arduino timer related clean-up
diff --git a/verilog/dv/agents/uart_agent.v b/verilog/dv/agents/uart_agent.v
index c9f11b4..2b12d64 100644
--- a/verilog/dv/agents/uart_agent.v
+++ b/verilog/dv/agents/uart_agent.v
@@ -144,8 +144,8 @@
reg parity;
begin
- data <= 8'h0;
- parity <= 1;
+ data = 8'h0;
+ parity = 1;
timeout_count = 0;
fork
@@ -162,15 +162,15 @@
// start cycle
@(negedge rxd)
disable loop_1;
- read <= 1;
+ read = 1;
// data cycle
@(posedge uart_rx_clk);
for (i = 0; i < data_bit_number; i = i + 1)
begin
@(posedge uart_rx_clk)
- data[i] <= rxd;
- parity <= parity ^ rxd;
+ data[i] = rxd;
+ parity = parity ^ rxd;
end
// parity cycle
@@ -207,7 +207,7 @@
end
end
- read <= 0;
+ read = 0;
-> uart_read_done;
if (expected_data != data)
@@ -239,8 +239,8 @@
reg parity;
begin
- data <= 8'h0;
- parity <= 1;
+ data = 8'h0;
+ parity = 1;
timeout_count = 0;
timeout = 0;
@@ -256,15 +256,15 @@
// start cycle
@(negedge rxd)
- read <= 1;
+ read = 1;
// data cycle
@(posedge uart_rx_clk );
for (i = 0; i < data_bit_number; i = i + 1)
begin
@(posedge uart_rx_clk)
- data[i] <= rxd;
- parity <= parity ^ rxd;
+ data[i] = rxd;
+ parity = parity ^ rxd;
end
// parity cycle
@@ -301,7 +301,7 @@
end
end
- read <= 0;
+ read = 0;
-> uart_read_done;
// $display ("(%m) Received Data %c", data);
@@ -331,8 +331,8 @@
reg parity;
begin
- data <= 8'h0;
- parity <= 1;
+ data = 8'h0;
+ parity = 1;
timeout_count = 0;
timeout = 0;
@@ -352,15 +352,15 @@
// start cycle
@(negedge rxd)
disable loop_1;
- read <= 1;
+ read = 1;
// data cycle
@(posedge uart_rx_clk);
for (i = 0; i < data_bit_number; i = i + 1)
begin
@(posedge uart_rx_clk)
- data[i] <= rxd;
- parity <= parity ^ rxd;
+ data[i] = rxd;
+ parity = parity ^ rxd;
end
// parity cycle
@@ -397,7 +397,7 @@
end
end
- read <= 0;
+ read = 0;
-> uart_read_done;
rxd_data = data;
@@ -424,8 +424,8 @@
reg parity;
begin
- data <= 8'h0;
- parity <= 1;
+ data = 8'h0;
+ parity = 1;
fork
@@ -433,15 +433,15 @@
// start cycle
@(negedge rxd)
- read <= 1;
+ read = 1;
// data cycle
@(posedge uart_rx_clk);
for (i = 0; i < data_bit_number; i = i + 1)
begin
@(posedge uart_rx_clk)
- data[i] <= rxd;
- parity <= parity ^ rxd;
+ data[i] = rxd;
+ parity = parity ^ rxd;
end
// parity cycle
@@ -478,7 +478,7 @@
end
end
- read <= 0;
+ read = 0;
-> uart_read_done;
rxd_data = data;
@@ -497,13 +497,13 @@
reg parity; // 0: odd parity, 1: even parity
begin
- parity <= #1 1;
+ parity = #1 1;
// start cycle
@(posedge uart_clk)
begin
- txd <= #1 0;
- write <= #1 1;
+ txd = #1 0;
+ write = #1 1;
end
// data cycle
@@ -511,8 +511,8 @@
for (i = 0; i < data_bit_number; i = i + 1)
begin
@(posedge uart_clk)
- txd <= #1 data[i];
- parity <= parity ^ data[i];
+ txd = #1 data[i];
+ parity = parity ^ data[i];
end
end
@@ -520,24 +520,24 @@
if (control_setup.parity_en)
begin
@(posedge uart_clk)
- txd <= #1
+ txd = #1
// control_setup.stick_parity ? ~control_setup.even_odd_parity :
control_setup.even_odd_parity ? !parity : parity;
end
// stop cycle 1
@(posedge uart_clk)
- txd <= #1 stop_err_check ? 0 : 1;
+ txd = #1 stop_err_check ? 0 : 1;
// stop cycle 2
@(posedge uart_clk);
- txd <= #1 1;
+ txd = #1 1;
if (data_bit_number == 5)
@(negedge uart_clk);
else if (control_setup.stop_bit_number)
@(posedge uart_clk);
- write <= #1 0;
+ write = #1 0;
if(debug_mode)
$display ("%m:... Write data %h to UART done cnt : %d ...\n", data,tx_count+1);
else
diff --git a/verilog/dv/arduino_timer_intr/Makefile b/verilog/dv/arduino_timer_intr/Makefile
new file mode 100644
index 0000000..aa946e0
--- /dev/null
+++ b/verilog/dv/arduino_timer_intr/Makefile
@@ -0,0 +1,144 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+# http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+
+# ---- Include Partitioned Makefiles ----
+
+CONFIG = caravel_user_project
+
+#######################################################################
+## Caravel Verilog for Integration Tests
+#######################################################################
+
+DESIGNS?=../../..
