| # Makefile for efabless design kits for SkyWater Sky130: |
| # |
| # sky130A = 5-metal backend stack with dual MiM |
| # |
| # Written by Tim Edwards March 2019 |
| # efabless corporation |
| # updated October 2019 |
| # updated December 2019 (divide installation sections for individual tools) |
| # updated March 2020 (refactored the install process) |
| # updated May 2020 (changed to new process name Sky130) |
| # |
| # Instructions: |
| # |
| # Run "configure" from the top level directory. Use the following |
| # configuration options to match your environment: |
| # |
| # --enable-sky130-pdk[=<path>] |
| # If enabled, install the skywater PDK. If <path> is specified, |
| # then the skywater PDK is expected to be found rooted at the |
| # given path. If not specified, then the skywater PDK will be |
| # downloaded and installed to <repo root>/pdks. |
| # If explicitly disabled, sky130 is skipped over entirely. |
| # |
| # --with-sky130-link-targets=<value> |
| # where <value> is one of "none" or "source". If set to "source", |
| # then where possible, the installed files are symbolic links |
| # back to the source, rather than copies of the source. The |
| # default value is "none" if the option is not specified. |
| # |
| # --with-ef-style |
| # If specified, then the installation uses the efabless style, |
| # which swaps the file hierarchy of file formats vs. IP libraries; |
| # e.g., "gds/sky130_fd_sc_hd/" with ef-style, vs. |
| # "sky130_fd_sc_hd/gds/" without it. |
| # |
| # Enable/disable for specific libraries to be installed (and downloaded if |
| # needed). Libraries that are part of the open_pdks repository are enabled |
| # by default and must be disabled by passing an option to configure. Libraries |
| # that are not part of the open_pdks repository are disabled by default and |
| # must be enabled by passing an option to configure. |
| # |
| # Internal libraries and tool setups that can be disabled are the following: |
| # |
| # --disable-magic |
| # Do not install setup files for the magic layout tool. |
| # |
| # --disable-netgen |
| # Do not install setup files for the netgen LVS tool. |
| # |
| # --disable-irsim |
| # Do not install setup files for the IRSIM simulation tool. |
| # |
| # --disable-qflow |
| # Do not install setup files for the qflow synthesis flow. |
| # |
| # --disable-openlane |
| # Do not install setup files for the openlane sythesis flow. |
| # |
| # --disable-klayout |
| # Do not install setup files for the klayout layout tool. |
| # |
| # |
| # NOTE: The comments below are for features that have not yet been |
| # implemented. |
| # |
| # External (third-party) libraries and tool setups are the following (enabled |
| # by default): |
| # |
| # --enable-alpha-sky130[=<path>] |
| # If enabled, install the sky130_ml_xx_hd font library from |
| # Paul Schulz on github. If <path> is not specified, then the |
| # font library will be cloned from the git repository and |
| # installed. |
| # |
| # --enable-xschem-sky130[=<path>] |
| # If enabled, install the Sky130 setup for the xschem schematic |
| # editor. If <path> is specified, then the xschem setup is |
| # expected to be found rooted at the given path. If not |
| # specified, then the xschem setup will be cloned from the |
| # repository and installed. |
| # |
| # External (third-party) libraries and tool setups are the following (disabled |
| # by default): |
| # |
| # --enable-sram-sky130[=<path>] |
| # If enabled, install the sky130_sram_macros library from |
| # efabless on github. If <path> is not specified, then |
| # the SRAM library will be cloned from the repository and |
| # installed. |
| # |
| # --enable-osu-sky130[=<path>] |
| # If enabled, install the sky130_osu_sc library from |
| # foss-eda-tools on googlesource. If <path> is not |
| # specified, then the OSU standard cell library will be |
| # clones from the repository and installed. |
| # |
| # --enable-osu-t12-sky130[=<path>] |
| # If enabled, install the sky130_osu_sc_t12 libraries from |
| # foss-eda-tools on googlesource. If <path> is not |
| # specified, then the OSU standard cell library will be |
| # clones from the repository and installed. |
| # |
| # --enable-osu-t15-sky130[=<path>] |
| # If enabled, install the sky130_osu_sc_t15 libraries from |
| # foss-eda-tools on googlesource. If <path> is not |
| # specified, then the OSU standard cell library will be |
| # clones from the repository and installed. |
| # |
| # --enable-osu-t18-sky130[=<path>] |
| # If enabled, install the sky130_osu_sc_t18 libraries from |
| # foss-eda-tools on googlesource. If <path> is not |
| # specified, then the OSU standard cell library will be |
| # clones from the repository and installed. |
| # |
| # The variables below are substituted from the configuration options: |
| # |
| # SKYWATER_PATH: points to vendor sources |
| # EF_STYLE: 1 for efabless style, 0 otherwise |
| # LINK_TARGETS: link back to source or link to 1st PDK when possible |
| # |
| # Run "make" to stage the PDK for tool setup and vendor libraries |
| # |
| # Run "make install" to install all staged files. |
| # |
| # Run "make clean" to remove all staging files. |
| # |
| # Run "make veryclean" to remove all staging and make.log files. |
| # |
| # For the sake of simplicity, the "standard" installation can be done |
| # with the usual |
| # |
| # make |
| # make install |
| # make clean |
| # |
| #-------------------------------------------------------------------- |
| # This Makefile contains bash-isms |
| SHELL = bash |
| MV = mv |
| SED = @SED@ |
| |
| prefix = @prefix@ |
| datarootdir = @datarootdir@ |
| datadir = @datadir@ |
| |
| # Use git revision if this is a cloned repo; otherwise get the revision |
| # from the VERSION file in the directory above. |
| GITREV = $(shell git describe --long) |
| ifeq (${GITREV},) |
| REVISION = $(shell cat ../VERSION) |
| else |
| REVISION = ${GITREV} |
| endif |
| TECH = sky130 |
| |
| # The run-time environment uses PDKPATH to override the PDK location, |
| # so prevent that from happening during PDK install. |
| unexport PDKPATH |
| |
| # If EF_STYLE is set to 1, then efabless naming conventions are |
| # used, otherwise the generic naming conventions are used. |
| # Mainly, the hierarchy of library names and file types is reversed |
