blob: c9de5f16af5c7edf658a280482ee808b79ed3a1a [file] [log] [blame]
//////////////////////////////////////////////////////////////////////////////
// SPDX-FileCopyrightText: 2021 , Dinesh Annayya
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
// http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
// SPDX-FileContributor: Created by Dinesh Annayya <dinesha@opencores.org>
//
//////////////////////////////////////////////////////////////////////
//// ////
//// Pinmux ////
//// ////
//// This file is part of the riscduino cores project ////
//// https://github.com/dineshannayya/riscduino.git ////
//// ////
//// Description ////
//// PinMux Manages all the pin multiplexing ////
//// ////
//// To Do: ////
//// nothing ////
//// ////
//// Author(s): ////
//// - Dinesh Annayya, dinesha@opencores.org ////
//// ////
//// Revision : ////
//// 0.1 - 16th Feb 2021, Dinesh A ////
//// initial version ////
//// 0.2 - 6 April 2021, Dinesh A ////
//// 1. SSPI CS# increased from 1 to 4 ////
// 2. UART I/F increase from 1 to 2 ////
//// 0.3 - 8 July 2022, Dinesh A ////
//// In ardunio, SPI chip select are control through ////
//// GPIO, So we have moved the Auto generated SPI CS ////
//// different config bit. I2C config position moved from////
//// bit[14] to bit [15] ////
//// 0.4 - 20 July 2022, Dinesh A ////
//// On Power On, If RESET* = 0, then system will enter ////
//// in to SPIS slave mode to support boot ////
//// 0.5 Aug 5 2022, Dinesh A ////
//// changes in sspim ////
//// A. SPI Mode 0 to 3 support added, ////
//// B. SPI Duplex mode TX-RX Mode added ////
//// 0.6 Aug 15 2022, Dinesh A ////
//// A. 15 Hardware Semahore added ////
//// 0.7 - 24 Aug 2022, Dinesh A ////
//// A. GPIO interrupt generation changed from 1 to 32 ////
//// B. uart_master disable option added ////
//// C. Timer interrupt related clean-up ////
//// D. 4x ws281x driver logic added ////
//// E. 4x ws281x driver are mux with 16x gpio ////
//// F. gpio type select the normal gpio vs ws281x ////
//// 0.7 - 26th Aug 2022, Dinesh A ////
//// As digitial-io[0-4] reserved at power up. ////
//// A. to keep at least one uart access, ////
//// we have moved UART_RXD[1] from io[3] to io[6] ////
//// B. SPI Slave SSN move from io[0] to [7] ////
//// C. Additional Mail Box Register added at addr 0xF ////
//// D. Due to power on digitalio[0-4] access issue,we ////
//// have moved arduino pin mapping from io 5 onward ////
//// 0.8 - 1 Sept 2022, Dinesh A ////
//// A. System strap implementation ////
//// B. glbl address space increased from 16 to 32 ////
//// C. software register address moved, 4 register will ////
//// reset under power-on reset, 4 register will reset////
//// system reset ////
//////////////////////////////////////////////////////////////////////
`include "user_params.svh"
module pinmux_top (
`ifdef USE_POWER_PINS
input logic vccd1,// User area 1 1.8V supply
input logic vssd1,// User area 1 digital ground
`endif
// clock skew adjust
input logic [3:0] cfg_cska_pinmux,
input logic wbd_clk_int,
output logic wbd_clk_pinmux,
// System Signals
// Inputs
input logic mclk,