+TOOLS?=/opt/riscv32i/
+
+export USER_PROJECT_VERILOG ?= $(DESIGNS)/verilog
+export RISCDUINO_BOARD ?= $(USER_PROJECT_VERILOG)/dv/common/riscduino_board/custom_board/riscduino
+## YIFIVE FIRMWARE
+YIFIVE_FIRMWARE_PATH = $(USER_PROJECT_VERILOG)/dv/firmware
+GCC_PREFIX?=riscv32-unknown-elf
+
+
+## Simulation mode: RTL/GL
+SIM?=RTL
+DUMP?=OFF
+RISC_CORE?=0
+
+### To Enable IVERILOG FST DUMP
+export IVERILOG_DUMPER = fst
+
+
+.SUFFIXES:
+
+PATTERN = arduino_timer_intr
+
+all: ${PATTERN:=.vcd}
+
+
+vvp: ${PATTERN:=.vvp}
+
+%.vvp: %_tb.v
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${PATTERN}.ino.cpp -o ${PATTERN}.ino.cpp.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/Print.cpp -o Print.cpp.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WMath.cpp -o WMath.cpp.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WString.cpp -o WString.cpp.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WInterrupts.c -o WInterrupts.c.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/drivers/fe300prci/fe300prci_driver.c -o fe300prci_driver.c.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/abi.cpp -o abi.cpp.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/drivers/plic/plic_driver.c -o plic_driver.c.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/UARTClass.cpp -o UARTClass.cpp.o
+
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/TIMERClass.cpp -o TIMERClass.cpp.o
+
+ ${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/entry.S -o entry.S.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/hooks.c -o hooks.c.o
+ ${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/init.S -o init.S.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/itoa.c -o itoa.c.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/main.cpp -o main.cpp.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/malloc.c -o malloc.c.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/new.cpp -o new.cpp.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/sbrk.c -o sbrk.c.o
+ ${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/start.S -o start.S.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring.c -o wiring.c.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_analog.c -o wiring_analog.c.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_digital.c -o wiring_digital.c.o
+ ${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_pulse.cpp -o wiring_pulse.cpp.o
+ ${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_shift.c -o wiring_shift.c.o
+ ${GCC_PREFIX}-ar rcs core.a Print.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a UARTClass.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a TIMERClass.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a WInterrupts.c.o
+ ${GCC_PREFIX}-ar rcs core.a WMath.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a WString.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a abi.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a fe300prci_driver.c.o
+ ${GCC_PREFIX}-ar rcs core.a plic_driver.c.o
+ ${GCC_PREFIX}-ar rcs core.a entry.S.o
+ ${GCC_PREFIX}-ar rcs core.a hooks.c.o
+ ${GCC_PREFIX}-ar rcs core.a init.S.o
+ ${GCC_PREFIX}-ar rcs core.a itoa.c.o
+ ${GCC_PREFIX}-ar rcs core.a main.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a malloc.c.o
+ ${GCC_PREFIX}-ar rcs core.a new.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a sbrk.c.o
+ ${GCC_PREFIX}-ar rcs core.a start.S.o
+ ${GCC_PREFIX}-ar rcs core.a wiring.c.o
+ ${GCC_PREFIX}-ar rcs core.a wiring_analog.c.o
+ ${GCC_PREFIX}-ar rcs core.a wiring_digital.c.o
+ ${GCC_PREFIX}-ar rcs core.a wiring_pulse.cpp.o
+ ${GCC_PREFIX}-ar rcs core.a wiring_shift.c.o
+ ${GCC_PREFIX}-g++ -T ${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score/link.lds -nostartfiles -Wl,-N -Wl,--gc-sections -Wl,--wrap=malloc -Wl,--wrap=free -Wl,--wrap=sbrk ${PATTERN}.ino.cpp.o -nostdlib -Wl,--start-group core.a -lm -lstdc++ -lc -lgloss -Wl,--end-group -lgcc -o ${PATTERN}.ino.elf
+ ${GCC_PREFIX}-objcopy -R .rel.dyn -O binary ${PATTERN}.ino.elf ${PATTERN}.ino.bin
+ ${GCC_PREFIX}-objcopy -R .rel.dyn -O verilog ${PATTERN}.ino.elf ${PATTERN}.ino.hex
+ ${GCC_PREFIX}-objdump -D ${PATTERN}.ino.elf > ${PATTERN}.ino.dump
+ rm *.o *.a
+ifeq ($(SIM),RTL)
+ ifeq ($(DUMP),OFF)
+ iverilog -g2012 -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib \
+ $< -o $@
+ else
+ iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib \
+ $< -o $@
+ endif
+else
+ ifeq ($(DUMP),OFF)
+ iverilog -g2012 -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
+ $< -o $@
+ else
+ iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
+ $< -o $@
+ endif
+endif
+
+%.vcd: %.vvp
+ vvp $< +risc_core_id=$(RISC_CORE)
+
+
+# ---- Clean ----
+
+clean:
+ rm -f *.elf *.hex *.bin *.vvp *.vcd *.log *.dump *.a *.o
+
+.PHONY: clean hex all
diff --git a/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino b/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino
new file mode 100644
index 0000000..f38f333
--- /dev/null
+++ b/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino
@@ -0,0 +1,81 @@
+
+/*
+
+ Analog input, analog output, serial output
+
+ Reads an analog input pin, maps the result to a range from 0 to 255 and uses
+
+ the result to set the pulse width modulation (PWM) of an output pin.
