| # Makefile for efabless design kits for SkyWater Sky130: | |
| # | |
| # sky130A = 5-metal backend stack with dual MiM | |
| # sky130B = 5-metal backend stack with dual MiM and ReRAM | |
| # | |
| # Written by Tim Edwards March 2019 | |
| # efabless corporation | |
| # updated October 2019 | |
| # updated December 2019 (divide installation sections for individual tools) | |
| # updated March 2020 (refactored the install process) | |
| # updated May 2020 (changed to new process name Sky130) | |
| # updated January 2022 (divided into two variants A and B) | |
| # | |
| # Instructions: | |
| # | |
| # Run "configure" from the top level directory. Use the following | |
| # configuration options to match your environment: | |
| # | |
| # --enable-sky130-pdk[=<path>] | |
| # If enabled, install the skywater PDK. If <path> is specified, | |
| # then the skywater PDK is expected to be found rooted at the | |
| # given path. If not specified, then the skywater PDK will be | |
| # downloaded and installed to <repo root>/pdks. | |
| # If explicitly disabled, sky130 is skipped over entirely. | |
| # | |
| # --with-sky130-link-targets=<value> | |
| # where <value> is one of "none" or "source". If set to "source", | |
| # then where possible, the installed files are symbolic links | |
| # back to the source, rather than copies of the source. The | |
| # default value is "none" if the option is not specified. | |
| # | |
| # --with-ef-style | |
| # If specified, then the installation uses the efabless style, | |
| # which swaps the file hierarchy of file formats vs. IP libraries; | |
| # e.g., "gds/sky130_fd_sc_hd/" with ef-style, vs. | |
| # "sky130_fd_sc_hd/gds/" without it. | |
| # | |
| # Enable/disable for specific libraries to be installed (and downloaded if | |
| # needed). Libraries that are part of the open_pdks repository are enabled | |
| # by default and must be disabled by passing an option to configure. Libraries | |
| # that are not part of the open_pdks repository are disabled by default and | |
| # must be enabled by passing an option to configure. | |
| # | |
| # Internal libraries and tool setups that can be disabled are the following: | |
| # | |
| # --disable-magic | |
| # Do not install setup files for the magic layout tool. | |
| # | |
| # --disable-netgen | |
| # Do not install setup files for the netgen LVS tool. | |
| # | |
| # --disable-irsim | |
| # Do not install setup files for the IRSIM simulation tool. | |
| # | |
| # --disable-qflow | |
| # Do not install setup files for the qflow synthesis flow. | |
| # | |
| # --disable-openlane | |
| # Do not install setup files for the openlane sythesis flow. | |
| # | |
| # --disable-klayout | |
| # Do not install setup files for the klayout layout tool. | |
| # | |
| # | |
| # NOTE: The comments below are for features that have not yet been | |
| # implemented. | |
| # | |
| # External (third-party) libraries and tool setups are the following (enabled | |
| # by default): | |
| # | |
| # --enable-alpha-sky130[=<path>] | |
| # If enabled, install the sky130_ml_xx_hd font library from | |
| # Paul Schulz on github. If <path> is not specified, then the | |
| # font library will be cloned from the git repository and | |
| # installed. | |
| # | |
| # --enable-xschem-sky130[=<path>] | |
| # If enabled, install the Sky130 setup for the xschem schematic | |
| # editor. If <path> is specified, then the xschem setup is | |
| # expected to be found rooted at the given path. If not | |
| # specified, then the xschem setup will be cloned from the | |
