verilog/rtl/user_project_wrapper.v

// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *-------------------------------------------------------------
 *
 * user_project_wrapper
 *
 * This wrapper enumerates all of the pins available to the
 * user for the user project.
 *
 * An example user project is provided in this wrapper.  The
 * example should be removed and replaced with the actual
 * user project.
 *
 * THIS FILE HAS BEEN GENERATED USING multi_tools_project CODEGEN
 * IF YOU NEED TO MAKE EDITS TO IT, EDIT codegen/caravel_iface_header.txt
 *
 *-------------------------------------------------------------
 */

module user_project_wrapper #(
    parameter BITS = 32
)(
`ifdef USE_POWER_PINS
    inout vdda1,       // User area 1 3.3V supply
    inout vdda2,       // User area 2 3.3V supply
    inout vssa1,       // User area 1 analog ground
    inout vssa2,       // User area 2 analog ground
    inout vccd1,       // User area 1 1.8V supply
    inout vccd2,       // User area 2 1.8v supply
    inout vssd1,       // User area 1 digital ground
    inout vssd2,       // User area 2 digital ground
`endif

    // Wishbone Slave ports (WB MI A)
    input wb_clk_i,
    input wb_rst_i,
    input wbs_stb_i,
    input wbs_cyc_i,
    input wbs_we_i,
    input [3:0] wbs_sel_i,
    input [31:0] wbs_dat_i,
    input [31:0] wbs_adr_i,
    output wbs_ack_o,
    output [31:0] wbs_dat_o,

    // Logic Analyzer Signals
    input  [127:0] la_data_in,
    output [127:0] la_data_out,
    input  [127:0] la_oenb,

    // IOs
    input  [`MPRJ_IO_PADS-1:0] io_in,
    output [`MPRJ_IO_PADS-1:0] io_out,
    output [`MPRJ_IO_PADS-1:0] io_oeb,

    // Analog (direct connection to GPIO pad---use with caution)
    // Note that analog I/O is not available on the 7 lowest-numbered
    // GPIO pads, and so the analog_io indexing is offset from the
    // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
    inout [`MPRJ_IO_PADS-10:0] analog_io,

    // Independent clock (on independent integer divider)
    input   user_clock2,

    // User maskable interrupt signals
    output [2:0] user_irq
);

    // start of module instantiation

    wire sc_clk_out, sc_data_out, sc_latch_out, sc_scan_out;
    wire sc_clk_in,  sc_data_in;

    scan_controller #(.NUM_DESIGNS(250)) scan_controller (
       .clk                    (wb_clk_i),
       .reset                  (wb_rst_i),
       .active_select          (io_in[20:12]),
       .inputs                 (io_in[28:21]),
       .outputs                (io_out[36:29]),
       .ready                  (io_out[37]),
       .slow_clk               (io_out[10]),
       .set_clk_div            (io_in[11]),

       .scan_clk_out           (sc_clk_out),
       .scan_clk_in            (sc_clk_in),
       .scan_data_out          (sc_data_out),
       .scan_data_in           (sc_data_in),
       .scan_select            (sc_scan_out),
       .scan_latch_en          (sc_latch_out),

       .la_scan_clk_in         (la_data_in[0]),
       .la_scan_data_in        (la_data_in[1]),
       .la_scan_data_out       (la_data_out[0]),
       .la_scan_select         (la_data_in[2]),
       .la_scan_latch_en       (la_data_in[3]),

       .driver_sel             (io_in[9:8]),

       .oeb                    (io_oeb)
    );

    // [000] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_000_clk_out, sw_000_data_out, sw_000_scan_out, sw_000_latch_out;
    wire [7:0] sw_000_module_data_in;
    wire [7:0] sw_000_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_000 (
        .clk_in          (sc_clk_out),
        .data_in         (sc_data_out),
        .scan_select_in  (sc_scan_out),
        .latch_enable_in (sc_latch_out),
        .clk_out         (sw_000_clk_out),
        .data_out        (sw_000_data_out),
        .scan_select_out (sw_000_scan_out),
        .latch_enable_out(sw_000_latch_out),
        .module_data_in  (sw_000_module_data_in),
        .module_data_out (sw_000_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_000 (
        .io_in  (sw_000_module_data_in),
        .io_out (sw_000_module_data_out)
    );

    // [001] https://github.com/Fraserbc/tt02-simon
    wire sw_001_clk_out, sw_001_data_out, sw_001_scan_out, sw_001_latch_out;
    wire [7:0] sw_001_module_data_in;
    wire [7:0] sw_001_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_001 (
        .clk_in          (sw_000_clk_out),
        .data_in         (sw_000_data_out),
        .scan_select_in  (sw_000_scan_out),
        .latch_enable_in (sw_000_latch_out),
        .clk_out         (sw_001_clk_out),
        .data_out        (sw_001_data_out),
        .scan_select_out (sw_001_scan_out),
        .latch_enable_out(sw_001_latch_out),
        .module_data_in  (sw_001_module_data_in),
        .module_data_out (sw_001_module_data_out)
    );

    fraserbc_simon fraserbc_simon_001 (
        .io_in  (sw_001_module_data_in),
        .io_out (sw_001_module_data_out)
    );

    // [002] https://github.com/TomKeddie/tinytapeout-2022-2
    wire sw_002_clk_out, sw_002_data_out, sw_002_scan_out, sw_002_latch_out;
    wire [7:0] sw_002_module_data_in;
    wire [7:0] sw_002_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_002 (
        .clk_in          (sw_001_clk_out),
        .data_in         (sw_001_data_out),
        .scan_select_in  (sw_001_scan_out),
        .latch_enable_in (sw_001_latch_out),
        .clk_out         (sw_002_clk_out),
        .data_out        (sw_002_data_out),
        .scan_select_out (sw_002_scan_out),
        .latch_enable_out(sw_002_latch_out),
        .module_data_in  (sw_002_module_data_in),
        .module_data_out (sw_002_module_data_out)
    );

    tomkeddie_top_tto tomkeddie_top_tto_002 (
        .io_in  (sw_002_module_data_in),
        .io_out (sw_002_module_data_out)
    );

    // [003] https://github.com/chrisruk/matrixchip
    wire sw_003_clk_out, sw_003_data_out, sw_003_scan_out, sw_003_latch_out;
    wire [7:0] sw_003_module_data_in;
    wire [7:0] sw_003_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_003 (
        .clk_in          (sw_002_clk_out),
        .data_in         (sw_002_data_out),
        .scan_select_in  (sw_002_scan_out),
        .latch_enable_in (sw_002_latch_out),
        .clk_out         (sw_003_clk_out),
        .data_out        (sw_003_data_out),
        .scan_select_out (sw_003_scan_out),
        .latch_enable_out(sw_003_latch_out),
        .module_data_in  (sw_003_module_data_in),
        .module_data_out (sw_003_module_data_out)
    );

    chrisruk_matrix chrisruk_matrix_003 (
        .io_in  (sw_003_module_data_in),
        .io_out (sw_003_module_data_out)
    );

    // [004] https://github.com/loxodes/tt02-submission-loxodes
    wire sw_004_clk_out, sw_004_data_out, sw_004_scan_out, sw_004_latch_out;
    wire [7:0] sw_004_module_data_in;
    wire [7:0] sw_004_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_004 (
        .clk_in          (sw_003_clk_out),
        .data_in         (sw_003_data_out),
        .scan_select_in  (sw_003_scan_out),
        .latch_enable_in (sw_003_latch_out),
        .clk_out         (sw_004_clk_out),
        .data_out        (sw_004_data_out),
        .scan_select_out (sw_004_scan_out),
        .latch_enable_out(sw_004_latch_out),
        .module_data_in  (sw_004_module_data_in),
        .module_data_out (sw_004_module_data_out)
    );

    loxodes_sequencer loxodes_sequencer_004 (
        .io_in  (sw_004_module_data_in),
        .io_out (sw_004_module_data_out)
    );

    // [005] https://github.com/migcorre/tt02-dc
    wire sw_005_clk_out, sw_005_data_out, sw_005_scan_out, sw_005_latch_out;
    wire [7:0] sw_005_module_data_in;
    wire [7:0] sw_005_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_005 (
        .clk_in          (sw_004_clk_out),
        .data_in         (sw_004_data_out),
        .scan_select_in  (sw_004_scan_out),
        .latch_enable_in (sw_004_latch_out),
        .clk_out         (sw_005_clk_out),
        .data_out        (sw_005_data_out),
        .scan_select_out (sw_005_scan_out),
        .latch_enable_out(sw_005_latch_out),
        .module_data_in  (sw_005_module_data_in),
        .module_data_out (sw_005_module_data_out)
    );

    migcorre_pwm migcorre_pwm_005 (
        .io_in  (sw_005_module_data_in),
        .io_out (sw_005_module_data_out)
    );

    // [006] https://github.com/grayresearch/tt02-s4ga
    wire sw_006_clk_out, sw_006_data_out, sw_006_scan_out, sw_006_latch_out;
    wire [7:0] sw_006_module_data_in;
    wire [7:0] sw_006_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_006 (
        .clk_in          (sw_005_clk_out),
        .data_in         (sw_005_data_out),
        .scan_select_in  (sw_005_scan_out),
        .latch_enable_in (sw_005_latch_out),
        .clk_out         (sw_006_clk_out),
        .data_out        (sw_006_data_out),
        .scan_select_out (sw_006_scan_out),
        .latch_enable_out(sw_006_latch_out),
        .module_data_in  (sw_006_module_data_in),
        .module_data_out (sw_006_module_data_out)
    );

    s4ga s4ga_006 (
        .io_in  (sw_006_module_data_in),
        .io_out (sw_006_module_data_out)
    );

    // [007] https://github.com/ryancor/tt02-submission-template
    wire sw_007_clk_out, sw_007_data_out, sw_007_scan_out, sw_007_latch_out;
    wire [7:0] sw_007_module_data_in;
    wire [7:0] sw_007_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_007 (
        .clk_in          (sw_006_clk_out),
        .data_in         (sw_006_data_out),
        .scan_select_in  (sw_006_scan_out),
        .latch_enable_in (sw_006_latch_out),
        .clk_out         (sw_007_clk_out),
        .data_out        (sw_007_data_out),
        .scan_select_out (sw_007_scan_out),
        .latch_enable_out(sw_007_latch_out),
        .module_data_in  (sw_007_module_data_in),
        .module_data_out (sw_007_module_data_out)
    );

    alu_top alu_top_007 (
        .io_in  (sw_007_module_data_in),
        .io_out (sw_007_module_data_out)
    );

    // [008] https://github.com/AidanGood/tt02-McCoy
    wire sw_008_clk_out, sw_008_data_out, sw_008_scan_out, sw_008_latch_out;
    wire [7:0] sw_008_module_data_in;
    wire [7:0] sw_008_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_008 (
        .clk_in          (sw_007_clk_out),
        .data_in         (sw_007_data_out),
        .scan_select_in  (sw_007_scan_out),
        .latch_enable_in (sw_007_latch_out),
        .clk_out         (sw_008_clk_out),
        .data_out        (sw_008_data_out),
        .scan_select_out (sw_008_scan_out),
        .latch_enable_out(sw_008_latch_out),
        .module_data_in  (sw_008_module_data_in),
        .module_data_out (sw_008_module_data_out)
    );

    aidan_McCoy aidan_McCoy_008 (
        .io_in  (sw_008_module_data_in),
        .io_out (sw_008_module_data_out)
    );

    // [009] https://github.com/azdle/binary-clock-asic
    wire sw_009_clk_out, sw_009_data_out, sw_009_scan_out, sw_009_latch_out;
    wire [7:0] sw_009_module_data_in;
    wire [7:0] sw_009_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_009 (
        .clk_in          (sw_008_clk_out),
        .data_in         (sw_008_data_out),
        .scan_select_in  (sw_008_scan_out),
        .latch_enable_in (sw_008_latch_out),
        .clk_out         (sw_009_clk_out),
        .data_out        (sw_009_data_out),
        .scan_select_out (sw_009_scan_out),
        .latch_enable_out(sw_009_latch_out),
        .module_data_in  (sw_009_module_data_in),
        .module_data_out (sw_009_module_data_out)
    );

    azdle_binary_clock azdle_binary_clock_009 (
        .io_in  (sw_009_module_data_in),
        .io_out (sw_009_module_data_out)
    );

    // [010] https://github.com/justinP-wrk/tt02-TinySensor
    wire sw_010_clk_out, sw_010_data_out, sw_010_scan_out, sw_010_latch_out;
    wire [7:0] sw_010_module_data_in;
    wire [7:0] sw_010_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_010 (
        .clk_in          (sw_009_clk_out),
        .data_in         (sw_009_data_out),
        .scan_select_in  (sw_009_scan_out),
        .latch_enable_in (sw_009_latch_out),
        .clk_out         (sw_010_clk_out),
        .data_out        (sw_010_data_out),
        .scan_select_out (sw_010_scan_out),
        .latch_enable_out(sw_010_latch_out),
        .module_data_in  (sw_010_module_data_in),
        .module_data_out (sw_010_module_data_out)
    );

    user_module_347787021138264660 user_module_347787021138264660_010 (
        .io_in  (sw_010_module_data_in),
        .io_out (sw_010_module_data_out)
    );

    // [011] https://github.com/jar/tt02_sram
    wire sw_011_clk_out, sw_011_data_out, sw_011_scan_out, sw_011_latch_out;
    wire [7:0] sw_011_module_data_in;
    wire [7:0] sw_011_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_011 (
        .clk_in          (sw_010_clk_out),
        .data_in         (sw_010_data_out),
        .scan_select_in  (sw_010_scan_out),
        .latch_enable_in (sw_010_latch_out),
        .clk_out         (sw_011_clk_out),
        .data_out        (sw_011_data_out),
        .scan_select_out (sw_011_scan_out),
        .latch_enable_out(sw_011_latch_out),
        .module_data_in  (sw_011_module_data_in),
        .module_data_out (sw_011_module_data_out)
    );

    jar_sram_top jar_sram_top_011 (
        .io_in  (sw_011_module_data_in),
        .io_out (sw_011_module_data_out)
    );

    // [012] https://github.com/JensIMS/tt02-trafficlight
    wire sw_012_clk_out, sw_012_data_out, sw_012_scan_out, sw_012_latch_out;
    wire [7:0] sw_012_module_data_in;
    wire [7:0] sw_012_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_012 (
        .clk_in          (sw_011_clk_out),
        .data_in         (sw_011_data_out),
        .scan_select_in  (sw_011_scan_out),
        .latch_enable_in (sw_011_latch_out),
        .clk_out         (sw_012_clk_out),
        .data_out        (sw_012_data_out),
        .scan_select_out (sw_012_scan_out),
        .latch_enable_out(sw_012_latch_out),
        .module_data_in  (sw_012_module_data_in),
        .module_data_out (sw_012_module_data_out)
    );

    user_module_347690870424732244 user_module_347690870424732244_012 (
        .io_in  (sw_012_module_data_in),
        .io_out (sw_012_module_data_out)
    );

    // [013] https://github.com/svd321/tt02-Ising
    wire sw_013_clk_out, sw_013_data_out, sw_013_scan_out, sw_013_latch_out;
    wire [7:0] sw_013_module_data_in;
    wire [7:0] sw_013_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_013 (
        .clk_in          (sw_012_clk_out),
        .data_in         (sw_012_data_out),
        .scan_select_in  (sw_012_scan_out),
        .latch_enable_in (sw_012_latch_out),
        .clk_out         (sw_013_clk_out),
        .data_out        (sw_013_data_out),
        .scan_select_out (sw_013_scan_out),
        .latch_enable_out(sw_013_latch_out),
        .module_data_in  (sw_013_module_data_in),
        .module_data_out (sw_013_module_data_out)
    );

    user_module_347592305412145748 user_module_347592305412145748_013 (
        .io_in  (sw_013_module_data_in),
        .io_out (sw_013_module_data_out)
    );

    // [014] https://github.com/89Mods/tt2-AvalonSemi-5401
    wire sw_014_clk_out, sw_014_data_out, sw_014_scan_out, sw_014_latch_out;
    wire [7:0] sw_014_module_data_in;
    wire [7:0] sw_014_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_014 (
        .clk_in          (sw_013_clk_out),
        .data_in         (sw_013_data_out),
        .scan_select_in  (sw_013_scan_out),
        .latch_enable_in (sw_013_latch_out),
        .clk_out         (sw_014_clk_out),
        .data_out        (sw_014_data_out),
        .scan_select_out (sw_014_scan_out),
        .latch_enable_out(sw_014_latch_out),
        .module_data_in  (sw_014_module_data_in),
        .module_data_out (sw_014_module_data_out)
    );

    tholin_avalonsemi_5401 tholin_avalonsemi_5401_014 (
        .io_in  (sw_014_module_data_in),
        .io_out (sw_014_module_data_out)
    );

    // [015] https://github.com/RiceShelley/tiny-fft
    wire sw_015_clk_out, sw_015_data_out, sw_015_scan_out, sw_015_latch_out;
    wire [7:0] sw_015_module_data_in;
    wire [7:0] sw_015_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_015 (
        .clk_in          (sw_014_clk_out),
        .data_in         (sw_014_data_out),
        .scan_select_in  (sw_014_scan_out),
        .latch_enable_in (sw_014_latch_out),
        .clk_out         (sw_015_clk_out),
        .data_out        (sw_015_data_out),
        .scan_select_out (sw_015_scan_out),
        .latch_enable_out(sw_015_latch_out),
        .module_data_in  (sw_015_module_data_in),
        .module_data_out (sw_015_module_data_out)
    );

    tiny_fft tiny_fft_015 (
        .io_in  (sw_015_module_data_in),
        .io_out (sw_015_module_data_out)
    );

    // [016] https://github.com/moyesw/tt02-moyesw-StreamIntegrator
    wire sw_016_clk_out, sw_016_data_out, sw_016_scan_out, sw_016_latch_out;
    wire [7:0] sw_016_module_data_in;
    wire [7:0] sw_016_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_016 (
        .clk_in          (sw_015_clk_out),
        .data_in         (sw_015_data_out),
        .scan_select_in  (sw_015_scan_out),
        .latch_enable_in (sw_015_latch_out),
        .clk_out         (sw_016_clk_out),
        .data_out        (sw_016_data_out),
        .scan_select_out (sw_016_scan_out),
        .latch_enable_out(sw_016_latch_out),
        .module_data_in  (sw_016_module_data_in),
        .module_data_out (sw_016_module_data_out)
    );

    user_module_346553315158393428 user_module_346553315158393428_016 (
        .io_in  (sw_016_module_data_in),
        .io_out (sw_016_module_data_out)
    );

    // [017] https://github.com/Tschucker/tt02-submission-tiny-fir
    wire sw_017_clk_out, sw_017_data_out, sw_017_scan_out, sw_017_latch_out;
    wire [7:0] sw_017_module_data_in;
    wire [7:0] sw_017_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_017 (
        .clk_in          (sw_016_clk_out),
        .data_in         (sw_016_data_out),
        .scan_select_in  (sw_016_scan_out),
        .latch_enable_in (sw_016_latch_out),
        .clk_out         (sw_017_clk_out),
        .data_out        (sw_017_data_out),
        .scan_select_out (sw_017_scan_out),
        .latch_enable_out(sw_017_latch_out),
        .module_data_in  (sw_017_module_data_in),
        .module_data_out (sw_017_module_data_out)
    );

    user_module_347894637149553236 user_module_347894637149553236_017 (
        .io_in  (sw_017_module_data_in),
        .io_out (sw_017_module_data_out)
    );

    // [018] https://github.com/steieio/tt02-submission-universal-sr
    wire sw_018_clk_out, sw_018_data_out, sw_018_scan_out, sw_018_latch_out;
    wire [7:0] sw_018_module_data_in;
    wire [7:0] sw_018_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_018 (
        .clk_in          (sw_017_clk_out),
        .data_in         (sw_017_data_out),
        .scan_select_in  (sw_017_scan_out),
        .latch_enable_in (sw_017_latch_out),
        .clk_out         (sw_018_clk_out),
        .data_out        (sw_018_data_out),
        .scan_select_out (sw_018_scan_out),
        .latch_enable_out(sw_018_latch_out),
        .module_data_in  (sw_018_module_data_in),
        .module_data_out (sw_018_module_data_out)
    );

    user_module_346916357828248146 user_module_346916357828248146_018 (
        .io_in  (sw_018_module_data_in),
        .io_out (sw_018_module_data_out)
    );

    // [019] https://github.com/leardilap/tt02-LUTRAM
    wire sw_019_clk_out, sw_019_data_out, sw_019_scan_out, sw_019_latch_out;
    wire [7:0] sw_019_module_data_in;
    wire [7:0] sw_019_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_019 (
        .clk_in          (sw_018_clk_out),
        .data_in         (sw_018_data_out),
        .scan_select_in  (sw_018_scan_out),
        .latch_enable_in (sw_018_latch_out),
        .clk_out         (sw_019_clk_out),
        .data_out        (sw_019_data_out),
        .scan_select_out (sw_019_scan_out),
        .latch_enable_out(sw_019_latch_out),
        .module_data_in  (sw_019_module_data_in),
        .module_data_out (sw_019_module_data_out)
    );

    user_module_347594509754827347 user_module_347594509754827347_019 (
        .io_in  (sw_019_module_data_in),
        .io_out (sw_019_module_data_out)
    );