input logic e_reset_n , // external reset
input logic p_reset_n , // power-on reset
input logic s_reset_n , // soft reset
// to/from Global Reset FSM
input logic cfg_strap_pad_ctrl ,
input logic [31:0] system_strap ,
output logic [31:0] strap_sticky ,
output logic [1:0] strap_uartm ,
input logic user_clock1 ,
input logic user_clock2 ,
input logic int_pll_clock ,
input logic cpu_clk ,
output logic xtal_clk ,
output logic usb_clk ,
output logic rtc_clk ,
// Global Reset control
output logic [1:0] cpu_core_rst_n ,
output logic cpu_intf_rst_n ,
output logic qspim_rst_n ,
output logic sspim_rst_n ,
output logic [1:0] uart_rst_n ,
output logic i2cm_rst_n ,
output logic usb_rst_n ,
output logic [15:0] cfg_riscv_ctrl,
// Reg Bus Interface Signal
input logic reg_cs,
input logic reg_wr,
input logic [9:0] reg_addr,
input logic [31:0] reg_wdata,
input logic [3:0] reg_be,
// Outputs
output logic [31:0] reg_rdata,
output logic reg_ack,
// Risc configuration
output logic [31:0] irq_lines,
output logic soft_irq,
output logic [2:0] user_irq,
input logic usb_intr,
input logic i2cm_intr,
// Digital IO
output logic [37:0] digital_io_out,
output logic [37:0] digital_io_oen,
input logic [37:0] digital_io_in,
// SFLASH I/F
input logic sflash_sck,
input logic [3:0] sflash_ss,
input logic [3:0] sflash_oen,
input logic [3:0] sflash_do,
output logic [3:0] sflash_di,
// SSRAM I/F - Temp Masked
//input logic ssram_sck,
//input logic ssram_ss,
//input logic [3:0] ssram_oen,
//input logic [3:0] ssram_do,
//output logic [3:0] ssram_di,
// USB I/F
input logic usb_dp_o,
input logic usb_dn_o,
input logic usb_oen,
output logic usb_dp_i,
output logic usb_dn_i,
// UART I/F
input logic [1:0] uart_txd,
output logic [1:0] uart_rxd,
// I2CM I/F
input logic i2cm_clk_o,
output logic i2cm_clk_i,
input logic i2cm_clk_oen,
input logic i2cm_data_oen,
input logic i2cm_data_o,
output logic i2cm_data_i,
// SPI MASTER
input logic spim_sck,
input logic [3:0] spim_ssn,
input logic spim_miso,
output logic spim_mosi,
// SPI SLAVE
output logic spis_sck,
output logic spis_ssn,
input logic spis_miso,
output logic spis_mosi,
// UART MASTER I/F
output logic uartm_rxd ,
input logic uartm_txd ,
output logic pulse1m_mclk,
output logic [31:0] pinmux_debug,
// Digital PLL I/F
output logic cfg_pll_enb , // Enable PLL
output logic[4:0] cfg_pll_fed_div , // PLL feedback division ratio
output logic cfg_dco_mode , // Run PLL in DCO mode
output logic[25:0] cfg_dc_trim , // External trim for DCO mode
output logic pll_ref_clk // Input oscillator to match
);
logic s_reset_ssn; // Sync Reset
logic p_reset_ssn; // Sync Reset
logic [15:0] pad_strap_in;
logic dbg_clk_mon;
/* clock pulse */
//********************************************************
logic pulse_1ms ; // 1 Milli Second Pulse for waveform Generator
logic [5:0] cfg_pwm_enb ;
//---------------------------------------------------------
// Timer Register
// -------------------------------------------------------
logic [2:0] timer_intr ;
//---------------------------------------------------
// 6 PWM variabled
//---------------------------------------------------
logic [5:0] pwm_wfm ;