| # repository and installed. | |
| # | |
| # --enable-klayout-sky130[=<path>] | |
| # If enabled, install the Sky130 setup for the klayout layout | |
| # editor. If <path> is specified, then the klayout setup is | |
| # expected to be found rooted at the given path. If not | |
| # specified, then the klayout setup will be cloned from the | |
| # repository and installed. | |
| # | |
| # External (third-party) libraries and tool setups are the following (disabled | |
| # by default): | |
| # | |
| # --enable-sram-sky130[=<path>] | |
| # If enabled, install the sky130_sram_macros library from | |
| # efabless on github. If <path> is not specified, then | |
| # the SRAM library will be cloned from the repository and | |
| # installed. | |
| # | |
| # --enable-osu-t12-sky130[=<path>] | |
| # If enabled, install the sky130_osu_sc_t12 libraries from | |
| # foss-eda-tools on googlesource. If <path> is not | |
| # specified, then the OSU standard cell library will be | |
| # clones from the repository and installed. | |
| # | |
| # --enable-osu-t15-sky130[=<path>] | |
| # If enabled, install the sky130_osu_sc_t15 libraries from | |
| # foss-eda-tools on googlesource. If <path> is not | |
| # specified, then the OSU standard cell library will be | |
| # clones from the repository and installed. | |
| # | |
| # --enable-osu-t18-sky130[=<path>] | |
| # If enabled, install the sky130_osu_sc_t18 libraries from | |
| # foss-eda-tools on googlesource. If <path> is not | |
| # specified, then the OSU standard cell library will be | |
| # clones from the repository and installed. | |
| # | |
| # The variables below are substituted from the configuration options: | |
| # | |
| # SKYWATER_PATH: Points to vendor sources | |
| # EF_STYLE: 1 for efabless style, 0 otherwise | |
| # LINK_TARGETS_A: If "source", link back to source when possible | |
| # ENABLED_VARIANTS: If not "all", then compile/install only the specified variants | |
| # | |
| # Run "make" to stage the PDK for tool setup and vendor libraries | |
| # | |
| # Run "make install" to install all staged files. | |
| # | |
| # Run "make clean" to remove all staging files. | |
| # | |
| # Run "make veryclean" to remove all staging and make.log files. | |
| # | |
| # For the sake of simplicity, the "standard" installation can be done | |
| # with the usual | |
| # | |
| # make | |
| # make install | |
| # make clean | |
| # | |
| #-------------------------------------------------------------------- | |
| # This Makefile contains bash-isms | |
| SHELL := /bin/bash | |
| export SHELL | |
| # We use pipes to save output to files, without pipefail they will always be | |
| # seen by make as having succeeded. | |
| SHELLOPTS := pipefail | |
| export SHELLOPTS | |
| MV = mv | |
| PATCH = patch | |
| SED = @SED@ | |
| prefix = @prefix@ | |
| datarootdir = @datarootdir@ | |
| datadir = @datadir@ | |
| # Use git revision if this is a cloned repo; otherwise get the revision | |
| # from the VERSION file in the directory above. | |
| GITREV = $(shell git describe --long) | |
| ifeq (${GITREV},) | |
| REVISION = $(shell cat ../VERSION) | |
| else | |
| REVISION = ${GITREV} | |
| endif | |
| TECH = sky130 | |
| # The run-time environment uses PDKPATH to override the PDK location, | |
| # so prevent that from happening during PDK install. This will also | |
| # happen with PDK_ROOT, so avoid that as well. | |
| unexport PDKPATH | |
| unexport PDK_ROOT | |
| # If EF_STYLE is set to 1, then efabless naming conventions are | |