    // [020] https://github.com/ekliptik/tt02-chase-the-beat
    wire sw_020_clk_out, sw_020_data_out, sw_020_scan_out, sw_020_latch_out;
    wire [7:0] sw_020_module_data_in;
    wire [7:0] sw_020_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_020 (
        .clk_in          (sw_019_clk_out),
        .data_in         (sw_019_data_out),
        .scan_select_in  (sw_019_scan_out),
        .latch_enable_in (sw_019_latch_out),
        .clk_out         (sw_020_clk_out),
        .data_out        (sw_020_data_out),
        .scan_select_out (sw_020_scan_out),
        .latch_enable_out(sw_020_latch_out),
        .module_data_in  (sw_020_module_data_in),
        .module_data_out (sw_020_module_data_out)
    );

    chase_the_beat chase_the_beat_020 (
        .io_in  (sw_020_module_data_in),
        .io_out (sw_020_module_data_out)
    );

    // [021] https://github.com/maehw/tt02-bcd-7segment-encoder
    wire sw_021_clk_out, sw_021_data_out, sw_021_scan_out, sw_021_latch_out;
    wire [7:0] sw_021_module_data_in;
    wire [7:0] sw_021_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_021 (
        .clk_in          (sw_020_clk_out),
        .data_in         (sw_020_data_out),
        .scan_select_in  (sw_020_scan_out),
        .latch_enable_in (sw_020_latch_out),
        .clk_out         (sw_021_clk_out),
        .data_out        (sw_021_data_out),
        .scan_select_out (sw_021_scan_out),
        .latch_enable_out(sw_021_latch_out),
        .module_data_in  (sw_021_module_data_in),
        .module_data_out (sw_021_module_data_out)
    );

    user_module_347688030570545747 user_module_347688030570545747_021 (
        .io_in  (sw_021_module_data_in),
        .io_out (sw_021_module_data_out)
    );

    // [022] https://github.com/benevpi/tt02-LED-flasher
    wire sw_022_clk_out, sw_022_data_out, sw_022_scan_out, sw_022_latch_out;
    wire [7:0] sw_022_module_data_in;
    wire [7:0] sw_022_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_022 (
        .clk_in          (sw_021_clk_out),
        .data_in         (sw_021_data_out),
        .scan_select_in  (sw_021_scan_out),
        .latch_enable_in (sw_021_latch_out),
        .clk_out         (sw_022_clk_out),
        .data_out        (sw_022_data_out),
        .scan_select_out (sw_022_scan_out),
        .latch_enable_out(sw_022_latch_out),
        .module_data_in  (sw_022_module_data_in),
        .module_data_out (sw_022_module_data_out)
    );

    user_module_342981109408072274 user_module_342981109408072274_022 (
        .io_in  (sw_022_module_data_in),
        .io_out (sw_022_module_data_out)
    );

    // [023] https://github.com/kuriousd/tt02-4bit-multiplier
    wire sw_023_clk_out, sw_023_data_out, sw_023_scan_out, sw_023_latch_out;
    wire [7:0] sw_023_module_data_in;
    wire [7:0] sw_023_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_023 (
        .clk_in          (sw_022_clk_out),
        .data_in         (sw_022_data_out),
        .scan_select_in  (sw_022_scan_out),
        .latch_enable_in (sw_022_latch_out),
        .clk_out         (sw_023_clk_out),
        .data_out        (sw_023_data_out),
        .scan_select_out (sw_023_scan_out),
        .latch_enable_out(sw_023_latch_out),
        .module_data_in  (sw_023_module_data_in),
        .module_data_out (sw_023_module_data_out)
    );

    asic_multiplier_wrapper asic_multiplier_wrapper_023 (
        .io_in  (sw_023_module_data_in),
        .io_out (sw_023_module_data_out)
    );

    // [024] https://github.com/89Mods/tt2-avalonsemi-TBB1143
    wire sw_024_clk_out, sw_024_data_out, sw_024_scan_out, sw_024_latch_out;
    wire [7:0] sw_024_module_data_in;
    wire [7:0] sw_024_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_024 (
        .clk_in          (sw_023_clk_out),
        .data_in         (sw_023_data_out),
        .scan_select_in  (sw_023_scan_out),
        .latch_enable_in (sw_023_latch_out),
        .clk_out         (sw_024_clk_out),
        .data_out        (sw_024_data_out),
        .scan_select_out (sw_024_scan_out),
        .latch_enable_out(sw_024_latch_out),
        .module_data_in  (sw_024_module_data_in),
        .module_data_out (sw_024_module_data_out)
    );

    tholin_avalonsemi_tbb1143 tholin_avalonsemi_tbb1143_024 (
        .io_in  (sw_024_module_data_in),
        .io_out (sw_024_module_data_out)
    );

    // [025] https://github.com/TomKeddie/tinytapeout-2022-2a
    wire sw_025_clk_out, sw_025_data_out, sw_025_scan_out, sw_025_latch_out;
    wire [7:0] sw_025_module_data_in;
    wire [7:0] sw_025_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_025 (
        .clk_in          (sw_024_clk_out),
        .data_in         (sw_024_data_out),
        .scan_select_in  (sw_024_scan_out),
        .latch_enable_in (sw_024_latch_out),
        .clk_out         (sw_025_clk_out),
        .data_out        (sw_025_data_out),
        .scan_select_out (sw_025_scan_out),
        .latch_enable_out(sw_025_latch_out),
        .module_data_in  (sw_025_module_data_in),
        .module_data_out (sw_025_module_data_out)
    );

    tomkeddie_top_tto_a tomkeddie_top_tto_a_025 (
        .io_in  (sw_025_module_data_in),
        .io_out (sw_025_module_data_out)
    );

    // [026] https://github.com/mm21/tinytapeout2-led-matrix
    wire sw_026_clk_out, sw_026_data_out, sw_026_scan_out, sw_026_latch_out;
    wire [7:0] sw_026_module_data_in;
    wire [7:0] sw_026_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_026 (
        .clk_in          (sw_025_clk_out),
        .data_in         (sw_025_data_out),
        .scan_select_in  (sw_025_scan_out),
        .latch_enable_in (sw_025_latch_out),
        .clk_out         (sw_026_clk_out),
        .data_out        (sw_026_data_out),
        .scan_select_out (sw_026_scan_out),
        .latch_enable_out(sw_026_latch_out),
        .module_data_in  (sw_026_module_data_in),
        .module_data_out (sw_026_module_data_out)
    );

    mm21_LEDMatrixTop mm21_LEDMatrixTop_026 (
        .io_in  (sw_026_module_data_in),
        .io_out (sw_026_module_data_out)
    );

    // [027] https://github.com/argunda/tt02-TinyPFD
    wire sw_027_clk_out, sw_027_data_out, sw_027_scan_out, sw_027_latch_out;
    wire [7:0] sw_027_module_data_in;
    wire [7:0] sw_027_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_027 (
        .clk_in          (sw_026_clk_out),
        .data_in         (sw_026_data_out),
        .scan_select_in  (sw_026_scan_out),
        .latch_enable_in (sw_026_latch_out),
        .clk_out         (sw_027_clk_out),
        .data_out        (sw_027_data_out),
        .scan_select_out (sw_027_scan_out),
        .latch_enable_out(sw_027_latch_out),
        .module_data_in  (sw_027_module_data_in),
        .module_data_out (sw_027_module_data_out)
    );

    user_module_348195845106041428 user_module_348195845106041428_027 (
        .io_in  (sw_027_module_data_in),
        .io_out (sw_027_module_data_out)
    );

    // [028] https://github.com/meriac/loading-animation
    wire sw_028_clk_out, sw_028_data_out, sw_028_scan_out, sw_028_latch_out;
    wire [7:0] sw_028_module_data_in;
    wire [7:0] sw_028_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_028 (
        .clk_in          (sw_027_clk_out),
        .data_in         (sw_027_data_out),
        .scan_select_in  (sw_027_scan_out),
        .latch_enable_in (sw_027_latch_out),
        .clk_out         (sw_028_clk_out),
        .data_out        (sw_028_data_out),
        .scan_select_out (sw_028_scan_out),
        .latch_enable_out(sw_028_latch_out),
        .module_data_in  (sw_028_module_data_in),
        .module_data_out (sw_028_module_data_out)
    );

    user_module_348121131386929746 user_module_348121131386929746_028 (
        .io_in  (sw_028_module_data_in),
        .io_out (sw_028_module_data_out)
    );

    // [029] https://github.com/yubex/tt02-tiny_egg_timer
    wire sw_029_clk_out, sw_029_data_out, sw_029_scan_out, sw_029_latch_out;
    wire [7:0] sw_029_module_data_in;
    wire [7:0] sw_029_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_029 (
        .clk_in          (sw_028_clk_out),
        .data_in         (sw_028_data_out),
        .scan_select_in  (sw_028_scan_out),
        .latch_enable_in (sw_028_latch_out),
        .clk_out         (sw_029_clk_out),
        .data_out        (sw_029_data_out),
        .scan_select_out (sw_029_scan_out),
        .latch_enable_out(sw_029_latch_out),
        .module_data_in  (sw_029_module_data_in),
        .module_data_out (sw_029_module_data_out)
    );

    yubex_egg_timer yubex_egg_timer_029 (
        .io_in  (sw_029_module_data_in),
        .io_out (sw_029_module_data_out)
    );

    // [030] https://github.com/peppergrayxyz/Potato-1
    wire sw_030_clk_out, sw_030_data_out, sw_030_scan_out, sw_030_latch_out;
    wire [7:0] sw_030_module_data_in;
    wire [7:0] sw_030_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_030 (
        .clk_in          (sw_029_clk_out),
        .data_in         (sw_029_data_out),
        .scan_select_in  (sw_029_scan_out),
        .latch_enable_in (sw_029_latch_out),
        .clk_out         (sw_030_clk_out),
        .data_out        (sw_030_data_out),
        .scan_select_out (sw_030_scan_out),
        .latch_enable_out(sw_030_latch_out),
        .module_data_in  (sw_030_module_data_in),
        .module_data_out (sw_030_module_data_out)
    );

    xyz_peppergray_Potato1_top xyz_peppergray_Potato1_top_030 (
        .io_in  (sw_030_module_data_in),
        .io_out (sw_030_module_data_out)
    );

    // [031] https://github.com/zoent/tt02-zoe-chip
    wire sw_031_clk_out, sw_031_data_out, sw_031_scan_out, sw_031_latch_out;
    wire [7:0] sw_031_module_data_in;
    wire [7:0] sw_031_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_031 (
        .clk_in          (sw_030_clk_out),
        .data_in         (sw_030_data_out),
        .scan_select_in  (sw_030_scan_out),
        .latch_enable_in (sw_030_latch_out),
        .clk_out         (sw_031_clk_out),
        .data_out        (sw_031_data_out),
        .scan_select_out (sw_031_scan_out),
        .latch_enable_out(sw_031_latch_out),
        .module_data_in  (sw_031_module_data_in),
        .module_data_out (sw_031_module_data_out)
    );

    zoechip zoechip_031 (
        .io_in  (sw_031_module_data_in),
        .io_out (sw_031_module_data_out)
    );

    // [032] https://github.com/nanikgeorge/tt02-submission-template
    wire sw_032_clk_out, sw_032_data_out, sw_032_scan_out, sw_032_latch_out;
    wire [7:0] sw_032_module_data_in;
    wire [7:0] sw_032_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_032 (
        .clk_in          (sw_031_clk_out),
        .data_in         (sw_031_data_out),
        .scan_select_in  (sw_031_scan_out),
        .latch_enable_in (sw_031_latch_out),
        .clk_out         (sw_032_clk_out),
        .data_out        (sw_032_data_out),
        .scan_select_out (sw_032_scan_out),
        .latch_enable_out(sw_032_latch_out),
        .module_data_in  (sw_032_module_data_in),
        .module_data_out (sw_032_module_data_out)
    );

    user_module_348255968419643987 user_module_348255968419643987_032 (
        .io_in  (sw_032_module_data_in),
        .io_out (sw_032_module_data_out)
    );

    // [033] https://github.com/mbikovitsky/tt02-lfsr
    wire sw_033_clk_out, sw_033_data_out, sw_033_scan_out, sw_033_latch_out;
    wire [7:0] sw_033_module_data_in;
    wire [7:0] sw_033_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_033 (
        .clk_in          (sw_032_clk_out),
        .data_in         (sw_032_data_out),
        .scan_select_in  (sw_032_scan_out),
        .latch_enable_in (sw_032_latch_out),
        .clk_out         (sw_033_clk_out),
        .data_out        (sw_033_data_out),
        .scan_select_out (sw_033_scan_out),
        .latch_enable_out(sw_033_latch_out),
        .module_data_in  (sw_033_module_data_in),
        .module_data_out (sw_033_module_data_out)
    );

    mbikovitsky_top mbikovitsky_top_033 (
        .io_in  (sw_033_module_data_in),
        .io_out (sw_033_module_data_out)
    );

    // [034] https://github.com/teaandtechtime/tt02-submission-prbs15
    wire sw_034_clk_out, sw_034_data_out, sw_034_scan_out, sw_034_latch_out;
    wire [7:0] sw_034_module_data_in;
    wire [7:0] sw_034_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_034 (
        .clk_in          (sw_033_clk_out),
        .data_in         (sw_033_data_out),
        .scan_select_in  (sw_033_scan_out),
        .latch_enable_in (sw_033_latch_out),
        .clk_out         (sw_034_clk_out),
        .data_out        (sw_034_data_out),
        .scan_select_out (sw_034_scan_out),
        .latch_enable_out(sw_034_latch_out),
        .module_data_in  (sw_034_module_data_in),
        .module_data_out (sw_034_module_data_out)
    );

    user_module_348260124451668562 user_module_348260124451668562_034 (
        .io_in  (sw_034_module_data_in),
        .io_out (sw_034_module_data_out)
    );

    // [035] https://github.com/rolfmobile99/tt02-submission-template
    wire sw_035_clk_out, sw_035_data_out, sw_035_scan_out, sw_035_latch_out;
    wire [7:0] sw_035_module_data_in;
    wire [7:0] sw_035_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_035 (
        .clk_in          (sw_034_clk_out),
        .data_in         (sw_034_data_out),
        .scan_select_in  (sw_034_scan_out),
        .latch_enable_in (sw_034_latch_out),
        .clk_out         (sw_035_clk_out),
        .data_out        (sw_035_data_out),
        .scan_select_out (sw_035_scan_out),
        .latch_enable_out(sw_035_latch_out),
        .module_data_in  (sw_035_module_data_in),
        .module_data_out (sw_035_module_data_out)
    );

    rolfmobile99_alu_fsm_top rolfmobile99_alu_fsm_top_035 (
        .io_in  (sw_035_module_data_in),
        .io_out (sw_035_module_data_out)
    );

    // [036] https://github.com/jar/tt02_freespeech
    wire sw_036_clk_out, sw_036_data_out, sw_036_scan_out, sw_036_latch_out;
    wire [7:0] sw_036_module_data_in;
    wire [7:0] sw_036_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_036 (
        .clk_in          (sw_035_clk_out),
        .data_in         (sw_035_data_out),
        .scan_select_in  (sw_035_scan_out),
        .latch_enable_in (sw_035_latch_out),
        .clk_out         (sw_036_clk_out),
        .data_out        (sw_036_data_out),
        .scan_select_out (sw_036_scan_out),
        .latch_enable_out(sw_036_latch_out),
        .module_data_in  (sw_036_module_data_in),
        .module_data_out (sw_036_module_data_out)
    );

    jar_pi jar_pi_036 (
        .io_in  (sw_036_module_data_in),
        .io_out (sw_036_module_data_out)
    );

    // [037] https://github.com/alanvgreen/tt02-siren
    wire sw_037_clk_out, sw_037_data_out, sw_037_scan_out, sw_037_latch_out;
    wire [7:0] sw_037_module_data_in;
    wire [7:0] sw_037_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_037 (
        .clk_in          (sw_036_clk_out),
        .data_in         (sw_036_data_out),
        .scan_select_in  (sw_036_scan_out),
        .latch_enable_in (sw_036_latch_out),
        .clk_out         (sw_037_clk_out),
        .data_out        (sw_037_data_out),
        .scan_select_out (sw_037_scan_out),
        .latch_enable_out(sw_037_latch_out),
        .module_data_in  (sw_037_module_data_in),
        .module_data_out (sw_037_module_data_out)
    );

    user_module_348242239268323922 user_module_348242239268323922_037 (
        .io_in  (sw_037_module_data_in),
        .io_out (sw_037_module_data_out)
    );

    // [038] https://github.com/TheZoq2/smolfpga
    wire sw_038_clk_out, sw_038_data_out, sw_038_scan_out, sw_038_latch_out;
    wire [7:0] sw_038_module_data_in;
    wire [7:0] sw_038_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_038 (
        .clk_in          (sw_037_clk_out),
        .data_in         (sw_037_data_out),
        .scan_select_in  (sw_037_scan_out),
        .latch_enable_in (sw_037_latch_out),
        .clk_out         (sw_038_clk_out),
        .data_out        (sw_038_data_out),
        .scan_select_out (sw_038_scan_out),
        .latch_enable_out(sw_038_latch_out),
        .module_data_in  (sw_038_module_data_in),
        .module_data_out (sw_038_module_data_out)
    );

    thezoq2_yafpga thezoq2_yafpga_038 (
        .io_in  (sw_038_module_data_in),
        .io_out (sw_038_module_data_out)
    );

    // [039] https://github.com/moyesw/TT02-M0
    wire sw_039_clk_out, sw_039_data_out, sw_039_scan_out, sw_039_latch_out;
    wire [7:0] sw_039_module_data_in;
    wire [7:0] sw_039_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_039 (
        .clk_in          (sw_038_clk_out),
        .data_in         (sw_038_data_out),
        .scan_select_in  (sw_038_scan_out),
        .latch_enable_in (sw_038_latch_out),
        .clk_out         (sw_039_clk_out),
        .data_out        (sw_039_data_out),
        .scan_select_out (sw_039_scan_out),
        .latch_enable_out(sw_039_latch_out),
        .module_data_in  (sw_039_module_data_in),
        .module_data_out (sw_039_module_data_out)
    );

    moyes0_top_module moyes0_top_module_039 (
        .io_in  (sw_039_module_data_in),
        .io_out (sw_039_module_data_out)
    );

    // [040] https://github.com/yupferris/bitslam
    wire sw_040_clk_out, sw_040_data_out, sw_040_scan_out, sw_040_latch_out;
    wire [7:0] sw_040_module_data_in;
    wire [7:0] sw_040_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_040 (
        .clk_in          (sw_039_clk_out),
        .data_in         (sw_039_data_out),
        .scan_select_in  (sw_039_scan_out),
        .latch_enable_in (sw_039_latch_out),
        .clk_out         (sw_040_clk_out),
        .data_out        (sw_040_data_out),
        .scan_select_out (sw_040_scan_out),
        .latch_enable_out(sw_040_latch_out),
        .module_data_in  (sw_040_module_data_in),
        .module_data_out (sw_040_module_data_out)
    );

    yupferris_bitslam yupferris_bitslam_040 (
        .io_in  (sw_040_module_data_in),
        .io_out (sw_040_module_data_out)
    );

    // [041] https://github.com/ThorKn/tinytapeout02_pattern_player
    wire sw_041_clk_out, sw_041_data_out, sw_041_scan_out, sw_041_latch_out;
    wire [7:0] sw_041_module_data_in;
    wire [7:0] sw_041_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_041 (
        .clk_in          (sw_040_clk_out),
        .data_in         (sw_040_data_out),
        .scan_select_in  (sw_040_scan_out),
        .latch_enable_in (sw_040_latch_out),
        .clk_out         (sw_041_clk_out),
        .data_out        (sw_041_data_out),
        .scan_select_out (sw_041_scan_out),
        .latch_enable_out(sw_041_latch_out),
        .module_data_in  (sw_041_module_data_in),
        .module_data_out (sw_041_module_data_out)
    );

    user_module_341620484740219475 user_module_341620484740219475_041 (
        .io_in  (sw_041_module_data_in),
        .io_out (sw_041_module_data_out)
    );

    // [042] https://github.com/proppy/tt02-xls-popcount
    wire sw_042_clk_out, sw_042_data_out, sw_042_scan_out, sw_042_latch_out;
    wire [7:0] sw_042_module_data_in;
    wire [7:0] sw_042_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_042 (
        .clk_in          (sw_041_clk_out),
        .data_in         (sw_041_data_out),
        .scan_select_in  (sw_041_scan_out),
        .latch_enable_in (sw_041_latch_out),
        .clk_out         (sw_042_clk_out),
        .data_out        (sw_042_data_out),
        .scan_select_out (sw_042_scan_out),
        .latch_enable_out(sw_042_latch_out),
        .module_data_in  (sw_042_module_data_in),
        .module_data_out (sw_042_module_data_out)
    );

    github_com_proppy_tt02_xls_popcount github_com_proppy_tt02_xls_popcount_042 (
        .io_in  (sw_042_module_data_in),
        .io_out (sw_042_module_data_out)
    );