| # (e.g., sky130_fd_sc_hd/lef vs. lef/sky130_fd_sc_hd). |
| |
| # EF_STYLE = 0 | 1 |
| EF_STYLE = @EF_STYLE@ |
| |
| # Normally it's fine to keep the staging path in a local directory, |
| # although /tmp or a dedicated staging area are also fine, as long |
| # as the install process can write to the path. |
| |
| STAGING_PATH = $(shell pwd) |
| |
| SHARED_PDKS_PATH = $(datadir)/pdk |
| |
| # If LINK_TARGETS is set to "none", then files are copied |
| # from the SkyWater sources to the target. If set to "source", |
| # symbolic links are made in the target directories pointing |
| # back to the SkyWater sources. If set to the name of another |
| # PDK (e.g, "sky130A"), then symbolic links are made to the |
| # same files in that PDK, where they exist, and are copied |
| # from source, where they don't. |
| |
| # LINK_TARGETS = source | none | sky130A |
| LINK_TARGETS = @SKY130_LINK_TARGETS@ |
| |
| # Paths: |
| |
| # Path to skywater_pdk |
| SKYWATER_PATH = @SKY130_SOURCE_PATH@ |
| ifneq ($(SKYWATER_PATH),) |
| SKYWATER_LIBS_PATH = ${SKYWATER_PATH}/libraries |
| else |
| SKYWATER_LIBS_PATH = |
| endif |
| |
| # Path to independent library sources (to be added to configuration options). |
| ALPHA_PATH = @SKY130_ML_XX_HD_PATH@ |
| XSCHEM_PATH = @XSCHEM_SKY130_PATH@ |
| SRAM_PATH = @SKY130_SRAM_MACROS_PATH@ |
| OSU_PATH = @SKY130_OSU_PATH@ |
| OSU_T12_PATH = @SKY130_OSU_T12_PATH@ |
| OSU_T15_PATH = @SKY130_OSU_T15_PATH@ |
| OSU_T18_PATH = @SKY130_OSU_T18_PATH@ |
| |
| PDK_URL = https://github.com/google/skywater-pdk |
| ALPHA_URL = https://github.com/PaulSchulz/sky130_pschulz_xx_hd |
| XSCHEM_URL = https://github.com/StefanSchippers/xschem_sky130 |
| SRAM_URL = https://github.com/efabless/sky130_sram_macros |
| OSU_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc |
| OSU_T12_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t12 |
| OSU_T15_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t15 |
| OSU_T18_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t18 |
| |
| # NOTE: Install destination is the git repository of the technology platform. |
| # Once updated in git, the git project can be distributed to all hosts. |
| # |
| ifeq (${EF_STYLE}, 1) |
| CONFIG_DIR = .ef-config |
| REV_DIR = ${REVISION} |
| else |
| CONFIG_DIR = .config |
| REV_DIR = . |
| endif |
| |
| # EF process nodes created from the master sources |
| SKY130A = sky130A |
| |
| ifeq (${LINK_TARGETS}, ${SKY130A}) |
| DIST_LINK_TARGETS = ${SHARED_PDKS_PATH}/${LINK_TARGETS} |
| else |
| DIST_LINK_TARGETS = ${LINK_TARGETS} |
| endif |
| |
| # Basic definitions for each EF process node |
| SKY130A_DEFS = -DTECHNAME=sky130A -DREVISION=${REVISION} |
| |
| # Module definitions for each process node |
| # (Note that MOS is default and therefore not used anywhere) |
| SKY130A_DEFS += -DMETAL5 -DMIM -DREDISTRIBUTION |
| # SKY130A_DEFS += -DMETAL5 -DMIM |
| |
| # Add staging path |
| SKY130A_DEFS += -DSTAGING_PATH=${STAGING_PATH} |
| |
| # Record commit numbers for the nodeinfo.json file |
| OPEN_PDKS_COMMIT = $(shell git rev-parse HEAD) |
| ifeq (${OPEN_PDKS_COMMIT},) |
| COMMIT_DEFS = -DOPEN_PDKS_COMMIT=${REVISION} |
| else |
| COMMIT_DEFS = -DOPEN_PDKS_COMMIT=${OPEN_PDKS_COMMIT} |
| endif |
| ifeq (${ALPHA_PATH},) |
| COMMIT_DEFS += -DALPHA_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DALPHA_COMMIT=$(shell cd ${ALPHA_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${SRAM_PATH},) |
| COMMIT_DEFS += -DSRAM_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DSRAM_COMMIT=$(shell cd ${SRAM_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${OSU_PATH},) |
| COMMIT_DEFS += -DOSU_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DOSU_COMMIT=$(shell cd ${OSU_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${OSU_T12_PATH},) |
| COMMIT_DEFS += -DOSU_T12_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DOSU_T12_COMMIT=$(shell cd ${OSU_T12_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${OSU_T15_PATH},) |
| COMMIT_DEFS += -DOSU_T15_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DOSU_T15_COMMIT=$(shell cd ${OSU_T15_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${OSU_T18_PATH},) |
| COMMIT_DEFS += -DOSU_T18_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DOSU_T18_COMMIT=$(shell cd ${OSU_T18_PATH} ; git rev-parse HEAD) |
| endif |
| ifeq (${SKYWATER_PATH},) |
| COMMIT_DEFS += -DFD_PR_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_IO_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_HD_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_HDLL_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_HVL_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_HS_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_MS_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_LS_COMMIT="unknown" |
| COMMIT_DEFS += -DFD_SC_LP_COMMIT="unknown" |
| else |
| COMMIT_DEFS += -DFD_PR_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_pr/latest) |
| COMMIT_DEFS += -DFD_IO_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_io/latest) |
| COMMIT_DEFS += -DFD_SC_HD_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hd/latest) |
| COMMIT_DEFS += -DFD_SC_HDLL_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hdll/latest) |
| COMMIT_DEFS += -DFD_SC_HVL_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hvl/latest) |
| COMMIT_DEFS += -DFD_SC_HS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hs/latest) |
| COMMIT_DEFS += -DFD_SC_MS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_ms/latest) |
| COMMIT_DEFS += -DFD_SC_LS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_ls/latest) |
| COMMIT_DEFS += -DFD_SC_LP_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_lp/latest) |
| endif |
| COMMIT_DEFS += -DMAGIC_VERSION=$(shell magic -dnull -noconsole --version) |
| COMMIT_DEFS += -DOPEN_PDKS_VERSION=$(shell cat ../VERSION) |
| |
| ifeq (${EF_STYLE}, 1) |
| EF_FORMAT = -ef_format |
| SKY130A_DEFS += -DEF_FORMAT |
| else |
| EF_FORMAT = -std_format |
| endif |
| |
| MAGICTOP = libs.tech/magic |
| NETGENTOP = libs.tech/netgen |
| IRSIMTOP = libs.tech/irsim |
| QFLOWTOP = libs.tech/qflow |
| KLAYOUTTOP = libs.tech/klayout |
| OPENLANETOP = libs.tech/openlane |
| XSCHEMTOP = libs.tech/xschem |
| XCIRCUITTOP = libs.tech/xcircuit |