| # used, otherwise the generic naming conventions are used. | |
| # Mainly, the hierarchy of library names and file types is reversed | |
| # (e.g., sky130_fd_sc_hd/lef vs. lef/sky130_fd_sc_hd). | |
| # EF_STYLE = 0 | 1 | |
| EF_STYLE = @EF_STYLE@ | |
| # Normally it's fine to keep the staging path in a local directory, | |
| # although /tmp or a dedicated staging area are also fine, as long | |
| # as the install process can write to the path. | |
| STAGING_PATH = $(shell pwd) | |
| SHARED_PDKS_PATH ?= $(datadir)/pdk | |
| # If LINK_TARGETS is set to "none", then files are copied | |
| # from the SkyWater sources to the target. If set to "source", | |
| # symbolic links are made in the target directories pointing | |
| # back to the SkyWater sources. If set to the name of another | |
| # PDK (e.g, "sky130A"), then symbolic links are made to the | |
| # same files in that PDK, where they exist, and are copied | |
| # from source, where they don't. | |
| # | |
| # Behavior is to let the link targets for variant A follow the | |
| # configuration option. Link targets for variant B will always | |
| # be the files of variant A (which may end up being symbolic | |
| # links to symbolic links if "source" was chosen for link-targets | |
| # in the configuration). | |
| # LINK_TARGETS = source | none | sky130A | |
| LINK_TARGETS_A = @SKY130_LINK_TARGETS@ | |
| LINK_TARGETS_B = sky130A | |
| # ENABLED_VARIANTS = all | A | B | |
| ENABLED_VARIANTS = @SKY130_ENABLED_VARIANTS@ | |
| ifeq (${ENABLED_VARIANTS},) | |
| VARIANTS += A B | |
| else | |
| ifeq (${ENABLED_VARIANTS}, all) | |
| VARIANTS += A B | |
| else | |
| VARIANTS += ${ENABLED_VARIANTS} | |
| endif | |
| endif | |
| # Paths: | |
| # Path to skywater_pdk | |
| SKYWATER_PATH = @SKY130_SOURCE_PATH@ | |
| ifneq ($(SKYWATER_PATH),) | |
| SKYWATER_LIBS_PATH = ${SKYWATER_PATH}/libraries | |
| else | |
| SKYWATER_LIBS_PATH = | |
| endif | |
| # Path to independent library sources (to be added to configuration options). | |
| ALPHA_PATH = @SKY130_ML_XX_HD_PATH@ | |
| XSCHEM_PATH = @XSCHEM_SKY130_PATH@ | |
| KLAYOUT_PATH = @KLAYOUT_SKY130_PATH@ | |
| PRECHECK_PATH = @PRECHECK_SKY130_PATH@ | |
| SRAM_PATH = @SKY130_SRAM_MACROS_PATH@ | |
| OSU_T12_PATH = @SKY130_OSU_T12_PATH@ | |
| OSU_T15_PATH = @SKY130_OSU_T15_PATH@ | |
| OSU_T18_PATH = @SKY130_OSU_T18_PATH@ | |
| PDK_URL = https://github.com/google/skywater-pdk | |
| ALPHA_URL = https://github.com/PaulSchulz/sky130_pschulz_xx_hd | |
| XSCHEM_URL = https://github.com/StefanSchippers/xschem_sky130 | |
| KLAYOUT_URL = https://github.com/mabrains/sky130_klayout_pdk | |
| PRECHECK_URL = https://github.com/efabless/mpw_precheck | |
| SRAM_URL = https://github.com/efabless/sky130_sram_macros | |
| OSU_T12_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t12 | |
| OSU_T15_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t15 | |
| OSU_T18_URL = https://foss-eda-tools.googlesource.com/skywater-pdk/libs/sky130_osu_sc_t18 | |
| # NOTE: Install destination is the git repository of the technology platform. | |
| # Once updated in git, the git project can be distributed to all hosts. | |
| # | |
| ifeq (${EF_STYLE}, 1) | |
| CONFIG_DIR = .ef-config | |
| REV_DIR = ${REVISION} | |
| else | |
| CONFIG_DIR = .config | |
| REV_DIR = . | |
| endif | |
| # EF process nodes created from the master sources | |
| SKY130A = sky130A | |
| SKY130B = sky130B | |
| DIST_LINK_TARGETS_A = ${LINK_TARGETS_A} | |
| DIST_LINK_TARGETS_B = ${SHARED_PDKS_PATH}/${LINK_TARGETS_B} | |
| # Basic definitions for each EF process node | |