    // [043] https://github.com/jeanthom/tt02-rc5-receiver
    wire sw_043_clk_out, sw_043_data_out, sw_043_scan_out, sw_043_latch_out;
    wire [7:0] sw_043_module_data_in;
    wire [7:0] sw_043_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_043 (
        .clk_in          (sw_042_clk_out),
        .data_in         (sw_042_data_out),
        .scan_select_in  (sw_042_scan_out),
        .latch_enable_in (sw_042_latch_out),
        .clk_out         (sw_043_clk_out),
        .data_out        (sw_043_data_out),
        .scan_select_out (sw_043_scan_out),
        .latch_enable_out(sw_043_latch_out),
        .module_data_in  (sw_043_module_data_in),
        .module_data_out (sw_043_module_data_out)
    );

    rc5_top rc5_top_043 (
        .io_in  (sw_043_module_data_in),
        .io_out (sw_043_module_data_out)
    );

    // [044] https://github.com/mmolteni-secpat/tinytapeout02_chiDOM
    wire sw_044_clk_out, sw_044_data_out, sw_044_scan_out, sw_044_latch_out;
    wire [7:0] sw_044_module_data_in;
    wire [7:0] sw_044_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_044 (
        .clk_in          (sw_043_clk_out),
        .data_in         (sw_043_data_out),
        .scan_select_in  (sw_043_scan_out),
        .latch_enable_in (sw_043_latch_out),
        .clk_out         (sw_044_clk_out),
        .data_out        (sw_044_data_out),
        .scan_select_out (sw_044_scan_out),
        .latch_enable_out(sw_044_latch_out),
        .module_data_in  (sw_044_module_data_in),
        .module_data_out (sw_044_module_data_out)
    );

    user_module_341614374571475540 user_module_341614374571475540_044 (
        .io_in  (sw_044_module_data_in),
        .io_out (sw_044_module_data_out)
    );

    // [045] https://github.com/meriac/tt02-play-tune
    wire sw_045_clk_out, sw_045_data_out, sw_045_scan_out, sw_045_latch_out;
    wire [7:0] sw_045_module_data_in;
    wire [7:0] sw_045_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_045 (
        .clk_in          (sw_044_clk_out),
        .data_in         (sw_044_data_out),
        .scan_select_in  (sw_044_scan_out),
        .latch_enable_in (sw_044_latch_out),
        .clk_out         (sw_045_clk_out),
        .data_out        (sw_045_data_out),
        .scan_select_out (sw_045_scan_out),
        .latch_enable_out(sw_045_latch_out),
        .module_data_in  (sw_045_module_data_in),
        .module_data_out (sw_045_module_data_out)
    );

    meriac_tt02_play_tune meriac_tt02_play_tune_045 (
        .io_in  (sw_045_module_data_in),
        .io_out (sw_045_module_data_out)
    );

    // [046] https://github.com/phasenoisepon/tt02-phasenoisepon
    wire sw_046_clk_out, sw_046_data_out, sw_046_scan_out, sw_046_latch_out;
    wire [7:0] sw_046_module_data_in;
    wire [7:0] sw_046_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_046 (
        .clk_in          (sw_045_clk_out),
        .data_in         (sw_045_data_out),
        .scan_select_in  (sw_045_scan_out),
        .latch_enable_in (sw_045_latch_out),
        .clk_out         (sw_046_clk_out),
        .data_out        (sw_046_data_out),
        .scan_select_out (sw_046_scan_out),
        .latch_enable_out(sw_046_latch_out),
        .module_data_in  (sw_046_module_data_in),
        .module_data_out (sw_046_module_data_out)
    );

    phasenoisepon_seven_segment_seconds phasenoisepon_seven_segment_seconds_046 (
        .io_in  (sw_046_module_data_in),
        .io_out (sw_046_module_data_out)
    );

    // [047] https://github.com/13arn/tt02_counter_steamdeck
    wire sw_047_clk_out, sw_047_data_out, sw_047_scan_out, sw_047_latch_out;
    wire [7:0] sw_047_module_data_in;
    wire [7:0] sw_047_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_047 (
        .clk_in          (sw_046_clk_out),
        .data_in         (sw_046_data_out),
        .scan_select_in  (sw_046_scan_out),
        .latch_enable_in (sw_046_latch_out),
        .clk_out         (sw_047_clk_out),
        .data_out        (sw_047_data_out),
        .scan_select_out (sw_047_scan_out),
        .latch_enable_out(sw_047_latch_out),
        .module_data_in  (sw_047_module_data_in),
        .module_data_out (sw_047_module_data_out)
    );

    user_module_341541108650607187 user_module_341541108650607187_047 (
        .io_in  (sw_047_module_data_in),
        .io_out (sw_047_module_data_out)
    );

    // [048] https://github.com/ThorKn/tinytapeout02_shiftregister_challenge
    wire sw_048_clk_out, sw_048_data_out, sw_048_scan_out, sw_048_latch_out;
    wire [7:0] sw_048_module_data_in;
    wire [7:0] sw_048_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_048 (
        .clk_in          (sw_047_clk_out),
        .data_in         (sw_047_data_out),
        .scan_select_in  (sw_047_scan_out),
        .latch_enable_in (sw_047_latch_out),
        .clk_out         (sw_048_clk_out),
        .data_out        (sw_048_data_out),
        .scan_select_out (sw_048_scan_out),
        .latch_enable_out(sw_048_latch_out),
        .module_data_in  (sw_048_module_data_in),
        .module_data_out (sw_048_module_data_out)
    );

    user_module_341516949939814994 user_module_341516949939814994_048 (
        .io_in  (sw_048_module_data_in),
        .io_out (sw_048_module_data_out)
    );

    // [049] https://github.com/89Mods/tt2-4x4-multiply
    wire sw_049_clk_out, sw_049_data_out, sw_049_scan_out, sw_049_latch_out;
    wire [7:0] sw_049_module_data_in;
    wire [7:0] sw_049_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_049 (
        .clk_in          (sw_048_clk_out),
        .data_in         (sw_048_data_out),
        .scan_select_in  (sw_048_scan_out),
        .latch_enable_in (sw_048_latch_out),
        .clk_out         (sw_049_clk_out),
        .data_out        (sw_049_data_out),
        .scan_select_out (sw_049_scan_out),
        .latch_enable_out(sw_049_latch_out),
        .module_data_in  (sw_049_module_data_in),
        .module_data_out (sw_049_module_data_out)
    );

    tt2_tholin_multiplier tt2_tholin_multiplier_049 (
        .io_in  (sw_049_module_data_in),
        .io_out (sw_049_module_data_out)
    );

    // [050] https://github.com/89Mods/tt2-multiplexed-counter
    wire sw_050_clk_out, sw_050_data_out, sw_050_scan_out, sw_050_latch_out;
    wire [7:0] sw_050_module_data_in;
    wire [7:0] sw_050_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_050 (
        .clk_in          (sw_049_clk_out),
        .data_in         (sw_049_data_out),
        .scan_select_in  (sw_049_scan_out),
        .latch_enable_in (sw_049_latch_out),
        .clk_out         (sw_050_clk_out),
        .data_out        (sw_050_data_out),
        .scan_select_out (sw_050_scan_out),
        .latch_enable_out(sw_050_latch_out),
        .module_data_in  (sw_050_module_data_in),
        .module_data_out (sw_050_module_data_out)
    );

    tt2_tholin_multiplexed_counter tt2_tholin_multiplexed_counter_050 (
        .io_in  (sw_050_module_data_in),
        .io_out (sw_050_module_data_out)
    );

    // [051] https://github.com/proppy/tt02-xls-counter
    wire sw_051_clk_out, sw_051_data_out, sw_051_scan_out, sw_051_latch_out;
    wire [7:0] sw_051_module_data_in;
    wire [7:0] sw_051_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_051 (
        .clk_in          (sw_050_clk_out),
        .data_in         (sw_050_data_out),
        .scan_select_in  (sw_050_scan_out),
        .latch_enable_in (sw_050_latch_out),
        .clk_out         (sw_051_clk_out),
        .data_out        (sw_051_data_out),
        .scan_select_out (sw_051_scan_out),
        .latch_enable_out(sw_051_latch_out),
        .module_data_in  (sw_051_module_data_in),
        .module_data_out (sw_051_module_data_out)
    );

    github_com_proppy_tt02_xls_counter github_com_proppy_tt02_xls_counter_051 (
        .io_in  (sw_051_module_data_in),
        .io_out (sw_051_module_data_out)
    );

    // [052] https://github.com/QuantamHD/ethan-evan-random-numbers
    wire sw_052_clk_out, sw_052_data_out, sw_052_scan_out, sw_052_latch_out;
    wire [7:0] sw_052_module_data_in;
    wire [7:0] sw_052_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_052 (
        .clk_in          (sw_051_clk_out),
        .data_in         (sw_051_data_out),
        .scan_select_in  (sw_051_scan_out),
        .latch_enable_in (sw_051_latch_out),
        .clk_out         (sw_052_clk_out),
        .data_out        (sw_052_data_out),
        .scan_select_out (sw_052_scan_out),
        .latch_enable_out(sw_052_latch_out),
        .module_data_in  (sw_052_module_data_in),
        .module_data_out (sw_052_module_data_out)
    );

    xor_shift32_quantamhd xor_shift32_quantamhd_052 (
        .io_in  (sw_052_module_data_in),
        .io_out (sw_052_module_data_out)
    );

    // [053] https://github.com/QuantamHD/evan-submission
    wire sw_053_clk_out, sw_053_data_out, sw_053_scan_out, sw_053_latch_out;
    wire [7:0] sw_053_module_data_in;
    wire [7:0] sw_053_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_053 (
        .clk_in          (sw_052_clk_out),
        .data_in         (sw_052_data_out),
        .scan_select_in  (sw_052_scan_out),
        .latch_enable_in (sw_052_latch_out),
        .clk_out         (sw_053_clk_out),
        .data_out        (sw_053_data_out),
        .scan_select_out (sw_053_scan_out),
        .latch_enable_out(sw_053_latch_out),
        .module_data_in  (sw_053_module_data_in),
        .module_data_out (sw_053_module_data_out)
    );

    xor_shift32_evango xor_shift32_evango_053 (
        .io_in  (sw_053_module_data_in),
        .io_out (sw_053_module_data_out)
    );

    // [054] https://github.com/FlyGoat/tt02-play-tune-flygoat
    wire sw_054_clk_out, sw_054_data_out, sw_054_scan_out, sw_054_latch_out;
    wire [7:0] sw_054_module_data_in;
    wire [7:0] sw_054_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_054 (
        .clk_in          (sw_053_clk_out),
        .data_in         (sw_053_data_out),
        .scan_select_in  (sw_053_scan_out),
        .latch_enable_in (sw_053_latch_out),
        .clk_out         (sw_054_clk_out),
        .data_out        (sw_054_data_out),
        .scan_select_out (sw_054_scan_out),
        .latch_enable_out(sw_054_latch_out),
        .module_data_in  (sw_054_module_data_in),
        .module_data_out (sw_054_module_data_out)
    );

    flygoat_tt02_play_tune flygoat_tt02_play_tune_054 (
        .io_in  (sw_054_module_data_in),
        .io_out (sw_054_module_data_out)
    );

    // [055] https://github.com/mattvenn/clash-silicon-tinytapeout.git
    wire sw_055_clk_out, sw_055_data_out, sw_055_scan_out, sw_055_latch_out;
    wire [7:0] sw_055_module_data_in;
    wire [7:0] sw_055_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_055 (
        .clk_in          (sw_054_clk_out),
        .data_in         (sw_054_data_out),
        .scan_select_in  (sw_054_scan_out),
        .latch_enable_in (sw_054_latch_out),
        .clk_out         (sw_055_clk_out),
        .data_out        (sw_055_data_out),
        .scan_select_out (sw_055_scan_out),
        .latch_enable_out(sw_055_latch_out),
        .module_data_in  (sw_055_module_data_in),
        .module_data_out (sw_055_module_data_out)
    );

    jleightcap_top jleightcap_top_055 (
        .io_in  (sw_055_module_data_in),
        .io_out (sw_055_module_data_out)
    );

    // [056] https://github.com/89Mods/tt2-lcd-namebadge
    wire sw_056_clk_out, sw_056_data_out, sw_056_scan_out, sw_056_latch_out;
    wire [7:0] sw_056_module_data_in;
    wire [7:0] sw_056_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_056 (
        .clk_in          (sw_055_clk_out),
        .data_in         (sw_055_data_out),
        .scan_select_in  (sw_055_scan_out),
        .latch_enable_in (sw_055_latch_out),
        .clk_out         (sw_056_clk_out),
        .data_out        (sw_056_data_out),
        .scan_select_out (sw_056_scan_out),
        .latch_enable_out(sw_056_latch_out),
        .module_data_in  (sw_056_module_data_in),
        .module_data_out (sw_056_module_data_out)
    );

    tt2_tholin_namebadge tt2_tholin_namebadge_056 (
        .io_in  (sw_056_module_data_in),
        .io_out (sw_056_module_data_out)
    );

    // [057] https://github.com/Christina-Cyr/tt02-submission-UART-CC
    wire sw_057_clk_out, sw_057_data_out, sw_057_scan_out, sw_057_latch_out;
    wire [7:0] sw_057_module_data_in;
    wire [7:0] sw_057_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_057 (
        .clk_in          (sw_056_clk_out),
        .data_in         (sw_056_data_out),
        .scan_select_in  (sw_056_scan_out),
        .latch_enable_in (sw_056_latch_out),
        .clk_out         (sw_057_clk_out),
        .data_out        (sw_057_data_out),
        .scan_select_out (sw_057_scan_out),
        .latch_enable_out(sw_057_latch_out),
        .module_data_in  (sw_057_module_data_in),
        .module_data_out (sw_057_module_data_out)
    );

    user_module_347619669052490324 user_module_347619669052490324_057 (
        .io_in  (sw_057_module_data_in),
        .io_out (sw_057_module_data_out)
    );

    // [058] https://github.com/krasin/tt02-verilog-3-bit-8-channel-pwm-driver
    wire sw_058_clk_out, sw_058_data_out, sw_058_scan_out, sw_058_latch_out;
    wire [7:0] sw_058_module_data_in;
    wire [7:0] sw_058_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_058 (
        .clk_in          (sw_057_clk_out),
        .data_in         (sw_057_data_out),
        .scan_select_in  (sw_057_scan_out),
        .latch_enable_in (sw_057_latch_out),
        .clk_out         (sw_058_clk_out),
        .data_out        (sw_058_data_out),
        .scan_select_out (sw_058_scan_out),
        .latch_enable_out(sw_058_latch_out),
        .module_data_in  (sw_058_module_data_in),
        .module_data_out (sw_058_module_data_out)
    );

    krasin_3_bit_8_channel_pwm_driver krasin_3_bit_8_channel_pwm_driver_058 (
        .io_in  (sw_058_module_data_in),
        .io_out (sw_058_module_data_out)
    );

    // [059] https://github.com/nickoe/tinytapeout02-verilog-gds-test
    wire sw_059_clk_out, sw_059_data_out, sw_059_scan_out, sw_059_latch_out;
    wire [7:0] sw_059_module_data_in;
    wire [7:0] sw_059_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_059 (
        .clk_in          (sw_058_clk_out),
        .data_in         (sw_058_data_out),
        .scan_select_in  (sw_058_scan_out),
        .latch_enable_in (sw_058_latch_out),
        .clk_out         (sw_059_clk_out),
        .data_out        (sw_059_data_out),
        .scan_select_out (sw_059_scan_out),
        .latch_enable_out(sw_059_latch_out),
        .module_data_in  (sw_059_module_data_in),
        .module_data_out (sw_059_module_data_out)
    );

    user_module_nickoe user_module_nickoe_059 (
        .io_in  (sw_059_module_data_in),
        .io_out (sw_059_module_data_out)
    );

    // [060] https://github.com/cchan/fp8_mul
    wire sw_060_clk_out, sw_060_data_out, sw_060_scan_out, sw_060_latch_out;
    wire [7:0] sw_060_module_data_in;
    wire [7:0] sw_060_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_060 (
        .clk_in          (sw_059_clk_out),
        .data_in         (sw_059_data_out),
        .scan_select_in  (sw_059_scan_out),
        .latch_enable_in (sw_059_latch_out),
        .clk_out         (sw_060_clk_out),
        .data_out        (sw_060_data_out),
        .scan_select_out (sw_060_scan_out),
        .latch_enable_out(sw_060_latch_out),
        .module_data_in  (sw_060_module_data_in),
        .module_data_out (sw_060_module_data_out)
    );

    cchan_fp8_multiplier cchan_fp8_multiplier_060 (
        .io_in  (sw_060_module_data_in),
        .io_out (sw_060_module_data_out)
    );

    // [061] https://github.com/AvalonSemiconductors/tt2-diceroll
    wire sw_061_clk_out, sw_061_data_out, sw_061_scan_out, sw_061_latch_out;
    wire [7:0] sw_061_module_data_in;
    wire [7:0] sw_061_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_061 (
        .clk_in          (sw_060_clk_out),
        .data_in         (sw_060_data_out),
        .scan_select_in  (sw_060_scan_out),
        .latch_enable_in (sw_060_latch_out),
        .clk_out         (sw_061_clk_out),
        .data_out        (sw_061_data_out),
        .scan_select_out (sw_061_scan_out),
        .latch_enable_out(sw_061_latch_out),
        .module_data_in  (sw_061_module_data_in),
        .module_data_out (sw_061_module_data_out)
    );

    tt2_tholin_diceroll tt2_tholin_diceroll_061 (
        .io_in  (sw_061_module_data_in),
        .io_out (sw_061_module_data_out)
    );

    // [062] https://github.com/NYIT-CNS/cns001-tt02-submission1
    wire sw_062_clk_out, sw_062_data_out, sw_062_scan_out, sw_062_latch_out;
    wire [7:0] sw_062_module_data_in;
    wire [7:0] sw_062_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_062 (
        .clk_in          (sw_061_clk_out),
        .data_in         (sw_061_data_out),
        .scan_select_in  (sw_061_scan_out),
        .latch_enable_in (sw_061_latch_out),
        .clk_out         (sw_062_clk_out),
        .data_out        (sw_062_data_out),
        .scan_select_out (sw_062_scan_out),
        .latch_enable_out(sw_062_latch_out),
        .module_data_in  (sw_062_module_data_in),
        .module_data_out (sw_062_module_data_out)
    );

    user_module_349901899339661908 user_module_349901899339661908_062 (
        .io_in  (sw_062_module_data_in),
        .io_out (sw_062_module_data_out)
    );

    // [063] https://github.com/NYIT-CNS/cns002-tt02-submission2
    wire sw_063_clk_out, sw_063_data_out, sw_063_scan_out, sw_063_latch_out;
    wire [7:0] sw_063_module_data_in;
    wire [7:0] sw_063_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_063 (
        .clk_in          (sw_062_clk_out),
        .data_in         (sw_062_data_out),
        .scan_select_in  (sw_062_scan_out),
        .latch_enable_in (sw_062_latch_out),
        .clk_out         (sw_063_clk_out),
        .data_out        (sw_063_data_out),
        .scan_select_out (sw_063_scan_out),
        .latch_enable_out(sw_063_latch_out),
        .module_data_in  (sw_063_module_data_in),
        .module_data_out (sw_063_module_data_out)
    );

    user_module_349953952950780498 user_module_349953952950780498_063 (
        .io_in  (sw_063_module_data_in),
        .io_out (sw_063_module_data_out)
    );

    // [064] https://github.com/shaos/tt02-submission-shaos
    wire sw_064_clk_out, sw_064_data_out, sw_064_scan_out, sw_064_latch_out;
    wire [7:0] sw_064_module_data_in;
    wire [7:0] sw_064_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_064 (
        .clk_in          (sw_063_clk_out),
        .data_in         (sw_063_data_out),
        .scan_select_in  (sw_063_scan_out),
        .latch_enable_in (sw_063_latch_out),
        .clk_out         (sw_064_clk_out),
        .data_out        (sw_064_data_out),
        .scan_select_out (sw_064_scan_out),
        .latch_enable_out(sw_064_latch_out),
        .module_data_in  (sw_064_module_data_in),
        .module_data_out (sw_064_module_data_out)
    );

    user_module_348540666182107731 user_module_348540666182107731_064 (
        .io_in  (sw_064_module_data_in),
        .io_out (sw_064_module_data_out)
    );

    // [065] https://github.com/toybuilder/tt02-learn-tinytapeout
    wire sw_065_clk_out, sw_065_data_out, sw_065_scan_out, sw_065_latch_out;
    wire [7:0] sw_065_module_data_in;
    wire [7:0] sw_065_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_065 (
        .clk_in          (sw_064_clk_out),
        .data_in         (sw_064_data_out),
        .scan_select_in  (sw_064_scan_out),
        .latch_enable_in (sw_064_latch_out),
        .clk_out         (sw_065_clk_out),
        .data_out        (sw_065_data_out),
        .scan_select_out (sw_065_scan_out),
        .latch_enable_out(sw_065_latch_out),
        .module_data_in  (sw_065_module_data_in),
        .module_data_out (sw_065_module_data_out)
    );

    user_module_341490465660469844 user_module_341490465660469844_065 (
        .io_in  (sw_065_module_data_in),
        .io_out (sw_065_module_data_out)
    );

