| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * user_project_wrapper |
| * |
| * This wrapper enumerates all of the pins available to the |
| * user for the user project. |
| * |
| * An example user project is provided in this wrapper. The |
| * example should be removed and replaced with the actual |
| * user project. |
| * |
| * THIS FILE HAS BEEN GENERATED USING multi_tools_project CODEGEN |
| * IF YOU NEED TO MAKE EDITS TO IT, EDIT codegen/caravel_iface_header.txt |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module user_project_wrapper #( |
| parameter BITS = 32 |
| )( |
| `ifdef USE_POWER_PINS |
| inout vdda1, // User area 1 3.3V supply |
| inout vdda2, // User area 2 3.3V supply |
| inout vssa1, // User area 1 analog ground |
| inout vssa2, // User area 2 analog ground |
| inout vccd1, // User area 1 1.8V supply |
| inout vccd2, // User area 2 1.8v supply |
| inout vssd1, // User area 1 digital ground |
| inout vssd2, // User area 2 digital ground |
| `endif |
| |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i, |
| input wb_rst_i, |
| input wbs_stb_i, |
| input wbs_cyc_i, |
| input wbs_we_i, |
| input [3:0] wbs_sel_i, |
| input [31:0] wbs_dat_i, |
| input [31:0] wbs_adr_i, |
| output wbs_ack_o, |
| output [31:0] wbs_dat_o, |
| |
| // Logic Analyzer Signals |
| input [127:0] la_data_in, |
| output [127:0] la_data_out, |
| input [127:0] la_oenb, |
| |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in, |
| output [`MPRJ_IO_PADS-1:0] io_out, |
| output [`MPRJ_IO_PADS-1:0] io_oeb, |
| |
| // Analog (direct connection to GPIO pad---use with caution) |
| // Note that analog I/O is not available on the 7 lowest-numbered |
| // GPIO pads, and so the analog_io indexing is offset from the |
| // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io). |
| inout [`MPRJ_IO_PADS-10:0] analog_io, |
| |
| // Independent clock (on independent integer divider) |
| input user_clock2, |
| |
| // User maskable interrupt signals |
| output [2:0] user_irq |
| ); |
| |
| |
| // generate active wires |
| wire [31: 0] active; |
| assign active = la_data_in[31:0]; |
| |
| // split remaining 96 logic analizer wires into 3 chunks |
| wire [31: 0] la1_data_in, la1_data_out, la1_oenb; |
| assign la1_data_in = la_data_in[63:32]; |
| assign la1_data_out = la_data_out[63:32]; |
| assign la1_oenb = la_oenb[63:32]; |
| |
| wire [31: 0] la2_data_in, la2_data_out, la2_oenb; |
| assign la2_data_in = la_data_in[95:64]; |
| assign la2_data_out = la_data_out[95:64]; |
| assign la2_oenb = la_oenb[95:64]; |
| |
| wire [31: 0] la3_data_in, la3_data_out, la3_oenb; |
| assign la3_data_in = la_data_in[127:96]; |
| assign la3_data_out = la_data_out[127:96]; |
| assign la3_oenb = la_oenb[127:96]; |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_0( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[0]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_1( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[1]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_2( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[2]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_3( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[3]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_4( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[4]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_5( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[5]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_6( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[6]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_7( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[7]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_8( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[8]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_9( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[9]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_10( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[10]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_11( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[11]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_12( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[12]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_frequency_counter wrapped_frequency_counter_13( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[13]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_vga_clock wrapped_vga_clock_14( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[14]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| wrapped_rgb_mixer wrapped_rgb_mixer_15( |
| `ifdef USE_POWER_PINS |
| .vccd1 (vccd1), |
| .vssd1 (vssd1), |
| `endif |
| .wb_clk_i (wb_clk_i), |
| .active (active[15]), |
| .la1_data_in (la1_data_in[31:0]), |
| .la1_data_out (la1_data_out[31:0]), |
| .la1_oenb (la1_oenb[31:0]), |
| .io_in (io_in[37:0]), |
| .io_out (io_out[37:0]), |
| .io_oeb (io_oeb[37:0]) |
| ); |
| |
| // end of module instantiation |
| |
| endmodule // user_project_wrapper |
| `default_nettype wire |