| SKY130A_DEFS = -DTECHNAME=sky130A -DREVISION=${REVISION} | |
| SKY130B_DEFS = -DTECHNAME=sky130B -DREVISION=${REVISION} | |
| # Module definitions for each process node | |
| # (Note that MOS is default and therefore not used anywhere) | |
| SKY130A_DEFS += -DMETAL5 -DMIM -DREDISTRIBUTION | |
| SKY130B_DEFS += -DMETAL5 -DMIM -DREDISTRIBUTION | |
| # NOTE: ReRAM support is what distinguishes variant B from variant A. | |
| SKY130B_DEFS += -DRERAM | |
| # Add staging path | |
| SKY130A_DEFS += -DSTAGING_PATH=${STAGING_PATH} | |
| SKY130B_DEFS += -DSTAGING_PATH=${STAGING_PATH} | |
| # Get the timestamp of the open_pdks commit to use for stamping layouts. | |
| OPEN_PDKS_TIMESTAMP = $(shell git log -1 --format="%ad" --date=raw | cut -d' ' -f1) | |
| TIMESTAMP_OPT = -timestamp ${OPEN_PDKS_TIMESTAMP} | |
| # Record commit numbers for the nodeinfo.json file | |
| OPEN_PDKS_COMMIT = $(shell git rev-parse HEAD) | |
| ifeq (${OPEN_PDKS_COMMIT},) | |
| COMMIT_DEFS = -DOPEN_PDKS_COMMIT=${REVISION} | |
| else | |
| COMMIT_DEFS = -DOPEN_PDKS_COMMIT=${OPEN_PDKS_COMMIT} | |
| endif | |
| ifeq (${XSCHEM_PATH},) | |
| COMMIT_DEFS += -DXSCHEM_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DXSCHEM_COMMIT=$(shell cd ${XSCHEM_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${KLAYOUT_PATH},) | |
| COMMIT_DEFS += -DKLAYOUT_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DKLAYOUT_COMMIT=$(shell cd ${KLAYOUT_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${PRECHECK_PATH},) | |
| COMMIT_DEFS += -DPRECHECK_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DPRECHECK_COMMIT=$(shell cd ${PRECHECK_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${ALPHA_PATH},) | |
| COMMIT_DEFS += -DALPHA_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DALPHA_COMMIT=$(shell cd ${ALPHA_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${SRAM_PATH},) | |
| COMMIT_DEFS += -DSRAM_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DSRAM_COMMIT=$(shell cd ${SRAM_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${OSU_T12_PATH},) | |
| COMMIT_DEFS += -DOSU_T12_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DOSU_T12_COMMIT=$(shell cd ${OSU_T12_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${OSU_T15_PATH},) | |
| COMMIT_DEFS += -DOSU_T15_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DOSU_T15_COMMIT=$(shell cd ${OSU_T15_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${OSU_T18_PATH},) | |
| COMMIT_DEFS += -DOSU_T18_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DOSU_T18_COMMIT=$(shell cd ${OSU_T18_PATH} ; git rev-parse HEAD) | |
| endif | |
| ifeq (${SKYWATER_PATH},) | |
| COMMIT_DEFS += -DFD_PR_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_IO_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_HD_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_HDLL_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_HVL_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_HS_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_MS_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_LS_COMMIT="unknown" | |
| COMMIT_DEFS += -DFD_SC_LP_COMMIT="unknown" | |
| else | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_pr/latest/cells),) | |
| COMMIT_DEFS += -DFD_PR_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_PR_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_pr/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_io/latest/cells),) | |