+
+ Also prints the results to the Serial Monitor.
+
+ The circuit:
+
+ - potentiometer connected to analog pin 0.
+
+ Center pin of the potentiometer goes to the analog pin.
+
+ side pins of the potentiometer go to +5V and ground
+
+ - LED connected from digital pin 9 to ground
+
+ created 29 Dec. 2008
+
+ modified 9 Apr 2012
+
+ by Tom Igoe
+
+ This example code is in the public domain.
+
+ http://www.arduino.cc/en/Tutorial/AnalogInOutSerial
+
+*/
+
+#include"Arduino.h"
+// These constants won't change. They're used to give names to the pins used:
+
+
+int but1=2;
+int but2=3;
+
+
+int Timer_us =0;
+int Timer_ms =0;
+void setup() {
+
+ Timer.begin();
+ Timer.enable(0, TIMER_MICRO_STEP, 10); // 10 Micro Second
+ Timer.enable(1, TIMER_MILLI_STEP, 1); // 1 Milli Second
+ // initialize serial communications at 9600 bps:
+ Serial.begin(9600);
+ attachInterrupt(timerToInterrupt(0),timer_us_intr,RISING);
+ attachInterrupt(timerToInterrupt(1),timer_ms_intr,RISING);
+
+}
+
+void loop() {
+
+ delay(1);
+}
+
+
+void timer_us_intr()
+ {
+ Timer_us = Timer_us + 1;
+ if(Timer_us > 255) Timer_us = 0;;
+
+ Serial.print("Micro Second: ");
+ Serial.println(Timer_us);
+
+
+ }
+void timer_ms_intr()
+ {
+ Timer_ms = Timer_ms + 1;
+ if(Timer_ms > 255) Timer_ms = 0;;
+
+ Serial.print("Milli Second: ");
+ Serial.println(Timer_ms);
+
+
+ }
diff --git a/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino.cpp b/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino.cpp
new file mode 100644
index 0000000..d59053a
--- /dev/null
+++ b/verilog/dv/arduino_timer_intr/arduino_timer_intr.ino.cpp
@@ -0,0 +1,64 @@
+
+/*
+Testing the Timer Interrupt
+
+*/
+
+#include"Arduino.h"
+// These constants won't change. They're used to give names to the pins used:
+
+
+
+
+int Timer_us =0;
+int Timer_ms =0;
+void setup();
+void loop();
+void timer_us_intr();
+void timer_ms_intr();
+void setup() {
+
+ Timer.begin();
+ Timer.enable(0, TIMER_MICRO_STEP, 400); // 1000 Micro Second
+ Timer.enable(1, TIMER_MILLI_STEP, 2); // 2 Milli Second
+ // initialize serial communications at 9600 bps:
+ Serial.begin(1152000);
+ attachInterrupt(timerToInterrupt(0),timer_us_intr,RISING);
+ attachInterrupt(timerToInterrupt(1),timer_ms_intr,RISING);
+
+}
+
+void loop() {
+
+ delay(1);
+
+}
+
+
+void timer_us_intr()
+ {
+ Timer_us = Timer_us + 1;
+ if(Timer_us > 255) Timer_us = 0;;
+
+ Serial.print("Timer-0 Step: ");
+ Serial.println(Timer_us);
+ if(Timer_us > 19) {
+ Timer.disable(0);
+ }
+
+
+
+ }
+void timer_ms_intr()
+ {
+ Timer_ms = Timer_ms + 1;
+ if(Timer_ms > 255) Timer_ms = 0;;
+
+ Serial.print("Timer-1 Step: ");
+ Serial.println(Timer_ms);
+
+ if(Timer_ms > 4) {
+ Timer.disable(1);
+ }
+
+ }
diff --git a/verilog/dv/arduino_timer_intr/arduino_timer_intr_tb.v b/verilog/dv/arduino_timer_intr/arduino_timer_intr_tb.v
new file mode 100644
index 0000000..5e423d5
--- /dev/null
+++ b/verilog/dv/arduino_timer_intr/arduino_timer_intr_tb.v
@@ -0,0 +1,617 @@
+////////////////////////////////////////////////////////////////////////////
+// SPDX-FileCopyrightText: 2021 , Dinesh Annayya
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+// SPDX-FileContributor: Modified by Dinesh Annayya <dinesha@opencores.org>
+//////////////////////////////////////////////////////////////////////
+//// ////
+//// Standalone User validation Test bench ////
+//// ////
+//// This file is part of the riscdunio cores project ////
+//// https://github.com/dineshannayya/riscdunio.git ////
+//// ////
+//// Description ////
+//// This is a standalone test bench to validate the ////
+//// Digital core. ////
+//// This test bench to validate Arduino Interrupt ////
+//// ////
+//// To Do: ////
+//// nothing ////
+//// ////
+//// Author(s): ////
+//// - Dinesh Annayya, dinesh.annayya@gmail.com ////
+//// ////
+//// Revision : ////
+//// 0.1 - 29th July 2022, Dinesh A ////
+//// ////
