| // SPDX-FileCopyrightText: 2020 Efabless Corporation |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| |
| `default_nettype none |
| /* |
| *------------------------------------------------------------- |
| * |
| * btc_miner_top |
| * TODO! |
| * |
| * This is an example of a (trivially simple) user project, |
| * showing how the user project can connect to the logic |
| * analyzer, the wishbone bus, and the I/O pads. |
| * |
| * This project generates an integer count, which is output |
| * on the user area GPIO pads (digital output only). The |
| * wishbone connection allows the project to be controlled |
| * (start and stop) from the management SoC program. |
| * |
| * See the testbenches in directory "mprj_counter" for the |
| * example programs that drive this user project. The three |
| * testbenches are "io_ports", "la_test1", and "la_test2". |
| * |
| *------------------------------------------------------------- |
| */ |
| |
| module btc_miner_top #( |
| parameter BITS = 32 |
| )( |
| `ifdef USE_POWER_PINS |
| inout vccd1, // User area 1 1.8V supply |
| inout vssd1, // User area 1 digital ground |
| `endif |
| |
| // Wishbone Slave ports (WB MI A) |
| input wb_clk_i, |
| input wb_rst_i, |
| input wbs_stb_i, |
| input wbs_cyc_i, |
| input wbs_we_i, |
| input [3:0] wbs_sel_i, |
| input [31:0] wbs_dat_i, |
| input [31:0] wbs_adr_i, |
| output wbs_ack_o, |
| output [31:0] wbs_dat_o, |
| |
| // Logic Analyzer Signals |
| input [127:0] la_data_in, |
| output [127:0] la_data_out, |
| input [127:0] la_oenb, |
| |
| // IOs |
| input [`MPRJ_IO_PADS-1:0] io_in, |
| output [`MPRJ_IO_PADS-1:0] io_out, |
| output [`MPRJ_IO_PADS-1:0] io_oeb, |
| |
| // IRQ |
| output [2:0] irq |
| ); |
| wire clk; |
| wire rst; |
| |
| wire [`MPRJ_IO_PADS-1:0] io_in; |
| wire [`MPRJ_IO_PADS-1:0] io_out; |
| wire [`MPRJ_IO_PADS-1:0] io_oeb; |
| |
| // WB wires |
| wire [31:0] rdata; |
| wire [31:0] wdata; |
| |
| wire valid; |
| wire [3:0] wstrb; |
| |
| // LA wires |
| wire [31:0] la_write0; |
| wire [31:0] la_write1; |
| wire [31:0] la_write2; |
| wire [31:0] la_write3; |
| |
| // SHA module variables |
| wire o_error; |
| wire o_idle; |
| wire o_sha_cs; |
| wire o_sha_we; |
| wire [7:0] o_sha_address; |
| |
| reg [127:0] la_data_out; // TODO? ensure LA muxing does not require register |
| |
| // TODO use top 32-bits of LA to control muxing and other variables like starting state machine |
| wire [5:0] la_sel; |
| assign la_sel = la_data_in[127:122]; |
| |
| // WB MI A |
| assign valid = wbs_cyc_i && wbs_stb_i; |
| assign wstrb = wbs_sel_i & {4{wbs_we_i}}; |
| assign wbs_dat_o = rdata; |
| assign wdata = wbs_dat_i; |
| |
| // IO |
| assign io_out = rdata; |
| assign io_oeb = {(`MPRJ_IO_PADS-1){rst}}; |
| |
| // IRQ |
| assign irq = 3'b000; // Unused |
| |
| // Assuming LA probes [31:0] (aka: la_write0) are for controlling the nonce register. |
| // * NOTE: These are used as a mask for the la_data_in[?:?] |
| assign la_write0 = ~la_oenb[31:0] & ~{BITS{valid}}; |
| assign la_write1 = ~la_oenb[63:32] & ~{BITS{valid}}; |
| assign la_write2 = ~la_oenb[95:64] & ~{BITS{valid}}; |
| assign la_write3 = ~la_oenb[127:96] & ~{BITS{valid}}; |
| |
| // Assuming LA probes [111:110] are for controlling the reset & clock |
| assign clk = (~la_oenb[110]) ? la_data_in[110] : wb_clk_i; |
| assign rst = (~la_oenb[111]) ? la_data_in[111] : wb_rst_i; |
| |
| // TODO more LA muxing |
| // la_data_in or la_data_out or la_oenb or la_sel or nonce or block_header or target |