| NGSPICETOP = libs.tech/ngspice |
| |
| ifeq (${EF_STYLE}, 1) |
| MAGICPATH = ${MAGICTOP}/${REVISION} |
| MAGICCURRENT = ${MAGICTOP}/current |
| else |
| MAGICPATH = ${MAGICTOP} |
| MAGICCURRENT = ${MAGICTOP} |
| endif |
| |
| # Currently, netgen, qflow, irsim, and klayout do not use revisioning (needs to change!) |
| NETGENPATH = ${NETGENTOP} |
| IRSIMPATH = ${IRSIMTOP} |
| QFLOWPATH = ${QFLOWTOP} |
| KLAYOUTPATH = ${KLAYOUTTOP} |
| OPENLANEPATH = ${OPENLANETOP} |
| XSCHEMPATH = ${XSCHEMTOP} |
| XCIRCUITPATH = ${XCIRCUITTOP} |
| NGSPICEPATH = ${NGSPICETOP} |
| |
| MAGICTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${MAGICTOP} |
| NETGENTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NETGENTOP} |
| IRSIMTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${IRSIMTOP} |
| QFLOWTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${QFLOWTOP} |
| KLAYOUTTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${KLAYOUTTOP} |
| OPENLANETOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${OPENLANETOP} |
| XSCHEMTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XSCHEMTOP} |
| XCIRCUITTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XCIRCUITTOP} |
| NGSPICETOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NGSPICETOP} |
| |
| MAGIC_STAGING_A = ${STAGING_PATH}/${SKY130A}/${MAGICPATH} |
| NETGEN_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NETGENPATH} |
| IRSIM_STAGING_A = ${STAGING_PATH}/${SKY130A}/${IRSIMPATH} |
| QFLOW_STAGING_A = ${STAGING_PATH}/${SKY130A}/${QFLOWPATH} |
| KLAYOUT_STAGING_A = ${STAGING_PATH}/${SKY130A}/${KLAYOUTPATH} |
| OPENLANE_STAGING_A = ${STAGING_PATH}/${SKY130A}/${OPENLANEPATH} |
| XSCHEM_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XSCHEMPATH} |
| XCIRCUIT_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XCIRCUITPATH} |
| NGSPICE_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NGSPICEPATH} |
| |
| SKY130A_DEFS += -DMAGIC_CURRENT=${MAGICCURRENT} |
| |
| # Openlane has a number of files that are common to all digital |
| # standard cell libraries, so these are collected in one definition |
| # here: |
| OPENLANE_COMMON = config.tcl tracks.info no_synth.cells drc_exclude.cells |
| OPENLANE_COMMON += tribuff_map.v latch_map.v mux2_map.v mux4_map.v fa_map.v rca_map.v csa_map.v |
| |
| # Where cpp syntax is followed, this is equivalent to cpp, but it does not |
| # mangle non-C source files under the belief that they are actually C code. |
| CPP = ../common/preproc.py |
| |
| # The following script in the ../common directory does most of the work of |
| # copying or linking the foundry vendor files to the target directory. |
| STAGE = set -f ; ../common/foundry_install.py ${EF_FORMAT} |
| ifneq ($(DESTDIR), ) |
| INSTALL = ../common/staging_install.py -local $(DESTDIR) ${EF_FORMAT} |
| else |
| INSTALL = ../common/staging_install.py ${EF_FORMAT} |
| endif |
| |
| # The script(s) below are used for custom changes to the vendor PDK files |
| ADDPROP = ../common/insert_property.py ${EF_FORMAT} |
| |
| # List the EDA tools to install local setup files for |
| TOOLS = |
| |
| # KLAYOUT_DISABLED = 0 | 1 |
| KLAYOUT_DISABLED = @KLAYOUT_DISABLED@ |
| ifneq (${KLAYOUT_DISABLED}, 1) |
| TOOLS += klayout |
| endif |
| |
| # OPENLANE_DISABLED = 0 | 1 |
| OPENLANE_DISABLED = @OPENLANE_DISABLED@ |
| ifneq (${OPENLANE_DISABLED}, 1) |
| TOOLS += openlane |
| endif |
| |
| # QFLOW_DISABLED = 0 | 1 |
| QFLOW_DISABLED = @QFLOW_DISABLED@ |
| ifneq (${QFLOW_DISABLED}, 1) |
| TOOLS += qflow |
| endif |
| |
| # MAGIC_DISABLED = 0 | 1 |
| MAGIC_DISABLED = @MAGIC_DISABLED@ |
| ifneq (${MAGIC_DISABLED}, 1) |
| TOOLS += magic |
| endif |
| |
| # NETGEN_DISABLED = 0 | 1 |
| NETGEN_DISABLED = @NETGEN_DISABLED@ |
| ifneq (${NETGEN_DISABLED}, 1) |
| TOOLS += netgen |
| endif |
| |
| # IRSIM_DISABLED = 0 | 1 |
| IRSIM_DISABLED = @IRSIM_DISABLED@ |
| ifneq (${IRSIM_DISABLED}, 1) |
| TOOLS += irsim |
| endif |
| |
| # XSCHEM_DISABLED = 0 | 1 |
| XSCHEM_DISABLED = @XSCHEM_DISABLED@ |
| ifneq (${XSCHEM_DISABLED}, 1) |
| TOOLS += xschem |
| endif |
| |
| # XCIRCUIT_DISABLED = 0 | 1 |
| XCIRCUIT_DISABLED = @XCIRCUIT_DISABLED@ |
| ifneq (${XCIRCUIT_DISABLED}, 1) |
| TOOLS += xcircuit |
| endif |
| |
| # These definitions depend on the setting of EF_STYLE |
| ifeq (${EF_STYLE}, 1) |
| IO_VERILOG = verilog/sky130_fd_io |
| HD_VERILOG = verilog/sky130_fd_sc_hd |
| HDLL_VERILOG = verilog/sky130_fd_sc_hdll |
| HVL_VERILOG = verilog/sky130_fd_sc_hvl |
| HS_VERILOG = verilog/sky130_fd_sc_hs |
| MS_VERILOG = verilog/sky130_fd_sc_ms |
| LS_VERILOG = verilog/sky130_fd_sc_ls |
| LP_VERILOG = verilog/sky130_fd_sc_lp |
| HD_TECHLEF = techLEF/sky130_fd_sc_hd |
| HDLL_TECHLEF = techLEF/sky130_fd_sc_hdll |
| MLXX_SCRIPTS = scripts/sky130_ml_xx_hd |
| PR_SPICE = spi/sky130_fd_pr |
| HVL_SPICE = spi/sky130_fd_sc_hvl |
| HD_SPICE = spi/sky130_fd_sc_hd |
| HVL_PATCH4 = 4b |
| HVL_CDL = cdl/sky130_fd_sc_hvl |
| else |
| IO_VERILOG = sky130_fd_io/verilog |
| HD_VERILOG = sky130_fd_sc_hd/verilog |
| HDLL_VERILOG = sky130_fd_sc_hdll/verilog |
| HVL_VERILOG = sky130_fd_sc_hvl/verilog |
| HS_VERILOG = sky130_fd_sc_hs/verilog |
| MS_VERILOG = sky130_fd_sc_ms/verilog |
| LS_VERILOG = sky130_fd_sc_ls/verilog |
| LP_VERILOG = sky130_fd_sc_lp/verilog |
| HD_TECHLEF = sky130_fd_sc_hd/techlef |
| HDLL_TECHLEF = sky130_fd_sc_hdll/techlef |
| MLXX_SCRIPTS = sky130_ml_xx_hd/scripts |
| PR_SPICE = sky130_fd_pr/spice |
| HVL_SPICE = sky130_fd_sc_hvl/spice |
| HD_SPICE = sky130_fd_sc_hd/spice |
| HVL_PATCH4 = 4 |
| HVL_CDL = sky130_fd_sc_hvl/cdl |
| endif |
| |
| all: all-a |
| |
| # Handle prerequisites (fetch and install the PDK and requested libraries) |
| prerequisites: pdk-repo alpha-repo xschem-repo sram-repo osu-repo osu-t12-repo osu-t15-repo osu-t18-repo |
| |
| pdk-repo: |
| if test "x${SKYWATER_PATH}" != "x" ; then \ |
| if test -d "${SKYWATER_PATH}" ; then \ |
| echo "Using existing installation of SkyWater PDK from ${SKYWATER_PATH}" ; \ |
| else \ |
| echo "Downloading SkyWater PDK from ${PDK_URL}" ; \ |
| custom/scripts/pdk_download.sh ${PDK_URL} ${SKYWATER_PATH} ; \ |
| fi ; \ |
| fi |
| |
| alpha-repo: |
| if test "x${ALPHA_PATH}" != "x" ; then \ |
| if test -d "${ALPHA_PATH}" ; then \ |
| echo "Using existing installation of alphanumeric library from ${ALPHA_PATH}" ; \ |
