; |
| $display("at time %t ERROR: Cannot Read or Write - Bank %d is not Activated", $time, Ba); |
| end |
| // Activate to Read or Write |
| if ((Ba == 2'b00) && ($time - RCD_chk0 < tRCD)) |
| begin |
| ->error_detected; |
| $display("at time %t ERROR: tRCD violation during Read or Write to Bank 0", $time); |
| end |
| |
| if ((Ba == 2'b01) && ($time - RCD_chk1 < tRCD)) |
| begin |
| //->tb.test_control.error_detected; |
| $display("at time %t ERROR: tRCD violation during Read or Write to Bank 1", $time); |
| end |
| if ((Ba == 2'b10) && ($time - RCD_chk2 < tRCD)) |
| begin |
| //->tb.test_control.error_detected; |
| $display("at time %t ERROR: tRCD violation during Read or Write to Bank 2", $time); |
| end |
| if ((Ba == 2'b11) && ($time - RCD_chk3 < tRCD)) |
| begin |
| //->tb.test_control.error_detected; |
| $display("at time %t ERROR: tRCD violation during Read or Write to Bank 3", $time); |
| end |
| // Read Command |
| if (Read_enable == 1'b1) begin |
| // CAS Latency pipeline |
| if (Cas_latency_3 == 1'b1) begin |
| if (Addr[10] == 1'b1) begin |
| Command[2] = `READ_A; |
| end else begin |
| Command[2] = `READ; |
| end |
| Col_addr[2] = Addr; |
| Bank_addr[2] = Ba; |
| end else if (Cas_latency_2 == 1'b1) begin |
| if (Addr[10] == 1'b1) begin |
| Command[1] = `READ_A; |
| end else begin |
| Command[1] = `READ; |
| end |
| Col_addr[1] = Addr; |
| Bank_addr[1] = Ba; |
| end |
| |
| // Read interrupt Write (terminate Write immediately) |
| if (Data_in_enable == 1'b1) begin |
| Data_in_enable = 1'b0; |
| end |
| |
| // Write Command |
| end else if (Write_enable == 1'b1) begin |
| if (Addr[10] == 1'b1) begin |
| Command[0] = `WRITE_A; |
| end else begin |
| Command[0] = `SDRAM_WRITE; |
| end |
| Col_addr[0] = Addr; |
| Bank_addr[0] = Ba; |
| |
| // Write interrupt Write (terminate Write immediately) |
| if (Data_in_enable == 1'b1) begin |
| Data_in_enable = 1'b0; |
| end |
| |
| // Write interrupt Read (terminate Read immediately) |
| if (Data_out_enable == 1'b1) begin |
| Data_out_enable = 1'b0; |
| end |
| end |
| |
| // Interrupting a Write with Autoprecharge |
| if (Auto_precharge[Bank] == 1'b1 && Write_precharge[Bank] == 1'b1) begin |
| RW_interrupt_write[Bank] = 1'b1; |
| if (Debug) $display ("at time %t NOTE : Read/Write Bank %d interrupt Write Bank %d with Autoprecharge", $time, Ba, Bank); |
| end |
| |
| // Interrupting a Read with Autoprecharge |
| if (Auto_precharge[Bank] == 1'b1 && Read_precharge[Bank] == 1'b1) begin |
| RW_interrupt_read[Bank] = 1'b1; |
| if (Debug) $display ("at time %t NOTE : Read/Write Bank %d interrupt Read Bank %d with Autoprecharge", $time, Ba, Bank); |
| end |
| |
| // Read or Write with Auto Precharge |
| if (Addr[10] == 1'b1) begin |
| Auto_precharge[Ba] = 1'b1; |
| Count_precharge[Ba] = 0; |
| if (Read_enable == 1'b1) begin |
| Read_precharge[Ba] = 1'b1; |
| end else if (Write_enable == 1'b1) begin |
| Write_precharge[Ba] = 1'b1; |
| end |
| end |
| end |
| |
| // Read with Auto Precharge Calculation |
| // The device start internal precharge: |
