blob: 25a20b4776e8e14623d385e817319a3f638ad578 [file] [log] [blame]
`default_nettype none
/*
* *-------------------------------------------------------------
* *
* * user_project_wrapper also incorporating an analog block
* *
* * This wrapper enumerates all of the pins available to
* the
* * user for the user project.
* *
* * An example user project is provided in
* this wrapper. The
* * example should be removed and replaced
* with the actual
* * user project.
* *
* *-------------------------------------------------------------
* * */
`ifndef MPRJ_IO_PADS
`define MPRJ_IO_PADS 38
`endif
module user_project_wrapper (
`ifdef USE_POWER_PINS
inout vdda1, // User area 1 3.3V supply
inout vdda2, // User area 2 3.3V supply
inout vssa1, // User area 1 analog ground
inout vssa2, // User area 2 analog ground
inout vccd1, // User area 1 1.8V supply
inout vccd2, // User area 2 1.8v supply
inout vssd1, // User area 1 digital ground
inout vssd2, // User area 2 digital ground
`endif
// Wishbone Slave ports (WB MI A)
input wb_clk_i,
input wb_rst_i,
input wbs_stb_i,
input wbs_cyc_i,
input wbs_we_i,
input [3:0] wbs_sel_i,
input [31:0] wbs_dat_i,
input [31:0] wbs_adr_i,
output wbs_ack_o,
output [31:0] wbs_dat_o,
// Logic Analyzer Signals
input [127:0] la_data_in,
output [127:0] la_data_out,
input [127:0] la_oenb,
// IOs
input [`MPRJ_IO_PADS-1:0] io_in,
output [`MPRJ_IO_PADS-1:0] io_out,
output [`MPRJ_IO_PADS-1:0] io_oeb,
// Analog (direct connection to GPIO pad---use with caution)
// Note that analog I/O is not available on the 7 lowest-numbered
// GPIO pads, and so the analog_io indexing is offset from the
// GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
inout [`MPRJ_IO_PADS-10:0] analog_io,
// Independent clock (on independent integer divider)
input user_clock2,
// User maskable interrupt signals
output [2:0] user_irq
);
/*--------------------------------------*/
/* User project is instantiated here */
/*--------------------------------------*/
user_proj_example user_proj_example_1 (
`ifdef USE_POWER_PINS
.vdda1(vdda1), // User area 1 3.3V supply
.vdda2(vdda2), // User area 2 3.3V supply
.vssa1(vssa1), // User area 1 analog ground
.vssa2(vssa2), // User area 2 analog ground
.vccd1(vccd1), // User area 1 1.8V supply
.vccd2(vccd2), // User area 2 1.8v supply
.vssd1(vssd1), // User area 1 digital ground
.vssd2(vssd2), // User area 2 digital ground
`endif
.wb_rst_i(wb_rst_i),
.wbs_stb_i(wbs_stb_i),
.wbs_cyc_i(wbs_cyc_i),
.wbs_we_i(wbs_we_i),
.wbs_sel_i(wbs_sel_i),
.wbs_dat_i(wbs_dat_i),
.wbs_adr_i(wbs_adr_i),
.wbs_ack_o(wbs_ack_o),
.wbs_dat_o(wbs_dat_o),
.la_data_in(la_data_in),
.la_data_out(la_data_out),
.la_oenb(la_oenb),
.io_in(io_in),
.io_out(io_out),
.io_oeb(io_oeb),
.user_irq(user_irq),
.user_clock2(user_clock2),
.analog_io(analog_io)
);
endmodule // user_project_wrapper
`default_nettype wire