| `default_nettype none | |
| /* | |
| * PicoSoC - A simple example SoC using PicoRV32 | |
| * | |
| * Copyright (C) 2017 Clifford Wolf <clifford@clifford.at> | |
| * | |
| * Permission to use, copy, modify, and/or distribute this software for any | |
| * purpose with or without fee is hereby granted, provided that the above | |
| * copyright notice and this permission notice appear in all copies. | |
| * | |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES | |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR | |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES | |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN | |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF | |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. | |
| * | |
| */ | |
| `timescale 1 ns / 1 ps | |
| /* tbuart --- mimic an external UART display, operating at 9600 baud */ | |
| /* and accepting ASCII characters for display. */ | |
| /* To do: Match a known UART 3.3V 16x2 LCD display. However, it */ | |
| /* should be possible on a testing system to interface to the UART */ | |
| /* pins on a Raspberry Pi, also running at 3.3V. */ | |
| module tbuart ( | |
| input ser_rx | |
| ); | |
| reg [3:0] recv_state; | |
| reg [2:0] recv_divcnt; | |
| reg [7:0] recv_pattern; | |
| reg [8*50-1:0] recv_buf_data; // 50 characters. Increase as needed for tests. | |
| reg clk; | |
| initial begin | |
| clk <= 1'b0; | |
| recv_state <= 0; | |
| recv_divcnt <= 0; | |
| recv_pattern <= 0; | |
| recv_buf_data <= 0; | |
| end | |
| // NOTE: Running at 3.0us clock period @ 5 clocks per bit = 15.0us per | |
| // bit ~= 64 kbaud. Not tuned to any particular UART. Most run at | |
| // 9600 baud default and will bounce up to higher baud rates when | |
| // passed specific command words. | |
| always #1500 clk <= (clk === 1'b0); | |
| always @(posedge clk) begin | |
| recv_divcnt <= recv_divcnt + 1; | |
| case (recv_state) | |
| 0: begin | |
| if (!ser_rx) | |
| recv_state <= 1; | |
| recv_divcnt <= 0; | |
| end | |
| 1: begin | |
| if (2*recv_divcnt > 3'd3) begin | |
| recv_state <= 2; | |
| recv_divcnt <= 0; | |
| end | |
| end | |
| 10: begin | |
| if (recv_divcnt > 3'd3) begin | |
| // 0x0a = '\n' | |
| if (recv_pattern == 8'h0a) begin | |
| $display("output: %s", recv_buf_data); | |
| end else begin | |
| recv_buf_data <= {recv_buf_data, recv_pattern}; | |
| end | |
| recv_state <= 0; | |
| end | |
| end | |
| default: begin | |
| if (recv_divcnt > 3'd3) begin | |
| recv_pattern <= {ser_rx, recv_pattern[7:1]}; | |
| recv_state <= recv_state + 1; | |
| recv_divcnt <= 0; | |
| end | |
| end | |
| endcase | |
| end | |
| endmodule |