    // [066] https://github.com/drburke3/tt02-nano-neuron
    wire sw_066_clk_out, sw_066_data_out, sw_066_scan_out, sw_066_latch_out;
    wire [7:0] sw_066_module_data_in;
    wire [7:0] sw_066_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_066 (
        .clk_in          (sw_065_clk_out),
        .data_in         (sw_065_data_out),
        .scan_select_in  (sw_065_scan_out),
        .latch_enable_in (sw_065_latch_out),
        .clk_out         (sw_066_clk_out),
        .data_out        (sw_066_data_out),
        .scan_select_out (sw_066_scan_out),
        .latch_enable_out(sw_066_latch_out),
        .module_data_in  (sw_066_module_data_in),
        .module_data_out (sw_066_module_data_out)
    );

    user_module_349047610915422802 user_module_349047610915422802_066 (
        .io_in  (sw_066_module_data_in),
        .io_out (sw_066_module_data_out)
    );

    // [067] https://github.com/UDXS/sqrt-tt02
    wire sw_067_clk_out, sw_067_data_out, sw_067_scan_out, sw_067_latch_out;
    wire [7:0] sw_067_module_data_in;
    wire [7:0] sw_067_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_067 (
        .clk_in          (sw_066_clk_out),
        .data_in         (sw_066_data_out),
        .scan_select_in  (sw_066_scan_out),
        .latch_enable_in (sw_066_latch_out),
        .clk_out         (sw_067_clk_out),
        .data_out        (sw_067_data_out),
        .scan_select_out (sw_067_scan_out),
        .latch_enable_out(sw_067_latch_out),
        .module_data_in  (sw_067_module_data_in),
        .module_data_out (sw_067_module_data_out)
    );

    udxs_sqrt_top udxs_sqrt_top_067 (
        .io_in  (sw_067_module_data_in),
        .io_out (sw_067_module_data_out)
    );

    // [068] https://github.com/argunda/tt02-breathing-led
    wire sw_068_clk_out, sw_068_data_out, sw_068_scan_out, sw_068_latch_out;
    wire [7:0] sw_068_module_data_in;
    wire [7:0] sw_068_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_068 (
        .clk_in          (sw_067_clk_out),
        .data_in         (sw_067_data_out),
        .scan_select_in  (sw_067_scan_out),
        .latch_enable_in (sw_067_latch_out),
        .clk_out         (sw_068_clk_out),
        .data_out        (sw_068_data_out),
        .scan_select_out (sw_068_scan_out),
        .latch_enable_out(sw_068_latch_out),
        .module_data_in  (sw_068_module_data_in),
        .module_data_out (sw_068_module_data_out)
    );

    pwm_gen pwm_gen_068 (
        .io_in  (sw_068_module_data_in),
        .io_out (sw_068_module_data_out)
    );

    // [069] https://github.com/daniestevez/tt02-gold-fibonacci
    wire sw_069_clk_out, sw_069_data_out, sw_069_scan_out, sw_069_latch_out;
    wire [7:0] sw_069_module_data_in;
    wire [7:0] sw_069_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_069 (
        .clk_in          (sw_068_clk_out),
        .data_in         (sw_068_data_out),
        .scan_select_in  (sw_068_scan_out),
        .latch_enable_in (sw_068_latch_out),
        .clk_out         (sw_069_clk_out),
        .data_out        (sw_069_data_out),
        .scan_select_out (sw_069_scan_out),
        .latch_enable_out(sw_069_latch_out),
        .module_data_in  (sw_069_module_data_in),
        .module_data_out (sw_069_module_data_out)
    );

    user_module_341164910646919762 user_module_341164910646919762_069 (
        .io_in  (sw_069_module_data_in),
        .io_out (sw_069_module_data_out)
    );

    // [070] https://github.com/r4d10n/tt02-HELLo-3orLd-7seg
    wire sw_070_clk_out, sw_070_data_out, sw_070_scan_out, sw_070_latch_out;
    wire [7:0] sw_070_module_data_in;
    wire [7:0] sw_070_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_070 (
        .clk_in          (sw_069_clk_out),
        .data_in         (sw_069_data_out),
        .scan_select_in  (sw_069_scan_out),
        .latch_enable_in (sw_069_latch_out),
        .clk_out         (sw_070_clk_out),
        .data_out        (sw_070_data_out),
        .scan_select_out (sw_070_scan_out),
        .latch_enable_out(sw_070_latch_out),
        .module_data_in  (sw_070_module_data_in),
        .module_data_out (sw_070_module_data_out)
    );

    user_module_341609034095264340 user_module_341609034095264340_070 (
        .io_in  (sw_070_module_data_in),
        .io_out (sw_070_module_data_out)
    );

    // [071] https://github.com/navray/tt02-square-root
    wire sw_071_clk_out, sw_071_data_out, sw_071_scan_out, sw_071_latch_out;
    wire [7:0] sw_071_module_data_in;
    wire [7:0] sw_071_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_071 (
        .clk_in          (sw_070_clk_out),
        .data_in         (sw_070_data_out),
        .scan_select_in  (sw_070_scan_out),
        .latch_enable_in (sw_070_latch_out),
        .clk_out         (sw_071_clk_out),
        .data_out        (sw_071_data_out),
        .scan_select_out (sw_071_scan_out),
        .latch_enable_out(sw_071_latch_out),
        .module_data_in  (sw_071_module_data_in),
        .module_data_out (sw_071_module_data_out)
    );

    navray_top navray_top_071 (
        .io_in  (sw_071_module_data_in),
        .io_out (sw_071_module_data_out)
    );

    // [072] https://github.com/shaos-net/tt02-submission-shaos2
    wire sw_072_clk_out, sw_072_data_out, sw_072_scan_out, sw_072_latch_out;
    wire [7:0] sw_072_module_data_in;
    wire [7:0] sw_072_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_072 (
        .clk_in          (sw_071_clk_out),
        .data_in         (sw_071_data_out),
        .scan_select_in  (sw_071_scan_out),
        .latch_enable_in (sw_071_latch_out),
        .clk_out         (sw_072_clk_out),
        .data_out        (sw_072_data_out),
        .scan_select_out (sw_072_scan_out),
        .latch_enable_out(sw_072_latch_out),
        .module_data_in  (sw_072_module_data_in),
        .module_data_out (sw_072_module_data_out)
    );

    user_module_349011320806310484 user_module_349011320806310484_072 (
        .io_in  (sw_072_module_data_in),
        .io_out (sw_072_module_data_out)
    );

    // [073] https://github.com/krasin/tt02-verilog-spi-7-channel-pwm-driver
    wire sw_073_clk_out, sw_073_data_out, sw_073_scan_out, sw_073_latch_out;
    wire [7:0] sw_073_module_data_in;
    wire [7:0] sw_073_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_073 (
        .clk_in          (sw_072_clk_out),
        .data_in         (sw_072_data_out),
        .scan_select_in  (sw_072_scan_out),
        .latch_enable_in (sw_072_latch_out),
        .clk_out         (sw_073_clk_out),
        .data_out        (sw_073_data_out),
        .scan_select_out (sw_073_scan_out),
        .latch_enable_out(sw_073_latch_out),
        .module_data_in  (sw_073_module_data_in),
        .module_data_out (sw_073_module_data_out)
    );

    krasin_tt02_verilog_spi_7_channel_pwm_driver krasin_tt02_verilog_spi_7_channel_pwm_driver_073 (
        .io_in  (sw_073_module_data_in),
        .io_out (sw_073_module_data_out)
    );

    // [074] https://github.com/brouhaha/tt02-hex-sr
    wire sw_074_clk_out, sw_074_data_out, sw_074_scan_out, sw_074_latch_out;
    wire [7:0] sw_074_module_data_in;
    wire [7:0] sw_074_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_074 (
        .clk_in          (sw_073_clk_out),
        .data_in         (sw_073_data_out),
        .scan_select_in  (sw_073_scan_out),
        .latch_enable_in (sw_073_latch_out),
        .clk_out         (sw_074_clk_out),
        .data_out        (sw_074_data_out),
        .scan_select_out (sw_074_scan_out),
        .latch_enable_out(sw_074_latch_out),
        .module_data_in  (sw_074_module_data_in),
        .module_data_out (sw_074_module_data_out)
    );

    hex_sr hex_sr_074 (
        .io_in  (sw_074_module_data_in),
        .io_out (sw_074_module_data_out)
    );

    // [075] https://github.com/ericsmi/tt02-verilog-ring-osc-demo
    wire sw_075_clk_out, sw_075_data_out, sw_075_scan_out, sw_075_latch_out;
    wire [7:0] sw_075_module_data_in;
    wire [7:0] sw_075_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_075 (
        .clk_in          (sw_074_clk_out),
        .data_in         (sw_074_data_out),
        .scan_select_in  (sw_074_scan_out),
        .latch_enable_in (sw_074_latch_out),
        .clk_out         (sw_075_clk_out),
        .data_out        (sw_075_data_out),
        .scan_select_out (sw_075_scan_out),
        .latch_enable_out(sw_075_latch_out),
        .module_data_in  (sw_075_module_data_in),
        .module_data_out (sw_075_module_data_out)
    );

    ericsmi_speed_test ericsmi_speed_test_075 (
        .io_in  (sw_075_module_data_in),
        .io_out (sw_075_module_data_out)
    );

    // [076] https://github.com/AidanMedcalf/tt02-pid
    wire sw_076_clk_out, sw_076_data_out, sw_076_scan_out, sw_076_latch_out;
    wire [7:0] sw_076_module_data_in;
    wire [7:0] sw_076_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_076 (
        .clk_in          (sw_075_clk_out),
        .data_in         (sw_075_data_out),
        .scan_select_in  (sw_075_scan_out),
        .latch_enable_in (sw_075_latch_out),
        .clk_out         (sw_076_clk_out),
        .data_out        (sw_076_data_out),
        .scan_select_out (sw_076_scan_out),
        .latch_enable_out(sw_076_latch_out),
        .module_data_in  (sw_076_module_data_in),
        .module_data_out (sw_076_module_data_out)
    );

    AidanMedcalf_pid_controller AidanMedcalf_pid_controller_076 (
        .io_in  (sw_076_module_data_in),
        .io_out (sw_076_module_data_out)
    );

    // [077] https://github.com/cpldcpu/tt02-TrainLED
    wire sw_077_clk_out, sw_077_data_out, sw_077_scan_out, sw_077_latch_out;
    wire [7:0] sw_077_module_data_in;
    wire [7:0] sw_077_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_077 (
        .clk_in          (sw_076_clk_out),
        .data_in         (sw_076_data_out),
        .scan_select_in  (sw_076_scan_out),
        .latch_enable_in (sw_076_latch_out),
        .clk_out         (sw_077_clk_out),
        .data_out        (sw_077_data_out),
        .scan_select_out (sw_077_scan_out),
        .latch_enable_out(sw_077_latch_out),
        .module_data_in  (sw_077_module_data_in),
        .module_data_out (sw_077_module_data_out)
    );

    cpldcpu_TrainLED2top cpldcpu_TrainLED2top_077 (
        .io_in  (sw_077_module_data_in),
        .io_out (sw_077_module_data_out)
    );

    // [078] https://github.com/cpldcpu/tt02-mcpu5plus
    wire sw_078_clk_out, sw_078_data_out, sw_078_scan_out, sw_078_latch_out;
    wire [7:0] sw_078_module_data_in;
    wire [7:0] sw_078_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_078 (
        .clk_in          (sw_077_clk_out),
        .data_in         (sw_077_data_out),
        .scan_select_in  (sw_077_scan_out),
        .latch_enable_in (sw_077_latch_out),
        .clk_out         (sw_078_clk_out),
        .data_out        (sw_078_data_out),
        .scan_select_out (sw_078_scan_out),
        .latch_enable_out(sw_078_latch_out),
        .module_data_in  (sw_078_module_data_in),
        .module_data_out (sw_078_module_data_out)
    );

    cpldcpu_MCPU5plus cpldcpu_MCPU5plus_078 (
        .io_in  (sw_078_module_data_in),
        .io_out (sw_078_module_data_out)
    );

    // [079] https://github.com/MoonbaseOtago/tt-cpu
    wire sw_079_clk_out, sw_079_data_out, sw_079_scan_out, sw_079_latch_out;
    wire [7:0] sw_079_module_data_in;
    wire [7:0] sw_079_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_079 (
        .clk_in          (sw_078_clk_out),
        .data_in         (sw_078_data_out),
        .scan_select_in  (sw_078_scan_out),
        .latch_enable_in (sw_078_latch_out),
        .clk_out         (sw_079_clk_out),
        .data_out        (sw_079_data_out),
        .scan_select_out (sw_079_scan_out),
        .latch_enable_out(sw_079_latch_out),
        .module_data_in  (sw_079_module_data_in),
        .module_data_out (sw_079_module_data_out)
    );

    moonbase_cpu_4bit moonbase_cpu_4bit_079 (
        .io_in  (sw_079_module_data_in),
        .io_out (sw_079_module_data_out)
    );

    // [080] https://github.com/davidsiaw/tt02-davidsiaw-stackcalc
    wire sw_080_clk_out, sw_080_data_out, sw_080_scan_out, sw_080_latch_out;
    wire [7:0] sw_080_module_data_in;
    wire [7:0] sw_080_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_080 (
        .clk_in          (sw_079_clk_out),
        .data_in         (sw_079_data_out),
        .scan_select_in  (sw_079_scan_out),
        .latch_enable_in (sw_079_latch_out),
        .clk_out         (sw_080_clk_out),
        .data_out        (sw_080_data_out),
        .scan_select_out (sw_080_scan_out),
        .latch_enable_out(sw_080_latch_out),
        .module_data_in  (sw_080_module_data_in),
        .module_data_out (sw_080_module_data_out)
    );

    davidsiaw_stackcalc davidsiaw_stackcalc_080 (
        .io_in  (sw_080_module_data_in),
        .io_out (sw_080_module_data_out)
    );

    // [081] https://github.com/mole99/tt02-1bit-alu
    wire sw_081_clk_out, sw_081_data_out, sw_081_scan_out, sw_081_latch_out;
    wire [7:0] sw_081_module_data_in;
    wire [7:0] sw_081_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_081 (
        .clk_in          (sw_080_clk_out),
        .data_in         (sw_080_data_out),
        .scan_select_in  (sw_080_scan_out),
        .latch_enable_in (sw_080_latch_out),
        .clk_out         (sw_081_clk_out),
        .data_out        (sw_081_data_out),
        .scan_select_out (sw_081_scan_out),
        .latch_enable_out(sw_081_latch_out),
        .module_data_in  (sw_081_module_data_in),
        .module_data_out (sw_081_module_data_out)
    );

    user_module_340318610245288530 user_module_340318610245288530_081 (
        .io_in  (sw_081_module_data_in),
        .io_out (sw_081_module_data_out)
    );

    // [082] https://github.com/steieio/tt02-sfsm-wokwi
    wire sw_082_clk_out, sw_082_data_out, sw_082_scan_out, sw_082_latch_out;
    wire [7:0] sw_082_module_data_in;
    wire [7:0] sw_082_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_082 (
        .clk_in          (sw_081_clk_out),
        .data_in         (sw_081_data_out),
        .scan_select_in  (sw_081_scan_out),
        .latch_enable_in (sw_081_latch_out),
        .clk_out         (sw_082_clk_out),
        .data_out        (sw_082_data_out),
        .scan_select_out (sw_082_scan_out),
        .latch_enable_out(sw_082_latch_out),
        .module_data_in  (sw_082_module_data_in),
        .module_data_out (sw_082_module_data_out)
    );

    user_module_349228308755382868 user_module_349228308755382868_082 (
        .io_in  (sw_082_module_data_in),
        .io_out (sw_082_module_data_out)
    );

    // [083] https://github.com/youngpines/tt02-youngpines-submission
    wire sw_083_clk_out, sw_083_data_out, sw_083_scan_out, sw_083_latch_out;
    wire [7:0] sw_083_module_data_in;
    wire [7:0] sw_083_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_083 (
        .clk_in          (sw_082_clk_out),
        .data_in         (sw_082_data_out),
        .scan_select_in  (sw_082_scan_out),
        .latch_enable_in (sw_082_latch_out),
        .clk_out         (sw_083_clk_out),
        .data_out        (sw_083_data_out),
        .scan_select_out (sw_083_scan_out),
        .latch_enable_out(sw_083_latch_out),
        .module_data_in  (sw_083_module_data_in),
        .module_data_out (sw_083_module_data_out)
    );

    user_module_341571228858843732 user_module_341571228858843732_083 (
        .io_in  (sw_083_module_data_in),
        .io_out (sw_083_module_data_out)
    );

    // [084] https://github.com/timvgso/tinatapeworm
    wire sw_084_clk_out, sw_084_data_out, sw_084_scan_out, sw_084_latch_out;
    wire [7:0] sw_084_module_data_in;
    wire [7:0] sw_084_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_084 (
        .clk_in          (sw_083_clk_out),
        .data_in         (sw_083_data_out),
        .scan_select_in  (sw_083_scan_out),
        .latch_enable_in (sw_083_latch_out),
        .clk_out         (sw_084_clk_out),
        .data_out        (sw_084_data_out),
        .scan_select_out (sw_084_scan_out),
        .latch_enable_out(sw_084_latch_out),
        .module_data_in  (sw_084_module_data_in),
        .module_data_out (sw_084_module_data_out)
    );

    user_module_348381622440034899 user_module_348381622440034899_084 (
        .io_in  (sw_084_module_data_in),
        .io_out (sw_084_module_data_out)
    );

    // [085] https://github.com/OneRNG/tt-cpu8
    wire sw_085_clk_out, sw_085_data_out, sw_085_scan_out, sw_085_latch_out;
    wire [7:0] sw_085_module_data_in;
    wire [7:0] sw_085_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_085 (
        .clk_in          (sw_084_clk_out),
        .data_in         (sw_084_data_out),
        .scan_select_in  (sw_084_scan_out),
        .latch_enable_in (sw_084_latch_out),
        .clk_out         (sw_085_clk_out),
        .data_out        (sw_085_data_out),
        .scan_select_out (sw_085_scan_out),
        .latch_enable_out(sw_085_latch_out),
        .module_data_in  (sw_085_module_data_in),
        .module_data_out (sw_085_module_data_out)
    );

    moonbase_cpu_8bit moonbase_cpu_8bit_085 (
        .io_in  (sw_085_module_data_in),
        .io_out (sw_085_module_data_out)
    );

    // [086] https://github.com/tcptomato/tt02-submission-template
    wire sw_086_clk_out, sw_086_data_out, sw_086_scan_out, sw_086_latch_out;
    wire [7:0] sw_086_module_data_in;
    wire [7:0] sw_086_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_086 (
        .clk_in          (sw_085_clk_out),
        .data_in         (sw_085_data_out),
        .scan_select_in  (sw_085_scan_out),
        .latch_enable_in (sw_085_latch_out),
        .clk_out         (sw_086_clk_out),
        .data_out        (sw_086_data_out),
        .scan_select_out (sw_086_scan_out),
        .latch_enable_out(sw_086_latch_out),
        .module_data_in  (sw_086_module_data_in),
        .module_data_out (sw_086_module_data_out)
    );

    user_module_341178154799333971 user_module_341178154799333971_086 (
        .io_in  (sw_086_module_data_in),
        .io_out (sw_086_module_data_out)
    );

    // [087] https://github.com/jglim/tt02-bcd-7seg
    wire sw_087_clk_out, sw_087_data_out, sw_087_scan_out, sw_087_latch_out;
    wire [7:0] sw_087_module_data_in;
    wire [7:0] sw_087_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_087 (
        .clk_in          (sw_086_clk_out),
        .data_in         (sw_086_data_out),
        .scan_select_in  (sw_086_scan_out),
        .latch_enable_in (sw_086_latch_out),
        .clk_out         (sw_087_clk_out),
        .data_out        (sw_087_data_out),
        .scan_select_out (sw_087_scan_out),
        .latch_enable_out(sw_087_latch_out),
        .module_data_in  (sw_087_module_data_in),
        .module_data_out (sw_087_module_data_out)
    );

    user_module_349546262775726676 user_module_349546262775726676_087 (
        .io_in  (sw_087_module_data_in),
        .io_out (sw_087_module_data_out)
    );

    // [088] https://github.com/ARamsey118/tiny_tapeout_freq_counter
    wire sw_088_clk_out, sw_088_data_out, sw_088_scan_out, sw_088_latch_out;
    wire [7:0] sw_088_module_data_in;
    wire [7:0] sw_088_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_088 (
        .clk_in          (sw_087_clk_out),
        .data_in         (sw_087_data_out),
        .scan_select_in  (sw_087_scan_out),
        .latch_enable_in (sw_087_latch_out),
        .clk_out         (sw_088_clk_out),
        .data_out        (sw_088_data_out),
        .scan_select_out (sw_088_scan_out),
        .latch_enable_out(sw_088_latch_out),
        .module_data_in  (sw_088_module_data_in),
        .module_data_out (sw_088_module_data_out)
    );

    aramsey118_freq_counter aramsey118_freq_counter_088 (
        .io_in  (sw_088_module_data_in),
        .io_out (sw_088_module_data_out)
    );