| // 1. CAS Latency - 1 cycles before last burst |
| // and 2. Meet minimum tRAS requirement |
| // or 3. Interrupt by a Read or Write (with or without AutoPrecharge) |
| if ((Auto_precharge[0] == 1'b1) && (Read_precharge[0] == 1'b1)) begin |
| if ((($time - RAS_chk0 >= tRAS) && // Case 2 |
| ((Burst_length_1 == 1'b1 && Count_precharge[0] >= 1) || // Case 1 |
| (Burst_length_2 == 1'b1 && Count_precharge[0] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge[0] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge[0] >= 8))) || |
| (RW_interrupt_read[0] == 1'b1)) begin // Case 3 |
| Pc_b0 = 1'b1; |
| Act_b0 = 1'b0; |
| RP_chk0 = $time; |
| Auto_precharge[0] = 1'b0; |
| Read_precharge[0] = 1'b0; |
| RW_interrupt_read[0] = 1'b0; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 0", $time); |
| end |
| end |
| if ((Auto_precharge[1] == 1'b1) && (Read_precharge[1] == 1'b1)) begin |
| if ((($time - RAS_chk1 >= tRAS) && |
| ((Burst_length_1 == 1'b1 && Count_precharge[1] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge[1] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge[1] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge[1] >= 8))) || |
| (RW_interrupt_read[1] == 1'b1)) begin |
| Pc_b1 = 1'b1; |
| Act_b1 = 1'b0; |
| RP_chk1 = $time; |
| Auto_precharge[1] = 1'b0; |
| Read_precharge[1] = 1'b0; |
| RW_interrupt_read[1] = 1'b0; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 1", $time); |
| end |
| end |
| if ((Auto_precharge[2] == 1'b1) && (Read_precharge[2] == 1'b1)) begin |
| if ((($time - RAS_chk2 >= tRAS) && |
| ((Burst_length_1 == 1'b1 && Count_precharge[2] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge[2] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge[2] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge[2] >= 8))) || |
| (RW_interrupt_read[2] == 1'b1)) begin |
| Pc_b2 = 1'b1; |
| Act_b2 = 1'b0; |
| RP_chk2 = $time; |
| Auto_precharge[2] = 1'b0; |
| Read_precharge[2] = 1'b0; |
| RW_interrupt_read[2] = 1'b0; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 2", $time); |
| end |
| end |
| if ((Auto_precharge[3] == 1'b1) && (Read_precharge[3] == 1'b1)) begin |
| if ((($time - RAS_chk3 >= tRAS) && |
| ((Burst_length_1 == 1'b1 && Count_precharge[3] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge[3] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge[3] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge[3] >= 8))) || |
| (RW_interrupt_read[3] == 1'b1)) begin |
| Pc_b3 = 1'b1; |
| Act_b3 = 1'b0; |
| RP_chk3 = $time; |
| Auto_precharge[3] = 1'b0; |
| Read_precharge[3] = 1'b0; |
| RW_interrupt_read[3] = 1'b0; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 3", $time); |
| end |
| end |
| |
| // Internal Precharge or Bst |
| if (Command[0] == `SDRAM_PRECH) begin // Precharge terminate a read with same bank or all banks |
| if (Bank_precharge[0] == Bank || A10_precharge[0] == 1'b1) begin |
| if (Data_out_enable == 1'b1) begin |
| Data_out_enable = 1'b0; |
| end |
| end |
| end else if (Command[0] == `SDRAM_BST) begin // BST terminate a read to current bank |