| else \ |
| echo "Downloading alphanumeric library from ${ALPHA_URL}" ; \ |
| ../scripts/download.sh ${ALPHA_URL} ${ALPHA_PATH} ; \ |
| fi ; \ |
| fi |
| |
| sram-repo: |
| if test "x${SRAM_PATH}" != "x" ; then \ |
| if test -d "${SRAM_PATH}" ; then \ |
| echo "Using existing installation of SRAM macro library from ${SRAM_PATH}" ; \ |
| else \ |
| echo "Downloading SRAM macro library from ${SRAM_URL}" ; \ |
| ../scripts/download.sh ${SRAM_URL} ${SRAM_PATH} ; \ |
| fi ; \ |
| fi |
| |
| xschem-repo: |
| if test "x${XSCHEM_PATH}" != "x" ; then \ |
| if test -d "${XSCHEM_PATH}" ; then \ |
| echo "Using existing installation of xschem setup from ${XSCHEM_PATH}" ; \ |
| else \ |
| echo "Downloading xschem setup from ${XSCHEM_URL}" ; \ |
| ../scripts/download.sh ${XSCHEM_URL} ${XSCHEM_PATH} ; \ |
| fi ; \ |
| fi |
| |
| osu-repo: |
| if test "x${OSU_PATH}" != "x" ; then \ |
| if test -d "${OSU_PATH}" ; then \ |
| echo "Using existing installation of OSU standard cell library from ${OSU_PATH}" ; \ |
| else \ |
| echo "Downloading OSU standard cell library from ${OSU_URL}" ; \ |
| ../scripts/download.sh ${OSU_URL} ${OSU_PATH} 0 ; \ |
| fi ; \ |
| fi |
| |
| osu-t12-repo: |
| if test "x${OSU_T12_PATH}" != "x" ; then \ |
| if test -d "${OSU_T12_PATH}" ; then \ |
| echo "Using existing installation of OSU T12 standard cell library from ${OSU_T12_PATH}" ; \ |
| else \ |
| echo "Downloading OSU standard T12 cell library from ${OSU_T12_URL}" ; \ |
| ../scripts/download.sh ${OSU_T12_URL} ${OSU_T12_PATH} 0 ; \ |
| fi ; \ |
| fi |
| |
| osu-t15-repo: |
| if test "x${OSU_T15_PATH}" != "x" ; then \ |
| if test -d "${OSU_T15_PATH}" ; then \ |
| echo "Using existing installation of OSU T15 standard cell library from ${OSU_T15_PATH}" ; \ |
| else \ |
| echo "Downloading OSU standard T15 cell library from ${OSU_T15_URL}" ; \ |
| ../scripts/download.sh ${OSU_T15_URL} ${OSU_T15_PATH} 0 ; \ |
| fi ; \ |
| fi |
| |
| osu-t18-repo: |
| if test "x${OSU_T18_PATH}" != "x" ; then \ |
| if test -d "${OSU_T18_PATH}" ; then \ |
| echo "Using existing installation of OSU T18 standard cell library from ${OSU_T18_PATH}" ; \ |
| else \ |
| echo "Downloading OSU standard T18 cell library from ${OSU_T18_URL}" ; \ |
| ../scripts/download.sh ${OSU_T18_URL} ${OSU_T18_PATH} 0 ; \ |
| fi ; \ |
| fi |
| |
| all-a: prerequisites |
| echo "Starting sky130A PDK staging on "`date` > ${SKY130A}_make.log |
| ${MAKE} general-a |
| ${MAKE} tools-a |
| ${MAKE} vendor-a |
| echo "Ended sky130A PDK staging on "`date` >> ${SKY130A}_make.log |
| |
| general-a: ${TECH}.json |
| mkdir -p ${STAGING_PATH}/${SKY130A}/${CONFIG_DIR} |
| rm -f ${STAGING_PATH}/${SKY130A}/${CONFIG_DIR}/nodeinfo.json |
| ${CPP} ${SKY130A_DEFS} ${COMMIT_DEFS} ${TECH}.json \ |
| ${STAGING_PATH}/${SKY130A}/${CONFIG_DIR}/nodeinfo.json |
| |
| tools-a: $(addsuffix -a, $(TOOLS)) |
| |
| magic-a: magic/${TECH}.tech magic/${TECH}gds.tech magic/${TECH}.magicrc magic/${TECH}.tcl |
| mkdir -p ${MAGICTOP_STAGING_A} |
| mkdir -p ${MAGIC_STAGING_A} |
| rm -f ${MAGICTOP_STAGING_A}/current |
| rm -f ${MAGIC_STAGING_A}/${SKY130A}.tech |
| rm -f ${MAGIC_STAGING_A}/${SKY130A}-GDS.tech |
| rm -f ${MAGIC_STAGING_A}/${SKY130A}.tcl |
| rm -f ${MAGIC_STAGING_A}/${SKY130A}-BindKeys |
| rm -f ${MAGIC_STAGING_A}/magicrc |
| if test "${EF_STYLE}" == "1" ; then \ |
| (cd ${MAGICTOP_STAGING_A} ; ln -s ${REV_DIR} current) ; \ |
| fi |
| cp -rp custom/scripts/seal_ring_generator ${MAGIC_STAGING_A}/. |
| cp -rp custom/scripts/bump_bond_generator ${MAGIC_STAGING_A}/. |
| cp custom/scripts/generate_fill.py ${MAGIC_STAGING_A}/. |
| cp custom/scripts/check_density.py ${MAGIC_STAGING_A}/. |
| cp custom/scripts/run_standard_drc.py ${MAGIC_STAGING_A}/. |
| cp custom/scripts/check_antenna.py ${MAGIC_STAGING_A}/. |
| ${CPP} ${SKY130A_DEFS} magic/${TECH}.tech ${MAGIC_STAGING_A}/${SKY130A}.tech |
| ${CPP} ${SKY130A_DEFS} magic/${TECH}gds.tech ${MAGIC_STAGING_A}/${SKY130A}-GDS.tech |
| ${CPP} ${SKY130A_DEFS} magic/${TECH}.magicrc ${MAGIC_STAGING_A}/${SKY130A}.magicrc |
| ${CPP} ${SKY130A_DEFS} ../common/pdk.bindkeys ${MAGIC_STAGING_A}/${SKY130A}-BindKeys |
| ${CPP} ${SKY130A_DEFS} magic/${TECH}.tcl ${MAGIC_STAGING_A}/${SKY130A}.tcl |
| ${CPP} ${SKY130A_DEFS} ../common/pdk.tcl >> ${MAGIC_STAGING_A}/${SKY130A}.tcl |
| |
| qflow-a: qflow/${TECH}.sh qflow/${TECH}.par |
| mkdir -p ${QFLOWTOP_STAGING_A} |
| mkdir -p ${QFLOW_STAGING_A} |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hd.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hd.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hdll.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hdll.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hs.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hs.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hvl.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_hvl.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_ls.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_ls.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_lp.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_lp.par |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_ms.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_fd_sc_ms.par |
| rm -f ${QFLOW_STAGING_A}/sky130_osu_sc_t18.sh |
| rm -f ${QFLOW_STAGING_A}/sky130_osu_sc_t18.par |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_hd qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_hd.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_hdll qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_hdll.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_hvl qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_hvl.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_hs qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_hs.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_lp qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_lp.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_ls qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_ls.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_fd_sc_ms qflow/${TECH}.sh \ |
| ${QFLOW_STAGING_A}/sky130_fd_sc_ms.sh |
| ${CPP} ${SKY130A_DEFS} -DLIBRARY=sky130_osu_sc_t18 qflow/sky130osu.sh \ |