| COMMIT_DEFS += -DFD_IO_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_IO_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_io/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_hd/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_HD_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_HD_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hd/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_hdll/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_HDLL_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_HDLL_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hdll/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_hvl/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_HVL_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_HVL_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hvl/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_hs/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_HS_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_HS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_hs/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_ms/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_MS_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_MS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_ms/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_ls/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_LS_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_LS_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_ls/latest) | |
| endif | |
| ifeq ($(wildcard ${SKYWATER_PATH}/libraries/sky130_fd_sc_lp/latest/cells),) | |
| COMMIT_DEFS += -DFD_SC_LP_COMMIT="unknown" | |
| else | |
| COMMIT_DEFS += -DFD_SC_LP_COMMIT=$(shell cd ${SKYWATER_PATH} ; git rev-parse @:libraries/sky130_fd_sc_lp/latest) | |
| endif | |
| endif | |
| COMMIT_DEFS += -DMAGIC_COMMIT=$(shell magic -dnull -noconsole --commit) | |
| COMMIT_DEFS += -DMAGIC_VERSION=$(shell magic -dnull -noconsole --version) | |
| COMMIT_DEFS += -DOPEN_PDKS_VERSION=$(shell cat ../VERSION) | |
| ifeq (${EF_STYLE}, 1) | |
| EF_FORMAT = -ef_format | |
| SKY130A_DEFS += -DEF_FORMAT | |
| SKY130B_DEFS += -DEF_FORMAT | |
| else | |
| EF_FORMAT = -std_format | |
| endif | |
| MAGICTOP = libs.tech/magic | |
| NETGENTOP = libs.tech/netgen | |
| IRSIMTOP = libs.tech/irsim | |
| QFLOWTOP = libs.tech/qflow | |
| KLAYOUTTOP = libs.tech/klayout | |
| OPENLANETOP = libs.tech/openlane | |
| XSCHEMTOP = libs.tech/xschem | |
| XCIRCUITTOP = libs.tech/xcircuit | |
| NGSPICETOP = libs.tech/ngspice | |
| ifeq (${EF_STYLE}, 1) | |
| MAGICPATH = ${MAGICTOP}/${REVISION} | |
| MAGICCURRENT = ${MAGICTOP}/current | |
| else | |
| MAGICPATH = ${MAGICTOP} | |
| MAGICCURRENT = ${MAGICTOP} | |
| endif | |
| # Currently, netgen, qflow, irsim, and klayout do not use revisioning (needs to change!) | |
| NETGENPATH = ${NETGENTOP} | |
| IRSIMPATH = ${IRSIMTOP} | |
| QFLOWPATH = ${QFLOWTOP} | |
| KLAYOUTPATH = ${KLAYOUTTOP} | |
| OPENLANEPATH = ${OPENLANETOP} | |
| XSCHEMPATH = ${XSCHEMTOP} | |
| XCIRCUITPATH = ${XCIRCUITTOP} | |
| NGSPICEPATH = ${NGSPICETOP} | |
| MAGICTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${MAGICTOP} | |
| NETGENTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NETGENTOP} | |
| IRSIMTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${IRSIMTOP} | |
| QFLOWTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${QFLOWTOP} | |
| KLAYOUTTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${KLAYOUTTOP} | |
| OPENLANETOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${OPENLANETOP} | |
| XSCHEMTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XSCHEMTOP} | |
| XCIRCUITTOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XCIRCUITTOP} | |
| NGSPICETOP_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NGSPICETOP} | |
| MAGIC_STAGING_A = ${STAGING_PATH}/${SKY130A}/${MAGICPATH} | |
| NETGEN_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NETGENPATH} | |
| IRSIM_STAGING_A = ${STAGING_PATH}/${SKY130A}/${IRSIMPATH} | |
| QFLOW_STAGING_A = ${STAGING_PATH}/${SKY130A}/${QFLOWPATH} | |
| KLAYOUT_STAGING_A = ${STAGING_PATH}/${SKY130A}/${KLAYOUTPATH} | |
| OPENLANE_STAGING_A = ${STAGING_PATH}/${SKY130A}/${OPENLANEPATH} | |
| XSCHEM_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XSCHEMPATH} | |
| XCIRCUIT_STAGING_A = ${STAGING_PATH}/${SKY130A}/${XCIRCUITPATH} | |
| NGSPICE_STAGING_A = ${STAGING_PATH}/${SKY130A}/${NGSPICEPATH} | |
| MAGICTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${MAGICTOP} | |
| NETGENTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${NETGENTOP} | |
| IRSIMTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${IRSIMTOP} | |
| QFLOWTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${QFLOWTOP} | |
| KLAYOUTTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${KLAYOUTTOP} | |
| OPENLANETOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${OPENLANETOP} | |
| XSCHEMTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${XSCHEMTOP} | |
| XCIRCUITTOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${XCIRCUITTOP} | |
| NGSPICETOP_STAGING_B = ${STAGING_PATH}/${SKY130B}/${NGSPICETOP} | |
| MAGIC_STAGING_B = ${STAGING_PATH}/${SKY130B}/${MAGICPATH} | |
| NETGEN_STAGING_B = ${STAGING_PATH}/${SKY130B}/${NETGENPATH} | |
| IRSIM_STAGING_B = ${STAGING_PATH}/${SKY130B}/${IRSIMPATH} | |
| QFLOW_STAGING_B = ${STAGING_PATH}/${SKY130B}/${QFLOWPATH} | |
| KLAYOUT_STAGING_B = ${STAGING_PATH}/${SKY130B}/${KLAYOUTPATH} | |
| OPENLANE_STAGING_B = ${STAGING_PATH}/${SKY130B}/${OPENLANEPATH} | |
| XSCHEM_STAGING_B = ${STAGING_PATH}/${SKY130B}/${XSCHEMPATH} | |
| XCIRCUIT_STAGING_B = ${STAGING_PATH}/${SKY130B}/${XCIRCUITPATH} | |
| NGSPICE_STAGING_B = ${STAGING_PATH}/${SKY130B}/${NGSPICEPATH} | |
| SKY130A_DEFS += -DMAGIC_CURRENT=${MAGICCURRENT} | |
| SKY130B_DEFS += -DMAGIC_CURRENT=${MAGICCURRENT} | |
| # Openlane has a number of files that are common to all digital | |
| # standard cell libraries, so these are collected in one definition | |
| # here: | |
| OPENLANE_COMMON = config.tcl tracks.info no_synth.cells drc_exclude.cells | |
| OPENLANE_COMMON += tribuff_map.v latch_map.v mux2_map.v mux4_map.v fa_map.v rca_map.v csa_map.v | |
| # Corners defined in IRSIM parameter files (wild-carded) | |
| IRSIM_CORNERS = `ls irsim/*.prm | cut -c14-` | |
| # Where cpp syntax is followed, this is equivalent to cpp, but it does not | |
| # mangle non-C source files under the belief that they are actually C code. | |
| CPP = ../common/preproc.py | |
| # The following script in the ../common directory does most of the work of | |
| # copying or linking the foundry vendor files to the target directory. | |
| STAGE = set -f ; ../common/foundry_install.py ${EF_FORMAT} ${TIMESTAMP_OPT} | |
| ifneq ($(DESTDIR), ) | |
| INSTALL = ../common/staging_install.py -writeto $(DESTDIR) ${EF_FORMAT} | |
| else | |
| INSTALL = ../common/staging_install.py ${EF_FORMAT} | |
| endif | |
| # The script(s) below are used for custom changes to the vendor PDK files | |
| ADDPROP = ../common/insert_property.py ${EF_FORMAT} | |
| ADDLAYER = ../common/insert_layer.py ${EF_FORMAT} | |
| # List the EDA tools to install local setup files for | |
| TOOLS = | |
