digital pll integration
diff --git a/verilog/dv/user_i2cm/Makefile b/verilog/dv/user_i2cm/Makefile
index a801f55..f01c09d 100644
--- a/verilog/dv/user_i2cm/Makefile
+++ b/verilog/dv/user_i2cm/Makefile
@@ -24,8 +24,12 @@
#######################################################################
DESIGNS?=../../..
+TOOLS?=/opt/riscv64i/
export USER_PROJECT_VERILOG ?= $(DESIGNS)/verilog
+## YIFIVE FIRMWARE
+YIFIVE_FIRMWARE_PATH = $(USER_PROJECT_VERILOG)/dv/firmware
+GCC64_PREFIX?=riscv64-unknown-elf
## Simulation mode: RTL/GL
@@ -50,20 +54,24 @@
ifeq ($(DUMP),OFF)
iverilog -g2012 -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib \
$< -o $@
else
iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib \
$< -o $@
endif
else
ifeq ($(DUMP),OFF)
iverilog -g2012 -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
-f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
$< -o $@
else
iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
-f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+ -f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
$< -o $@
endif
endif
diff --git a/verilog/dv/user_i2cm/user_i2cm_tb.v b/verilog/dv/user_i2cm/user_i2cm_tb.v
index 0607308..e0f8219 100644
--- a/verilog/dv/user_i2cm/user_i2cm_tb.v
+++ b/verilog/dv/user_i2cm/user_i2cm_tb.v
@@ -444,13 +444,11 @@
wbd_ext_we_i ='h0; // write
wbd_ext_dat_i ='h0; // data output
wbd_ext_sel_i ='h0; // byte enable
- if(data === cmp_data) begin
- $display("STATUS: DEBUG WB USER ACCESS READ Address : %x, Data : %x",address,data);
+ if(data !== cmp_data) begin
+ $display("ERROR : WB USER ACCESS READ Address : 0x%x, Exd: 0x%x Rxd: 0x%x ",address,cmp_data,data);
+ test_fail = 1;
end else begin
- $display("ERROR: DEBUG WB USER ACCESS READ Address : %x, Exp Data : %x Rxd Data: ",address,cmp_data,data);
- test_fail= 1;
- #100
- $finish;
+ $display("STATUS: WB USER ACCESS READ Address : 0x%x, Data : 0x%x",address,data);
end
repeat (2) @(posedge clock);
end
@@ -458,29 +456,21 @@
`ifdef GL
-wire wbd_spi_stb_i = u_top.u_spi_master.wbd_stb_i;
-wire wbd_spi_ack_o = u_top.u_spi_master.wbd_ack_o;
-wire wbd_spi_we_i = u_top.u_spi_master.wbd_we_i;
-wire [31:0] wbd_spi_adr_i = u_top.u_spi_master.wbd_adr_i;
-wire [31:0] wbd_spi_dat_i = u_top.u_spi_master.wbd_dat_i;
-wire [31:0] wbd_spi_dat_o = u_top.u_spi_master.wbd_dat_o;
-wire [3:0] wbd_spi_sel_i = u_top.u_spi_master.wbd_sel_i;
+wire wbd_spi_stb_i = u_top.u_qspi_master.wbd_stb_i;
+wire wbd_spi_ack_o = u_top.u_qspi_master.wbd_ack_o;
+wire wbd_spi_we_i = u_top.u_qspi_master.wbd_we_i;
+wire [31:0] wbd_spi_adr_i = u_top.u_qspi_master.wbd_adr_i;
+wire [31:0] wbd_spi_dat_i = u_top.u_qspi_master.wbd_dat_i;
+wire [31:0] wbd_spi_dat_o = u_top.u_qspi_master.wbd_dat_o;
+wire [3:0] wbd_spi_sel_i = u_top.u_qspi_master.wbd_sel_i;
-wire wbd_sdram_stb_i = u_top.u_sdram_ctrl.wb_stb_i;
-wire wbd_sdram_ack_o = u_top.u_sdram_ctrl.wb_ack_o;
-wire wbd_sdram_we_i = u_top.u_sdram_ctrl.wb_we_i;
-wire [31:0] wbd_sdram_adr_i = u_top.u_sdram_ctrl.wb_addr_i;
-wire [31:0] wbd_sdram_dat_i = u_top.u_sdram_ctrl.wb_dat_i;
-wire [31:0] wbd_sdram_dat_o = u_top.u_sdram_ctrl.wb_dat_o;
-wire [3:0] wbd_sdram_sel_i = u_top.u_sdram_ctrl.wb_sel_i;
-
-wire wbd_uart_stb_i = u_top.u_uart_i2c.u_uart_core.reg_cs;
-wire wbd_uart_ack_o = u_top.u_uart_i2c.u_uart_core.reg_ack;
-wire wbd_uart_we_i = u_top.u_uart_i2c.u_uart_core.reg_wr;
-wire [7:0] wbd_uart_adr_i = u_top.u_uart_i2c.u_uart_core.reg_addr;
-wire [7:0] wbd_uart_dat_i = u_top.u_uart_i2c.u_uart_core.reg_wdata;
-wire [7:0] wbd_uart_dat_o = u_top.u_uart_i2c.u_uart_core.reg_rdata;
-wire wbd_uart_sel_i = u_top.u_uart_i2c.u_uart_core.reg_be;
+wire wbd_uart_stb_i = u_top.u_uart_i2c_usb_spi.reg_cs;
+wire wbd_uart_ack_o = u_top.u_uart_i2c_usb_spi.reg_ack;
+wire wbd_uart_we_i = u_top.u_uart_i2c_usb_spi.reg_wr;
+wire [8:0] wbd_uart_adr_i = u_top.u_uart_i2c_usb_spi.reg_addr;
+wire [7:0] wbd_uart_dat_i = u_top.u_uart_i2c_usb_spi.reg_wdata;
+wire [7:0] wbd_uart_dat_o = u_top.u_uart_i2c_usb_spi.reg_rdata;
+wire wbd_uart_sel_i = u_top.u_uart_i2c_usb_spi.reg_be;
`endif