+//////////////////////////////////////////////////////////////////////
+//// ////
+//// Copyright (C) 2000 Authors and OPENCORES.ORG ////
+//// ////
+//// This source file may be used and distributed without ////
+//// restriction provided that this copyright statement is not ////
+//// removed from the file and that any derivative work contains ////
+//// the original copyright notice and the associated disclaimer. ////
+//// ////
+//// This source file is free software; you can redistribute it ////
+//// and/or modify it under the terms of the GNU Lesser General ////
+//// Public License as published by the Free Software Foundation; ////
+//// either version 2.1 of the License, or (at your option) any ////
+//// later version. ////
+//// ////
+//// This source is distributed in the hope that it will be ////
+//// useful, but WITHOUT ANY WARRANTY; without even the implied ////
+//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR ////
+//// PURPOSE. See the GNU Lesser General Public License for more ////
+//// details. ////
+//// ////
+//// You should have received a copy of the GNU Lesser General ////
+//// Public License along with this source; if not, download it ////
+//// from http://www.opencores.org/lgpl.shtml ////
+//// ////
+//////////////////////////////////////////////////////////////////////
+
+`default_nettype wire
+
+`timescale 1 ns / 1 ns
+
+`include "sram_macros/sky130_sram_2kbyte_1rw1r_32x512_8.v"
+`include "uart_agent.v"
+
+`define TB_HEX "arduino_timer_intr.ino.hex"
+`define TB_TOP arduino_timer_intr_tb
+
+module `TB_TOP;
+ reg clock;
+ reg wb_rst_i;
+ reg power1, power2;
+ reg power3, power4;
+
+ reg wbd_ext_cyc_i; // strobe/request
+ reg wbd_ext_stb_i; // strobe/request
+ reg [31:0] wbd_ext_adr_i; // address
+ reg wbd_ext_we_i; // write
+ reg [31:0] wbd_ext_dat_i; // data output
+ reg [3:0] wbd_ext_sel_i; // byte enable
+
+ wire [31:0] wbd_ext_dat_o; // data input
+ wire wbd_ext_ack_o; // acknowlegement
+ wire wbd_ext_err_o; // error
+
+ // User I/O
+ wire [37:0] io_oeb;
+ wire [37:0] io_out;
+ wire [37:0] io_in;
+
+ wire gpio;
+ wire [37:0] mprj_io;
+ wire [7:0] mprj_io_0;
+ reg test_fail;
+ reg [31:0] read_data;
+ //----------------------------------
+ // Uart Configuration
+ // ---------------------------------
+ reg [1:0] uart_data_bit ;
+ reg uart_stop_bits ; // 0: 1 stop bit; 1: 2 stop bit;
+ reg uart_stick_parity ; // 1: force even parity
+ reg uart_parity_en ; // parity enable
+ reg uart_even_odd_parity ; // 0: odd parity; 1: even parity
+
+ reg [7:0] uart_data ;
+ reg [15:0] uart_divisor ; // divided by n * 16
+ reg [15:0] uart_timeout ;// wait time limit
+
+ reg [15:0] uart_rx_nu ;
+ reg [15:0] uart_tx_nu ;
+ reg [7:0] uart_write_data [0:39];
+ reg uart_fifo_enable ; // fifo mode disable
+ reg flag ;
+ reg compare_start ; // User Need to make sure that compare start match with RiscV core completing initial booting
+
+ reg [31:0] check_sum ;
+
+ integer d_risc_id;
+
+ integer i,j;
+
+
+
+
+ // 50Mhz CLock
+ always #10 clock <= (clock === 1'b0);
+
+ initial begin
+ clock = 0;
+ flag = 0;
+ compare_start = 0;
+ wbd_ext_cyc_i ='h0; // strobe/request
+ wbd_ext_stb_i ='h0; // strobe/request
+ wbd_ext_adr_i ='h0; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='h0; // data output
+ wbd_ext_sel_i ='h0; // byte enable
+ end
+
+ `ifdef WFDUMP
+ initial begin
+ $dumpfile("simx.vcd");
+ $dumpvars(3, `TB_TOP);
+ $dumpvars(0, `TB_TOP.u_top.u_riscv_top);
+ $dumpvars(0, `TB_TOP.u_top.u_pinmux);
+ $dumpvars(0, `TB_TOP.u_top.u_uart_i2c_usb_spi);
+ end
+ `endif
+
+
+ wire [15:0] irq_lines = u_top.u_pinmux.u_glbl_reg.irq_lines;
+
+
+/**********************************************************************
+ Arduino Digital PinMapping
+ ATMGA328 Pin No Functionality Arduino Pin Carvel Pin Mapping
+ Pin-2 PD0/RXD[0] 0 digital_io[1]
+ Pin-3 PD1/TXD[0] 1 digital_io[2]
+ Pin-4 PD2/RXD[1]/INT0 2 digital_io[3]
+ Pin-5 PD3/INT1/OC2B(PWM0) 3 digital_io[4]
