| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| |
| `timescale 1 ns / 1 ps |
| |
| `include "uprj_netlists.v" |
| `include "caravel_netlists.v" |
| `include "spiflash.v" |
| |
| module wb_port_tb; |
| reg clock; |
| reg RSTB; |
| reg CSB; |
| reg power1, power2; |
| reg power3, power4; |
| |
| wire gpio; |
| wire [37:0] mprj_io; |
| wire [7:0] mprj_io_0; |
| wire [15:0] checkbits; |
| |
| assign checkbits = mprj_io[31:16]; |
| |
| assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz; |
| |
| // External clock is used by default. Make this artificially fast for the |
| // simulation. Normally this would be a slow clock and the digital PLL |
| // would be the fast clock. |
| |
| always #12.5 clock <= (clock === 1'b0); |
| |
| initial begin |
| clock = 0; |
| end |
| |
| initial begin |
| $dumpfile("wb_port.vcd"); |
| $dumpvars(0, wb_port_tb); |
| |
| // Repeat cycles of 1000 clock edges as needed to complete testbench |
| repeat (30) begin |
| repeat (1000) @(posedge clock); |
| // $display("+1000 cycles"); |
| end |
| $display("%c[1;31m",27); |
| `ifdef GL |
| $display ("Monitor: Timeout, Test Mega-Project WB Port (GL) Failed"); |
| `else |
| $display ("Monitor: Timeout, Test Mega-Project WB Port (RTL) Failed"); |
| `endif |
| $display("%c[0m",27); |
| $finish; |
| end |
| |
| initial begin |
| wait(checkbits == 16'h AB60); |
| $display("Monitor: MPRJ-Logic WB Started"); |
| wait(checkbits == 16'h AB61); |
| `ifdef GL |
| $display("Monitor: Mega-Project WB (GL) Passed"); |
| `else |
| $display("Monitor: Mega-Project WB (RTL) Passed"); |
| `endif |
| $finish; |
| end |
| |
| initial begin |
| RSTB <= 1'b0; |
| CSB <= 1'b1; // Force CSB high |
| #2000; |
| RSTB <= 1'b1; // Release reset |
| #170000; |
| CSB = 1'b0; // CSB can be released |
| end |
| |
| initial begin // Power-up sequence |
| power1 <= 1'b0; |
| power2 <= 1'b0; |
| power3 <= 1'b0; |
| power4 <= 1'b0; |
| #100; |
| power1 <= 1'b1; |
| #100; |
| power2 <= 1'b1; |
| #100; |
| power3 <= 1'b1; |
| #100; |
| power4 <= 1'b1; |
| end |
| |
| always @(mprj_io) begin |
| #1 $display("MPRJ-IO state = %b ", mprj_io[7:0]); |
| end |
| |
| wire flash_csb; |
| wire flash_clk; |
| wire flash_io0; |
| wire flash_io1; |
| |
| wire VDD3V3 = power1; |
| wire VDD1V8 = power2; |
| wire USER_VDD3V3 = power3; |
| wire USER_VDD1V8 = power4; |
| wire VSS = 1'b0; |
| |
| caravel uut ( |
| .vddio (VDD3V3), |
| .vssio (VSS), |
| .vdda (VDD3V3), |
| .vssa (VSS), |
| .vccd (VDD1V8), |
| .vssd (VSS), |
| .vdda1 (USER_VDD3V3), |
| .vdda2 (USER_VDD3V3), |
| .vssa1 (VSS), |
| .vssa2 (VSS), |
| .vccd1 (USER_VDD1V8), |
| .vccd2 (USER_VDD1V8), |
| .vssd1 (VSS), |
| .vssd2 (VSS), |
| .clock (clock), |
| .gpio (gpio), |
| .mprj_io (mprj_io), |
| .flash_csb(flash_csb), |
| .flash_clk(flash_clk), |
| .flash_io0(flash_io0), |
| .flash_io1(flash_io1), |
| .resetb (RSTB) |
| ); |
| |
| spiflash #( |
| .FILENAME("wb_port.hex") |
| ) spiflash ( |
| .csb(flash_csb), |
| .clk(flash_clk), |
| .io0(flash_io0), |
| .io1(flash_io1), |
| .io2(), // not used |
| .io3() // not used |
| ); |
| |
| endmodule |
| `default_nettype wire |