    // [089] https://github.com/splinedrive/thunderbird_taillight_1965
    wire sw_089_clk_out, sw_089_data_out, sw_089_scan_out, sw_089_latch_out;
    wire [7:0] sw_089_module_data_in;
    wire [7:0] sw_089_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_089 (
        .clk_in          (sw_088_clk_out),
        .data_in         (sw_088_data_out),
        .scan_select_in  (sw_088_scan_out),
        .latch_enable_in (sw_088_latch_out),
        .clk_out         (sw_089_clk_out),
        .data_out        (sw_089_data_out),
        .scan_select_out (sw_089_scan_out),
        .latch_enable_out(sw_089_latch_out),
        .module_data_in  (sw_089_module_data_in),
        .module_data_out (sw_089_module_data_out)
    );

    thunderbird_taillight_ctrl thunderbird_taillight_ctrl_089 (
        .io_in  (sw_089_module_data_in),
        .io_out (sw_089_module_data_out)
    );

    // [090] https://github.com/gatecat/tt02-fpga-respin
    wire sw_090_clk_out, sw_090_data_out, sw_090_scan_out, sw_090_latch_out;
    wire [7:0] sw_090_module_data_in;
    wire [7:0] sw_090_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_090 (
        .clk_in          (sw_089_clk_out),
        .data_in         (sw_089_data_out),
        .scan_select_in  (sw_089_scan_out),
        .latch_enable_in (sw_089_latch_out),
        .clk_out         (sw_090_clk_out),
        .data_out        (sw_090_data_out),
        .scan_select_out (sw_090_scan_out),
        .latch_enable_out(sw_090_latch_out),
        .module_data_in  (sw_090_module_data_in),
        .module_data_out (sw_090_module_data_out)
    );

    gatecat_fpga_top gatecat_fpga_top_090 (
        .io_in  (sw_090_module_data_in),
        .io_out (sw_090_module_data_out)
    );

    // [091] https://github.com/mmolteni-secpat/tinytapeout02_chi2shares
    wire sw_091_clk_out, sw_091_data_out, sw_091_scan_out, sw_091_latch_out;
    wire [7:0] sw_091_module_data_in;
    wire [7:0] sw_091_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_091 (
        .clk_in          (sw_090_clk_out),
        .data_in         (sw_090_data_out),
        .scan_select_in  (sw_090_scan_out),
        .latch_enable_in (sw_090_latch_out),
        .clk_out         (sw_091_clk_out),
        .data_out        (sw_091_data_out),
        .scan_select_out (sw_091_scan_out),
        .latch_enable_out(sw_091_latch_out),
        .module_data_in  (sw_091_module_data_in),
        .module_data_out (sw_091_module_data_out)
    );

    user_module_341589685194195540 user_module_341589685194195540_091 (
        .io_in  (sw_091_module_data_in),
        .io_out (sw_091_module_data_out)
    );

    // [092] https://github.com/mmolteni-secpat/tinytapeout02_chi3shares
    wire sw_092_clk_out, sw_092_data_out, sw_092_scan_out, sw_092_latch_out;
    wire [7:0] sw_092_module_data_in;
    wire [7:0] sw_092_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_092 (
        .clk_in          (sw_091_clk_out),
        .data_in         (sw_091_data_out),
        .scan_select_in  (sw_091_scan_out),
        .latch_enable_in (sw_091_latch_out),
        .clk_out         (sw_092_clk_out),
        .data_out        (sw_092_data_out),
        .scan_select_out (sw_092_scan_out),
        .latch_enable_out(sw_092_latch_out),
        .module_data_in  (sw_092_module_data_in),
        .module_data_out (sw_092_module_data_out)
    );

    user_module_341608574336631379 user_module_341608574336631379_092 (
        .io_in  (sw_092_module_data_in),
        .io_out (sw_092_module_data_out)
    );

    // [093] https://github.com/Wren6991/tt02-whisk-serial-processor
    wire sw_093_clk_out, sw_093_data_out, sw_093_scan_out, sw_093_latch_out;
    wire [7:0] sw_093_module_data_in;
    wire [7:0] sw_093_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_093 (
        .clk_in          (sw_092_clk_out),
        .data_in         (sw_092_data_out),
        .scan_select_in  (sw_092_scan_out),
        .latch_enable_in (sw_092_latch_out),
        .clk_out         (sw_093_clk_out),
        .data_out        (sw_093_data_out),
        .scan_select_out (sw_093_scan_out),
        .latch_enable_out(sw_093_latch_out),
        .module_data_in  (sw_093_module_data_in),
        .module_data_out (sw_093_module_data_out)
    );

    wren6991_whisk_tt2_io_wrapper wren6991_whisk_tt2_io_wrapper_093 (
        .io_in  (sw_093_module_data_in),
        .io_out (sw_093_module_data_out)
    );

    // [094] https://github.com/aiunderstand/tt02-4bit-tristate-loadable-counter
    wire sw_094_clk_out, sw_094_data_out, sw_094_scan_out, sw_094_latch_out;
    wire [7:0] sw_094_module_data_in;
    wire [7:0] sw_094_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_094 (
        .clk_in          (sw_093_clk_out),
        .data_in         (sw_093_data_out),
        .scan_select_in  (sw_093_scan_out),
        .latch_enable_in (sw_093_latch_out),
        .clk_out         (sw_094_clk_out),
        .data_out        (sw_094_data_out),
        .scan_select_out (sw_094_scan_out),
        .latch_enable_out(sw_094_latch_out),
        .module_data_in  (sw_094_module_data_in),
        .module_data_out (sw_094_module_data_out)
    );

    user_module_341423712597181012 user_module_341423712597181012_094 (
        .io_in  (sw_094_module_data_in),
        .io_out (sw_094_module_data_out)
    );

    // [095] https://github.com/aiunderstand/tt02-async-binary-ternary-convert-compare
    wire sw_095_clk_out, sw_095_data_out, sw_095_scan_out, sw_095_latch_out;
    wire [7:0] sw_095_module_data_in;
    wire [7:0] sw_095_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_095 (
        .clk_in          (sw_094_clk_out),
        .data_in         (sw_094_data_out),
        .scan_select_in  (sw_094_scan_out),
        .latch_enable_in (sw_094_latch_out),
        .clk_out         (sw_095_clk_out),
        .data_out        (sw_095_data_out),
        .scan_select_out (sw_095_scan_out),
        .latch_enable_out(sw_095_latch_out),
        .module_data_in  (sw_095_module_data_in),
        .module_data_out (sw_095_module_data_out)
    );

    user_module_341277789473735250 user_module_341277789473735250_095 (
        .io_in  (sw_095_module_data_in),
        .io_out (sw_095_module_data_out)
    );

    // [096] https://github.com/RobertRiachi/tt02-dot-product
    wire sw_096_clk_out, sw_096_data_out, sw_096_scan_out, sw_096_latch_out;
    wire [7:0] sw_096_module_data_in;
    wire [7:0] sw_096_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_096 (
        .clk_in          (sw_095_clk_out),
        .data_in         (sw_095_data_out),
        .scan_select_in  (sw_095_scan_out),
        .latch_enable_in (sw_095_latch_out),
        .clk_out         (sw_096_clk_out),
        .data_out        (sw_096_data_out),
        .scan_select_out (sw_096_scan_out),
        .latch_enable_out(sw_096_latch_out),
        .module_data_in  (sw_096_module_data_in),
        .module_data_out (sw_096_module_data_out)
    );

    user_module_348787952842703444 user_module_348787952842703444_096 (
        .io_in  (sw_096_module_data_in),
        .io_out (sw_096_module_data_out)
    );

    // [097] https://github.com/regymm/tt02-verilog-mcpi
    wire sw_097_clk_out, sw_097_data_out, sw_097_scan_out, sw_097_latch_out;
    wire [7:0] sw_097_module_data_in;
    wire [7:0] sw_097_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_097 (
        .clk_in          (sw_096_clk_out),
        .data_in         (sw_096_data_out),
        .scan_select_in  (sw_096_scan_out),
        .latch_enable_in (sw_096_latch_out),
        .clk_out         (sw_097_clk_out),
        .data_out        (sw_097_data_out),
        .scan_select_out (sw_097_scan_out),
        .latch_enable_out(sw_097_latch_out),
        .module_data_in  (sw_097_module_data_in),
        .module_data_out (sw_097_module_data_out)
    );

    regymm_mcpi regymm_mcpi_097 (
        .io_in  (sw_097_module_data_in),
        .io_out (sw_097_module_data_out)
    );

    // [098] https://github.com/regymm/tt02-verilog-funnyblinky
    wire sw_098_clk_out, sw_098_data_out, sw_098_scan_out, sw_098_latch_out;
    wire [7:0] sw_098_module_data_in;
    wire [7:0] sw_098_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_098 (
        .clk_in          (sw_097_clk_out),
        .data_in         (sw_097_data_out),
        .scan_select_in  (sw_097_scan_out),
        .latch_enable_in (sw_097_latch_out),
        .clk_out         (sw_098_clk_out),
        .data_out        (sw_098_data_out),
        .scan_select_out (sw_098_scan_out),
        .latch_enable_out(sw_098_latch_out),
        .module_data_in  (sw_098_module_data_in),
        .module_data_out (sw_098_module_data_out)
    );

    regymm_funnyblinky regymm_funnyblinky_098 (
        .io_in  (sw_098_module_data_in),
        .io_out (sw_098_module_data_out)
    );

    // [099] https://github.com/adamgreig/tt02-gpa-ca-prn
    wire sw_099_clk_out, sw_099_data_out, sw_099_scan_out, sw_099_latch_out;
    wire [7:0] sw_099_module_data_in;
    wire [7:0] sw_099_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_099 (
        .clk_in          (sw_098_clk_out),
        .data_in         (sw_098_data_out),
        .scan_select_in  (sw_098_scan_out),
        .latch_enable_in (sw_098_latch_out),
        .clk_out         (sw_099_clk_out),
        .data_out        (sw_099_data_out),
        .scan_select_out (sw_099_scan_out),
        .latch_enable_out(sw_099_latch_out),
        .module_data_in  (sw_099_module_data_in),
        .module_data_out (sw_099_module_data_out)
    );

    adamgreig_tt02_gps_ca_prn adamgreig_tt02_gps_ca_prn_099 (
        .io_in  (sw_099_module_data_in),
        .io_out (sw_099_module_data_out)
    );

    // [100] https://github.com/adamgreig/tt02-adc-dac
    wire sw_100_clk_out, sw_100_data_out, sw_100_scan_out, sw_100_latch_out;
    wire [7:0] sw_100_module_data_in;
    wire [7:0] sw_100_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_100 (
        .clk_in          (sw_099_clk_out),
        .data_in         (sw_099_data_out),
        .scan_select_in  (sw_099_scan_out),
        .latch_enable_in (sw_099_latch_out),
        .clk_out         (sw_100_clk_out),
        .data_out        (sw_100_data_out),
        .scan_select_out (sw_100_scan_out),
        .latch_enable_out(sw_100_latch_out),
        .module_data_in  (sw_100_module_data_in),
        .module_data_out (sw_100_module_data_out)
    );

    adamgreig_tt02_adc_dac adamgreig_tt02_adc_dac_100 (
        .io_in  (sw_100_module_data_in),
        .io_out (sw_100_module_data_out)
    );

    // [101] https://github.com/jglim/tt02-bcd-hex7seg-hdl
    wire sw_101_clk_out, sw_101_data_out, sw_101_scan_out, sw_101_latch_out;
    wire [7:0] sw_101_module_data_in;
    wire [7:0] sw_101_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_101 (
        .clk_in          (sw_100_clk_out),
        .data_in         (sw_100_data_out),
        .scan_select_in  (sw_100_scan_out),
        .latch_enable_in (sw_100_latch_out),
        .clk_out         (sw_101_clk_out),
        .data_out        (sw_101_data_out),
        .scan_select_out (sw_101_scan_out),
        .latch_enable_out(sw_101_latch_out),
        .module_data_in  (sw_101_module_data_in),
        .module_data_out (sw_101_module_data_out)
    );

    jglim_7seg jglim_7seg_101 (
        .io_in  (sw_101_module_data_in),
        .io_out (sw_101_module_data_out)
    );

    // [102] https://github.com/burtyb/tt02-srld
    wire sw_102_clk_out, sw_102_data_out, sw_102_scan_out, sw_102_latch_out;
    wire [7:0] sw_102_module_data_in;
    wire [7:0] sw_102_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_102 (
        .clk_in          (sw_101_clk_out),
        .data_in         (sw_101_data_out),
        .scan_select_in  (sw_101_scan_out),
        .latch_enable_in (sw_101_latch_out),
        .clk_out         (sw_102_clk_out),
        .data_out        (sw_102_data_out),
        .scan_select_out (sw_102_scan_out),
        .latch_enable_out(sw_102_latch_out),
        .module_data_in  (sw_102_module_data_in),
        .module_data_out (sw_102_module_data_out)
    );

    user_module_349790606404354643 user_module_349790606404354643_102 (
        .io_in  (sw_102_module_data_in),
        .io_out (sw_102_module_data_out)
    );

    // [103] https://github.com/azzeloof/tt02-counter
    wire sw_103_clk_out, sw_103_data_out, sw_103_scan_out, sw_103_latch_out;
    wire [7:0] sw_103_module_data_in;
    wire [7:0] sw_103_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_103 (
        .clk_in          (sw_102_clk_out),
        .data_in         (sw_102_data_out),
        .scan_select_in  (sw_102_scan_out),
        .latch_enable_in (sw_102_latch_out),
        .clk_out         (sw_103_clk_out),
        .data_out        (sw_103_data_out),
        .scan_select_out (sw_103_scan_out),
        .latch_enable_out(sw_103_latch_out),
        .module_data_in  (sw_103_module_data_in),
        .module_data_out (sw_103_module_data_out)
    );

    user_module_341279123277087315 user_module_341279123277087315_103 (
        .io_in  (sw_103_module_data_in),
        .io_out (sw_103_module_data_out)
    );

    // [104] https://github.com/shan1293/tt02-2bitCPU
    wire sw_104_clk_out, sw_104_data_out, sw_104_scan_out, sw_104_latch_out;
    wire [7:0] sw_104_module_data_in;
    wire [7:0] sw_104_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_104 (
        .clk_in          (sw_103_clk_out),
        .data_in         (sw_103_data_out),
        .scan_select_in  (sw_103_scan_out),
        .latch_enable_in (sw_103_latch_out),
        .clk_out         (sw_104_clk_out),
        .data_out        (sw_104_data_out),
        .scan_select_out (sw_104_scan_out),
        .latch_enable_out(sw_104_latch_out),
        .module_data_in  (sw_104_module_data_in),
        .module_data_out (sw_104_module_data_out)
    );

    shan1293_2bitalu shan1293_2bitalu_104 (
        .io_in  (sw_104_module_data_in),
        .io_out (sw_104_module_data_out)
    );

    // [105] https://github.com/Josvth/tt02-convolutional-encoder
    wire sw_105_clk_out, sw_105_data_out, sw_105_scan_out, sw_105_latch_out;
    wire [7:0] sw_105_module_data_in;
    wire [7:0] sw_105_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_105 (
        .clk_in          (sw_104_clk_out),
        .data_in         (sw_104_data_out),
        .scan_select_in  (sw_104_scan_out),
        .latch_enable_in (sw_104_latch_out),
        .clk_out         (sw_105_clk_out),
        .data_out        (sw_105_data_out),
        .scan_select_out (sw_105_scan_out),
        .latch_enable_out(sw_105_latch_out),
        .module_data_in  (sw_105_module_data_in),
        .module_data_out (sw_105_module_data_out)
    );

    user_module_349729432862196307 user_module_349729432862196307_105 (
        .io_in  (sw_105_module_data_in),
        .io_out (sw_105_module_data_out)
    );

    // [106] https://github.com/gatecat/tt02-pic
    wire sw_106_clk_out, sw_106_data_out, sw_106_scan_out, sw_106_latch_out;
    wire [7:0] sw_106_module_data_in;
    wire [7:0] sw_106_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_106 (
        .clk_in          (sw_105_clk_out),
        .data_in         (sw_105_data_out),
        .scan_select_in  (sw_105_scan_out),
        .latch_enable_in (sw_105_latch_out),
        .clk_out         (sw_106_clk_out),
        .data_out        (sw_106_data_out),
        .scan_select_out (sw_106_scan_out),
        .latch_enable_out(sw_106_latch_out),
        .module_data_in  (sw_106_module_data_in),
        .module_data_out (sw_106_module_data_out)
    );

    tiny_kinda_pic tiny_kinda_pic_106 (
        .io_in  (sw_106_module_data_in),
        .io_out (sw_106_module_data_out)
    );

    // [107] https://github.com/browndeer/rv8u
    wire sw_107_clk_out, sw_107_data_out, sw_107_scan_out, sw_107_latch_out;
    wire [7:0] sw_107_module_data_in;
    wire [7:0] sw_107_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_107 (
        .clk_in          (sw_106_clk_out),
        .data_in         (sw_106_data_out),
        .scan_select_in  (sw_106_scan_out),
        .latch_enable_in (sw_106_latch_out),
        .clk_out         (sw_107_clk_out),
        .data_out        (sw_107_data_out),
        .scan_select_out (sw_107_scan_out),
        .latch_enable_out(sw_107_latch_out),
        .module_data_in  (sw_107_module_data_in),
        .module_data_out (sw_107_module_data_out)
    );

    browndeer_rv8u browndeer_rv8u_107 (
        .io_in  (sw_107_module_data_in),
        .io_out (sw_107_module_data_out)
    );

    // [108] https://github.com/Sirawit7205/tt02-2G97-2G98
    wire sw_108_clk_out, sw_108_data_out, sw_108_scan_out, sw_108_latch_out;
    wire [7:0] sw_108_module_data_in;
    wire [7:0] sw_108_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_108 (
        .clk_in          (sw_107_clk_out),
        .data_in         (sw_107_data_out),
        .scan_select_in  (sw_107_scan_out),
        .latch_enable_in (sw_107_latch_out),
        .clk_out         (sw_108_clk_out),
        .data_out        (sw_108_data_out),
        .scan_select_out (sw_108_scan_out),
        .latch_enable_out(sw_108_latch_out),
        .module_data_in  (sw_108_module_data_in),
        .module_data_out (sw_108_module_data_out)
    );

    user_module_341432030163108435 user_module_341432030163108435_108 (
        .io_in  (sw_108_module_data_in),
        .io_out (sw_108_module_data_out)
    );

    // [109] https://github.com/gatecat/tt02-melody-gen
    wire sw_109_clk_out, sw_109_data_out, sw_109_scan_out, sw_109_latch_out;
    wire [7:0] sw_109_module_data_in;
    wire [7:0] sw_109_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_109 (
        .clk_in          (sw_108_clk_out),
        .data_in         (sw_108_data_out),
        .scan_select_in  (sw_108_scan_out),
        .latch_enable_in (sw_108_latch_out),
        .clk_out         (sw_109_clk_out),
        .data_out        (sw_109_data_out),
        .scan_select_out (sw_109_scan_out),
        .latch_enable_out(sw_109_latch_out),
        .module_data_in  (sw_109_module_data_in),
        .module_data_out (sw_109_module_data_out)
    );

    prog_melody_gen prog_melody_gen_109 (
        .io_in  (sw_109_module_data_in),
        .io_out (sw_109_module_data_out)
    );

    // [110] https://github.com/vaishnavachath/tt02-submission-rotary-encoder-counter
    wire sw_110_clk_out, sw_110_data_out, sw_110_scan_out, sw_110_latch_out;
    wire [7:0] sw_110_module_data_in;
    wire [7:0] sw_110_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_110 (
        .clk_in          (sw_109_clk_out),
        .data_in         (sw_109_data_out),
        .scan_select_in  (sw_109_scan_out),
        .latch_enable_in (sw_109_latch_out),
        .clk_out         (sw_110_clk_out),
        .data_out        (sw_110_data_out),
        .scan_select_out (sw_110_scan_out),
        .latch_enable_out(sw_110_latch_out),
        .module_data_in  (sw_110_module_data_in),
        .module_data_out (sw_110_module_data_out)
    );

    vaishnavachath_rotary_toplevel vaishnavachath_rotary_toplevel_110 (
        .io_in  (sw_110_module_data_in),
        .io_out (sw_110_module_data_out)
    );

    // [111] https://github.com/maehw/tt02-wokwi-wolf-goat-cabbage
    wire sw_111_clk_out, sw_111_data_out, sw_111_scan_out, sw_111_latch_out;
    wire [7:0] sw_111_module_data_in;
    wire [7:0] sw_111_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_111 (
        .clk_in          (sw_110_clk_out),
        .data_in         (sw_110_data_out),
        .scan_select_in  (sw_110_scan_out),
        .latch_enable_in (sw_110_latch_out),
        .clk_out         (sw_111_clk_out),
        .data_out        (sw_111_data_out),
        .scan_select_out (sw_111_scan_out),
        .latch_enable_out(sw_111_latch_out),
        .module_data_in  (sw_111_module_data_in),
        .module_data_out (sw_111_module_data_out)
    );

    user_module_341614346808328788 user_module_341614346808328788_111 (
        .io_in  (sw_111_module_data_in),
        .io_out (sw_111_module_data_out)
    );