| ${QFLOW_STAGING_A}/sky130_osu_sc_t18.sh |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_hd.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_hdll.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_hvl.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_hs.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_ms.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/$sky130_fd_sc_lp.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_fd_sc_ls.par |
| ${CPP} ${SKY130A_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_A}/sky130_osu_sc_t18.par |
| |
| netgen-a: netgen/${TECH}_setup.tcl |
| mkdir -p ${NETGENTOP_STAGING_A} |
| mkdir -p ${NETGEN_STAGING_A} |
| rm -f ${NETGEN_STAGING_A}/${SKY130A}_setup.tcl |
| rm -f ${NETGEN_STAGING_A}/setup.tcl |
| ${CPP} ${SKY130A_DEFS} netgen/${TECH}_setup.tcl ${NETGEN_STAGING_A}/${SKY130A}_setup.tcl |
| (cd ${NETGEN_STAGING_A} ; ln -s ${SKY130A}_setup.tcl setup.tcl) |
| |
| irsim-a: irsim |
| mkdir -p ${IRSIMTOP_STAGING_A} |
| mkdir -p ${IRSIM_STAGING_A} |
| rm -f ${IRSIM_STAGING_A}/${SKY130A}_*.prm |
| cp irsim/${SKY130A}_*.prm ${IRSIM_STAGING_A}/ |
| |
| klayout-a: klayout/${TECH}.lyp klayout/${TECH}.lyt |
| mkdir -p ${KLAYOUTTOP_STAGING_A} |
| mkdir -p ${KLAYOUT_STAGING_A} |
| rm -f ${KLAYOUT_STAGING_A}/${SKY130A}.lyp |
| rm -f ${KLAYOUT_STAGING_A}/${SKY130A}.lyt |
| ${CPP} ${SKY130A_DEFS} klayout/${TECH}.lyp ${KLAYOUT_STAGING_A}/${SKY130A}.lyp |
| ${CPP} ${SKY130A_DEFS} klayout/${TECH}.lyt ${KLAYOUT_STAGING_A}/${SKY130A}.lyt |
| cp klayout/${TECH}.lydrc ${KLAYOUT_STAGING_A}/${SKY130A}.lydrc |
| ./custom/scripts/gen_run_drc.py -l ${KLAYOUT_STAGING_A}/${SKY130A}.lydrc -o ${KLAYOUT_STAGING_A}/${SKY130A}.drc |
| |
| xcircuit-a: xcircuit/${TECH}.xcircuitrc |
| rm -rf ${XCIRCUIT_STAGING_A} |
| mkdir -p ${XCIRCUITTOP_STAGING_A} |
| mkdir -p ${XCIRCUIT_STAGING_A} |
| rm -f ${XCIRCUIT_STAGING_A}/*.lps |
| rm -f ${XCIRCUIT_STAGING_A}/${SKY130A}.xcircuitrc |
| ${CPP} ${SKY130A_DEFS} xcircuit/ngspice.lps ${XCIRCUIT_STAGING_A}/ngspice.lps |
| ${CPP} ${SKY130A_DEFS} xcircuit/sky130_fd_pr.lps ${XCIRCUIT_STAGING_A}/sky130_fd_pr.lps |
| ${CPP} ${SKY130A_DEFS} xcircuit/sky130_fd_sc_hd.lps ${XCIRCUIT_STAGING_A}/sky130_fd_sc_hd.lps |
| ${CPP} ${SKY130A_DEFS} xcircuit/${TECH}.xcircuitrc ${XCIRCUIT_STAGING_A}/${SKY130A}.xcircuitrc |
| |
| xschem-a: ${XSCHEM_PATH} |
| rm -rf ${XSCHEM_STAGING_A} |
| mkdir -p ${XSCHEMTOP_STAGING_A} |
| mkdir -p ${XSCHEM_STAGING_A} |
| # Copy the entire repository (other than .git, if it exists) |
| if test "x${XSCHEM_PATH}" != "x" ; then \ |
| cp -rp ${XSCHEM_PATH}/* ${XSCHEM_STAGING_A} ; \ |
| fi |
| |
| #add the correct libraries into the test files |
| for file in ${XSCHEM_STAGING_A}/sky130_tests/* ; do \ |
| ${SED} -i '/.include \\\\\\\\$$\:\:SKYWATER_MODELS/d' $$file ; \ |
| grep -zl 'sky130.lib.spice' $$file || ${SED} -z 's|format="tcleval( @value )"\nvalue="|format="tcleval( @value )"\nvalue="\n.lib \\\\\\\\$$\:\:SKYWATER_MODELS\\\\\\\\/sky130.lib.spice tt |' -i $$file ; \ |
| grep -zl 'format="tcleval( @value )".*value="' $$file || printf 'C {devices/code.sym} -170 0 0 0 {name=TT_MODELS\nonly_toplevel=true\nformat="tcleval( @value )"\nvalue="\n.lib \\\\\\\\$$\:\:SKYWATER_MODELS\\\\\\\\/sky130.lib.spice tt\n"}' >> $$file ; \ |
| done |
| |
| # Re-copy the xschemrc, with one change to add the PDK install path as |
| # a component of XSCHEM_LIBRARY_PATH |
| cat ${XSCHEM_PATH}/xschemrc | \ |
| ${SED} -e "/PWD/aappend XSCHEM_LIBRARY_PATH :${XSCHEM_STAGING_A}" | \ |
| ${SED} -e "/sky130_models.tcl/s#scripts#${XSCHEM_STAGING_A}/scripts#" | \ |
| ${SED} -e "/netlist_dir/aset netlist_dir ." | \ |
| ${SED} -e "/SKYWATER_MODELS/s#~/pdks/sky130A/libs.tech/ngspice#${NGSPICE_STAGING_A}#" | \ |
| ${SED} -e "/SKYWATER_STDCELLS/s#~/pdks/sky130A/libs.ref/sky130_fd_sc_hd/spice#${STAGING_PATH}/${SKY130A}/libs.ref/${HD_SPICE}#" \ |
| > ${XSCHEM_STAGING_A}/xschemrc |
| |
| openlane-a: openlane/common_pdn.tcl openlane/config.tcl openlane/sky130_fd_sc_hd/config.tcl openlane/sky130_fd_sc_hs/config.tcl openlane/sky130_fd_sc_ms/config.tcl openlane/sky130_fd_sc_ls/config.tcl openlane/sky130_fd_sc_hdll/config.tcl openlane/sky130_osu_sc_t18/config.tcl |
| mkdir -p ${OPENLANETOP_STAGING_A} |
| mkdir -p ${OPENLANE_STAGING_A} |
| rm -rf ${OPENLANE_STAGING_A}/custom_cells/* |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_hd |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_hs |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_ls |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_ms |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_hdll |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_fd_sc_hvl |
| mkdir -p ${OPENLANE_STAGING_A}/sky130_osu_sc_t18 |
| rm -f ${OPENLANE_STAGING_A}/common_pdn.info |
| rm -f ${OPENLANE_STAGING_A}/config.tcl |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_hd/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_hs/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_hdll/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_ls/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_ms/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_fd_sc_hvl/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| rm -f ${OPENLANE_STAGING_A}/sky130_osu_sc_t18/$$file ; \ |
| done |
| |
| cp -r openlane/custom_cells ${OPENLANE_STAGING_A} |
| ${CPP} ${SKY130A_DEFS} openlane/common_pdn.tcl ${OPENLANE_STAGING_A}/common_pdn.tcl |
| ${CPP} ${SKY130A_DEFS} openlane/config.tcl ${OPENLANE_STAGING_A}/config.tcl |
| |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_hd/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_hd/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_hs/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_hs/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_ms/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_ms/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_ls/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_ls/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_hdll/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_hdll/$$file ; \ |
| done |
| for file in ${OPENLANE_COMMON} ; do \ |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_fd_sc_hvl/$$file \ |
| ${OPENLANE_STAGING_A}/sky130_fd_sc_hvl/$$file ; \ |
| done |
| |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_osu_sc_t18/config.tcl \ |
