verilog/rtl/fwpayload/fwpayload.v

/****************************************************************************
 * fwpayload.v
 ****************************************************************************/
`include "wishbone_macros.svh"

`ifndef MPRJ_IO_PADS
	`define MPRJ_IO_PADS 38
`endif

/**
 * Module: fwpayload
 * 
 * Payload to go in Caravel
 *
 * - For simplicity, the IO's by and large mirror those of the user_project_wrapper
 */
module fwpayload(
		input			clock,
		input			sys_reset,
		input			core_reset,
		
		// Wishbone target port (mgmt interface)
		input 			wbs_stb_i,
		input 			wbs_cyc_i,
		input 			wbs_we_i,
		input [3:0] 	wbs_sel_i,
		input [31:0] 	wbs_dat_i,
		input [31:0] 	wbs_adr_i,
		output 			wbs_ack_o,
		output [31:0] 	wbs_dat_o,
		
		// LA Wishbone target
		input 			wba_stb_i,
		input 			wba_cyc_i,
		input 			wba_we_i,
		input [3:0] 	wba_sel_i,
		input [31:0] 	wba_dat_i,
		input [15:0] 	wba_adr_i,
		output 			wba_ack_o,
		output [31:0] 	wba_dat_o,
		
		// Monitor
		output[31:0]	pc,
		
		output			instr_complete,
		
		// Serial I/O
		output			ser_tx,
		input			ser_rx,
		
		input 			sdi,
		output 			csb,
		output 			sck,
		output 			sdo,
		output 			sdoenb,
		
		output[7:0]		gpio_out,
		input[7:0]		gpio_in,
		

		// Logic Analyzer Signals
		input  [127:0] 					la_data_in,
		output [127:0] 					la_data_out,
		input  [127:0] 					la_oen,

		// IOs
		input  [`MPRJ_IO_PADS-1:0] 			io_in,
		output [`MPRJ_IO_PADS-1:0] 			io_out,
		output [`MPRJ_IO_PADS-1:0] 			io_oeb
		);

`ifdef UNDEFINED
	// Clock/sys_reset control
	// Allow the logic analyzer to take control of clock/sys_reset
	wire clk = (~la_oen[127]) ? la_data_in[127]: wb_clk_i;
	wire rst = (~la_oen[126]) ? ~la_data_in[126]: wb_rst_i;
	wire core_rst = (~la_oen[125]) ? ~la_data_in[125]: wb_rst_i;
`endif

	/****************************************************************
	 * Interconnect definitions
	 ****************************************************************/
	// System interconnect
	localparam N_INITIATORS = 4;
	localparam INIT_ID_CORE_I = 0;
	localparam INIT_ID_CORE_D = 1;
	localparam INIT_ID_MGMT   = 2;
	localparam INIT_ID_LA     = 3;
	`WB_WIRES_ARR(i_ic_,32,32,N_INITIATORS);
	
	localparam N_TARGETS = 4;
	localparam TGT_ID_SRAM = 0;
	localparam TGT_ID_SPI  = 1;
	localparam TGT_ID_UART = 2;
	localparam TGT_ID_GPIO = 3;
	`WB_WIRES_ARR(ic_t_,32,32,N_TARGETS);
	
	// Memory map
	//
	// 28-bit address space, with the upper 4 bits masked
	//
	// 0x00000000..0x00000FFFF - Program/data memory
	// 0x01000000..0x010000000 - UART
	// 0x01000000..0x010000100 - SPI
	// 0x01000000..0x010000200 - GPIO
	
	// Interconnect
	wb_interconnect_NxN #(
			.WB_ADDR_WIDTH(32),
			.WB_DATA_WIDTH(32),
			.N_INITIATORS(N_INITIATORS),
			.N_TARGETS(N_TARGETS),
			.I_ADR_MASK({
				{ 32'h0F00_0000    },
				{ 32'h0FFF_FF00    },
				{ 32'h0FFF_FF00    },
				{ 32'h0FFF_FF00    }
				}),
			.T_ADR({
				{ 32'h0000_0000 },
				{ 32'h0100_0000 },
				{ 32'h0100_0100 },
				{ 32'h0100_0200 }
				})
		) u_ic (
			.clock(clock),
			.reset(sys_reset),
		