    // [112] https://github.com/maehw/tt02-wokwi-lowspeed-tiny-uart
    wire sw_112_clk_out, sw_112_data_out, sw_112_scan_out, sw_112_latch_out;
    wire [7:0] sw_112_module_data_in;
    wire [7:0] sw_112_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_112 (
        .clk_in          (sw_111_clk_out),
        .data_in         (sw_111_data_out),
        .scan_select_in  (sw_111_scan_out),
        .latch_enable_in (sw_111_latch_out),
        .clk_out         (sw_112_clk_out),
        .data_out        (sw_112_data_out),
        .scan_select_out (sw_112_scan_out),
        .latch_enable_out(sw_112_latch_out),
        .module_data_in  (sw_112_module_data_in),
        .module_data_out (sw_112_module_data_out)
    );

    user_module_341631511790879314 user_module_341631511790879314_112 (
        .io_in  (sw_112_module_data_in),
        .io_out (sw_112_module_data_out)
    );

    // [113] https://github.com/wimdams/tt02-rotary-encoder
    wire sw_113_clk_out, sw_113_data_out, sw_113_scan_out, sw_113_latch_out;
    wire [7:0] sw_113_module_data_in;
    wire [7:0] sw_113_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_113 (
        .clk_in          (sw_112_clk_out),
        .data_in         (sw_112_data_out),
        .scan_select_in  (sw_112_scan_out),
        .latch_enable_in (sw_112_latch_out),
        .clk_out         (sw_113_clk_out),
        .data_out        (sw_113_data_out),
        .scan_select_out (sw_113_scan_out),
        .latch_enable_out(sw_113_latch_out),
        .module_data_in  (sw_113_module_data_in),
        .module_data_out (sw_113_module_data_out)
    );

    rotary_encoder rotary_encoder_113 (
        .io_in  (sw_113_module_data_in),
        .io_out (sw_113_module_data_out)
    );

    // [114] https://github.com/ChrisPVille/tt02-FROG4bitCPU
    wire sw_114_clk_out, sw_114_data_out, sw_114_scan_out, sw_114_latch_out;
    wire [7:0] sw_114_module_data_in;
    wire [7:0] sw_114_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_114 (
        .clk_in          (sw_113_clk_out),
        .data_in         (sw_113_data_out),
        .scan_select_in  (sw_113_scan_out),
        .latch_enable_in (sw_113_latch_out),
        .clk_out         (sw_114_clk_out),
        .data_out        (sw_114_data_out),
        .scan_select_out (sw_114_scan_out),
        .latch_enable_out(sw_114_latch_out),
        .module_data_in  (sw_114_module_data_in),
        .module_data_out (sw_114_module_data_out)
    );

    frog frog_114 (
        .io_in  (sw_114_module_data_in),
        .io_out (sw_114_module_data_out)
    );

    // [115] https://github.com/swalense/tt02-graycode_counter
    wire sw_115_clk_out, sw_115_data_out, sw_115_scan_out, sw_115_latch_out;
    wire [7:0] sw_115_module_data_in;
    wire [7:0] sw_115_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_115 (
        .clk_in          (sw_114_clk_out),
        .data_in         (sw_114_data_out),
        .scan_select_in  (sw_114_scan_out),
        .latch_enable_in (sw_114_latch_out),
        .clk_out         (sw_115_clk_out),
        .data_out        (sw_115_data_out),
        .scan_select_out (sw_115_scan_out),
        .latch_enable_out(sw_115_latch_out),
        .module_data_in  (sw_115_module_data_in),
        .module_data_out (sw_115_module_data_out)
    );

    swalense_top swalense_top_115 (
        .io_in  (sw_115_module_data_in),
        .io_out (sw_115_module_data_out)
    );

    // [116] https://github.com/Luthor2k/tt02-baudot
    wire sw_116_clk_out, sw_116_data_out, sw_116_scan_out, sw_116_latch_out;
    wire [7:0] sw_116_module_data_in;
    wire [7:0] sw_116_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_116 (
        .clk_in          (sw_115_clk_out),
        .data_in         (sw_115_data_out),
        .scan_select_in  (sw_115_scan_out),
        .latch_enable_in (sw_115_latch_out),
        .clk_out         (sw_116_clk_out),
        .data_out        (sw_116_data_out),
        .scan_select_out (sw_116_scan_out),
        .latch_enable_out(sw_116_latch_out),
        .module_data_in  (sw_116_module_data_in),
        .module_data_out (sw_116_module_data_out)
    );

    luthor2k_top_tto luthor2k_top_tto_116 (
        .io_in  (sw_116_module_data_in),
        .io_out (sw_116_module_data_out)
    );

    // [117] https://github.com/ctag/tt02-submission-ctag
    wire sw_117_clk_out, sw_117_data_out, sw_117_scan_out, sw_117_latch_out;
    wire [7:0] sw_117_module_data_in;
    wire [7:0] sw_117_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_117 (
        .clk_in          (sw_116_clk_out),
        .data_in         (sw_116_data_out),
        .scan_select_in  (sw_116_scan_out),
        .latch_enable_in (sw_116_latch_out),
        .clk_out         (sw_117_clk_out),
        .data_out        (sw_117_data_out),
        .scan_select_out (sw_117_scan_out),
        .latch_enable_out(sw_117_latch_out),
        .module_data_in  (sw_117_module_data_in),
        .module_data_out (sw_117_module_data_out)
    );

    user_module_349886696875098706 user_module_349886696875098706_117 (
        .io_in  (sw_117_module_data_in),
        .io_out (sw_117_module_data_out)
    );

    // [118] https://github.com/AsmaMohsin1507/tt02-channel-coding
    wire sw_118_clk_out, sw_118_data_out, sw_118_scan_out, sw_118_latch_out;
    wire [7:0] sw_118_module_data_in;
    wire [7:0] sw_118_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_118 (
        .clk_in          (sw_117_clk_out),
        .data_in         (sw_117_data_out),
        .scan_select_in  (sw_117_scan_out),
        .latch_enable_in (sw_117_latch_out),
        .clk_out         (sw_118_clk_out),
        .data_out        (sw_118_data_out),
        .scan_select_out (sw_118_scan_out),
        .latch_enable_out(sw_118_latch_out),
        .module_data_in  (sw_118_module_data_in),
        .module_data_out (sw_118_module_data_out)
    );

    Asma_Mohsin_conv_enc_core Asma_Mohsin_conv_enc_core_118 (
        .io_in  (sw_118_module_data_in),
        .io_out (sw_118_module_data_out)
    );

    // [119] https://github.com/stevenmburns/tt02-scannable-gcd
    wire sw_119_clk_out, sw_119_data_out, sw_119_scan_out, sw_119_latch_out;
    wire [7:0] sw_119_module_data_in;
    wire [7:0] sw_119_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_119 (
        .clk_in          (sw_118_clk_out),
        .data_in         (sw_118_data_out),
        .scan_select_in  (sw_118_scan_out),
        .latch_enable_in (sw_118_latch_out),
        .clk_out         (sw_119_clk_out),
        .data_out        (sw_119_data_out),
        .scan_select_out (sw_119_scan_out),
        .latch_enable_out(sw_119_latch_out),
        .module_data_in  (sw_119_module_data_in),
        .module_data_out (sw_119_module_data_out)
    );

    stevenmburns_toplevel stevenmburns_toplevel_119 (
        .io_in  (sw_119_module_data_in),
        .io_out (sw_119_module_data_out)
    );

    // [120] https://github.com/cy384/tt02-submission-template
    wire sw_120_clk_out, sw_120_data_out, sw_120_scan_out, sw_120_latch_out;
    wire [7:0] sw_120_module_data_in;
    wire [7:0] sw_120_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_120 (
        .clk_in          (sw_119_clk_out),
        .data_in         (sw_119_data_out),
        .scan_select_in  (sw_119_scan_out),
        .latch_enable_in (sw_119_latch_out),
        .clk_out         (sw_120_clk_out),
        .data_out        (sw_120_data_out),
        .scan_select_out (sw_120_scan_out),
        .latch_enable_out(sw_120_latch_out),
        .module_data_in  (sw_120_module_data_in),
        .module_data_out (sw_120_module_data_out)
    );

    user_module_341546888233747026 user_module_341546888233747026_120 (
        .io_in  (sw_120_module_data_in),
        .io_out (sw_120_module_data_out)
    );

    // [121] https://github.com/rglenn/tt02-rglenn-hex-to-7-seg
    wire sw_121_clk_out, sw_121_data_out, sw_121_scan_out, sw_121_latch_out;
    wire [7:0] sw_121_module_data_in;
    wire [7:0] sw_121_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_121 (
        .clk_in          (sw_120_clk_out),
        .data_in         (sw_120_data_out),
        .scan_select_in  (sw_120_scan_out),
        .latch_enable_in (sw_120_latch_out),
        .clk_out         (sw_121_clk_out),
        .data_out        (sw_121_data_out),
        .scan_select_out (sw_121_scan_out),
        .latch_enable_out(sw_121_latch_out),
        .module_data_in  (sw_121_module_data_in),
        .module_data_out (sw_121_module_data_out)
    );

    rglenn_hex_to_7_seg rglenn_hex_to_7_seg_121 (
        .io_in  (sw_121_module_data_in),
        .io_out (sw_121_module_data_out)
    );

    // [122] https://github.com/zymason/tt02-zymason
    wire sw_122_clk_out, sw_122_data_out, sw_122_scan_out, sw_122_latch_out;
    wire [7:0] sw_122_module_data_in;
    wire [7:0] sw_122_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_122 (
        .clk_in          (sw_121_clk_out),
        .data_in         (sw_121_data_out),
        .scan_select_in  (sw_121_scan_out),
        .latch_enable_in (sw_121_latch_out),
        .clk_out         (sw_122_clk_out),
        .data_out        (sw_122_data_out),
        .scan_select_out (sw_122_scan_out),
        .latch_enable_out(sw_122_latch_out),
        .module_data_in  (sw_122_module_data_in),
        .module_data_out (sw_122_module_data_out)
    );

    zymason_tinytop zymason_tinytop_122 (
        .io_in  (sw_122_module_data_in),
        .io_out (sw_122_module_data_out)
    );

    // [123] https://github.com/DaveyPocket/chaser_tt2
    wire sw_123_clk_out, sw_123_data_out, sw_123_scan_out, sw_123_latch_out;
    wire [7:0] sw_123_module_data_in;
    wire [7:0] sw_123_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_123 (
        .clk_in          (sw_122_clk_out),
        .data_in         (sw_122_data_out),
        .scan_select_in  (sw_122_scan_out),
        .latch_enable_in (sw_122_latch_out),
        .clk_out         (sw_123_clk_out),
        .data_out        (sw_123_data_out),
        .scan_select_out (sw_123_scan_out),
        .latch_enable_out(sw_123_latch_out),
        .module_data_in  (sw_123_module_data_in),
        .module_data_out (sw_123_module_data_out)
    );

    user_module_341178481588044372 user_module_341178481588044372_123 (
        .io_in  (sw_123_module_data_in),
        .io_out (sw_123_module_data_out)
    );

    // [124] https://github.com/klei22/Rolling-Average
    wire sw_124_clk_out, sw_124_data_out, sw_124_scan_out, sw_124_latch_out;
    wire [7:0] sw_124_module_data_in;
    wire [7:0] sw_124_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_124 (
        .clk_in          (sw_123_clk_out),
        .data_in         (sw_123_data_out),
        .scan_select_in  (sw_123_scan_out),
        .latch_enable_in (sw_123_latch_out),
        .clk_out         (sw_124_clk_out),
        .data_out        (sw_124_data_out),
        .scan_select_out (sw_124_scan_out),
        .latch_enable_out(sw_124_latch_out),
        .module_data_in  (sw_124_module_data_in),
        .module_data_out (sw_124_module_data_out)
    );

    klei22_ra klei22_ra_124 (
        .io_in  (sw_124_module_data_in),
        .io_out (sw_124_module_data_out)
    );

    // [125] https://github.com/andars/tt02-universal-turing-machine-w5s8
    wire sw_125_clk_out, sw_125_data_out, sw_125_scan_out, sw_125_latch_out;
    wire [7:0] sw_125_module_data_in;
    wire [7:0] sw_125_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_125 (
        .clk_in          (sw_124_clk_out),
        .data_in         (sw_124_data_out),
        .scan_select_in  (sw_124_scan_out),
        .latch_enable_in (sw_124_latch_out),
        .clk_out         (sw_125_clk_out),
        .data_out        (sw_125_data_out),
        .scan_select_out (sw_125_scan_out),
        .latch_enable_out(sw_125_latch_out),
        .module_data_in  (sw_125_module_data_in),
        .module_data_out (sw_125_module_data_out)
    );

    afoote_w5s8_tt02_top afoote_w5s8_tt02_top_125 (
        .io_in  (sw_125_module_data_in),
        .io_out (sw_125_module_data_out)
    );

    // [126] https://github.com/ternary-info/tt02-submission-shaos3
    wire sw_126_clk_out, sw_126_data_out, sw_126_scan_out, sw_126_latch_out;
    wire [7:0] sw_126_module_data_in;
    wire [7:0] sw_126_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_126 (
        .clk_in          (sw_125_clk_out),
        .data_in         (sw_125_data_out),
        .scan_select_in  (sw_125_scan_out),
        .latch_enable_in (sw_125_latch_out),
        .clk_out         (sw_126_clk_out),
        .data_out        (sw_126_data_out),
        .scan_select_out (sw_126_scan_out),
        .latch_enable_out(sw_126_latch_out),
        .module_data_in  (sw_126_module_data_in),
        .module_data_out (sw_126_module_data_out)
    );

    user_module_349255310782759507 user_module_349255310782759507_126 (
        .io_in  (sw_126_module_data_in),
        .io_out (sw_126_module_data_out)
    );

    // [127] https://github.com/gregdavill/tt02-clock
    wire sw_127_clk_out, sw_127_data_out, sw_127_scan_out, sw_127_latch_out;
    wire [7:0] sw_127_module_data_in;
    wire [7:0] sw_127_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_127 (
        .clk_in          (sw_126_clk_out),
        .data_in         (sw_126_data_out),
        .scan_select_in  (sw_126_scan_out),
        .latch_enable_in (sw_126_latch_out),
        .clk_out         (sw_127_clk_out),
        .data_out        (sw_127_data_out),
        .scan_select_out (sw_127_scan_out),
        .latch_enable_out(sw_127_latch_out),
        .module_data_in  (sw_127_module_data_in),
        .module_data_out (sw_127_module_data_out)
    );

    gregdavill_clock_top gregdavill_clock_top_127 (
        .io_in  (sw_127_module_data_in),
        .io_out (sw_127_module_data_out)
    );

    // [128] https://github.com/gregdavill/tt02-serv
    wire sw_128_clk_out, sw_128_data_out, sw_128_scan_out, sw_128_latch_out;
    wire [7:0] sw_128_module_data_in;
    wire [7:0] sw_128_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_128 (
        .clk_in          (sw_127_clk_out),
        .data_in         (sw_127_data_out),
        .scan_select_in  (sw_127_scan_out),
        .latch_enable_in (sw_127_latch_out),
        .clk_out         (sw_128_clk_out),
        .data_out        (sw_128_data_out),
        .scan_select_out (sw_128_scan_out),
        .latch_enable_out(sw_128_latch_out),
        .module_data_in  (sw_128_module_data_in),
        .module_data_out (sw_128_module_data_out)
    );

    gregdavill_serv_top gregdavill_serv_top_128 (
        .io_in  (sw_128_module_data_in),
        .io_out (sw_128_module_data_out)
    );

    // [129] https://github.com/saicharan0112/tt02-submission-template
    wire sw_129_clk_out, sw_129_data_out, sw_129_scan_out, sw_129_latch_out;
    wire [7:0] sw_129_module_data_in;
    wire [7:0] sw_129_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_129 (
        .clk_in          (sw_128_clk_out),
        .data_in         (sw_128_data_out),
        .scan_select_in  (sw_128_scan_out),
        .latch_enable_in (sw_128_latch_out),
        .clk_out         (sw_129_clk_out),
        .data_out        (sw_129_data_out),
        .scan_select_out (sw_129_scan_out),
        .latch_enable_out(sw_129_latch_out),
        .module_data_in  (sw_129_module_data_in),
        .module_data_out (sw_129_module_data_out)
    );

    user_module_349813388252021330 user_module_349813388252021330_129 (
        .io_in  (sw_129_module_data_in),
        .io_out (sw_129_module_data_out)
    );

    // [130] https://github.com/tanishnk/Tiny-Tapeout-2-submission-Tanish-k
    wire sw_130_clk_out, sw_130_data_out, sw_130_scan_out, sw_130_latch_out;
    wire [7:0] sw_130_module_data_in;
    wire [7:0] sw_130_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_130 (
        .clk_in          (sw_129_clk_out),
        .data_in         (sw_129_data_out),
        .scan_select_in  (sw_129_scan_out),
        .latch_enable_in (sw_129_latch_out),
        .clk_out         (sw_130_clk_out),
        .data_out        (sw_130_data_out),
        .scan_select_out (sw_130_scan_out),
        .latch_enable_out(sw_130_latch_out),
        .module_data_in  (sw_130_module_data_in),
        .module_data_out (sw_130_module_data_out)
    );

    user_module_349934460979905106 user_module_349934460979905106_130 (
        .io_in  (sw_130_module_data_in),
        .io_out (sw_130_module_data_out)
    );

    // [131] https://github.com/skylersaleh/tt02-hello
    wire sw_131_clk_out, sw_131_data_out, sw_131_scan_out, sw_131_latch_out;
    wire [7:0] sw_131_module_data_in;
    wire [7:0] sw_131_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_131 (
        .clk_in          (sw_130_clk_out),
        .data_in         (sw_130_data_out),
        .scan_select_in  (sw_130_scan_out),
        .latch_enable_in (sw_130_latch_out),
        .clk_out         (sw_131_clk_out),
        .data_out        (sw_131_data_out),
        .scan_select_out (sw_131_scan_out),
        .latch_enable_out(sw_131_latch_out),
        .module_data_in  (sw_131_module_data_in),
        .module_data_out (sw_131_module_data_out)
    );

    user_module_skylersaleh user_module_skylersaleh_131 (
        .io_in  (sw_131_module_data_in),
        .io_out (sw_131_module_data_out)
    );

    // [132] https://github.com/BarsMonster/MicroAsicVI
    wire sw_132_clk_out, sw_132_data_out, sw_132_scan_out, sw_132_latch_out;
    wire [7:0] sw_132_module_data_in;
    wire [7:0] sw_132_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_132 (
        .clk_in          (sw_131_clk_out),
        .data_in         (sw_131_data_out),
        .scan_select_in  (sw_131_scan_out),
        .latch_enable_in (sw_131_latch_out),
        .clk_out         (sw_132_clk_out),
        .data_out        (sw_132_data_out),
        .scan_select_out (sw_132_scan_out),
        .latch_enable_out(sw_132_latch_out),
        .module_data_in  (sw_132_module_data_in),
        .module_data_out (sw_132_module_data_out)
    );

    user_module_341628725785264722 user_module_341628725785264722_132 (
        .io_in  (sw_132_module_data_in),
        .io_out (sw_132_module_data_out)
    );

    // [133] https://github.com/RecepSaid/tt02-euclidean-algorithm
    wire sw_133_clk_out, sw_133_data_out, sw_133_scan_out, sw_133_latch_out;
    wire [7:0] sw_133_module_data_in;
    wire [7:0] sw_133_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_133 (
        .clk_in          (sw_132_clk_out),
        .data_in         (sw_132_data_out),
        .scan_select_in  (sw_132_scan_out),
        .latch_enable_in (sw_132_latch_out),
        .clk_out         (sw_133_clk_out),
        .data_out        (sw_133_data_out),
        .scan_select_out (sw_133_scan_out),
        .latch_enable_out(sw_133_latch_out),
        .module_data_in  (sw_133_module_data_in),
        .module_data_out (sw_133_module_data_out)
    );

    recepsaid_euclidean_algorithm recepsaid_euclidean_algorithm_133 (
        .io_in  (sw_133_module_data_in),
        .io_out (sw_133_module_data_out)
    );

    // [134] https://github.com/8086net/tt02-CRC16
    wire sw_134_clk_out, sw_134_data_out, sw_134_scan_out, sw_134_latch_out;
    wire [7:0] sw_134_module_data_in;
    wire [7:0] sw_134_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_134 (
        .clk_in          (sw_133_clk_out),
        .data_in         (sw_133_data_out),
        .scan_select_in  (sw_133_scan_out),
        .latch_enable_in (sw_133_latch_out),
        .clk_out         (sw_134_clk_out),
        .data_out        (sw_134_data_out),
        .scan_select_out (sw_134_scan_out),
        .latch_enable_out(sw_134_latch_out),
        .module_data_in  (sw_134_module_data_in),
        .module_data_out (sw_134_module_data_out)
    );

    user_module_349833797657690706 user_module_349833797657690706_134 (
        .io_in  (sw_134_module_data_in),
        .io_out (sw_134_module_data_out)
    );

    // [135] https://github.com/mazensaghir/tt02-sevsegfx
    wire sw_135_clk_out, sw_135_data_out, sw_135_scan_out, sw_135_latch_out;
    wire [7:0] sw_135_module_data_in;
    wire [7:0] sw_135_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_135 (
        .clk_in          (sw_134_clk_out),
        .data_in         (sw_134_data_out),
        .scan_select_in  (sw_134_scan_out),
        .latch_enable_in (sw_134_latch_out),
        .clk_out         (sw_135_clk_out),
        .data_out        (sw_135_data_out),
        .scan_select_out (sw_135_scan_out),
        .latch_enable_out(sw_135_latch_out),
        .module_data_in  (sw_135_module_data_in),
        .module_data_out (sw_135_module_data_out)
    );

    msaghir_top_level msaghir_top_level_135 (
        .io_in  (sw_135_module_data_in),
        .io_out (sw_135_module_data_out)
    );