| ${OPENLANE_STAGING_A}/sky130_osu_sc_t18/config.tcl |
| ${CPP} -quiet ${SKY130A_DEFS} openlane/sky130_osu_sc_t18/tracks.info \ |
| ${OPENLANE_STAGING_A}/sky130_osu_sc_t18/tracks.info |
| |
| vendor-a: |
| # Build targets conditionally based on what repositories or submodules |
| # were selected or initialized. To be done: Allow a library version |
| # to be specified that overrides "latest". |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_pr/latest/cells ; then \ |
| echo "Building primitives library and simulation models" ;\ |
| make primitive-a;\ |
| fi |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_io/latest/cells ; then \ |
| echo "Building padframe I/O libraries" ;\ |
| make io-a ;\ |
| fi |
| # This assumes that at least the HD library submodule exists. Also it |
| # assumes that the same library version is used for all libraries, which |
| # is fine with "latest" but otherwise probably invalid. |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_hd/latest/cells ; then \ |
| echo "Building digital standard cell libraries" ;\ |
| make digital-a ;\ |
| fi |
| if test -d ${ALPHA_PATH} ; then \ |
| echo "Building alphanumeric layout libraries" ;\ |
| make alpha-a ;\ |
| fi |
| if test -d ${SRAM_PATH} ; then \ |
| echo "Building SRAM macro library" ;\ |
| make sram-a ;\ |
| fi |
| if test -d ${OSU_PATH} ; then \ |
| echo "Building OSU full source library" ;\ |
| make osu-base-a ;\ |
| fi |
| if test -d ${OSU_T12_PATH} ; then \ |
| echo "Building OSU 12-track-high standard cell library" ;\ |
| make osu-t12-a ;\ |
| fi |
| if test -d ${OSU_T15_PATH} ; then \ |
| echo "Building OSU 15-track-high standard cell library" ;\ |
| make osu-t15-a ;\ |
| fi |
| if test -d ${OSU_T18_PATH} ; then \ |
| echo "Building OSU 18-track-high standard cell library" ;\ |
| make osu-t18-a ;\ |
| fi |
| |
| primitive-a: |
| # Install device subcircuits from vendor files |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -ngspice sky130_fd_pr/latest/models/* \ |
| filter=custom/scripts/rename_models.py ${EF_FORMAT} \ |
| 2>&1 | tee -a ${SKY130A}_make.log |
| # Install device layouts from custom sources |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130A} \ |
| -gds sky130_fd_pr/*.gds \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library primitive sky130_fd_pr 2>&1 | tee -a ${SKY130A}_make.log |
| # Install base device library from vendor files |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -gds %l/latest/cells/*/*.gds \ |
| exclude=sky130_fd_pr__pnp_05v5_W3p40L3p40.gds,sky130_fd_pr__npn_11v0_W1p00L1p00.gds \ |
| compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -cdl %l/latest/cells/*/*.cdl compile-only \ |
| -lef %l/latest/cells/*/*.magic.lef compile-only \ |
| -spice %l/latest/cells/*/*.spice filter=custom/scripts/rename_cells.py \ |
| -library primitive sky130_fd_pr 2>&1 | tee -a ${SKY130A}_make.log |
| # Custom: Add "short" resistor model and subcircuit to the r+c models file |
| cat ./custom/models/short.spice >> \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice |
| # Custom: Add diodes as subcircuits to the r+c models file |
| cat ./custom/models/diode.spice >> \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice |
| # Custom: Add resistors as subcircuits to the r+c models file |
| cat ./custom/models/resistor.spice >> \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice |
| |
| # Custom: Patch the models to work around ngspice issue with the relative |
| # order of the "nf" and "mult" parameters. |
| patch -p4 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE} \ |
| < custom/patches/sky130_fd_pr.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| patch -p1 -f -d ${STAGING_PATH}/${SKY130A} \ |
| < custom/patches/sky130_fd_pr_2.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Patch the models to remove the substrate pin from the PNP |
| # device, which has no independent substrate pin (collector=substrate) |
| patch -p4 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE} \ |
| < custom/patches/sky130_fd_pr_3.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Patch the ngspice models to add the HV diffusion resistor subcircuits |
| patch -p2 -f -d ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice \ |
| < custom/patches/sky130_fd_pr_5.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Fix up the PNP model file before running the next modification |
| head -15 ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice > ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/temp |
| tail -39 ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice >> ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/temp |
| mv ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/temp ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice |
| # Custom: Add the PNP 3.4x3.4um device model to the includes in "all.spice" |
| ./custom/scripts/fix_spice_includes.py ${EF_FORMAT} \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/all.spice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Parse the (commented out) statistics blocks and generate |
| # ngspice-compatible monte carlo parameters for mismatch and process |
| ./custom/scripts/mismatch_params.py ${EF_FORMAT} \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| ./custom/scripts/mismatch_params.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| ./custom/scripts/process_params.py \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| ./custom/scripts/montecarlo_hack.py \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Change vt to local_vt in one file for Xyce compatibilty |
| ./custom/scripts/xyce_hack.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__res_iso_pw.model.spice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Remove ACM model parameters from BSIM3 devices |
| ./custom/scripts/xyce_hack2.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_nfet_pass.pm3.spice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| ./custom/scripts/xyce_hack2.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_pfet_pass.pm3.spice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| ./custom/scripts/xyce_hack2.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_nfet_latch.pm3.spice \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| |