			`WB_CONNECT(,i_ic_),
			`WB_CONNECT(t,ic_t_)
		);

	/****************************************************************
	 * Connect management interface to the interconnect
	 ****************************************************************/
	assign i_ic_adr[32*INIT_ID_MGMT+:32] = wbs_adr_i;
	assign i_ic_dat_w[32*INIT_ID_MGMT+:32] = wbs_dat_i;
	assign wbs_dat_o = i_ic_dat_r[32*INIT_ID_MGMT+:32];
	assign i_ic_cyc[INIT_ID_MGMT] = wbs_cyc_i;
	assign i_ic_sel[4*INIT_ID_MGMT+:4] = wbs_sel_i;
	assign i_ic_stb[INIT_ID_MGMT] = wbs_stb_i;
	assign wbs_ack_o = i_ic_ack[INIT_ID_MGMT];
	assign i_ic_we[INIT_ID_MGMT] = wbs_we_i;
	
	/****************************************************************
	 * Connect logic-analyzer interface to the interconnect
	 ****************************************************************/
	assign i_ic_adr[32*INIT_ID_LA+:32] = wba_adr_i;
	assign i_ic_dat_w[32*INIT_ID_LA+:32] = wba_dat_i;
	assign wba_dat_o = i_ic_dat_r[32*INIT_ID_LA+:32];
	assign i_ic_cyc[INIT_ID_LA] = wba_cyc_i;
	assign i_ic_sel[4*INIT_ID_LA+:4] = wba_sel_i;
	assign i_ic_stb[INIT_ID_LA] = wba_stb_i;
	assign wba_ack_o = i_ic_ack[INIT_ID_LA];
	assign i_ic_we[INIT_ID_LA] = wba_we_i;
	
	
	/****************************************************************
	 * FWRISC instance
	 ****************************************************************/
	fwrisc_rv32i_wb u_core (
				.clock(clock),
				.reset(core_reset),

				`WB_CONNECT_ARR(wbi_,i_ic_,INIT_ID_CORE_I,32,32),
				`WB_CONNECT_ARR(wbd_,i_ic_,INIT_ID_CORE_D,32,32),
				.pc(pc),
				.instr_complete(instr_complete)
			);

`ifdef UNDEFINED
	// Probes
	// - PC 
	//   - [31:0] input
	// - instr_complete
	//   - [32]   input
	// - gpio_out
	//   - [39:36] input
	// - Clock and sys_reset
	//   - 127 output     - clock
	//   - 126 output     - sys_reset
	//   - 125 output     - core_reset
	localparam LA_CLOCK				= 127;
	localparam LA_RESET_SYS				= 126;
	localparam LA_RESET_CORE			= 125;
	localparam LA_GPIO_IN				= 40;
	localparam LA_GPIO_OUT				= 36;
	localparam LA_UART_RX				= 34;
	localparam LA_UART_TX				= 33;
	localparam LA_INSTR_COMPLETE        		= 32;
	localparam LA_PC      				= 0;
`endif
	
//	assign pc = u_core.u_core.u_core.pc;
//	assign instr_complete = u_core.u_core.u_core.instr_complete;

`ifdef UNDEFINED
	assign la_data_out[127:40] = 0;
	assign la_data_out[35] = 0;
	assign la_data_out[LA_PC+:32] = pc_probe;
	assign la_data_out[LA_INSTR_COMPLETE] = u_core.u_core.u_core.instr_complete;
`endif