| # KLAYOUT_DISABLED = 0 | 1 | |
| KLAYOUT_DISABLED = @KLAYOUT_DISABLED@ | |
| ifneq (${KLAYOUT_DISABLED}, 1) | |
| TOOLS += klayout | |
| endif | |
| # OPENLANE_DISABLED = 0 | 1 | |
| OPENLANE_DISABLED = @OPENLANE_DISABLED@ | |
| ifneq (${OPENLANE_DISABLED}, 1) | |
| TOOLS += openlane | |
| endif | |
| # QFLOW_DISABLED = 0 | 1 | |
| QFLOW_DISABLED = @QFLOW_DISABLED@ | |
| ifneq (${QFLOW_DISABLED}, 1) | |
| TOOLS += qflow | |
| endif | |
| # MAGIC_DISABLED = 0 | 1 | |
| MAGIC_DISABLED = @MAGIC_DISABLED@ | |
| ifneq (${MAGIC_DISABLED}, 1) | |
| TOOLS += magic | |
| endif | |
| # NETGEN_DISABLED = 0 | 1 | |
| NETGEN_DISABLED = @NETGEN_DISABLED@ | |
| ifneq (${NETGEN_DISABLED}, 1) | |
| TOOLS += netgen | |
| endif | |
| # IRSIM_DISABLED = 0 | 1 | |
| IRSIM_DISABLED = @IRSIM_DISABLED@ | |
| ifneq (${IRSIM_DISABLED}, 1) | |
| TOOLS += irsim | |
| endif | |
| # XSCHEM_DISABLED = 0 | 1 | |
| XSCHEM_DISABLED = @XSCHEM_DISABLED@ | |
| ifneq (${XSCHEM_DISABLED}, 1) | |
| TOOLS += xschem | |
| endif | |
| # XCIRCUIT_DISABLED = 0 | 1 | |
| XCIRCUIT_DISABLED = @XCIRCUIT_DISABLED@ | |
| ifneq (${XCIRCUIT_DISABLED}, 1) | |
| TOOLS += xcircuit | |
| endif | |
| # These definitions depend on the setting of EF_STYLE | |
| ifeq (${EF_STYLE}, 1) | |
| IO_VERILOG = verilog/sky130_fd_io | |
| IO_GDS = gds/sky130_fd_io | |
| HD_VERILOG = verilog/sky130_fd_sc_hd | |
| HDLL_VERILOG = verilog/sky130_fd_sc_hdll | |
| HVL_VERILOG = verilog/sky130_fd_sc_hvl | |
| HS_VERILOG = verilog/sky130_fd_sc_hs | |
| MS_VERILOG = verilog/sky130_fd_sc_ms | |
| LS_VERILOG = verilog/sky130_fd_sc_ls | |
| LP_VERILOG = verilog/sky130_fd_sc_lp | |
| HD_TECHLEF = techLEF/sky130_fd_sc_hd | |
| HDLL_TECHLEF = techLEF/sky130_fd_sc_hdll | |
| MLXX_SCRIPTS = scripts/sky130_ml_xx_hd | |
| PR_SPICE = spi/sky130_fd_pr | |
| HVL_SPICE = spi/sky130_fd_sc_hvl | |
| HD_SPICE = spi/sky130_fd_sc_hd | |
| HVL_PATCH4 = 4b | |
| HVL_CDL = cdl/sky130_fd_sc_hvl | |
| SPIEXT = spi | |
| else | |
| IO_VERILOG = sky130_fd_io/verilog | |
| IO_GDS = sky130_fd_io/gds | |
| HD_VERILOG = sky130_fd_sc_hd/verilog | |
| HDLL_VERILOG = sky130_fd_sc_hdll/verilog | |
| HVL_VERILOG = sky130_fd_sc_hvl/verilog | |
| HS_VERILOG = sky130_fd_sc_hs/verilog | |
| MS_VERILOG = sky130_fd_sc_ms/verilog | |
| LS_VERILOG = sky130_fd_sc_ls/verilog | |
| LP_VERILOG = sky130_fd_sc_lp/verilog | |
| HD_TECHLEF = sky130_fd_sc_hd/techlef | |
| HDLL_TECHLEF = sky130_fd_sc_hdll/techlef | |
| MLXX_SCRIPTS = sky130_ml_xx_hd/scripts | |
| PR_SPICE = sky130_fd_pr/spice | |
| HVL_SPICE = sky130_fd_sc_hvl/spice | |
| HD_SPICE = sky130_fd_sc_hd/spice | |
| HVL_PATCH4 = 4 | |
| HVL_CDL = sky130_fd_sc_hvl/cdl | |
| SPIEXT = spice | |
| endif | |
| reference: ${TECH}.json | |
| # Rewrite the ${TECH}.json file to change the commit values in | |
| # "reference" to reflect the state of the system when "make | |
| # reference" was run. This is then committed to the open_pdks | |
| # repository to create a known reference configuration of all | |
| # tools. | |
| ../common/save_commit_refs.py ${COMMIT_DEFS} ${TECH}.json | |
| all: $(foreach var, ${VARIANTS}, all-$(var)) | |
| # Handle prerequisites (fetch and install the PDK and requested libraries) | |
| prerequisites: pdk-repo alpha-repo xschem-repo klayout-repo precheck-repo sram-repo osu-t12-repo osu-t15-repo osu-t18-repo | |
| pdk-repo: | |
| if test "x${SKYWATER_PATH}" != "x" ; then \ | |
| if test -d "${SKYWATER_PATH}" ; then \ | |
| echo "Using existing installation of SkyWater PDK from ${SKYWATER_PATH}" ; \ | |
| else \ | |