    // [136] https://github.com/tzachari/tt02-lab11
    wire sw_136_clk_out, sw_136_data_out, sw_136_scan_out, sw_136_latch_out;
    wire [7:0] sw_136_module_data_in;
    wire [7:0] sw_136_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_136 (
        .clk_in          (sw_135_clk_out),
        .data_in         (sw_135_data_out),
        .scan_select_in  (sw_135_scan_out),
        .latch_enable_in (sw_135_latch_out),
        .clk_out         (sw_136_clk_out),
        .data_out        (sw_136_data_out),
        .scan_select_out (sw_136_scan_out),
        .latch_enable_out(sw_136_latch_out),
        .module_data_in  (sw_136_module_data_in),
        .module_data_out (sw_136_module_data_out)
    );

    user_module_341631644820570706 user_module_341631644820570706_136 (
        .io_in  (sw_136_module_data_in),
        .io_out (sw_136_module_data_out)
    );

    // [137] https://github.com/bitluni/tt02-option23ser
    wire sw_137_clk_out, sw_137_data_out, sw_137_scan_out, sw_137_latch_out;
    wire [7:0] sw_137_module_data_in;
    wire [7:0] sw_137_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_137 (
        .clk_in          (sw_136_clk_out),
        .data_in         (sw_136_data_out),
        .scan_select_in  (sw_136_scan_out),
        .latch_enable_in (sw_136_latch_out),
        .clk_out         (sw_137_clk_out),
        .data_out        (sw_137_data_out),
        .scan_select_out (sw_137_scan_out),
        .latch_enable_out(sw_137_latch_out),
        .module_data_in  (sw_137_module_data_in),
        .module_data_out (sw_137_module_data_out)
    );

    option23ser option23ser_137 (
        .io_in  (sw_137_module_data_in),
        .io_out (sw_137_module_data_out)
    );

    // [138] https://github.com/bitluni/tt02-option23
    wire sw_138_clk_out, sw_138_data_out, sw_138_scan_out, sw_138_latch_out;
    wire [7:0] sw_138_module_data_in;
    wire [7:0] sw_138_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_138 (
        .clk_in          (sw_137_clk_out),
        .data_in         (sw_137_data_out),
        .scan_select_in  (sw_137_scan_out),
        .latch_enable_in (sw_137_latch_out),
        .clk_out         (sw_138_clk_out),
        .data_out        (sw_138_data_out),
        .scan_select_out (sw_138_scan_out),
        .latch_enable_out(sw_138_latch_out),
        .module_data_in  (sw_138_module_data_in),
        .module_data_out (sw_138_module_data_out)
    );

    option23 option23_138 (
        .io_in  (sw_138_module_data_in),
        .io_out (sw_138_module_data_out)
    );

    // [139] https://github.com/bitluni/tt02-option22
    wire sw_139_clk_out, sw_139_data_out, sw_139_scan_out, sw_139_latch_out;
    wire [7:0] sw_139_module_data_in;
    wire [7:0] sw_139_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_139 (
        .clk_in          (sw_138_clk_out),
        .data_in         (sw_138_data_out),
        .scan_select_in  (sw_138_scan_out),
        .latch_enable_in (sw_138_latch_out),
        .clk_out         (sw_139_clk_out),
        .data_out        (sw_139_data_out),
        .scan_select_out (sw_139_scan_out),
        .latch_enable_out(sw_139_latch_out),
        .module_data_in  (sw_139_module_data_in),
        .module_data_out (sw_139_module_data_out)
    );

    option22 option22_139 (
        .io_in  (sw_139_module_data_in),
        .io_out (sw_139_module_data_out)
    );

    // [140] https://github.com/theFestest/tt02-4x4-ram
    wire sw_140_clk_out, sw_140_data_out, sw_140_scan_out, sw_140_latch_out;
    wire [7:0] sw_140_module_data_in;
    wire [7:0] sw_140_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_140 (
        .clk_in          (sw_139_clk_out),
        .data_in         (sw_139_data_out),
        .scan_select_in  (sw_139_scan_out),
        .latch_enable_in (sw_139_latch_out),
        .clk_out         (sw_140_clk_out),
        .data_out        (sw_140_data_out),
        .scan_select_out (sw_140_scan_out),
        .latch_enable_out(sw_140_latch_out),
        .module_data_in  (sw_140_module_data_in),
        .module_data_out (sw_140_module_data_out)
    );

    user_module_341557831870186068 user_module_341557831870186068_140 (
        .io_in  (sw_140_module_data_in),
        .io_out (sw_140_module_data_out)
    );

    // [141] https://github.com/jeanthom/tinytapout-lock
    wire sw_141_clk_out, sw_141_data_out, sw_141_scan_out, sw_141_latch_out;
    wire [7:0] sw_141_module_data_in;
    wire [7:0] sw_141_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_141 (
        .clk_in          (sw_140_clk_out),
        .data_in         (sw_140_data_out),
        .scan_select_in  (sw_140_scan_out),
        .latch_enable_in (sw_140_latch_out),
        .clk_out         (sw_141_clk_out),
        .data_out        (sw_141_data_out),
        .scan_select_out (sw_141_scan_out),
        .latch_enable_out(sw_141_latch_out),
        .module_data_in  (sw_141_module_data_in),
        .module_data_out (sw_141_module_data_out)
    );

    user_module_341438392303616596 user_module_341438392303616596_141 (
        .io_in  (sw_141_module_data_in),
        .io_out (sw_141_module_data_out)
    );

    // [142] https://github.com/jdrosent/tt02-submission-template
    wire sw_142_clk_out, sw_142_data_out, sw_142_scan_out, sw_142_latch_out;
    wire [7:0] sw_142_module_data_in;
    wire [7:0] sw_142_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_142 (
        .clk_in          (sw_141_clk_out),
        .data_in         (sw_141_data_out),
        .scan_select_in  (sw_141_scan_out),
        .latch_enable_in (sw_141_latch_out),
        .clk_out         (sw_142_clk_out),
        .data_out        (sw_142_data_out),
        .scan_select_out (sw_142_scan_out),
        .latch_enable_out(sw_142_latch_out),
        .module_data_in  (sw_142_module_data_in),
        .module_data_out (sw_142_module_data_out)
    );

    user_module_349952820323025491 user_module_349952820323025491_142 (
        .io_in  (sw_142_module_data_in),
        .io_out (sw_142_module_data_out)
    );

    // [143] https://github.com/majdiabdulsamad/tt02-Femto
    wire sw_143_clk_out, sw_143_data_out, sw_143_scan_out, sw_143_latch_out;
    wire [7:0] sw_143_module_data_in;
    wire [7:0] sw_143_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_143 (
        .clk_in          (sw_142_clk_out),
        .data_in         (sw_142_data_out),
        .scan_select_in  (sw_142_scan_out),
        .latch_enable_in (sw_142_latch_out),
        .clk_out         (sw_143_clk_out),
        .data_out        (sw_143_data_out),
        .scan_select_out (sw_143_scan_out),
        .latch_enable_out(sw_143_latch_out),
        .module_data_in  (sw_143_module_data_in),
        .module_data_out (sw_143_module_data_out)
    );

    femto_top femto_top_143 (
        .io_in  (sw_143_module_data_in),
        .io_out (sw_143_module_data_out)
    );

    // [144] https://github.com/AvalonSemiconductors/tt02-logisim-example
    wire sw_144_clk_out, sw_144_data_out, sw_144_scan_out, sw_144_latch_out;
    wire [7:0] sw_144_module_data_in;
    wire [7:0] sw_144_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_144 (
        .clk_in          (sw_143_clk_out),
        .data_in         (sw_143_data_out),
        .scan_select_in  (sw_143_scan_out),
        .latch_enable_in (sw_143_latch_out),
        .clk_out         (sw_144_clk_out),
        .data_out        (sw_144_data_out),
        .scan_select_out (sw_144_scan_out),
        .latch_enable_out(sw_144_latch_out),
        .module_data_in  (sw_144_module_data_in),
        .module_data_out (sw_144_module_data_out)
    );

    logisim_demo logisim_demo_144 (
        .io_in  (sw_144_module_data_in),
        .io_out (sw_144_module_data_out)
    );

    // [145] https://github.com/bitluni/tt02-SecretFile
    wire sw_145_clk_out, sw_145_data_out, sw_145_scan_out, sw_145_latch_out;
    wire [7:0] sw_145_module_data_in;
    wire [7:0] sw_145_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_145 (
        .clk_in          (sw_144_clk_out),
        .data_in         (sw_144_data_out),
        .scan_select_in  (sw_144_scan_out),
        .latch_enable_in (sw_144_latch_out),
        .clk_out         (sw_145_clk_out),
        .data_out        (sw_145_data_out),
        .scan_select_out (sw_145_scan_out),
        .latch_enable_out(sw_145_latch_out),
        .module_data_in  (sw_145_module_data_in),
        .module_data_out (sw_145_module_data_out)
    );

    secretFile secretFile_145 (
        .io_in  (sw_145_module_data_in),
        .io_out (sw_145_module_data_out)
    );

    // [146] https://github.com/cmu-stuco-98154/f22-tt02-qilins
    wire sw_146_clk_out, sw_146_data_out, sw_146_scan_out, sw_146_latch_out;
    wire [7:0] sw_146_module_data_in;
    wire [7:0] sw_146_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_146 (
        .clk_in          (sw_145_clk_out),
        .data_in         (sw_145_data_out),
        .scan_select_in  (sw_145_scan_out),
        .latch_enable_in (sw_145_latch_out),
        .clk_out         (sw_146_clk_out),
        .data_out        (sw_146_data_out),
        .scan_select_out (sw_146_scan_out),
        .latch_enable_out(sw_146_latch_out),
        .module_data_in  (sw_146_module_data_in),
        .module_data_out (sw_146_module_data_out)
    );

    user_module_349519263900369490 user_module_349519263900369490_146 (
        .io_in  (sw_146_module_data_in),
        .io_out (sw_146_module_data_out)
    );

    // [147] https://github.com/cmu-stuco-98154/f22-tt02-jxlu
    wire sw_147_clk_out, sw_147_data_out, sw_147_scan_out, sw_147_latch_out;
    wire [7:0] sw_147_module_data_in;
    wire [7:0] sw_147_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_147 (
        .clk_in          (sw_146_clk_out),
        .data_in         (sw_146_data_out),
        .scan_select_in  (sw_146_scan_out),
        .latch_enable_in (sw_146_latch_out),
        .clk_out         (sw_147_clk_out),
        .data_out        (sw_147_data_out),
        .scan_select_out (sw_147_scan_out),
        .latch_enable_out(sw_147_latch_out),
        .module_data_in  (sw_147_module_data_in),
        .module_data_out (sw_147_module_data_out)
    );

    poisonninja_top poisonninja_top_147 (
        .io_in  (sw_147_module_data_in),
        .io_out (sw_147_module_data_out)
    );

    // [148] https://github.com/cmu-stuco-98154/f22-tt02-mgee3
    wire sw_148_clk_out, sw_148_data_out, sw_148_scan_out, sw_148_latch_out;
    wire [7:0] sw_148_module_data_in;
    wire [7:0] sw_148_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_148 (
        .clk_in          (sw_147_clk_out),
        .data_in         (sw_147_data_out),
        .scan_select_in  (sw_147_scan_out),
        .latch_enable_in (sw_147_latch_out),
        .clk_out         (sw_148_clk_out),
        .data_out        (sw_148_data_out),
        .scan_select_out (sw_148_scan_out),
        .latch_enable_out(sw_148_latch_out),
        .module_data_in  (sw_148_module_data_in),
        .module_data_out (sw_148_module_data_out)
    );

    user_module_349803790984020562 user_module_349803790984020562_148 (
        .io_in  (sw_148_module_data_in),
        .io_out (sw_148_module_data_out)
    );

    // [149] https://github.com/cmu-stuco-98154/f22-tt02-sophiali
    wire sw_149_clk_out, sw_149_data_out, sw_149_scan_out, sw_149_latch_out;
    wire [7:0] sw_149_module_data_in;
    wire [7:0] sw_149_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_149 (
        .clk_in          (sw_148_clk_out),
        .data_in         (sw_148_data_out),
        .scan_select_in  (sw_148_scan_out),
        .latch_enable_in (sw_148_latch_out),
        .clk_out         (sw_149_clk_out),
        .data_out        (sw_149_data_out),
        .scan_select_out (sw_149_scan_out),
        .latch_enable_out(sw_149_latch_out),
        .module_data_in  (sw_149_module_data_in),
        .module_data_out (sw_149_module_data_out)
    );

    sophialiCMU_math sophialiCMU_math_149 (
        .io_in  (sw_149_module_data_in),
        .io_out (sw_149_module_data_out)
    );

    // [150] https://github.com/cmu-stuco-98154/f22-tt02-jrecta
    wire sw_150_clk_out, sw_150_data_out, sw_150_scan_out, sw_150_latch_out;
    wire [7:0] sw_150_module_data_in;
    wire [7:0] sw_150_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_150 (
        .clk_in          (sw_149_clk_out),
        .data_in         (sw_149_data_out),
        .scan_select_in  (sw_149_scan_out),
        .latch_enable_in (sw_149_latch_out),
        .clk_out         (sw_150_clk_out),
        .data_out        (sw_150_data_out),
        .scan_select_out (sw_150_scan_out),
        .latch_enable_out(sw_150_latch_out),
        .module_data_in  (sw_150_module_data_in),
        .module_data_out (sw_150_module_data_out)
    );

    jonpaolo02_async_fifo jonpaolo02_async_fifo_150 (
        .io_in  (sw_150_module_data_in),
        .io_out (sw_150_module_data_out)
    );

    // [151] https://github.com/asinghani/tt02-beepboop
    wire sw_151_clk_out, sw_151_data_out, sw_151_scan_out, sw_151_latch_out;
    wire [7:0] sw_151_module_data_in;
    wire [7:0] sw_151_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_151 (
        .clk_in          (sw_150_clk_out),
        .data_in         (sw_150_data_out),
        .scan_select_in  (sw_150_scan_out),
        .latch_enable_in (sw_150_latch_out),
        .clk_out         (sw_151_clk_out),
        .data_out        (sw_151_data_out),
        .scan_select_out (sw_151_scan_out),
        .latch_enable_out(sw_151_latch_out),
        .module_data_in  (sw_151_module_data_in),
        .module_data_out (sw_151_module_data_out)
    );

    asinghani_beepboop asinghani_beepboop_151 (
        .io_in  (sw_151_module_data_in),
        .io_out (sw_151_module_data_out)
    );

    // [152] https://github.com/noahgaertner/tt02-verilog-demo
    wire sw_152_clk_out, sw_152_data_out, sw_152_scan_out, sw_152_latch_out;
    wire [7:0] sw_152_module_data_in;
    wire [7:0] sw_152_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_152 (
        .clk_in          (sw_151_clk_out),
        .data_in         (sw_151_data_out),
        .scan_select_in  (sw_151_scan_out),
        .latch_enable_in (sw_151_latch_out),
        .clk_out         (sw_152_clk_out),
        .data_out        (sw_152_data_out),
        .scan_select_out (sw_152_scan_out),
        .latch_enable_out(sw_152_latch_out),
        .module_data_in  (sw_152_module_data_in),
        .module_data_out (sw_152_module_data_out)
    );

    noahgaertner_cpu noahgaertner_cpu_152 (
        .io_in  (sw_152_module_data_in),
        .io_out (sw_152_module_data_out)
    );

    // [153] https://github.com/prabaldutta/tt02-adi-demo
    wire sw_153_clk_out, sw_153_data_out, sw_153_scan_out, sw_153_latch_out;
    wire [7:0] sw_153_module_data_in;
    wire [7:0] sw_153_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_153 (
        .clk_in          (sw_152_clk_out),
        .data_in         (sw_152_data_out),
        .scan_select_in  (sw_152_scan_out),
        .latch_enable_in (sw_152_latch_out),
        .clk_out         (sw_153_clk_out),
        .data_out        (sw_153_data_out),
        .scan_select_out (sw_153_scan_out),
        .latch_enable_out(sw_153_latch_out),
        .module_data_in  (sw_153_module_data_in),
        .module_data_out (sw_153_module_data_out)
    );

    user_module_341613097060926036 user_module_341613097060926036_153 (
        .io_in  (sw_153_module_data_in),
        .io_out (sw_153_module_data_out)
    );

    // [154] https://github.com/TinyTapeout/tt02-tinytapeout-clock-divider-asic
    wire sw_154_clk_out, sw_154_data_out, sw_154_scan_out, sw_154_latch_out;
    wire [7:0] sw_154_module_data_in;
    wire [7:0] sw_154_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_154 (
        .clk_in          (sw_153_clk_out),
        .data_in         (sw_153_data_out),
        .scan_select_in  (sw_153_scan_out),
        .latch_enable_in (sw_153_latch_out),
        .clk_out         (sw_154_clk_out),
        .data_out        (sw_154_data_out),
        .scan_select_out (sw_154_scan_out),
        .latch_enable_out(sw_154_latch_out),
        .module_data_in  (sw_154_module_data_in),
        .module_data_out (sw_154_module_data_out)
    );

    user_module_341353928049295956 user_module_341353928049295956_154 (
        .io_in  (sw_154_module_data_in),
        .io_out (sw_154_module_data_out)
    );

    // [155] https://github.com/tucanae47/tt02-gray-counter
    wire sw_155_clk_out, sw_155_data_out, sw_155_scan_out, sw_155_latch_out;
    wire [7:0] sw_155_module_data_in;
    wire [7:0] sw_155_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_155 (
        .clk_in          (sw_154_clk_out),
        .data_in         (sw_154_data_out),
        .scan_select_in  (sw_154_scan_out),
        .latch_enable_in (sw_154_latch_out),
        .clk_out         (sw_155_clk_out),
        .data_out        (sw_155_data_out),
        .scan_select_out (sw_155_scan_out),
        .latch_enable_out(sw_155_latch_out),
        .module_data_in  (sw_155_module_data_in),
        .module_data_out (sw_155_module_data_out)
    );

    tucanae47_gray_ctr6 tucanae47_gray_ctr6_155 (
        .io_in  (sw_155_module_data_in),
        .io_out (sw_155_module_data_out)
    );

    // [156] https://github.com/TinyTapeout/tt02-test-7seg
    wire sw_156_clk_out, sw_156_data_out, sw_156_scan_out, sw_156_latch_out;
    wire [7:0] sw_156_module_data_in;
    wire [7:0] sw_156_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_156 (
        .clk_in          (sw_155_clk_out),
        .data_in         (sw_155_data_out),
        .scan_select_in  (sw_155_scan_out),
        .latch_enable_in (sw_155_latch_out),
        .clk_out         (sw_156_clk_out),
        .data_out        (sw_156_data_out),
        .scan_select_out (sw_156_scan_out),
        .latch_enable_out(sw_156_latch_out),
        .module_data_in  (sw_156_module_data_in),
        .module_data_out (sw_156_module_data_out)
    );

    user_module_340805072482992722 user_module_340805072482992722_156 (
        .io_in  (sw_156_module_data_in),
        .io_out (sw_156_module_data_out)
    );

    // [157] https://github.com/TinyTapeout/tt02-verilog-demo
    wire sw_157_clk_out, sw_157_data_out, sw_157_scan_out, sw_157_latch_out;
    wire [7:0] sw_157_module_data_in;
    wire [7:0] sw_157_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_157 (
        .clk_in          (sw_156_clk_out),
        .data_in         (sw_156_data_out),
        .scan_select_in  (sw_156_scan_out),
        .latch_enable_in (sw_156_latch_out),
        .clk_out         (sw_157_clk_out),
        .data_out        (sw_157_data_out),
        .scan_select_out (sw_157_scan_out),
        .latch_enable_out(sw_157_latch_out),
        .module_data_in  (sw_157_module_data_in),
        .module_data_out (sw_157_module_data_out)
    );

    seven_segment_seconds seven_segment_seconds_157 (
        .io_in  (sw_157_module_data_in),
        .io_out (sw_157_module_data_out)
    );

    // [158] https://github.com/mattvenn/tt02-laura
    wire sw_158_clk_out, sw_158_data_out, sw_158_scan_out, sw_158_latch_out;
    wire [7:0] sw_158_module_data_in;
    wire [7:0] sw_158_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_158 (
        .clk_in          (sw_157_clk_out),
        .data_in         (sw_157_data_out),
        .scan_select_in  (sw_157_scan_out),
        .latch_enable_in (sw_157_latch_out),
        .clk_out         (sw_158_clk_out),
        .data_out        (sw_158_data_out),
        .scan_select_out (sw_158_scan_out),
        .latch_enable_out(sw_158_latch_out),
        .module_data_in  (sw_158_module_data_in),
        .module_data_out (sw_158_module_data_out)
    );

    user_module_341678527574180436 user_module_341678527574180436_158 (
        .io_in  (sw_158_module_data_in),
        .io_out (sw_158_module_data_out)
    );

