| `default_nettype none |
| /* |
| * Copyright (C) 2017 Clifford Wolf <clifford@clifford.at> |
| * Copyright (C) 2018 Tim Edwards <tim@efabless.com> |
| * Copyright (C) 2020 Anton Blanchard <anton@linux.ibm.com> |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| * |
| */ |
| |
| `timescale 1 ns / 1 ps |
| |
| module multiply_test; |
| reg clock; |
| reg RSTB; |
| reg microwatt_reset; |
| reg power1, power2; |
| reg power3, power4; |
| |
| wire gpio; |
| wire [37:0] mprj_io; |
| wire [15:0] checkbits; |
| wire user_flash_csb; |
| wire user_flash_clk; |
| inout user_flash_io0; |
| inout user_flash_io1; |
| wire uart_tx; |
| |
| assign mprj_io[7] = microwatt_reset; |
| |
| assign mprj_io[35] = 1'b1; // Boot from flash |
| // |
| assign user_flash_csb = mprj_io[8]; |
| assign user_flash_clk = mprj_io[9]; |
| assign user_flash_io0 = mprj_io[10]; |
| assign mprj_io[11] = user_flash_io1; |
| |
| assign checkbits = mprj_io[31:16]; |
| |
| assign uart_tx = mprj_io[6]; |
| assign mprj_io[5] = 1'b1; |
| |
| assign mprj_io[3] = 1'b1; // Force CSB high. |
| |
| // 100 MHz clock |
| always #5 clock <= (clock === 1'b0); |
| |
| initial begin |
| clock = 0; |
| end |
| |
| initial begin |
| //$dumpfile("multiply_test.vcd"); |
| //$dumpvars(0, multiply_test); |
| |
| $display("Microwatt multiply test"); |
| |
| repeat (500000) @(posedge clock); |
| $display("Timeout"); |
| $finish; |
| end |
| |
| initial begin |
| RSTB <= 1'b0; |
| microwatt_reset <= 1'b1; |
| #1000; |
| microwatt_reset <= 1'b0; |
| // Note: keep management engine in reset |
| //RSTB <= 1'b1; |
| end |
| |
| initial begin // Power-up sequence |
| power1 <= 1'b0; |
| power2 <= 1'b0; |
| power3 <= 1'b0; |
| power4 <= 1'b0; |
| #100; |
| power1 <= 1'b1; |
| #100; |
| power2 <= 1'b1; |
| #100; |
| power3 <= 1'b1; |
| #100; |
| power4 <= 1'b1; |
| end |
| |
| always @(checkbits) begin |
| wait(checkbits == 16'h0ffe) |
| $display("Microwatt alive!"); |
| |
| wait(checkbits != 16'h0ffe); |
| |
| if(checkbits == 16'h7345) begin |
| $display("Fail"); |
| $finish; |
| end |
| |
| if(checkbits == 16'h00d5) begin |
| $display("Success"); |
| $finish; |
| end |
| |
| $display("Unknown Failure %x", checkbits); |
| $finish; |
| end |
| |
| wire VDD3V3 = power1; |
| wire VDD1V8 = power2; |
| wire USER_VDD3V3 = power3; |
| wire USER_VDD1V8 = power4; |
| wire VSS = 1'b0; |
| |
| caravel uut ( |
| .vddio (VDD3V3), |
| .vssio (VSS), |
| .vdda (VDD3V3), |
| .vssa (VSS), |
| .vccd (VDD1V8), |
| .vssd (VSS), |
| .vdda1 (USER_VDD3V3), |
| .vdda2 (USER_VDD3V3), |
| .vssa1 (VSS), |
| .vssa2 (VSS), |
| .vccd1 (USER_VDD1V8), |
| .vccd2 (USER_VDD1V8), |
| .vssd1 (VSS), |
| .vssd2 (VSS), |
| .clock (clock), |
| .gpio (gpio), |
| .mprj_io (mprj_io), |
| .resetb (RSTB) |
| ); |
| |
| spiflash_microwatt #( |
| .FILENAME("microwatt.hex") |
| ) spiflash_microwatt ( |
| .csb(user_flash_csb), |
| .clk(user_flash_clk), |
| .io0(user_flash_io0), |
| .io1(user_flash_io1), |
| .io2(), // not used |
| .io3() // not used |
| ); |
| |
| tbuart_microwatt #( |
| .baud_rate(115200) |
| ) tbuart ( |
| .ser_rx(uart_tx) |
| ); |
| |
| endmodule |
| `default_nettype wire |