	/****************************************************************
	 * Simple WB to SRAM bridge
	 ****************************************************************/
	reg[1:0] wb_bridge_state = 0;
	wire[31:0] sram_adr_i = ic_t_adr[32*TGT_ID_SRAM+:32];
	wire[31:0] sram_dat_w = ic_t_dat_w[32*TGT_ID_SRAM+:32];
	wire[31:0] sram_dat_r;
	assign ic_t_dat_r[32*TGT_ID_SRAM+:32] = sram_dat_r;
	wire       sram_cyc_i = ic_t_cyc[TGT_ID_SRAM];
	assign     ic_t_err[TGT_ID_SRAM] = 0;
	wire[3:0]  sram_sel_i = ic_t_sel[4*TGT_ID_SRAM+:4];
	wire       sram_stb_i = ic_t_stb[TGT_ID_SRAM];
	wire       sram_ack_o;
	assign     ic_t_ack[TGT_ID_SRAM] = sram_ack_o;
	wire       sram_we_i  = ic_t_we[TGT_ID_SRAM];
	
	always @(posedge clock) begin
		if (sys_reset == 1) begin
			wb_bridge_state <= 0;
		end else begin
			case (wb_bridge_state)
				0:
					if (sram_cyc_i && sram_stb_i) begin
						wb_bridge_state <= 1;
					end
				1:
					wb_bridge_state <= 2;
				2:
					wb_bridge_state <= 3;
				3:
					wb_bridge_state <= 0;
				default:
					wb_bridge_state <= 0;
			endcase
		end
	end
	
	/****************************************************************
	 * SRAM
	 ****************************************************************/
	spram_32x256 u_sram(
			.clock(clock),
			.a_adr(sram_adr_i),
			.a_dat_i(sram_dat_w),
			.a_dat_o(sram_dat_r),
			.a_we(sram_we_i),
			.a_sel(sram_sel_i));
	assign sram_ack_o = (wb_bridge_state == 3);
	
	/****************************************************************
	 * External interfaces
	 ****************************************************************/
	
	// - UART
	wire uart_enabled;
	simpleuart_wb #(
			.BASE_ADR(32'h0000_0000)
		) u_uart (
			.wb_clk_i(clock),
			.wb_rst_i(sys_reset),
			.wb_adr_i({24'b0, ic_t_adr[32*TGT_ID_UART+:8]}),
			.wb_dat_i(ic_t_dat_w[32*TGT_ID_UART+:32]),
			.wb_sel_i(ic_t_sel[4*TGT_ID_UART+:4]),
			.wb_we_i(ic_t_we[TGT_ID_UART]),
			.wb_cyc_i(ic_t_cyc[TGT_ID_UART]),
			.wb_stb_i(ic_t_stb[TGT_ID_UART]),
			.wb_ack_o(ic_t_ack[TGT_ID_UART]),
			.wb_dat_o(ic_t_dat_r[32*TGT_ID_UART+:32]),
			
			.uart_enabled(uart_enabled),
			.ser_tx(ser_tx),
			.ser_rx(ser_rx)
		);
	assign ic_t_err[TGT_ID_UART] = 0;
	
	// - SPI
	wire hk_connect;
	wire irq;
	simple_spi_master_wb #(
			.BASE_ADR(32'h0000_0000)
		) u_spi (
			.wb_clk_i(clock),
			.wb_rst_i(sys_reset),
			.wb_adr_i({24'b0, ic_t_adr[32*TGT_ID_SPI+:8]}),
			.wb_dat_i(ic_t_dat_w[32*TGT_ID_SPI+:32]),
			.wb_sel_i(ic_t_sel[4*TGT_ID_SPI+:4]),
			.wb_we_i(ic_t_we[TGT_ID_SPI]),
			.wb_cyc_i(ic_t_cyc[TGT_ID_SPI]),
			.wb_stb_i(ic_t_stb[TGT_ID_SPI]),
			.wb_ack_o(ic_t_ack[TGT_ID_SPI]),
			.wb_dat_o(ic_t_dat_r[32*TGT_ID_SPI+:32]),
			
			.hk_connect(hk_connect),
			.sdi(sdi),
			.csb(csb),
			.sck(sck),
			.sdo(sdo),
			.sdoenb(sdoenb),
			.irq(irq)
		);
	assign ic_t_err[TGT_ID_SPI] = 0;
	