| if (Data_out_enable == 1'b1) begin |
| Data_out_enable = 1'b0; |
| end |
| end |
| |
| if (Data_out_enable == 1'b0) begin |
| Dq_reg <= #tOH {data_bits{1'bz}}; |
| end |
| |
| // Detect Read or Write command |
| if (Command[0] == `READ || Command[0] == `READ_A) begin |
| Bank = Bank_addr[0]; |
| Col = Col_addr[0]; |
| Col_brst = Col_addr[0]; |
| if (Bank_addr[0] == 2'b00) begin |
| Row = B0_row_addr; |
| end else if (Bank_addr[0] == 2'b01) begin |
| Row = B1_row_addr; |
| end else if (Bank_addr[0] == 2'b10) begin |
| Row = B2_row_addr; |
| end else if (Bank_addr[0] == 2'b11) begin |
| Row = B3_row_addr; |
| end |
| Burst_counter = 0; |
| Data_in_enable = 1'b0; |
| Data_out_enable = 1'b1; |
| end else if (Command[0] == `SDRAM_WRITE || Command[0] == `WRITE_A) begin |
| Bank = Bank_addr[0]; |
| Col = Col_addr[0]; |
| Col_brst = Col_addr[0]; |
| if (Bank_addr[0] == 2'b00) begin |
| Row = B0_row_addr; |
| end else if (Bank_addr[0] == 2'b01) begin |
| Row = B1_row_addr; |
| end else if (Bank_addr[0] == 2'b10) begin |
| Row = B2_row_addr; |
| end else if (Bank_addr[0] == 2'b11) begin |
| Row = B3_row_addr; |
| end |
| Burst_counter = 0; |
| Data_in_enable = 1'b1; |
| Data_out_enable = 1'b0; |
| end |
| |
| // DQ buffer (Driver/Receiver) |
| if (Data_in_enable == 1'b1) begin // Writing Data to Memory |
| // Array buffer |
| if (Bank == 2'b00) Dq_dqm [15 : 0] = Bank0 [{Row, Col}]; |
| if (Bank == 2'b01) Dq_dqm [15 : 0] = Bank1 [{Row, Col}]; |
| if (Bank == 2'b10) Dq_dqm [15 : 0] = Bank2 [{Row, Col}]; |
| if (Bank == 2'b11) Dq_dqm [15 : 0] = Bank3 [{Row, Col}]; |
| // Dqm operation |
| if (Dqm[0] == 1'b0) Dq_dqm [ 7 : 0] = Dq [ 7 : 0]; |
| // Write to memory |
| if (Bank == 2'b00) Bank0 [{Row, Col}] = Dq_dqm [15 : 0]; |
| if (Bank == 2'b01) Bank1 [{Row, Col}] = Dq_dqm [15 : 0]; |
| if (Bank == 2'b10) Bank2 [{Row, Col}] = Dq_dqm [15 : 0]; |
| if (Bank == 2'b11) Bank3 [{Row, Col}] = Dq_dqm [15 : 0]; |
| // Output result |
| if (Dqm == 1'b1) begin |
| if (Debug) $display("at time %t WRITE: Bank = %d Row = %d, Col = %d, Data = Hi-Z due to DQM", $time, Bank, Row, Col); |
| end else begin |
| if (Debug) $display("at time %t WRITE: Bank = %d Row = %d, Col = %d, Data = %h, Dqm = %b", $time, Bank, Row, Col, Dq_dqm, Dqm); |
| // Record tWR time and reset counter |
| WR_chk [Bank] = $time; |
| WR_counter [Bank] = 0; |
| end |
| // Advance burst counter subroutine |
| #tHZ Burst; |
| end else if (Data_out_enable == 1'b1) begin // Reading Data from Memory |
| // Array buffer |
| if (Bank == 2'b00) Dq_dqm [15 : 0] = Bank0 [{Row, Col}]; |
| if (Bank == 2'b01) Dq_dqm [15 : 0] = Bank1 [{Row, Col}]; |
| if (Bank == 2'b10) Dq_dqm [15 : 0] = Bank2 [{Row, Col}]; |
| if (Bank == 2'b11) Dq_dqm [15 : 0] = Bank3 [{Row, Col}]; |
| // Dqm operation |
| if (Dqm_reg0[0] == 1'b1) Dq_dqm [ 7 : 0] = 8'bz; |
| // Display result |
| Dq_reg [15 : 0] = #tAC Dq_dqm [15 : 0]; |
| if (Dqm_reg0 == 1'b1) begin |
| if (Debug) $display("at time %t READ : Bank = %d Row = %d, Col = %d, Data = Hi-Z due to DQM", $time, Bank, Row, Col); |
| end else begin |
