blob: 317341d2caf7eae344a4e57854a866e954036225 [file] [log] [blame]
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
`default_nettype none
`timescale 1 ns / 1 ps
module peripheralsGPIO_tb;
reg clock;
reg RSTB;
reg CSB;
reg power1, power2;
reg power3, power4;
wire gpio;
wire [37:0] mprj_io;
reg[1:0] inputTestData;
wire succesOutput = mprj_io[12];
wire nextTestOutput = mprj_io[13];
wire[3:0] outputTestData = mprj_io[17:14];
assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz;
assign mprj_io[20:19] = inputTestData;
// External clock is used by default. Make this artificially fast for the
// simulation. Normally this would be a slow clock and the digital PLL
// would be the fast clock.
always #12.5 clock <= (clock === 1'b0);
initial begin
clock = 0;
inputTestData = 4'b0;
end
// Generate input signal
initial begin
@(posedge nextTestOutput);
inputTestData = 2'b10;
@(posedge nextTestOutput);
inputTestData = 2'b01;
@(posedge nextTestOutput);
inputTestData = 2'b11;
@(posedge nextTestOutput);
inputTestData = 2'b00;
end
initial begin
$dumpfile("peripheralsGPIO.vcd");
$dumpvars(0, peripheralsGPIO_tb);
// Repeat cycles of 1000 clock edges as needed to complete testbench
repeat (300) begin
repeat (1000) @(posedge clock);
//$display("+1000 cycles");
end
$display("%c[1;35m",27);
`ifdef GL
$display ("Monitor: Timeout, Peripherals GPIO Test (GL) Failed");
`else
$display ("Monitor: Timeout, Peripherals GPIO Test (RTL) Failed");
`endif
$display("%c[0m",27);
$finish;
end
initial begin
// Observe Output pins
wait(outputTestData == 4'b0000);
wait(outputTestData == 4'b0001);
wait(outputTestData == 4'b0011);
wait(outputTestData == 4'b0111);
wait(outputTestData == 4'b1111);
wait(outputTestData == 4'b0000);
wait(outputTestData == 4'b1111);
wait(outputTestData == 4'b1110);
wait(outputTestData == 4'b1100);
wait(outputTestData == 4'b1000);
wait(outputTestData == 4'b0000);
// Wait for tests
@(posedge nextTestOutput);
@(posedge nextTestOutput);
@(posedge nextTestOutput);
@(posedge nextTestOutput);
// Wait for management core to output a output test result
@(posedge nextTestOutput);
if (succesOutput) begin
$display("%c[1;92m",27);
`ifdef GL
$display("Monitor: Peripherals GPIO Test (GL) Passed");
`else
$display("Monitor: Peripherals GPIO Test (RTL) Passed");
`endif
$display("%c[0m",27);
end else begin
$display("%c[1;31m",27);
`ifdef GL
$display ("Monitor: Peripherals GPIO Test (GL) Failed");
`else
$display ("Monitor: Peripherals GPIO Test (RTL) Failed");
`endif
$display("%c[0m",27);
end
$finish;
end
initial begin
RSTB <= 1'b0;
CSB <= 1'b1; // Force CSB high
#2000;
RSTB <= 1'b1; // Release reset
#300000;
CSB = 1'b0; // CSB can be released
end
initial begin // Power-up sequence
power1 <= 1'b0;
power2 <= 1'b0;
power3 <= 1'b0;
power4 <= 1'b0;
#100;
power1 <= 1'b1;
#100;
power2 <= 1'b1;
#100;
power3 <= 1'b1;
#100;
power4 <= 1'b1;
end
always @(succesOutput, nextTestOutput, outputTestData, inputTestData) begin
#1 $display("Success:0b%b Next test:0b%b Output:0b%b Input:0b%b", succesOutput, nextTestOutput, outputTestData, inputTestData);
end
wire flash_csb;
wire flash_clk;
wire flash_io0;
wire flash_io1;
wire VDD3V3;
wire VDD1V8;
wire VSS;
assign VDD3V3 = power1;
assign VDD1V8 = power2;
assign VSS = 1'b0;
caravel uut (
.vddio (VDD3V3),
.vddio_2 (VDD3V3),
.vssio (VSS),
.vssio_2 (VSS),
.vdda (VDD3V3),
.vssa (VSS),
.vccd (VDD1V8),
.vssd (VSS),
.vdda1 (VDD3V3),
.vdda1_2 (VDD3V3),
.vdda2 (VDD3V3),
.vssa1 (VSS),
.vssa1_2 (VSS),
.vssa2 (VSS),
.vccd1 (VDD1V8),
.vccd2 (VDD1V8),
.vssd1 (VSS),
.vssd2 (VSS),
.clock (clock),
.gpio (gpio),
.mprj_io (mprj_io),
.flash_csb(flash_csb),
.flash_clk(flash_clk),
.flash_io0(flash_io0),
.flash_io1(flash_io1),
.resetb (RSTB)
);
spiflash #(
.FILENAME("peripheralsGPIO.hex")
) spiflash (
.csb(flash_csb),
.clk(flash_clk),
.io0(flash_io0),
.io1(flash_io1),
.io2(), // not used
.io3() // not used
);
endmodule
`default_nettype wire