| |
| `timescale 1 ns / 1 ps |
| |
| `include "caravel.v" |
| `include "spiflash.v" |
| |
| module mprj_ctrl_tb; |
| reg clock; |
| |
| reg SDI, CSB, SCK, RSTB; |
| |
| wire [1:0] gpio; |
| wire flash_csb; |
| wire flash_clk; |
| wire flash_io0; |
| wire flash_io1; |
| wire flash_io2; |
| wire flash_io3; |
| wire SDO; |
| |
| // External clock is used by default. Make this artificially fast for the |
| // simulation. Normally this would be a slow clock and the digital PLL |
| // would be the fast clock. |
| |
| always #10 clock <= (clock === 1'b0); |
| |
| initial begin |
| clock = 0; |
| end |
| |
| initial begin |
| $dumpfile("mprj_ctrl_tb.vcd"); |
| $dumpvars(0, mprj_ctrl_tb); |
| repeat (25) begin |
| repeat (1000) @(posedge XCLK); |
| $display("+1000 cycles"); |
| end |
| $display("%c[1;31m",27); |
| $display ("Monitor: Timeout, Test Mega-Project (RTL) Failed"); |
| $display("%c[0m",27); |
| $finish; |
| end |
| |
| always @(gpio) begin |
| if(gpio == 16'hA040) begin |
| $display("Mega-Project control Test started"); |
| end |
| else if(gpio == 16'hAB40) begin |
| $display("%c[1;31m",27); |
| $display("Monitor: IO control R/W failed"); |
| $display("%c[0m",27); |
| $finish; |
| end |
| else if(gpio == 16'hAB41) begin |
| $display("Monitor: IO control R/W passed"); |
| end |
| else if(gpio == 16'hAB50) begin |
| $display("%c[1;31m",27); |
| $display("Monitor: power control R/W failed"); |
| $display("%c[0m",27); |
| $finish; |
| end else if(gpio == 16'hAB51) begin |
| $display("Monitor: power control R/W passed"); |
| $display("Monitor: Mega-Project control (RTL) test passed."); |
| $finish; |
| end |
| end |
| |
| initial begin |
| CSB <= 1'b1; |
| SCK <= 1'b0; |
| SDI <= 1'b0; |
| RSTB <= 1'b0; |
| #1000; |
| RSTB <= 1'b1; // Release reset |
| #2000; |
| CSB <= 1'b0; // Apply CSB to start transmission |
| end |
| |
| always @(gpio) begin |
| #1 $display("GPIO state = %b ", gpio); |
| end |
| |
| wire VDD3V3; |
| wire VDD1V8; |
| wire VSS; |
| |
| assign VSS = 1'b0; |
| assign VDD1V8 = 1'b1; |
| assign VDD3V3 = 1'b1; |
| |
| caravel uut ( |
| .vdd3v3 (VDD3V3), |
| .vdd1v8 (VDD1V8), |
| .vss (VSS), |
| .clock (clock), |
| .xclk (XCLK), |
| .SDI (SDI), |
| .SDO (SDO), |
| .CSB (CSB), |
| .SCK (SCK), |
| .ser_rx (1'b0), |
| .ser_tx (), |
| .irq (1'b0), |
| .gpio (gpio), |
| .flash_csb(flash_csb), |
| .flash_clk(flash_clk), |
| .flash_io0(flash_io0), |
| .flash_io1(flash_io1), |
| .flash_io2(flash_io2), |
| .flash_io3(flash_io3), |
| .RSTB (RSTB) |
| ); |
| |
| spiflash #( |
| .FILENAME("mprj_ctrl.hex") |
| ) spiflash ( |
| .csb(flash_csb), |
| .clk(flash_clk), |
| .io0(flash_io0), |
| .io1(flash_io1), |
| .io2(flash_io2), |
| .io3(flash_io3) |
| ); |
| |
| endmodule |