| # Custom: Make corrections/additions so sky130.lib.spice |
| ./custom/scripts/build_lib_spice.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/sky130.lib.spice \ |
| custom/models/sky130.lib.spice.extra \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Add special device ID layers to bipolar layouts in magic |
| # to make the extraction models correct. |
| ./custom/scripts/add_bipolar_ids.py ${EF_FORMAT} \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| |
| # Custom: Add "spinit" file |
| cat ./custom/models/spinit >> \ |
| ${STAGING_PATH}/${SKY130A}/libs.tech/ngspice/spinit |
| |
| io-a: |
| # Install custom additions to I/O pad library |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130A} \ |
| -verilog %l/verilog/*.v \ |
| -cdl %l/cdl/*.cdl \ |
| -spice %l/spice/*.spice \ |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ |
| -lef %l/lef/*.lef compile-only rename=sky130_ef_io \ |
| -library general sky130_fd_io 2>&1 | tee -a ${SKY130A}_make.log |
| # Install SkyWater I/O pad library |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ |
| exclude=*.magic.lef,sky130_ef_io.lef \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -doc %l/latest/cells/*/*.pdf \ |
| -lib %l/latest/timing/*.lib \ |
| -gds %l/latest/cells/*/*.gds compile-only \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| options=custom/scripts/sky130_fd_io_import.tcl \ |
| -verilog %l/latest/cells/*/*.*.v \ |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v \ |
| compile-only filter=custom/scripts/inc_verilog.py \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -library general sky130_fd_io 2>&1 | tee -a ${SKY130A}_make.log |
| # Remove the base verilog files which have already been included into |
| # the libraries |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${IO_VERILOG}/*.*.v |
| # Add a maskhint set for the GPIO pad .mag view to prevent problems writing |
| # when writing HVI to GDS during hierarchical adjustments. |
| ${ADDPROP} ${STAGING_PATH}/${SKY130A} sky130_fd_io sky130_fd_io__top_gpiov2 \ |
| "MASKHINTS_HVI 1346 17198 5828 19224 13700 1890 15920 2360 24 17522 1778 20612" -mag |
| |
| digital-a: |
| # Install custom additions to standard cell libraries |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130A} \ |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ |
| -lef %l/lef/*.lef \ |
| -verilog %l/verilog/*.v \ |
| -library digital sky130_fd_sc_hd 2>&1 | tee -a ${SKY130A}_make.log |
| # Install all SkyWater digital standard cells. |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef %l/latest/tech/*.tlef \ |
| -spice %l/latest/cells/*/*.spice compile-only \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| filter=custom/scripts/fix_device_models.py \ |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -lef %l/latest/cells/*/*.magic.lef compile-only \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -doc %l/latest/cells/*/*.pdf \ |
| -lib %l/latest/timing/*.lib \ |
| -gds %l/latest/cells/*/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ |
| rename=primitives filter=custom/scripts/inc_verilog.py \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -verilog %l/latest/cells/*/*.*.v \ |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ |
| compile-only filter=custom/scripts/inc_verilog.py \ |
| sort=custom/scripts/sort_pdkfiles.py \ |
| -library digital sky130_fd_sc_hd \ |
| -library digital sky130_fd_sc_hdll \ |
| -library digital sky130_fd_sc_hvl \ |
| -library digital sky130_fd_sc_hs \ |
| -library digital sky130_fd_sc_ls \ |
| -library digital sky130_fd_sc_ms \ |
| -library digital sky130_fd_sc_lp 2>&1 | tee -a ${SKY130A}_make.log |
| # Add a maskhint set for the tap cell .ag view to prevent problems writing |
| # when writing NSDM and PSDM to GDS during hierarchical adjustments. |
| ${ADDPROP} ${STAGING_PATH}/${SKY130A} sky130_fd_sc_hd sky130_fd_sc_hd__tapvpwrvgnd_1 \ |
| "MASKHINTS_PSDM 0 38 92 196" -mag |
| ${ADDPROP} ${STAGING_PATH}/${SKY130A} sky130_fd_sc_hd sky130_fd_sc_hd__tapvpwrvgnd_1 \ |
| "MASKHINTS_NSDM 0 280 92 506" -mag |
| # Add a maskhint to the HVL level shifter to represent the HVI layer as |
| # drawn in the GDS, and so eliminate the HVI-to-nwell DRC error. |
| ${ADDPROP} ${STAGING_PATH}/${SKY130A} sky130_fd_sc_hvl sky130_fd_sc_hvl__lsbufhv2lv_1 \ |
| "MASKHINTS_HVI 22 34 706 1316" -mag |
| # Remove the base verilog files which have already been included into |
| # the libraries |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${HD_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${HDLL_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${HVL_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${HS_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${MS_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${LS_VERILOG}/*.*.v |
| ${RM} ${STAGING_PATH}/${SKY130A}/libs.ref/${LP_VERILOG}/*.*.v |
| # Apply extra PDK patches until they get fixed properly in the source |
| patch -p1 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${HD_TECHLEF} \ |
| < custom/patches/hd_minenclosed.squeaky.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| patch -p1 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${HDLL_TECHLEF} \ |
| < custom/patches/hdll_minenclosed.squeaky.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| # Custom: Patch the HVL library to correct the resistor device names |
| patch -p3 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${HVL_SPICE} \ |
| < custom/patches/sky130_fd_pr_${HVL_PATCH4}.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| patch -p3 -f -d ${STAGING_PATH}/${SKY130A}/libs.ref/${HVL_CDL} \ |
| < custom/patches/sky130_fd_pr_6.patch \ |
| 2>&1 | tee -a ${SKY130A}_make.log || true |
| |
| alpha-a: |
| # Install alphanumeric library. |
| ${STAGE} -source ${ALPHA_PATH}/.. -target ${STAGING_PATH}/${SKY130A} \ |
| -mag %l/mag/*.mag filter=custom/scripts/text2m5.py \ |
| -library general sky130_ml_xx_hd 2>&1 | tee -a ${SKY130A}_make.log |
| # Install text2mag.py script for alphanumeric library |
| mkdir -p ${STAGING_PATH}/${SKY130A}/libs.ref/${MLXX_SCRIPTS} |
| cp custom/scripts/text2mag.py \ |
| ${STAGING_PATH}/${SKY130A}/libs.ref/${MLXX_SCRIPTS} |
| |
| sram-a: |
| # Install SRAM library. NOTE: SRAM macros share some of the same |