	// - Simple GPIO
	reg[7:0]	gpio_out_r;
	assign gpio_out = gpio_out_r;
	
	wire[31:0] gpio_adr_i = ic_t_adr[32*TGT_ID_GPIO+:32];
	wire[31:0] gpio_dat_w = ic_t_dat_w[32*TGT_ID_GPIO+:32];
	wire[31:0] gpio_dat_r = {16'b0, gpio_in, gpio_out_r};
	assign ic_t_dat_r[32*TGT_ID_GPIO+:32] = gpio_dat_r;
	wire       gpio_cyc_i = ic_t_cyc[TGT_ID_GPIO];
	assign     ic_t_err[TGT_ID_GPIO] = 0;
	wire[3:0]  gpio_sel_i = ic_t_sel[4*TGT_ID_GPIO+:4];
	wire       gpio_stb_i = ic_t_stb[TGT_ID_GPIO];
	reg        gpio_ack_o;
	assign     ic_t_ack[TGT_ID_GPIO] = gpio_ack_o;
	wire       gpio_we_i  = ic_t_we[TGT_ID_GPIO];
	
	always @(posedge clock) begin
		if (sys_reset == 1) begin
			gpio_ack_o <= 1'b0;
			gpio_out_r <= 8'b0;
		end else begin
			gpio_ack_o <= (gpio_cyc_i && gpio_stb_i);
			
			if (gpio_cyc_i && gpio_stb_i && gpio_we_i) begin
				gpio_out_r <= gpio_dat_w[7:0];
			end
		end
	end	
	
	
	/****************************************************************
	 * Outputs
	 ****************************************************************/
`ifdef UNDEFINED
	// Tie unused pins
	assign io_out[11:0] = {12{1'b0}};
	assign io_oeb[11:0] = {12{1'b0}};

	// GPIO-o
	assign io_out[15:12] = gpio_out[3:0];
	assign io_oeb[15:12] = 4'hf;
	// UART
	assign io_out[16] = ser_tx;
	assign io_oeb[16] = 1;
	assign ser_rx = (~la_oen[LA_UART_RX])?la_data_in[LA_UART_RX]:io_in[17];
	assign io_oeb[17] = 0;
	
	assign sdi = io_in[18];
	assign io_oeb[18] = 0;
	assign io_out[19] = csb;
	assign io_oeb[19] = 1;
	assign io_out[20] = sck;
	assign io_oeb[20] = 1;
	assign io_out[21] = sdo;
	assign io_oeb[21] = 1;
	assign io_out[22] = sdoenb;
	assign io_oeb[22] = 1;

	// GPIO
	assign io_out[26:23] = gpio_out[7:4];
	assign io_oeb[26:23] = 4'hf;
	assign gpio_in[0] = (~la_oen[LA_GPIO_IN])?la_data_in[LA_GPIO_IN]:io_in[27+0];
	assign gpio_in[1] = (~la_oen[LA_GPIO_IN+1])?la_data_in[LA_GPIO_IN+1]:io_in[27+1];
	assign gpio_in[2] = (~la_oen[LA_GPIO_IN+2])?la_data_in[LA_GPIO_IN+2]:io_in[27+2];
	assign gpio_in[3] = (~la_oen[LA_GPIO_IN+3])?la_data_in[LA_GPIO_IN+3]:io_in[27+3];
	assign gpio_in[7:4] = io_in[34:31];
	assign io_oeb[34:27] = 4'h0;

	// Unused
	assign io_out[37:35] = {3{1'b0}};
	assign io_oeb[37:35] = {3{1'b0}};

	// Logic Analyzer I/O connections	
	// Probe the low bits of GPIO output with the LA
	assign la_data_out[LA_GPIO_OUT+:4] = gpio_out[3:0];
	assign gpio_in[3:0] = la_data_in[LA_GPIO_IN+:4];

	assign la_data_out[LA_UART_TX] = ser_tx;
`endif
	
endmodule