| if (Debug) $display("at time %t READ : Bank = %d Row = %d, Col = %d, Data = %h, Dqm = %b", $time, Bank, Row, Col, Dq_reg, Dqm_reg0); |
| end |
| // Advance burst counter subroutine |
| Burst; |
| end |
| end |
| |
| // Write with Auto Precharge Calculation |
| // The device start internal precharge: |
| // 1. tWR Clock after last burst |
| // and 2. Meet minimum tRAS requirement |
| // or 3. Interrupt by a Read or Write (with or without AutoPrecharge) |
| always @ (WR_counter[0]) begin |
| if ((Auto_precharge[0] == 1'b1) && (Write_precharge[0] == 1'b1)) begin |
| if ((($time - RAS_chk0 >= tRAS) && // Case 2 |
| (((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [0] >= 1) || // Case 1 |
| (Burst_length_2 == 1'b1 && Count_precharge [0] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge [0] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge [0] >= 8))) || |
| (RW_interrupt_write[0] == 1'b1 && WR_counter[0] >= 2)) begin // Case 3 (stop count when interrupt) |
| Auto_precharge[0] = 1'b0; |
| Write_precharge[0] = 1'b0; |
| RW_interrupt_write[0] = 1'b0; |
| #tWRa; // Wait for tWR |
| Pc_b0 = 1'b1; |
| Act_b0 = 1'b0; |
| RP_chk0 = $time; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 0", $time); |
| end |
| end |
| end |
| always @ (WR_counter[1]) begin |
| if ((Auto_precharge[1] == 1'b1) && (Write_precharge[1] == 1'b1)) begin |
| if ((($time - RAS_chk1 >= tRAS) && |
| (((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [1] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge [1] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge [1] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge [1] >= 8))) || |
| (RW_interrupt_write[1] == 1'b1 && WR_counter[1] >= 2)) begin |
| Auto_precharge[1] = 1'b0; |
| Write_precharge[1] = 1'b0; |
| RW_interrupt_write[1] = 1'b0; |
| #tWRa; // Wait for tWR |
| Pc_b1 = 1'b1; |
| Act_b1 = 1'b0; |
| RP_chk1 = $time; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 1", $time); |
| end |
| end |
| end |
| always @ (WR_counter[2]) begin |
| if ((Auto_precharge[2] == 1'b1) && (Write_precharge[2] == 1'b1)) begin |
| if ((($time - RAS_chk2 >= tRAS) && |
| (((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [2] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge [2] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge [2] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge [2] >= 8))) || |
| (RW_interrupt_write[2] == 1'b1 && WR_counter[2] >= 2)) begin |
| Auto_precharge[2] = 1'b0; |
| Write_precharge[2] = 1'b0; |
| RW_interrupt_write[2] = 1'b0; |
| #tWRa; // Wait for tWR |
| Pc_b2 = 1'b1; |
| Act_b2 = 1'b0; |
| RP_chk2 = $time; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 2", $time); |
| end |
| end |
| end |
| always @ (WR_counter[3]) begin |
| if ((Auto_precharge[3] == 1'b1) && (Write_precharge[3] == 1'b1)) begin |
| if ((($time - RAS_chk3 >= tRAS) && |
| (((Burst_length_1 == 1'b1 || Write_burst_mode == 1'b1) && Count_precharge [3] >= 1) || |
| (Burst_length_2 == 1'b1 && Count_precharge [3] >= 2) || |
| (Burst_length_4 == 1'b1 && Count_precharge [3] >= 4) || |