logic [31:0] gpio_intr ;
wire [31:0] cfg_gpio_dir_sel ;// decides on GPIO pin is I/P or O/P at pad level, 0 -> Input, 1 -> Output
wire [31:0] cfg_gpio_out_type ;// GPIO Type, Unused
wire [31:0] cfg_multi_func_sel ;// GPIO Multi function type
reg [7:0] port_a_in; // PORT A Data In
reg [7:0] port_b_in; // PORT B Data In
reg [7:0] port_c_in; // PORT C Data In
reg [7:0] port_d_in; // PORT D Data In
wire [7:0] port_a_out; // PORT A Data Out
wire [7:0] port_b_out; // PORT B Data Out
wire [7:0] port_c_out; // PORT C Data Out
wire [7:0] port_d_out; // PORT D Data Out
wire [31:0] pad_gpio_in; // GPIO data input from PAD
wire [31:0] pad_gpio_out; // GPIO Data out towards PAD
wire [31:0] gpio_int_event; // GPIO Interrupt indication
reg [1:0] ext_intr_in; // External PAD level interrupt
logic [3:0] ws_txd ; // ws281x txd port
assign pinmux_debug = '0; // Todo: Need to fix
//------------------------------------------------------
// Register Map Decoding
`define SEL_GLBL 3'b000 // GLOBAL REGISTER
`define SEL_GPIO 3'b001 // GPIO REGISTER
`define SEL_PWM 3'b010 // PWM REGISTER
`define SEL_TIMER 3'b011 // TIMER REGISTER
`define SEL_SEMA 3'b100 // SEMAPHORE REGISTER
`define SEL_WS 3'b101 // WS281x REGISTER
//----------------------------------------
// Register Response Path Mux
// --------------------------------------
logic [31:0] reg_glbl_rdata;
logic reg_glbl_ack;
logic [31:0] reg_gpio_rdata;
logic reg_gpio_ack;
logic [31:0] reg_pwm_rdata;
logic reg_pwm_ack;
logic [31:0] reg_timer_rdata;
logic reg_timer_ack;
logic [15:0] reg_sema_rdata;
logic reg_sema_ack;
logic [31:0] reg_ws_rdata;
logic reg_ws_ack;
assign reg_rdata = (reg_addr[9:7] == `SEL_GLBL) ? {reg_glbl_rdata} :
(reg_addr[9:7] == `SEL_GPIO) ? {reg_gpio_rdata} :
(reg_addr[9:7] == `SEL_PWM) ? {reg_pwm_rdata} :
(reg_addr[9:7] == `SEL_TIMER) ? reg_timer_rdata :
(reg_addr[9:7] == `SEL_SEMA) ? {16'h0,reg_sema_rdata} :
(reg_addr[9:7] == `SEL_WS) ? reg_ws_rdata : 'h0;
assign reg_ack = (reg_addr[9:7] == `SEL_GLBL) ? reg_glbl_ack :
(reg_addr[9:7] == `SEL_GPIO) ? reg_gpio_ack :
(reg_addr[9:7] == `SEL_PWM) ? reg_pwm_ack :
(reg_addr[9:7] == `SEL_TIMER) ? reg_timer_ack :
(reg_addr[9:7] == `SEL_SEMA) ? reg_sema_ack :
(reg_addr[9:7] == `SEL_WS) ? reg_ws_ack : 1'b0;
wire reg_glbl_cs = (reg_addr[9:7] == `SEL_GLBL) ? reg_cs : 1'b0;
wire reg_gpio_cs = (reg_addr[9:7] == `SEL_GPIO) ? reg_cs : 1'b0;
wire reg_pwm_cs = (reg_addr[9:7] == `SEL_PWM) ? reg_cs : 1'b0;
wire reg_timer_cs = (reg_addr[9:7] == `SEL_TIMER)? reg_cs : 1'b0;
wire reg_sema_cs = (reg_addr[9:7] == `SEL_SEMA) ? reg_cs : 1'b0;
wire reg_ws_cs = (reg_addr[9:7] == `SEL_WS) ? reg_cs : 1'b0;
//---------------------------------------------------------------------
// SSRAM I/F - Temp masked
//input logic ssram_sck,
//input logic ssram_ss,
//input logic [3:0] ssram_oen,
//input logic [3:0] ssram_do,
//output logic [3:0] ssram_di,
// pinmux clock skew control
clk_skew_adjust u_skew_pinmux
(
`ifdef USE_POWER_PINS
.vccd1 (vccd1 ),// User area 1 1.8V supply
.vssd1 (vssd1 ),// User area 1 digital ground
`endif
.clk_in (wbd_clk_int ),
.sel (cfg_cska_pinmux ),
.clk_out (wbd_clk_pinmux )