    // [159] https://github.com/mattvenn/tt02-m-segments
    wire sw_159_clk_out, sw_159_data_out, sw_159_scan_out, sw_159_latch_out;
    wire [7:0] sw_159_module_data_in;
    wire [7:0] sw_159_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_159 (
        .clk_in          (sw_158_clk_out),
        .data_in         (sw_158_data_out),
        .scan_select_in  (sw_158_scan_out),
        .latch_enable_in (sw_158_latch_out),
        .clk_out         (sw_159_clk_out),
        .data_out        (sw_159_data_out),
        .scan_select_out (sw_159_scan_out),
        .latch_enable_out(sw_159_latch_out),
        .module_data_in  (sw_159_module_data_in),
        .module_data_out (sw_159_module_data_out)
    );

    user_module_339688086163161683 user_module_339688086163161683_159 (
        .io_in  (sw_159_module_data_in),
        .io_out (sw_159_module_data_out)
    );

    // [160] https://github.com/jdrosent/tt02-7segstringdisplay
    wire sw_160_clk_out, sw_160_data_out, sw_160_scan_out, sw_160_latch_out;
    wire [7:0] sw_160_module_data_in;
    wire [7:0] sw_160_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_160 (
        .clk_in          (sw_159_clk_out),
        .data_in         (sw_159_data_out),
        .scan_select_in  (sw_159_scan_out),
        .latch_enable_in (sw_159_latch_out),
        .clk_out         (sw_160_clk_out),
        .data_out        (sw_160_data_out),
        .scan_select_out (sw_160_scan_out),
        .latch_enable_out(sw_160_latch_out),
        .module_data_in  (sw_160_module_data_in),
        .module_data_out (sw_160_module_data_out)
    );

    user_module_347497504164545108 user_module_347497504164545108_160 (
        .io_in  (sw_160_module_data_in),
        .io_out (sw_160_module_data_out)
    );

    // [161] https://github.com/jdrosent/tt02-UARTcharacter
    wire sw_161_clk_out, sw_161_data_out, sw_161_scan_out, sw_161_latch_out;
    wire [7:0] sw_161_module_data_in;
    wire [7:0] sw_161_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_161 (
        .clk_in          (sw_160_clk_out),
        .data_in         (sw_160_data_out),
        .scan_select_in  (sw_160_scan_out),
        .latch_enable_in (sw_160_latch_out),
        .clk_out         (sw_161_clk_out),
        .data_out        (sw_161_data_out),
        .scan_select_out (sw_161_scan_out),
        .latch_enable_out(sw_161_latch_out),
        .module_data_in  (sw_161_module_data_in),
        .module_data_out (sw_161_module_data_out)
    );

    user_module_347140425276981843 user_module_347140425276981843_161 (
        .io_in  (sw_161_module_data_in),
        .io_out (sw_161_module_data_out)
    );

    // [162] https://github.com/jdrosent/tt02-UARTstring
    wire sw_162_clk_out, sw_162_data_out, sw_162_scan_out, sw_162_latch_out;
    wire [7:0] sw_162_module_data_in;
    wire [7:0] sw_162_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_162 (
        .clk_in          (sw_161_clk_out),
        .data_in         (sw_161_data_out),
        .scan_select_in  (sw_161_scan_out),
        .latch_enable_in (sw_161_latch_out),
        .clk_out         (sw_162_clk_out),
        .data_out        (sw_162_data_out),
        .scan_select_out (sw_162_scan_out),
        .latch_enable_out(sw_162_latch_out),
        .module_data_in  (sw_162_module_data_in),
        .module_data_out (sw_162_module_data_out)
    );

    user_module_347144898258928211 user_module_347144898258928211_162 (
        .io_in  (sw_162_module_data_in),
        .io_out (sw_162_module_data_out)
    );

    // [163] https://github.com/jdrosent/tt02-padlock
    wire sw_163_clk_out, sw_163_data_out, sw_163_scan_out, sw_163_latch_out;
    wire [7:0] sw_163_module_data_in;
    wire [7:0] sw_163_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_163 (
        .clk_in          (sw_162_clk_out),
        .data_in         (sw_162_data_out),
        .scan_select_in  (sw_162_scan_out),
        .latch_enable_in (sw_162_latch_out),
        .clk_out         (sw_163_clk_out),
        .data_out        (sw_163_data_out),
        .scan_select_out (sw_163_scan_out),
        .latch_enable_out(sw_163_latch_out),
        .module_data_in  (sw_163_module_data_in),
        .module_data_out (sw_163_module_data_out)
    );

    user_module_347417602591556180 user_module_347417602591556180_163 (
        .io_in  (sw_163_module_data_in),
        .io_out (sw_163_module_data_out)
    );

    // [164] https://github.com/H-Bydn/TinyTapeout2-PWMgenerator
    wire sw_164_clk_out, sw_164_data_out, sw_164_scan_out, sw_164_latch_out;
    wire [7:0] sw_164_module_data_in;
    wire [7:0] sw_164_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_164 (
        .clk_in          (sw_163_clk_out),
        .data_in         (sw_163_data_out),
        .scan_select_in  (sw_163_scan_out),
        .latch_enable_in (sw_163_latch_out),
        .clk_out         (sw_164_clk_out),
        .data_out        (sw_164_data_out),
        .scan_select_out (sw_164_scan_out),
        .latch_enable_out(sw_164_latch_out),
        .module_data_in  (sw_164_module_data_in),
        .module_data_out (sw_164_module_data_out)
    );

    razhas_top_level razhas_top_level_164 (
        .io_in  (sw_164_module_data_in),
        .io_out (sw_164_module_data_out)
    );

    // [165] https://github.com/wokwi/tinytapeout-skullart
    wire sw_165_clk_out, sw_165_data_out, sw_165_scan_out, sw_165_latch_out;
    wire [7:0] sw_165_module_data_in;
    wire [7:0] sw_165_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_165 (
        .clk_in          (sw_164_clk_out),
        .data_in         (sw_164_data_out),
        .scan_select_in  (sw_164_scan_out),
        .latch_enable_in (sw_164_latch_out),
        .clk_out         (sw_165_clk_out),
        .data_out        (sw_165_data_out),
        .scan_select_out (sw_165_scan_out),
        .latch_enable_out(sw_165_latch_out),
        .module_data_in  (sw_165_module_data_in),
        .module_data_out (sw_165_module_data_out)
    );

    skullart skullart_165 (
    );

    // [166] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_166_clk_out, sw_166_data_out, sw_166_scan_out, sw_166_latch_out;
    wire [7:0] sw_166_module_data_in;
    wire [7:0] sw_166_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_166 (
        .clk_in          (sw_165_clk_out),
        .data_in         (sw_165_data_out),
        .scan_select_in  (sw_165_scan_out),
        .latch_enable_in (sw_165_latch_out),
        .clk_out         (sw_166_clk_out),
        .data_out        (sw_166_data_out),
        .scan_select_out (sw_166_scan_out),
        .latch_enable_out(sw_166_latch_out),
        .module_data_in  (sw_166_module_data_in),
        .module_data_out (sw_166_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_166 (
        .io_in  (sw_166_module_data_in),
        .io_out (sw_166_module_data_out)
    );

    // [167] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_167_clk_out, sw_167_data_out, sw_167_scan_out, sw_167_latch_out;
    wire [7:0] sw_167_module_data_in;
    wire [7:0] sw_167_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_167 (
        .clk_in          (sw_166_clk_out),
        .data_in         (sw_166_data_out),
        .scan_select_in  (sw_166_scan_out),
        .latch_enable_in (sw_166_latch_out),
        .clk_out         (sw_167_clk_out),
        .data_out        (sw_167_data_out),
        .scan_select_out (sw_167_scan_out),
        .latch_enable_out(sw_167_latch_out),
        .module_data_in  (sw_167_module_data_in),
        .module_data_out (sw_167_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_167 (
        .io_in  (sw_167_module_data_in),
        .io_out (sw_167_module_data_out)
    );

    // [168] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_168_clk_out, sw_168_data_out, sw_168_scan_out, sw_168_latch_out;
    wire [7:0] sw_168_module_data_in;
    wire [7:0] sw_168_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_168 (
        .clk_in          (sw_167_clk_out),
        .data_in         (sw_167_data_out),
        .scan_select_in  (sw_167_scan_out),
        .latch_enable_in (sw_167_latch_out),
        .clk_out         (sw_168_clk_out),
        .data_out        (sw_168_data_out),
        .scan_select_out (sw_168_scan_out),
        .latch_enable_out(sw_168_latch_out),
        .module_data_in  (sw_168_module_data_in),
        .module_data_out (sw_168_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_168 (
        .io_in  (sw_168_module_data_in),
        .io_out (sw_168_module_data_out)
    );

    // [169] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_169_clk_out, sw_169_data_out, sw_169_scan_out, sw_169_latch_out;
    wire [7:0] sw_169_module_data_in;
    wire [7:0] sw_169_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_169 (
        .clk_in          (sw_168_clk_out),
        .data_in         (sw_168_data_out),
        .scan_select_in  (sw_168_scan_out),
        .latch_enable_in (sw_168_latch_out),
        .clk_out         (sw_169_clk_out),
        .data_out        (sw_169_data_out),
        .scan_select_out (sw_169_scan_out),
        .latch_enable_out(sw_169_latch_out),
        .module_data_in  (sw_169_module_data_in),
        .module_data_out (sw_169_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_169 (
        .io_in  (sw_169_module_data_in),
        .io_out (sw_169_module_data_out)
    );

    // [170] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_170_clk_out, sw_170_data_out, sw_170_scan_out, sw_170_latch_out;
    wire [7:0] sw_170_module_data_in;
    wire [7:0] sw_170_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_170 (
        .clk_in          (sw_169_clk_out),
        .data_in         (sw_169_data_out),
        .scan_select_in  (sw_169_scan_out),
        .latch_enable_in (sw_169_latch_out),
        .clk_out         (sw_170_clk_out),
        .data_out        (sw_170_data_out),
        .scan_select_out (sw_170_scan_out),
        .latch_enable_out(sw_170_latch_out),
        .module_data_in  (sw_170_module_data_in),
        .module_data_out (sw_170_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_170 (
        .io_in  (sw_170_module_data_in),
        .io_out (sw_170_module_data_out)
    );

    // [171] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_171_clk_out, sw_171_data_out, sw_171_scan_out, sw_171_latch_out;
    wire [7:0] sw_171_module_data_in;
    wire [7:0] sw_171_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_171 (
        .clk_in          (sw_170_clk_out),
        .data_in         (sw_170_data_out),
        .scan_select_in  (sw_170_scan_out),
        .latch_enable_in (sw_170_latch_out),
        .clk_out         (sw_171_clk_out),
        .data_out        (sw_171_data_out),
        .scan_select_out (sw_171_scan_out),
        .latch_enable_out(sw_171_latch_out),
        .module_data_in  (sw_171_module_data_in),
        .module_data_out (sw_171_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_171 (
        .io_in  (sw_171_module_data_in),
        .io_out (sw_171_module_data_out)
    );

    // [172] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_172_clk_out, sw_172_data_out, sw_172_scan_out, sw_172_latch_out;
    wire [7:0] sw_172_module_data_in;
    wire [7:0] sw_172_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_172 (
        .clk_in          (sw_171_clk_out),
        .data_in         (sw_171_data_out),
        .scan_select_in  (sw_171_scan_out),
        .latch_enable_in (sw_171_latch_out),
        .clk_out         (sw_172_clk_out),
        .data_out        (sw_172_data_out),
        .scan_select_out (sw_172_scan_out),
        .latch_enable_out(sw_172_latch_out),
        .module_data_in  (sw_172_module_data_in),
        .module_data_out (sw_172_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_172 (
        .io_in  (sw_172_module_data_in),
        .io_out (sw_172_module_data_out)
    );

    // [173] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_173_clk_out, sw_173_data_out, sw_173_scan_out, sw_173_latch_out;
    wire [7:0] sw_173_module_data_in;
    wire [7:0] sw_173_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_173 (
        .clk_in          (sw_172_clk_out),
        .data_in         (sw_172_data_out),
        .scan_select_in  (sw_172_scan_out),
        .latch_enable_in (sw_172_latch_out),
        .clk_out         (sw_173_clk_out),
        .data_out        (sw_173_data_out),
        .scan_select_out (sw_173_scan_out),
        .latch_enable_out(sw_173_latch_out),
        .module_data_in  (sw_173_module_data_in),
        .module_data_out (sw_173_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_173 (
        .io_in  (sw_173_module_data_in),
        .io_out (sw_173_module_data_out)
    );

    // [174] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_174_clk_out, sw_174_data_out, sw_174_scan_out, sw_174_latch_out;
    wire [7:0] sw_174_module_data_in;
    wire [7:0] sw_174_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_174 (
        .clk_in          (sw_173_clk_out),
        .data_in         (sw_173_data_out),
        .scan_select_in  (sw_173_scan_out),
        .latch_enable_in (sw_173_latch_out),
        .clk_out         (sw_174_clk_out),
        .data_out        (sw_174_data_out),
        .scan_select_out (sw_174_scan_out),
        .latch_enable_out(sw_174_latch_out),
        .module_data_in  (sw_174_module_data_in),
        .module_data_out (sw_174_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_174 (
        .io_in  (sw_174_module_data_in),
        .io_out (sw_174_module_data_out)
    );

    // [175] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_175_clk_out, sw_175_data_out, sw_175_scan_out, sw_175_latch_out;
    wire [7:0] sw_175_module_data_in;
    wire [7:0] sw_175_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_175 (
        .clk_in          (sw_174_clk_out),
        .data_in         (sw_174_data_out),
        .scan_select_in  (sw_174_scan_out),
        .latch_enable_in (sw_174_latch_out),
        .clk_out         (sw_175_clk_out),
        .data_out        (sw_175_data_out),
        .scan_select_out (sw_175_scan_out),
        .latch_enable_out(sw_175_latch_out),
        .module_data_in  (sw_175_module_data_in),
        .module_data_out (sw_175_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_175 (
        .io_in  (sw_175_module_data_in),
        .io_out (sw_175_module_data_out)
    );

    // [176] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_176_clk_out, sw_176_data_out, sw_176_scan_out, sw_176_latch_out;
    wire [7:0] sw_176_module_data_in;
    wire [7:0] sw_176_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_176 (
        .clk_in          (sw_175_clk_out),
        .data_in         (sw_175_data_out),
        .scan_select_in  (sw_175_scan_out),
        .latch_enable_in (sw_175_latch_out),
        .clk_out         (sw_176_clk_out),
        .data_out        (sw_176_data_out),
        .scan_select_out (sw_176_scan_out),
        .latch_enable_out(sw_176_latch_out),
        .module_data_in  (sw_176_module_data_in),
        .module_data_out (sw_176_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_176 (
        .io_in  (sw_176_module_data_in),
        .io_out (sw_176_module_data_out)
    );

    // [177] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_177_clk_out, sw_177_data_out, sw_177_scan_out, sw_177_latch_out;
    wire [7:0] sw_177_module_data_in;
    wire [7:0] sw_177_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_177 (
        .clk_in          (sw_176_clk_out),
        .data_in         (sw_176_data_out),
        .scan_select_in  (sw_176_scan_out),
        .latch_enable_in (sw_176_latch_out),
        .clk_out         (sw_177_clk_out),
        .data_out        (sw_177_data_out),
        .scan_select_out (sw_177_scan_out),
        .latch_enable_out(sw_177_latch_out),
        .module_data_in  (sw_177_module_data_in),
        .module_data_out (sw_177_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_177 (
        .io_in  (sw_177_module_data_in),
        .io_out (sw_177_module_data_out)
    );

    // [178] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_178_clk_out, sw_178_data_out, sw_178_scan_out, sw_178_latch_out;
    wire [7:0] sw_178_module_data_in;
    wire [7:0] sw_178_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_178 (
        .clk_in          (sw_177_clk_out),
        .data_in         (sw_177_data_out),
        .scan_select_in  (sw_177_scan_out),
        .latch_enable_in (sw_177_latch_out),
        .clk_out         (sw_178_clk_out),
        .data_out        (sw_178_data_out),
        .scan_select_out (sw_178_scan_out),
        .latch_enable_out(sw_178_latch_out),
        .module_data_in  (sw_178_module_data_in),
        .module_data_out (sw_178_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_178 (
        .io_in  (sw_178_module_data_in),
        .io_out (sw_178_module_data_out)
    );

    // [179] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_179_clk_out, sw_179_data_out, sw_179_scan_out, sw_179_latch_out;
    wire [7:0] sw_179_module_data_in;
    wire [7:0] sw_179_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_179 (
        .clk_in          (sw_178_clk_out),
        .data_in         (sw_178_data_out),
        .scan_select_in  (sw_178_scan_out),
        .latch_enable_in (sw_178_latch_out),
        .clk_out         (sw_179_clk_out),
        .data_out        (sw_179_data_out),
        .scan_select_out (sw_179_scan_out),
        .latch_enable_out(sw_179_latch_out),
        .module_data_in  (sw_179_module_data_in),
        .module_data_out (sw_179_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_179 (
        .io_in  (sw_179_module_data_in),
        .io_out (sw_179_module_data_out)
    );

    // [180] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_180_clk_out, sw_180_data_out, sw_180_scan_out, sw_180_latch_out;
    wire [7:0] sw_180_module_data_in;
    wire [7:0] sw_180_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_180 (
        .clk_in          (sw_179_clk_out),
        .data_in         (sw_179_data_out),
        .scan_select_in  (sw_179_scan_out),
        .latch_enable_in (sw_179_latch_out),
        .clk_out         (sw_180_clk_out),
        .data_out        (sw_180_data_out),
        .scan_select_out (sw_180_scan_out),
        .latch_enable_out(sw_180_latch_out),
        .module_data_in  (sw_180_module_data_in),
        .module_data_out (sw_180_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_180 (
        .io_in  (sw_180_module_data_in),
        .io_out (sw_180_module_data_out)
    );

    // [181] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_181_clk_out, sw_181_data_out, sw_181_scan_out, sw_181_latch_out;
    wire [7:0] sw_181_module_data_in;
    wire [7:0] sw_181_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_181 (
        .clk_in          (sw_180_clk_out),
        .data_in         (sw_180_data_out),
        .scan_select_in  (sw_180_scan_out),
        .latch_enable_in (sw_180_latch_out),
        .clk_out         (sw_181_clk_out),
        .data_out        (sw_181_data_out),
        .scan_select_out (sw_181_scan_out),
        .latch_enable_out(sw_181_latch_out),
        .module_data_in  (sw_181_module_data_in),
        .module_data_out (sw_181_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_181 (
        .io_in  (sw_181_module_data_in),
        .io_out (sw_181_module_data_out)
    );

    // [182] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_182_clk_out, sw_182_data_out, sw_182_scan_out, sw_182_latch_out;
    wire [7:0] sw_182_module_data_in;
    wire [7:0] sw_182_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_182 (
        .clk_in          (sw_181_clk_out),
        .data_in         (sw_181_data_out),
        .scan_select_in  (sw_181_scan_out),
        .latch_enable_in (sw_181_latch_out),
        .clk_out         (sw_182_clk_out),
        .data_out        (sw_182_data_out),
        .scan_select_out (sw_182_scan_out),
        .latch_enable_out(sw_182_latch_out),
        .module_data_in  (sw_182_module_data_in),
        .module_data_out (sw_182_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_182 (
        .io_in  (sw_182_module_data_in),
        .io_out (sw_182_module_data_out)
    );

    // [183] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_183_clk_out, sw_183_data_out, sw_183_scan_out, sw_183_latch_out;
    wire [7:0] sw_183_module_data_in;
    wire [7:0] sw_183_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_183 (
        .clk_in          (sw_182_clk_out),
        .data_in         (sw_182_data_out),
        .scan_select_in  (sw_182_scan_out),
        .latch_enable_in (sw_182_latch_out),
        .clk_out         (sw_183_clk_out),
        .data_out        (sw_183_data_out),
        .scan_select_out (sw_183_scan_out),
        .latch_enable_out(sw_183_latch_out),
        .module_data_in  (sw_183_module_data_in),
        .module_data_out (sw_183_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_183 (
        .io_in  (sw_183_module_data_in),
        .io_out (sw_183_module_data_out)
    );

    // [184] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_184_clk_out, sw_184_data_out, sw_184_scan_out, sw_184_latch_out;
    wire [7:0] sw_184_module_data_in;
    wire [7:0] sw_184_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_184 (
        .clk_in          (sw_183_clk_out),
        .data_in         (sw_183_data_out),
        .scan_select_in  (sw_183_scan_out),
        .latch_enable_in (sw_183_latch_out),
        .clk_out         (sw_184_clk_out),
        .data_out        (sw_184_data_out),
        .scan_select_out (sw_184_scan_out),
        .latch_enable_out(sw_184_latch_out),
        .module_data_in  (sw_184_module_data_in),
        .module_data_out (sw_184_module_data_out)
    );

    user_module_341535056611770964 user_module_341535056611770964_184 (
        .io_in  (sw_184_module_data_in),
        .io_out (sw_184_module_data_out)
    );

    // [185] https://github.com/TinyTapeout/tt02-test-invert
    wire sw_185_clk_out, sw_185_data_out, sw_185_scan_out, sw_185_latch_out;
    wire [7:0] sw_185_module_data_in;
    wire [7:0] sw_185_module_data_out;
    scanchain #(.NUM_IOS(8)) scanchain_185 (
        .clk_in          (sw_184_clk_out),
        .data_in         (sw_184_data_out),