| (Burst_length_8 == 1'b1 && Count_precharge [3] >= 8))) || |
| (RW_interrupt_write[3] == 1'b1 && WR_counter[3] >= 2)) begin |
| Auto_precharge[3] = 1'b0; |
| Write_precharge[3] = 1'b0; |
| RW_interrupt_write[3] = 1'b0; |
| #tWRa; // Wait for tWR |
| Pc_b3 = 1'b1; |
| Act_b3 = 1'b0; |
| RP_chk3 = $time; |
| if (Debug) $display ("at time %t NOTE : Start Internal Auto Precharge for Bank 3", $time); |
| end |
| end |
| end |
| |
| task Burst; |
| begin |
| // Advance Burst Counter |
| Burst_counter = Burst_counter + 1; |
| |
| // Burst Type |
| if (Mode_reg[3] == 1'b0) begin // Sequential Burst |
| Col_temp = Col + 1; |
| end else if (Mode_reg[3] == 1'b1) begin // Interleaved Burst |
| Col_temp[2] = Burst_counter[2] ^ Col_brst[2]; |
| Col_temp[1] = Burst_counter[1] ^ Col_brst[1]; |
| Col_temp[0] = Burst_counter[0] ^ Col_brst[0]; |
| end |
| |
| // Burst Length |
| if (Burst_length_2) begin // Burst Length = 2 |
| Col [0] = Col_temp [0]; |
| end else if (Burst_length_4) begin // Burst Length = 4 |
| Col [1 : 0] = Col_temp [1 : 0]; |
| end else if (Burst_length_8) begin // Burst Length = 8 |
| Col [2 : 0] = Col_temp [2 : 0]; |
| end else begin // Burst Length = FULL |
| Col = Col_temp; |
| end |
| |
| // Burst Read Single Write |
| if (Write_burst_mode == 1'b1) begin |
| Data_in_enable = 1'b0; |
| end |
| |
| // Data Counter |
| if (Burst_length_1 == 1'b1) begin |
| if (Burst_counter >= 1) begin |
| Data_in_enable = 1'b0; |
| Data_out_enable = 1'b0; |
| end |
| end else if (Burst_length_2 == 1'b1) begin |
| if (Burst_counter >= 2) begin |
| Data_in_enable = 1'b0; |
| Data_out_enable = 1'b0; |
| end |
| end else if (Burst_length_4 == 1'b1) begin |
| if (Burst_counter >= 4) begin |
| Data_in_enable = 1'b0; |
| Data_out_enable = 1'b0; |
| end |
| end else if (Burst_length_8 == 1'b1) begin |
| if (Burst_counter >= 8) begin |
| Data_in_enable = 1'b0; |
| Data_out_enable = 1'b0; |
| end |
| end |
| end |
| endtask |
| |
| // Timing Parameters for -75 (PC133) and CAS Latency = 2 |
| specify |
| specparam |
| tAH = 0.8, // Addr, Ba Hold Time |
| tAS = 1.5, // Addr, Ba Setup Time |
| tCH = 2.5, // Clock High-Level Width |
| tCL = 2.5, // Clock Low-Level Width |
| tCK = 10, // Clock Cycle Time |
| tDH = 0.8, // Data-in Hold Time |
| tDS = 1.5, // Data-in Setup Time |
| tCKH = 0.8, // CKE Hold Time |
| tCKS = 1.5, // CKE Setup Time |
| tCMH = 0.8, // CS#, RAS#, CAS#, WE#, DQM# Hold Time |
| tCMS = 1.5; // CS#, RAS#, CAS#, WE#, DQM# Setup Time |
| $width (posedge Clk, tCH); |
| $width (negedge Clk, tCL); |
| $period (negedge Clk, tCK); |
| $period (posedge Clk, tCK); |
| $setuphold(posedge Clk, Cke, tCKS, tCKH); |
| $setuphold(posedge Clk, Cs_n, tCMS, tCMH); |
| $setuphold(posedge Clk, Cas_n, tCMS, tCMH); |
| $setuphold(posedge Clk, Ras_n, tCMS, tCMH); |
| $setuphold(posedge Clk, We_n, tCMS, tCMH); |
| $setuphold(posedge Clk, Addr, tAS, tAH); |
| $setuphold(posedge Clk, Ba, tAS, tAH); |
| $setuphold(posedge Clk, Dqm, tCMS, tCMH); |
| $setuphold(posedge Dq_chk, Dq, tDS, tDH); |
| endspecify |
| |
| endmodule |
| |