+ Pin-6 PD4/TXD[1] 4 digital_io[5]
+ Pin-11 PD5/SS[3]/OC0B(PWM1)/T1 5 digital_io[8]
+ Pin-12 PD6/SS[2]/OC0A(PWM2)/AIN0 6 digital_io[9] /analog_io[2]
+ Pin-13 PD7/A1N1 7 digital_io[10]/analog_io[3]
+ Pin-14 PB0/CLKO/ICP1 8 digital_io[11]
+ Pin-15 PB1/SS[1]OC1A(PWM3) 9 digital_io[12]
+ Pin-16 PB2/SS[0]/OC1B(PWM4) 10 digital_io[13]
+ Pin-17 PB3/MOSI/OC2A(PWM5) 11 digital_io[14]
+ Pin-18 PB4/MISO 12 digital_io[15]
+ Pin-19 PB5/SCK 13 digital_io[16]
+
+ Pin-23 ADC0 14 digital_io[18]
+ Pin-24 ADC1 15 digital_io[19]
+ Pin-25 ADC2 16 digital_io[20]
+ Pin-26 ADC3 17 digital_io[21]
+ Pin-27 SDA 18 digital_io[22]
+ Pin-28 SCL 19 digital_io[23]
+
+ Pin-9 XTAL1 20 digital_io[6]
+ Pin-10 XTAL2 21 digital_io[7]
+ Pin-1 RESET 22 digital_io[0]
+*****************************************************************************/
+
+// Exclude UART TXD/RXD and RESET
+reg [21:2] arduino_din;
+assign {
+ //io_in[0], - Exclude RESET
+ io_in[7],
+ io_in[6],
+ io_in[23],
+ io_in[22],
+ io_in[21],
+ io_in[20],
+ io_in[19],
+ io_in[18],
+ io_in[16],
+ io_in[15],
+ io_in[14],
+ io_in[13],
+ io_in[12],
+ io_in[11],
+ io_in[10],
+ io_in[9],
+ io_in[8],
+ io_in[5],
+ io_in[4],
+ io_in[3]
+ // Uart pins io_in[2], io_in[1] are excluded
+ } = arduino_din;
+
+ /*************************************************************************
+ * This is Baud Rate to clock divider conversion for Test Bench
+ * Note: DUT uses 16x baud clock, where are test bench uses directly
+ * baud clock, Due to 16x Baud clock requirement at RTL, there will be
+ * some resolution loss, we expect at lower baud rate this resolution
+ * loss will be less. For Quick simulation perpose higher baud rate used
+ * *************************************************************************/
+ task tb_set_uart_baud;
+ input [31:0] ref_clk;
+ input [31:0] baud_rate;
+ output [31:0] baud_div;
+ reg [31:0] baud_div;
+ begin
+ // for 230400 Baud = (50Mhz/230400) = 216.7
+ baud_div = ref_clk/baud_rate; // Get the Bit Baud rate
+ // Baud 16x = 216/16 = 13
+ baud_div = baud_div/16; // To find the RTL baud 16x div value to find similar resolution loss in test bench
+ // Test bench baud clock , 16x of above value
+ // 13 * 16 = 208,
+ // (Note if you see original value was 216, now it's 208 )
+ baud_div = baud_div * 16;
+ // Test bench half cycle counter to toggle it
+ // 208/2 = 104
+ baud_div = baud_div/2;
+ //As counter run's from 0 , substract from 1
+ baud_div = baud_div-1;
+ end
+ endtask
+
+
+ reg[7:0] pinmap[0:22]; //ardiono to gpio pinmaping
+
+ initial begin
+ arduino_din[22:2] = 23'b010_1010_1010_1010_1010_10; // Initialise based on test case edge
+ pinmap[0] = 24;
+ pinmap[1] = 25;
+ pinmap[2] = 26;
+ pinmap[3] = 27;
+ pinmap[4] = 28;
+ pinmap[5] = 29;
+ pinmap[6] = 30;
+ pinmap[7] = 31;
+ pinmap[8] = 8;
+ pinmap[9] = 9;
+ pinmap[10] = 10;
+ pinmap[11] = 11;
+ pinmap[12] = 12;
+ pinmap[13] = 13;
+ pinmap[14] = 16;
+ pinmap[15] = 17;
+ pinmap[16] = 18;
+ pinmap[17] = 19;
+ pinmap[18] = 20;
+ pinmap[19] = 21;
+ pinmap[20] = 14;
+ pinmap[21] = 15;
+ pinmap[22] = 22;
+
+
+ uart_data_bit = 2'b11;
+ uart_stop_bits = 0; // 0: 1 stop bit; 1: 2 stop bit;
+ uart_stick_parity = 0; // 1: force even parity
+ uart_parity_en = 0; // parity enable
+ uart_even_odd_parity = 1; // 0: odd parity; 1: even parity
+ tb_set_uart_baud(50000000,1152000,uart_divisor);// 50Mhz Ref clock, Baud Rate: 230400
+ uart_timeout = 2000;// wait time limit
+ uart_fifo_enable = 0; // fifo mode disable
+
+ $value$plusargs("risc_core_id=%d", d_risc_id);
+
+ #200; // Wait for reset removal
+ repeat (10) @(posedge clock);
+ $display("Monitor: Standalone User Risc Boot Test Started");
+
+ // Remove Wb Reset
+ wb_user_core_write(`ADDR_SPACE_WBHOST+`WBHOST_GLBL_CFG,'h1);
+
+ repeat (2) @(posedge clock);
+ #1;
+ // Remove all the reset
+ if(d_risc_id == 0) begin
+ $display("STATUS: Working with Risc core 0");
+ wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h11F);
+ end else if(d_risc_id == 1) begin
+ $display("STATUS: Working with Risc core 1");
+ wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h21F);
+ end else if(d_risc_id == 2) begin
+ $display("STATUS: Working with Risc core 2");
+ wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h41F);
+ end else if(d_risc_id == 3) begin
+ $display("STATUS: Working with Risc core 3");
+ wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h81F);
+ end
+
+ repeat (100) @(posedge clock); // wait for Processor Get Ready
+
+ tb_uart.debug_mode = 0; // disable debug display
+ tb_uart.uart_init;
+ tb_uart.control_setup (uart_data_bit, uart_stop_bits, uart_parity_en, uart_even_odd_parity,
+ uart_stick_parity, uart_timeout, uart_divisor);
+
+ repeat (55000) @(posedge clock); // wait for Processor Get Ready
+ flag = 0;
+ check_sum = 0;
+ compare_start = 1;
+
+ fork
+
+ begin
+ while(flag == 0)
+ begin
+ tb_uart.read_char(read_data,flag);
+ if(flag == 0) begin
+ $write ("%c",read_data);
+ check_sum = check_sum+read_data;
+ end
+ end
+ end
+ begin
+ repeat (500000) @(posedge clock); // wait for Processor Get Ready
+ end
+ join_any
+
+ #1000
+ tb_uart.report_status(uart_rx_nu, uart_tx_nu);
+
+ test_fail = 0;
+
+ $display("Total Rx Char: %d Check Sum : %x ",uart_rx_nu, check_sum);
+ // Check
+ // if all the 102 byte received
+ // if no error
+ if(uart_rx_nu != 436) test_fail = 1;
+ if(check_sum != 32'h78cd) test_fail = 1;
+ if(tb_uart.err_cnt != 0) test_fail = 1;
+
+
+ $display("###################################################");
+ if(test_fail == 0) begin
+ `ifdef GL
+ $display("Monitor: Standalone String (GL) Passed");
+ `else
+ $display("Monitor: Standalone String (RTL) Passed");
+ `endif
+ end else begin
+ `ifdef GL
+ $display("Monitor: Standalone String (GL) Failed");
+ `else
+ $display("Monitor: Standalone String (RTL) Failed");
+ `endif
+ end
+ $display("###################################################");
+ $finish;
+ end
+
+ initial begin
+ wb_rst_i <= 1'b1;
+ #100;
+ wb_rst_i <= 1'b0; // Release reset
+ end
+wire USER_VDD1V8 = 1'b1;
+wire VSS = 1'b0;
+
+user_project_wrapper u_top(
+`ifdef USE_POWER_PINS
+ .vccd1(USER_VDD1V8), // User area 1 1.8V supply
+ .vssd1(VSS), // User area 1 digital ground
+`endif
+ .wb_clk_i (clock), // System clock
+ .user_clock2 (1'b1), // Real-time clock
+ .wb_rst_i (wb_rst_i), // Regular Reset signal
+
+ .wbs_cyc_i (wbd_ext_cyc_i), // strobe/request
+ .wbs_stb_i (wbd_ext_stb_i), // strobe/request
+ .wbs_adr_i (wbd_ext_adr_i), // address
+ .wbs_we_i (wbd_ext_we_i), // write
+ .wbs_dat_i (wbd_ext_dat_i), // data output
+ .wbs_sel_i (wbd_ext_sel_i), // byte enable
+
+ .wbs_dat_o (wbd_ext_dat_o), // data input
+ .wbs_ack_o (wbd_ext_ack_o), // acknowlegement
+
+
+ // Logic Analyzer Signals
+ .la_data_in ('1) ,
+ .la_data_out (),
+ .la_oenb ('0),
+
+
+ // IOs
+ .io_in (io_in) ,
+ .io_out (io_out) ,
+ .io_oeb (io_oeb) ,
+
+ .user_irq ()
+
+);
+// SSPI Slave I/F
+assign io_in[0] = 1'b1; // RESET
+//assign io_in[16] = 1'b0 ; // SPIS SCK
+
+`ifndef GL // Drive Power for Hold Fix Buf
+ // All standard cell need power hook-up for functionality work
+ initial begin
+
+ end
+`endif
+
+//------------------------------------------------------
+// Integrate the Serial flash with qurd support to
+// user core using the gpio pads
+// ----------------------------------------------------
+
+ wire flash_clk = io_out[24];
+ wire flash_csb = io_out[25];
+ // Creating Pad Delay
+ wire #1 io_oeb_29 = io_oeb[29];
+ wire #1 io_oeb_30 = io_oeb[30];
+ wire #1 io_oeb_31 = io_oeb[31];
+ wire #1 io_oeb_32 = io_oeb[32];
+ tri #1 flash_io0 = (io_oeb_29== 1'b0) ? io_out[29] : 1'bz;
+ tri #1 flash_io1 = (io_oeb_30== 1'b0) ? io_out[30] : 1'bz;
+ tri #1 flash_io2 = (io_oeb_31== 1'b0) ? io_out[31] : 1'bz;
+ tri #1 flash_io3 = (io_oeb_32== 1'b0) ? io_out[32] : 1'bz;
+
+ assign io_in[29] = flash_io0;