| # cell names, so use special option script gds_import_sram.tcl |
| # To do: Add option to process each GDS file individually in magic, |
| # instead of all at once. |
| ${STAGE} -source ${SRAM_PATH}/.. -target ${STAGING_PATH}/${SKY130A} \ |
| -lef %l/*/*.lef \ |
| -lib %l/*/*.lib \ |
| -gds %l/*/*.gds options=custom/scripts/gds_import_sram.tcl \ |
| -spice %l/*/*.lvs.sp filter=custom/scripts/sp_to_spice.py \ |
| -verilog %l/*/*.v \ |
| -library general sky130_sram_macros 2>&1 | tee -a ${SKY130A}_make.log |
| |
| osu-base-a: |
| # Install OSU digital standard cells. |
| ${STAGE} -source ${OSU_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef %l/tech/sky130_osu_sc.lef rename=sky130_osu_sc.tlef \ |
| -cdl %l/latest/cdl/*.cdl ignore=topography compile-only \ |
| -lef %l/latest/lef/*.lef compile-only \ |
| -lib %l/latest/lib/*.lib \ |
| -gds %l/latest/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc 2>&1 | tee -a ${SKY130A}_make.log |
| |
| osu-t12-a: |
| # Install OSU T12 hs digital standard cells. |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osc_sc_12t_hs.tlef \ |
| -spice 12T_hs/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 12T_hs/lef/*.lef \ |
| -lib 12T_hs/lib/*.lib \ |
| -gds 12T_hs/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_12t_hs 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T12 ms digital standard cells. |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osc_sc_12t_ms.tlef \ |
| -spice 12T_ms/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 12T_ms/lef/*.lef \ |
| -lib 12T_ms/lib/*.lib \ |
| -gds 12T_ms/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_12t_ms 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T12 ls digital standard cells. |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osc_sc_12t_ls.tlef \ |
| -spice 12T_ls/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 12T_ls/lef/*.lef \ |
| -lib 12T_ls/lib/*.lib \ |
| -gds 12T_ls/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_12t_ls 2>&1 | tee -a ${SKY130A}_make.log |
| |
| osu-t15-a: |
| # Install OSU T15 hs digital standard cells. |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osc_sc_15t_hs.tlef \ |
| -spice 15T_hs/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 15T_hs/lef/*.lef \ |
| -lib 15T_hs/lib/*.lib \ |
| -gds 15T_hs/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_15t_hs 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T15 ms digital standard cells. |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osc_sc_15t_ms.tlef \ |
| -spice 15T_ms/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 15T_ms/lef/*.lef \ |
| -lib 15T_ms/lib/*.lib \ |
| -gds 15T_ms/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_15t_ms 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T15 ls digital standard cells. |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osc_sc_15t_ls.tlef \ |
| -spice 15T_ls/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 15T_ls/lef/*.lef \ |
| -lib 15T_ls/lib/*.lib \ |
| -gds 15T_ls/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_15t_ls 2>&1 | tee -a ${SKY130A}_make.log |
| |
| osu-t18-a: |
| # Install OSU T18 hs digital standard cells. |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osc_sc_18t_hs.tlef \ |
| -spice 18T_hs/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 18T_hs/lef/*.lef \ |
| -lib 18T_hs/lib/*.lib \ |
| -gds 18T_hs/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_18t_hs 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T18 ms digital standard cells. |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osc_sc_18t_ms.tlef \ |
| -spice 18T_ms/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 18T_ms/lef/*.lef \ |
| -lib 18T_ms/lib/*.lib \ |
| -gds 18T_ms/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_18t_ms 2>&1 | tee -a ${SKY130A}_make.log |
| # Install OSU T18 ls digital standard cells. |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130A} \ |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osc_sc_18t_ls.tlef \ |
| -spice 18T_ls/cdl/*.spice compile-only exclude=*.*.spice \ |
| -lef 18T_ls/lef/*.lef \ |
| -lib 18T_ls/lib/*.lib \ |
| -gds 18T_ls/gds/*.gds compile-only \ |
| options=custom/scripts/gds_import_setup.tcl \ |
| -library digital sky130_osu_sc_18t_ls 2>&1 | tee -a ${SKY130A}_make.log |
| |
| install: install-a |
| |
| install-a: |
| echo "Starting SKY130 PDK migration on "`date` > ${SKY130A}_install.log |
| ${INSTALL} \ |
| -source ${STAGING_PATH}/${SKY130A} \ |
| -target ${SHARED_PDKS_PATH}/${SKY130A} \ |
| -variable PDKPATH \ |
| -link_from ${LINK_TARGETS} 2>&1 | tee -a ${SKY130A}_install.log |
| echo "Ended SKY130 PDK migration on "`date` >> ${SKY130A}_install.log |
| |
| uninstall: uninstall-a |
| |
| uninstall-a: |
| echo "Uninstalling SKY130 PDK from ${SHARED_PDKS_PATH}" |
| if test "x${SHARED_PDKS_PATH}" != "x" ; then \ |
| ${RM} -rf ${SHARED_PDKS_PATH}/${SKY130A} ; \ |
| fi |
| echo "Finished SKY130 PDK uninstall" |
| |
| clean: clean-a |
| |
| clean-a: |
| ${STAGE} -target ${STAGING_PATH}/${SKY130A} -clean |
| |
| veryclean: veryclean-a |
| |
| veryclean-a: clean-a |
| ${RM} ${SKY130A}_make.log |
| ${RM} ${SKY130A}_install.log |
| # Legacy name |
| ${RM} ${SKY130A}_migrate.log |
| |
| # Old aliases (retained for compatibility) |
| install-dist: |
| $(warning "'make install-dist' has been replaced with 'make install'") |
| make install |
| |
| install-local: |
| $(warning "'make install-local' has been replaced with 'make install'") |
| make install |
| |
| uninstall-dist: |
| $(warning "'make uninstall-dist' has been replaced with 'make uninstall'") |
| make uninstall |
| |
| uninstall-local: |
| $(warning "'make uninstall-local' has been replaced with 'make uninstall'") |
| make uninstall |
| |
| install-dist-a: |
| $(warning "'make install-dist-a' has been replaced with 'make install'") |
| make install |
| |
| install-local-a: |
| $(warning "'make install-local-a' has been replaced with 'make install'") |
| make install |
| |
| uninstall-dist-a: |
| $(warning "'make uninstall-dist-a' has been replaced with 'make uninstall'") |
| make uninstall |
| |
| uninstall-local-a: |
| $(warning "'make uninstall-local-a' has been replaced with 'make uninstall'") |
| make uninstall |