Add files via upload
diff --git a/verilog/rtl/user_proj_example.v b/verilog/rtl/user_proj_example.v
new file mode 100644
index 0000000..eae4ab1
--- /dev/null
+++ b/verilog/rtl/user_proj_example.v
@@ -0,0 +1,95 @@
+// SPDX-FileCopyrightText: 2020 Efabless Corporation
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+
+`default_nettype none
+/*
+ *-------------------------------------------------------------
+ *
+ * user_proj_example
+ *
+ * This is an example of a (trivially simple) user project,
+ * showing how the user project can connect to the logic
+ * analyzer, the wishbone bus, and the I/O pads.
+ *
+ * This project generates an integer count, which is output
+ * on the user area GPIO pads (digital output only). The
+ * wishbone connection allows the project to be controlled
+ * (start and stop) from the management SoC program.
+ *
+ * See the testbenches in directory "mprj_counter" for the
+ * example programs that drive this user project. The three
+ * testbenches are "io_ports", "la_test1", and "la_test2".
+ *
+ *-------------------------------------------------------------
+ */
+
+module user_proj_example #(
+ parameter BITS = 32
+)(
+`ifdef USE_POWER_PINS
+ inout vdda1, // User area 1 3.3V supply
+ inout vdda2, // User area 2 3.3V supply
+ inout vssa1, // User area 1 analog ground
+ inout vssa2, // User area 2 analog ground
+ inout vccd1, // User area 1 1.8V supply
+ inout vccd2, // User area 2 1.8v supply
+ inout vssd1, // User area 1 digital ground
+ inout vssd2, // User area 2 digital ground
+`endif
+
+
+ // IOs
+ input in,
+ inout out
+);
+
+ avsdbgp_3v3_sky130_v2 #(
+ .BITS(BITS)
+ ) avsdbgp_3v3_sky130_v2 (
+ .EN(in),
+ .VBGP(out)
+ );
+
+endmodule
+
+module avsdbgp_3v3_sky130_v2 #(
+ parameter BITS = 32
+)(
+
+ input EN,
+ output VBGP
+
+);
+
+ reg real VBGP;
+
+ initial begin
+ if (EN == 1'b1) begin
+ VBGP <= 1.19;
+ end else begin
+ VBGP <= 0.0;
+ end
+ end
+
+ always @(EN) begin
+ if (EN == 1'b1) begin
+ VBGP <= 1.19;
+ end else begin
+ VBGP <= 0.0;
+ end
+ end
+
+endmodule
+`default_nettype wire
diff --git a/verilog/rtl/user_project_wrapper.v b/verilog/rtl/user_project_wrapper.v
new file mode 100644
index 0000000..7c42f8f
--- /dev/null
+++ b/verilog/rtl/user_project_wrapper.v
@@ -0,0 +1,108 @@
+// SPDX-FileCopyrightText: 2020 Efabless Corporation
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+// http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+
+`default_nettype none
+/*
+ *-------------------------------------------------------------
+ *
+ * user_project_wrapper
+ *
+ * This wrapper enumerates all of the pins available to the
+ * user for the user project.
+ *
+ * An example user project is provided in this wrapper. The
+ * example should be removed and replaced with the actual
+ * user project.
+ *
+ *-------------------------------------------------------------
+ */
+
+module user_project_wrapper #(
+ parameter BITS = 32
+) (
+`ifdef USE_POWER_PINS
+ inout vdda1, // User area 1 3.3V supply
+ inout vdda2, // User area 2 3.3V supply
+ inout vssa1, // User area 1 analog ground
+ inout vssa2, // User area 2 analog ground
+ inout vccd1, // User area 1 1.8V supply
+ inout vccd2, // User area 2 1.8v supply
+ inout vssd1, // User area 1 digital ground
+ inout vssd2, // User area 2 digital ground
+`endif
+
+ // Wishbone Slave ports (WB MI A)
+ input wb_clk_i,
+ input wb_rst_i,
+ input wbs_stb_i,
+ input wbs_cyc_i,
+ input wbs_we_i,
+ input [3:0] wbs_sel_i,
+ input [31:0] wbs_dat_i,
+ input [31:0] wbs_adr_i,
+ input gpio,
+ output wbs_ack_o,
+ output [31:0] wbs_dat_o,
+
+ // Logic Analyzer Signals
+ input [127:0] la_data_in,
+ output [127:0] la_data_out,
+ input [127:0] la_oenb,
+
+ // IOs
+ input [`MPRJ_IO_PADS-1:0] io_in,
+ output [`MPRJ_IO_PADS-1:0] io_out,
+ output [`MPRJ_IO_PADS-1:0] io_oeb,
+
+ // Analog (direct connection to GPIO pad---use with caution)
+ // Note that analog I/O is not available on the 7 lowest-numbered
+ // GPIO pads, and so the analog_io indexing is offset from the
+ // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
+ inout [`MPRJ_IO_PADS-10:0] analog_io,
+
+ // Independent clock (on independent integer divider)
+ input user_clock2,
+
+ // User maskable interrupt signals
+ output [2:0] user_irq
+);
+
+/*--------------------------------------*/
+/* User project is instantiated here */
+/*--------------------------------------*/
+
+
+user_proj_example mprj (
+ `ifdef USE_POWER_PINS
+ .vdda1(vdda1), // User area 1 3.3V power
+ .vdda2(vdda2), // User area 2 3.3V power
+ .vssa1(vssa1), // User area 1 analog ground
+ .vssa2(vssa2), // User area 2 analog ground
+ .vccd1(vccd1), // User area 1 1.8V power
+ .vccd2(vccd2), // User area 2 1.8V power
+ .vssd1(vssd1), // User area 1 digital ground
+ .vssd2(vssd2), // User area 2 digital ground
+ `endif
+
+
+ // IOs
+ .in(io_in[23]),
+ .out(io_out[16])
+
+ );
+
+endmodule // user_project_wrapper
+
+`default_nettype wire
