blob: 73dd397e1d83cb0ee929da07332a9de768dde112 [file] [log] [blame]
/*
* SPDX-FileCopyrightText: 2020 Efabless Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
* SPDX-License-Identifier: Apache-2.0
*/
#include "../../defs.h"
// --------------------------------------------------------
/*
* GPIO Test
* Tests PU and PD on the lower 8 pins while being driven from outside
* Tests Writing to the upper 8 pins
* Tests reading from the lower 8 pins
*/
void main()
{
int i;
/* Set data out to zero */
reg_mprj_datal = 0;
/* Lower 8 pins are input and upper 8 pins are output */
reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
reg_mprj_io_23 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_22 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_21 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_20 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_19 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_18 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_17 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
reg_mprj_io_16 = GPIO_MODE_MGMT_STD_INPUT_NOPULL;
/* Apply configuration */
reg_mprj_xfer = 1;
while (reg_mprj_xfer == 1);
// change the pull up and pull down (checked by the TB)
reg_mprj_datal = 0xa0000000;
reg_mprj_io_23 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_22 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_21 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_20 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_19 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_18 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_17 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_16 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
/* Apply configuration */
reg_mprj_xfer = 1;
while (reg_mprj_xfer == 1);
reg_mprj_datal = 0x0b000000;
reg_mprj_io_23 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_22 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_21 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_20 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_19 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_18 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_17 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_16 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
/* Apply configuration */
reg_mprj_xfer = 1;
while (reg_mprj_xfer == 1);
reg_mprj_io_23 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_22 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_21 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_20 = GPIO_MODE_MGMT_STD_INPUT_PULLDOWN;
reg_mprj_io_19 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_18 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_17 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
reg_mprj_io_16 = GPIO_MODE_MGMT_STD_INPUT_PULLUP;
/* Apply configuration */
reg_mprj_xfer = 1;
while (reg_mprj_xfer == 1);
// read the lower 8 pins, add 1 then output the result
// checked by the TB
reg_mprj_datal = 0xab000000;
while (1){
int x = (reg_mprj_datal & 0xff0000) >> 16;
reg_mprj_datal = (x+1) << 24;
}
}