);
reset_sync u_rst_sync (
.scan_mode (1'b0 ),
.dclk (mclk ), // Destination clock domain
.arst_n (s_reset_n ), // active low async reset
.srst_n (s_reset_ssn )
);
reset_sync u_prst_sync (
.scan_mode (1'b0 ),
.dclk (mclk ), // Destination clock domain
.arst_n (p_reset_n ), // active low async reset
.srst_n (p_reset_ssn )
);
//------------------------------------------------------------------
// Global Register
//------------------------------------------------------------------
glbl_reg u_glbl_reg(
// System Signals
// Inputs
.mclk (mclk ),
.e_reset_n (e_reset_n ), // external reset
.p_reset_n (p_reset_ssn ), // power-on reset
.s_reset_n (s_reset_ssn ),
.pad_strap_in (pad_strap_in ),
.system_strap (system_strap ),
.strap_sticky (strap_sticky ),
.strap_uartm (strap_uartm ),
.user_clock1 (user_clock1 ),
.user_clock2 (user_clock2 ),
.int_pll_clock (int_pll_clock ),
.cpu_clk (cpu_clk ),
.xtal_clk (xtal_clk ),
.usb_clk (usb_clk ),
.rtc_clk (rtc_clk ),
.cpu_core_rst_n (cpu_core_rst_n ),
.cpu_intf_rst_n (cpu_intf_rst_n ),
.qspim_rst_n (qspim_rst_n ),
.sspim_rst_n (sspim_rst_n ),
.uart_rst_n (uart_rst_n ),
.i2cm_rst_n (i2cm_rst_n ),
.usb_rst_n (usb_rst_n ),
.cfg_riscv_ctrl (cfg_riscv_ctrl ),
.cfg_multi_func_sel (cfg_multi_func_sel ),
// Reg read/write Interface Inputs
.reg_cs (reg_glbl_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[6:2] ),
.reg_wdata (reg_wdata ),
.reg_be (reg_be ),
.reg_rdata (reg_glbl_rdata ),
.reg_ack (reg_glbl_ack ),
.ext_intr_in (ext_intr_in ),
.irq_lines (irq_lines ),
.soft_irq (soft_irq ),
.user_irq (user_irq ),
.usb_intr (usb_intr ),
.i2cm_intr (i2cm_intr ),
.timer_intr (timer_intr ),
.gpio_intr (gpio_intr ),
// Digital PLL I/F
.cfg_pll_enb (cfg_pll_enb ), // Enable PLL
.cfg_pll_fed_div (cfg_pll_fed_div ), // PLL feedback division ratio
.cfg_dco_mode (cfg_dco_mode ), // Run PLL in DCO mode
.cfg_dc_trim (cfg_dc_trim ), // External trim for DCO mode
.pll_ref_clk (pll_ref_clk ), // Input oscillator to match
.dbg_clk_mon (dbg_clk_mon )
);
//-----------------------------------------------------------------------
// GPIO Top
//-----------------------------------------------------------------------
gpio_top u_gpio(
// System Signals
// Inputs
.mclk ( mclk ),
.h_reset_n (s_reset_ssn ),
// Reg Bus Interface Signal
.reg_cs (reg_gpio_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[5:2] ),
.reg_wdata (reg_wdata ),
.reg_be (reg_be ),
// Outputs
.reg_rdata (reg_gpio_rdata ),
.reg_ack (reg_gpio_ack ),
.cfg_gpio_out_type (cfg_gpio_out_type ),
.cfg_gpio_dir_sel (cfg_gpio_dir_sel ),
.pad_gpio_in (pad_gpio_in ),
.pad_gpio_out (pad_gpio_out ),
.gpio_intr (gpio_intr )
);
//-----------------------------------------------------------------------
// PWM Top
//-----------------------------------------------------------------------
pwm_top u_pwm(
// System Signals
// Inputs
.mclk ( mclk ),
.h_reset_n (s_reset_ssn ),
// Reg Bus Interface Signal
.reg_cs (reg_pwm_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[4:2] ),
.reg_wdata (reg_wdata ),
.reg_be (reg_be ),
// Outputs
.reg_rdata (reg_pwm_rdata ),
.reg_ack (reg_pwm_ack ),
.pulse_1ms (pulse_1ms ),