| always @(la_data_in || la_oenb || la_sel || rdata || o_error || o_idle) begin |
| case (la_sel) |
| 6'b000000: |
| la_data_out <= {{(127-(BITS-12)){1'b0}}, {o_idle, o_error, o_sha_we, o_sha_cs, o_sha_address, rdata}}; |
| |
| default: |
| begin |
| la_data_out <= {{(127-(BITS-12)){1'b0}}, {o_idle, o_error, o_sha_we, o_sha_cs, o_sha_address, rdata}}; |
| end |
| endcase |
| end |
| |
| // TODO create state machine for reading block header and passing to miner |
| miner_ctrl #( |
| .BITS(BITS) |
| ) miner_ctrl( |
| .clk(clk), |
| .rst(rst), |
| .valid(valid), |
| .wb_wr_mask(wstrb), |
| .wdata(wbs_dat_i), |
| .la_write3(la_write3), |
| .la_input3(la_data_in[127:96]), |
| .rdata(rdata), |
| .ready(wbs_ack_o), |
| .error(o_error), |
| .idle(o_idle), |
| .reg_sha_cs(o_sha_cs), |
| .reg_sha_we(o_sha_we), |
| .reg_sha_address(o_sha_address) |
| ); |
| |
| endmodule // btc_miner_top |
| |
| |
| // miner_ctrl |
| module miner_ctrl #( |
| parameter BITS = 32 |
| )( |
| input wire clk, |
| input wire rst, |
| input wire valid, |
| input wire [3:0] wb_wr_mask, |
| input wire [BITS-1:0] wdata, |
| input wire [BITS-1:0] la_write3, |
| input wire [BITS-1:0] la_input3, |
| output reg [BITS-1:0] rdata, |
| output reg ready, |
| output wire error, |
| output wire idle, |
| output reg reg_sha_cs, |
| output reg reg_sha_we, |
| output reg [7:0] reg_sha_address |
| ); |
| |
| // sha256 internal constants and parameters |
| localparam ADDR_NAME0 = 8'h00; |
| localparam ADDR_NAME1 = 8'h01; |
| localparam ADDR_VERSION = 8'h02; |
| |
| localparam ADDR_CTRL = 8'h08; |
| localparam CTRL_INIT_BIT = 0; |
| localparam CTRL_NEXT_BIT = 1; |
| localparam CTRL_MODE_BIT = 2; |
| |
| localparam ADDR_STATUS = 8'h09; |
| localparam STATUS_READY_BIT = 0; |
| localparam STATUS_VALID_BIT = 1; |
| |
| localparam ADDR_BLOCK0 = 8'h10; |
| // localparam ADDR_BLOCK1 = 8'h11; |
| // localparam ADDR_BLOCK2 = 8'h12; |
| // localparam ADDR_BLOCK3 = 8'h13; |
| // localparam ADDR_BLOCK4 = 8'h14; |
| // localparam ADDR_BLOCK5 = 8'h15; |
| // localparam ADDR_BLOCK6 = 8'h16; |
| // localparam ADDR_BLOCK7 = 8'h17; |
| // localparam ADDR_BLOCK8 = 8'h18; |
| // localparam ADDR_BLOCK9 = 8'h19; |
| // localparam ADDR_BLOCK10 = 8'h1a; |
| // localparam ADDR_BLOCK11 = 8'h1b; |
| // localparam ADDR_BLOCK12 = 8'h1c; |
| // localparam ADDR_BLOCK13 = 8'h1d; |
| // localparam ADDR_BLOCK14 = 8'h1e; |
| localparam ADDR_BLOCK15 = 8'h1f; |
| |
| localparam ADDR_DIGEST0 = 8'h20; |
| // localparam ADDR_DIGEST1 = 8'h21; |
| // localparam ADDR_DIGEST2 = 8'h22; |
| // localparam ADDR_DIGEST3 = 8'h23; |
| // localparam ADDR_DIGEST4 = 8'h24; |
| // localparam ADDR_DIGEST5 = 8'h25; |
| // localparam ADDR_DIGEST6 = 8'h26; |
| localparam ADDR_DIGEST7 = 8'h27; |
| |
| localparam MODE_SHA_224 = 1'h0; |
| localparam MODE_SHA_256 = 1'h1; |
| |
| // enum logic [1:0] {WAIT_IN=2'b00, READ_IN=2'b01, WAIT_COMPUTE=2'b10, CHECK=2'b11, WRITE_OUT=} state; |
| // enum integer unsigned {WAIT_IN=0, READ_IN=1, WAIT_COMPUTE=2, INCR_NONCE=3, WRITE_OUT=4} state; |
| localparam WAIT_IN=0, READ_IN=1, WAIT_COMPUTE=2, WRITE_OUT=3; |
| |
| reg [2:0] state; |
| |
| wire start_ctrl; |
| wire sha_cs; |
| wire sha_we; |
| wire [7:0] sha_address; |
| wire read_status_flag; |
| |
| wire [BITS-1:0] sha_write_data; // input to sha256 |
| wire [BITS-1:0] sha_read_data; // output from sha256 |
| |
| wire sha_in_ready; |
| wire sha_digest_valid; |
| wire auto_ctrl; |
| |
| assign idle = (state == WAIT_IN) ? 1'b1 : 1'b0; |