+ assign io_in[30] = flash_io1;
+ assign io_in[31] = flash_io2;
+ assign io_in[32] = flash_io3;
+
+ // Quard flash
+ s25fl256s #(.mem_file_name(`TB_HEX),
+ .otp_file_name("none"),
+ .TimingModel("S25FL512SAGMFI010_F_30pF"))
+ u_spi_flash_256mb (
+ // Data Inputs/Outputs
+ .SI (flash_io0),
+ .SO (flash_io1),
+ // Controls
+ .SCK (flash_clk),
+ .CSNeg (flash_csb),
+ .WPNeg (flash_io2),
+ .HOLDNeg (flash_io3),
+ .RSTNeg (!wb_rst_i)
+
+ );
+
+
+//---------------------------
+// UART Agent integration
+// --------------------------
+wire uart_txd,uart_rxd;
+
+assign uart_txd = io_out[2];
+assign io_in[1] = uart_rxd ;
+
+uart_agent tb_uart(
+ .mclk (clock ),
+ .txd (uart_rxd ),
+ .rxd (uart_txd )
+ );
+
+
+//----------------------------
+// All the task are defined here
+//----------------------------
+
+
+
+task wb_user_core_write;
+input [31:0] address;
+input [31:0] data;
+begin
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_adr_i =address; // address
+ wbd_ext_we_i ='h1; // write
+ wbd_ext_dat_i =data; // data output
+ wbd_ext_sel_i ='hF; // byte enable
+ wbd_ext_cyc_i ='h1; // strobe/request
+ wbd_ext_stb_i ='h1; // strobe/request
+ wait(wbd_ext_ack_o == 1);
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_cyc_i ='h0; // strobe/request
+ wbd_ext_stb_i ='h0; // strobe/request
+ wbd_ext_adr_i ='h0; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='h0; // data output
+ wbd_ext_sel_i ='h0; // byte enable
+ $display("DEBUG WB USER ACCESS WRITE Address : %x, Data : %x",address,data);
+ repeat (2) @(posedge clock);
+end
+endtask
+
+task wb_user_core_read;
+input [31:0] address;
+output [31:0] data;
+reg [31:0] data;
+begin
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_adr_i =address; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='0; // data output
+ wbd_ext_sel_i ='hF; // byte enable
+ wbd_ext_cyc_i ='h1; // strobe/request
+ wbd_ext_stb_i ='h1; // strobe/request
+ wait(wbd_ext_ack_o == 1);
+ repeat (1) @(negedge clock);
+ data = wbd_ext_dat_o;
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_cyc_i ='h0; // strobe/request
+ wbd_ext_stb_i ='h0; // strobe/request
+ wbd_ext_adr_i ='h0; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='h0; // data output
+ wbd_ext_sel_i ='h0; // byte enable
+ $display("DEBUG WB USER ACCESS READ Address : %x, Data : %x",address,data);
+ repeat (2) @(posedge clock);
+end
+endtask
+
+task wb_user_core_read_check;
+input [31:0] address;
+output [31:0] data;
+input [31:0] cmp_data;
+reg [31:0] data;
+begin
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_adr_i =address; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='0; // data output
+ wbd_ext_sel_i ='hF; // byte enable
+ wbd_ext_cyc_i ='h1; // strobe/request
+ wbd_ext_stb_i ='h1; // strobe/request
+ wait(wbd_ext_ack_o == 1);
+ repeat (1) @(negedge clock);
+ data = wbd_ext_dat_o;
+ repeat (1) @(posedge clock);
+ #1;
+ wbd_ext_cyc_i ='h0; // strobe/request
+ wbd_ext_stb_i ='h0; // strobe/request
+ wbd_ext_adr_i ='h0; // address
+ wbd_ext_we_i ='h0; // write
+ wbd_ext_dat_i ='h0; // data output
+ wbd_ext_sel_i ='h0; // byte enable
+ if(data !== cmp_data) begin
+ $display("ERROR : WB USER ACCESS READ Address : 0x%x, Exd: 0x%x Rxd: 0x%x ",address,cmp_data,data);
+ test_fail = 1;
+ end else begin
+ $display("STATUS: WB USER ACCESS READ Address : 0x%x, Data : 0x%x",address,data);
+ end
+ repeat (2) @(posedge clock);
+end
+endtask
+
+`ifdef GL
+
+wire wbd_spi_stb_i = u_top.u_qspi_master.wbd_stb_i;
+wire wbd_spi_ack_o = u_top.u_qspi_master.wbd_ack_o;
+wire wbd_spi_we_i = u_top.u_qspi_master.wbd_we_i;
+wire [31:0] wbd_spi_adr_i = u_top.u_qspi_master.wbd_adr_i;
+wire [31:0] wbd_spi_dat_i = u_top.u_qspi_master.wbd_dat_i;
+wire [31:0] wbd_spi_dat_o = u_top.u_qspi_master.wbd_dat_o;
+wire [3:0] wbd_spi_sel_i = u_top.u_qspi_master.wbd_sel_i;
+
+wire wbd_uart_stb_i = u_top.u_uart_i2c_usb_spi.reg_cs;
+wire wbd_uart_ack_o = u_top.u_uart_i2c_usb_spi.reg_ack;