.cfg_pwm_enb (cfg_pwm_enb ),
.pwm_wfm (pwm_wfm )
);
//-----------------------------------------------------------------------
// Timer Top
//-----------------------------------------------------------------------
timer_top u_timer(
// System Signals
// Inputs
.mclk (mclk ),
.h_reset_n (s_reset_ssn ),
// Reg Bus Interface Signal
.reg_cs (reg_timer_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[3:2] ),
.reg_wdata (reg_wdata ),
.reg_be (reg_be ),
// Outputs
.reg_rdata (reg_timer_rdata ),
.reg_ack (reg_timer_ack ),
.pulse_1ms (pulse_1ms ),
.timer_intr (timer_intr )
);
//-----------------------------------------------------------------------
// Semaphore Register
//-----------------------------------------------------------------------
semaphore_reg u_semaphore(
// System Signals
// Inputs
.mclk ( mclk ),
.h_reset_n (s_reset_ssn ),
// Reg Bus Interface Signal
.reg_cs (reg_sema_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[5:2] ),
.reg_wdata (reg_wdata[15:0] ),
.reg_be (reg_be[1:0] ),
// Outputs
.reg_rdata (reg_sema_rdata ),
.reg_ack (reg_sema_ack )
);
//-----------------------------------------------------------------------
// 4 Port ws281x driver
//----------------------------------------------------------------------
ws281x_top u_ws281x(
.mclk (mclk ),
.h_reset_n (s_reset_ssn ),
.reg_cs (reg_ws_cs ),
.reg_wr (reg_wr ),
.reg_addr (reg_addr[5:2] ),
.reg_wdata (reg_wdata ),
.reg_be (reg_be ),
.reg_rdata (reg_ws_rdata ),
.reg_ack (reg_ws_ack ),
.txd (ws_txd )
);
//----------------------------------------------------------------------
// Pinmux
//----------------------------------------------------------------------
pinmux u_pinmux (
.cfg_strap_pad_ctrl (cfg_strap_pad_ctrl ),
.pad_strap_in (pad_strap_in ),
// Digital IO
.digital_io_out (digital_io_out ),
.digital_io_oen (digital_io_oen ),
.digital_io_in (digital_io_in ),
.xtal_clk (xtal_clk ),
// Config
.cfg_gpio_out_type (cfg_gpio_out_type ),
.cfg_gpio_dir_sel (cfg_gpio_dir_sel ),
.cfg_multi_func_sel (cfg_multi_func_sel ),
.cfg_pwm_enb (cfg_pwm_enb ),
.pwm_wfm (pwm_wfm ),
.ext_intr_in (ext_intr_in ), // External PAD level interrupt
.pad_gpio_in (pad_gpio_in ), // GPIO data input from PAD
.pad_gpio_out (pad_gpio_out ), // GPIO Data out towards PAD
// SFLASH I/F
.sflash_sck (sflash_sck ),
.sflash_ss (sflash_ss ),
.sflash_oen (sflash_oen ),
.sflash_do (sflash_do ),
.sflash_di (sflash_di ),
// USB I/F
.usb_dp_o (usb_dp_o ),
.usb_dn_o (usb_dn_o ),
.usb_oen (usb_oen ),
.usb_dp_i (usb_dp_i ),
.usb_dn_i (usb_dn_i ),
// UART I/F
.uart_txd (uart_txd ),
.uart_rxd (uart_rxd ),
// I2CM I/F
.i2cm_clk_o (i2cm_clk_o ),
.i2cm_clk_i (i2cm_clk_i ),
.i2cm_clk_oen (i2cm_clk_oen ),
.i2cm_data_oen (i2cm_data_oen ),
.i2cm_data_o (i2cm_data_o ),
.i2cm_data_i (i2cm_data_i ),
// SPI MASTER
.spim_sck (spim_sck ),
.spim_ssn (spim_ssn ),
.spim_miso (spim_miso ),
.spim_mosi (spim_mosi ),
// SPI SLAVE
.spis_sck (spis_sck ),
.spis_ssn (spis_ssn ),
.spis_miso (spis_miso ),
.spis_mosi (spis_mosi ),
// UART MASTER I/F
.uartm_rxd (uartm_rxd ),
.uartm_txd (uartm_txd ),
.ws_txd (ws_txd ),
.dbg_clk_mon (dbg_clk_mon )
);
endmodule