| assign start_ctrl = la_input3[10] & la_write3[10]; |
| |
| // automated and manual control |
| assign read_status_flag = sha_cs && !sha_we && (sha_address == ADDR_STATUS); |
| assign sha_in_ready = read_status_flag ? sha_read_data[STATUS_READY_BIT] : 1'b0; |
| assign sha_digest_valid = read_status_flag ? sha_read_data[STATUS_VALID_BIT] : 1'b0; |
| |
| assign auto_ctrl = la_input3[11] & la_write3[11]; |
| |
| assign sha_cs = auto_ctrl ? reg_sha_cs : (la_input3[8] & la_write3[8]); |
| assign sha_we = auto_ctrl ? reg_sha_we : (la_input3[9] & la_write3[9]); |
| assign sha_address = auto_ctrl ? reg_sha_address : (la_input3[7:0] & la_write3[7:0]); |
| |
| // need to count to 640/32 = 20 (decimal). Only to 19 b/c nonce is last 32-bits |
| integer unsigned count; |
| |
| always @(posedge clk) begin |
| if (rst) begin |
| ready <= 0; |
| rdata <= 0; |
| count <= 0; |
| reg_sha_cs <= 0; |
| reg_sha_we <= 0; |
| reg_sha_address <= 0; |
| // sha_in_ready <= 0; |
| // sha_digest_valid <= 0; |
| |
| state <= WAIT_IN; |
| end else if (auto_ctrl) begin |
| ready <= 1'b0; |
| |
| // state machine for controlling miner and I/O |
| case (state) |
| WAIT_IN: begin |
| // TODO? |
| reg_sha_cs <= 1'b1; |
| reg_sha_we <= 1'b0; |
| reg_sha_address <= ADDR_STATUS; |
| |
| if (start_ctrl && sha_in_ready) begin |
| reg_sha_cs <= 1'b1; |
| reg_sha_we <= 1'b1; |
| state <= READ_IN; |
| end |
| end |
| |
| READ_IN: begin |
| // TODO? |
| reg_sha_cs <= 1'b1; |
| reg_sha_we <= 1'b1; |
| |
| if (valid && !ready) begin |
| ready <= 1'b1; |
| sha_write_data <= wdata; |
| |
| if (wb_wr_mask == 4'b1111) begin |
| // read up to the last address |
| if (reg_sha_address == ADDR_BLOCK15) begin |
| state <= WAIT_COMPUTE; |
| end else begin |
| // check if 1st write coming from WAIT_IN |
| if (sha_address == ADDR_STATUS) begin |
| reg_sha_address <= ADDR_BLOCK0; |
| end else begin |
| reg_sha_address <= reg_sha_address + 1; |
| end |
| end |
| |
| end |
| end |
| end |
| |
| WAIT_COMPUTE: begin |
| // read status register to determine when done |
| reg_sha_cs <= 1'b1; |
| reg_sha_we <= 1'b0; |
| reg_sha_address <= ADDR_STATUS; |
| |
| if (sha_digest_valid) begin |
| reg_sha_address <= ADDR_DIGEST0; |
| state <= WRITE_OUT; |
| end |
| end |
| |
| WRITE_OUT: begin |
| // TODO? |
| reg_sha_cs <= 1'b1; |
| reg_sha_we <= 1'b0; |
| |
| if (valid && !ready) begin |
| ready <= 1'b1; |
| |
| // Place output hash on wishbone |
| if (wb_wr_mask == 4'b0000) begin |
| rdata <= sha_read_data; |
| |
| if (reg_sha_address == ADDR_DIGEST7) begin |
| state <= WAIT_IN; |
| end else begin |
| reg_sha_address <= reg_sha_address + 1; |
| end |
| end |
| end |
| end |
| |
| endcase |
| end else begin |
| // TODO not automated control. FW controls all wr/rd and addresses. |
| end |
| |
| // set ready and valid bits for sha256 module |
| // if (sha_cs && !sha_we && (sha_address == ADDR_STATUS)) begin |
| // sha_in_ready <= sha_read_data[STATUS_READY_BIT]; |
| // sha_digest_valid <= sha_read_data[STATUS_VALID_BIT]; |
| // end else begin |
| // sha_in_ready <= 1'b0; |
| // sha_digest_valid <= 1'b0; |
| // end |
| end |
| |
| // TODO handle ADDR_CTRL register! |
| sha256 sha256_inst0( |
| .clk(clk), |
| .reset_n(~rst), |
| .cs(sha_cs), |
| .we(sha_we), |
| .address(sha_address), |
| .write_data(sha_write_data), // 32-bit input |
| .read_data(sha_read_data), // 32-bit output |
| .error(error) // 1-bit output |
| ); |
| |
| endmodule // miner_ctrl |
| |
| `default_nettype wire |