+wire wbd_uart_we_i = u_top.u_uart_i2c_usb_spi.reg_wr;
+wire [8:0] wbd_uart_adr_i = u_top.u_uart_i2c_usb_spi.reg_addr;
+wire [7:0] wbd_uart_dat_i = u_top.u_uart_i2c_usb_spi.reg_wdata;
+wire [7:0] wbd_uart_dat_o = u_top.u_uart_i2c_usb_spi.reg_rdata;
+wire wbd_uart_sel_i = u_top.u_uart_i2c_usb_spi.reg_be;
+
+`endif
+
+/**
+`ifdef GL
+//-----------------------------------------------------------------------------
+// RISC IMEM amd DMEM Monitoring TASK
+//-----------------------------------------------------------------------------
+
+`define RISC_CORE user_uart_tb.u_top.u_core.u_riscv_top
+
+always@(posedge `RISC_CORE.wb_clk) begin
+ if(`RISC_CORE.wbd_imem_ack_i)
+ $display("RISCV-DEBUG => IMEM ADDRESS: %x Read Data : %x", `RISC_CORE.wbd_imem_adr_o,`RISC_CORE.wbd_imem_dat_i);
+ if(`RISC_CORE.wbd_dmem_ack_i && `RISC_CORE.wbd_dmem_we_o)
+ $display("RISCV-DEBUG => DMEM ADDRESS: %x Write Data: %x Resonse: %x", `RISC_CORE.wbd_dmem_adr_o,`RISC_CORE.wbd_dmem_dat_o);
+ if(`RISC_CORE.wbd_dmem_ack_i && !`RISC_CORE.wbd_dmem_we_o)
+ $display("RISCV-DEBUG => DMEM ADDRESS: %x READ Data : %x Resonse: %x", `RISC_CORE.wbd_dmem_adr_o,`RISC_CORE.wbd_dmem_dat_i);
+end
+
+`endif
+**/
+endmodule
+`include "s25fl256s.sv"
+`default_nettype wire
diff --git a/verilog/rtl/pinmux/src/pinmux_top.sv b/verilog/rtl/pinmux/src/pinmux_top.sv
index 02ecb2a..22dce38 100755
--- a/verilog/rtl/pinmux/src/pinmux_top.sv
+++ b/verilog/rtl/pinmux/src/pinmux_top.sv
@@ -60,7 +60,7 @@
output logic wbd_clk_pinmux,
// System Signals
// Inputs
- input logic mclk,
+ input logic mclk,
input logic h_reset_n,
// Global Reset control
@@ -72,7 +72,7 @@
output logic i2cm_rst_n ,
output logic usb_rst_n ,
- output logic [15:0] cfg_riscv_ctrl,
+ output logic [15:0] cfg_riscv_ctrl,
// Reg Bus Interface Signal
input logic reg_cs,
@@ -89,8 +89,8 @@
output logic [31:0] irq_lines,
output logic soft_irq,
output logic [2:0] user_irq,
- input logic usb_intr,
- input logic i2cm_intr,
+ input logic usb_intr,
+ input logic i2cm_intr,
// Digital IO
output logic [37:0] digital_io_out,
@@ -98,11 +98,11 @@
input logic [37:0] digital_io_in,
// SFLASH I/F
- input logic sflash_sck,
- input logic [3:0] sflash_ss,
- input logic [3:0] sflash_oen,
- input logic [3:0] sflash_do,
- output logic [3:0] sflash_di,
+ input logic sflash_sck,
+ input logic [3:0] sflash_ss,
+ input logic [3:0] sflash_oen,
+ input logic [3:0] sflash_do,
+ output logic [3:0] sflash_di,
// SSRAM I/F - Temp Masked
//input logic ssram_sck,
diff --git a/verilog/rtl/pinmux/src/timer_top.sv b/verilog/rtl/pinmux/src/timer_top.sv
index ae981dc..127d62f 100644
--- a/verilog/rtl/pinmux/src/timer_top.sv
+++ b/verilog/rtl/pinmux/src/timer_top.sv
@@ -132,7 +132,7 @@
timer u_timer_0
(
- .reset_n (sreset_n ),// system syn reset
+ .reset_n (h_reset_n ),// system syn reset
.mclk (mclk ),// master clock
.pulse_1us (pulse_1us ),
.pulse_1ms (pulse_1ms ),
@@ -152,7 +152,7 @@
wire [15:0] cfg_timer1_compare = cfg_timer1[15:0];
timer u_timer_1
(
- .reset_n (sreset_n ),// system syn reset
+ .reset_n (h_reset_n ),// system syn reset
.mclk (mclk ),// master clock
.pulse_1us (pulse_1us ),
.pulse_1ms (pulse_1ms ),
@@ -173,7 +173,7 @@
timer u_timer_2
(
- .reset_n (sreset_n ),// system syn reset
+ .reset_n (h_reset_n ),// system syn reset
.mclk (mclk ),// master clock
.pulse_1us (pulse_1us ),
.pulse_1ms (pulse_1ms ),
diff --git a/verilog/rtl/user_project_wrapper.v b/verilog/rtl/user_project_wrapper.v
index d3c9ec7..e54e37a 100644
--- a/verilog/rtl/user_project_wrapper.v
+++ b/verilog/rtl/user_project_wrapper.v
@@ -239,6 +239,7 @@
//// A. GPIO interrupt generation changed from 1 to 32 ////
//// B. Total interrupt to Riscv changed from 16 to 32 ////
//// C. uart_master disable option added at pinmux ////
+//// D. Timer interrupt related clean-up ////
//// ////
//////////////////////////////////////////////////////////////////////
//// ////