| echo "Downloading SkyWater PDK from ${PDK_URL}" ; \ | |
| custom/scripts/pdk_download.sh ${PDK_URL} ${SKYWATER_PATH} ; \ | |
| fi ; \ | |
| fi | |
| alpha-repo: | |
| if test "x${ALPHA_PATH}" != "x" ; then \ | |
| if test -d "${ALPHA_PATH}" ; then \ | |
| echo "Using existing installation of alphanumeric library from ${ALPHA_PATH}" ; \ | |
| else \ | |
| echo "Downloading alphanumeric library from ${ALPHA_URL}" ; \ | |
| ../scripts/download.sh ${ALPHA_URL} ${ALPHA_PATH} ; \ | |
| fi ; \ | |
| fi | |
| sram-repo: | |
| if test "x${SRAM_PATH}" != "x" ; then \ | |
| if test -d "${SRAM_PATH}" ; then \ | |
| echo "Using existing installation of SRAM macro library from ${SRAM_PATH}" ; \ | |
| else \ | |
| echo "Downloading SRAM macro library from ${SRAM_URL}" ; \ | |
| ../scripts/download.sh ${SRAM_URL} ${SRAM_PATH} ; \ | |
| fi ; \ | |
| fi | |
| xschem-repo: | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| if test -d "${XSCHEM_PATH}" ; then \ | |
| echo "Using existing installation of xschem setup from ${XSCHEM_PATH}" ; \ | |
| else \ | |
| echo "Downloading xschem setup from ${XSCHEM_URL}" ; \ | |
| ../scripts/download.sh ${XSCHEM_URL} ${XSCHEM_PATH} ; \ | |
| fi ; \ | |
| fi | |
| klayout-repo: | |
| if test "x${KLAYOUT_PATH}" != "x" ; then \ | |
| if test -d "${KLAYOUT_PATH}" ; then \ | |
| echo "Using existing installation of klayout setup from ${KLAYOUT_PATH}" ; \ | |
| else \ | |
| echo "Downloading klayout setup from ${KLAYOUT_URL}" ; \ | |
| ../scripts/download.sh ${KLAYOUT_URL} ${KLAYOUT_PATH} ; \ | |
| fi ; \ | |
| fi | |
| precheck-repo: | |
| if test "x${PRECHECK_PATH}" != "x" ; then \ | |
| if test -d "${PRECHECK_PATH}" ; then \ | |
| echo "Using existing installation of klayout setup from ${PRECHECK_PATH}" ; \ | |
| else \ | |
| echo "Downloading klayout setup from ${PRECHECK_URL}" ; \ | |
| ../scripts/download.sh ${PRECHECK_URL} ${PRECHECK_PATH} ; \ | |
| fi ; \ | |
| fi | |
| osu-t12-repo: | |
| if test "x${OSU_T12_PATH}" != "x" ; then \ | |
| if test -d "${OSU_T12_PATH}" ; then \ | |
| echo "Using existing installation of OSU T12 standard cell library from ${OSU_T12_PATH}" ; \ | |
| else \ | |
| echo "Downloading OSU standard T12 cell library from ${OSU_T12_URL}" ; \ | |
| ../scripts/download.sh ${OSU_T12_URL} ${OSU_T12_PATH} 0 ; \ | |
| fi ; \ | |
| fi | |
| osu-t15-repo: | |
| if test "x${OSU_T15_PATH}" != "x" ; then \ | |
| if test -d "${OSU_T15_PATH}" ; then \ | |
| echo "Using existing installation of OSU T15 standard cell library from ${OSU_T15_PATH}" ; \ | |
| else \ | |
| echo "Downloading OSU standard T15 cell library from ${OSU_T15_URL}" ; \ | |
| ../scripts/download.sh ${OSU_T15_URL} ${OSU_T15_PATH} 0 ; \ | |
| fi ; \ | |
| fi | |
| osu-t18-repo: | |
| if test "x${OSU_T18_PATH}" != "x" ; then \ | |
| if test -d "${OSU_T18_PATH}" ; then \ | |
| echo "Using existing installation of OSU T18 standard cell library from ${OSU_T18_PATH}" ; \ | |
| else \ | |
| echo "Downloading OSU standard T18 cell library from ${OSU_T18_URL}" ; \ | |
| ../scripts/download.sh ${OSU_T18_URL} ${OSU_T18_PATH} 0 ; \ | |
| fi ; \ | |
| fi | |
| # Update prerequisites | |
| update: update-pdk-repo update-alpha-repo update-xschem-repo update-klayout-repo update-precheck-repo update-sram-repo update-osu-t12-repo update-osu-t15-repo update-osu-t18-repo | |
| update-pdk-repo: | |
| if test "x${SKYWATER_PATH}" != "x" ; then \ | |
| echo "Updating SkyWater PDK from ${PDK_URL}" ; \ | |
| custom/scripts/pdk_update.sh ${SKYWATER_PATH} ; \ | |
| fi | |
| update-alpha-repo: | |
| if test "x${ALPHA_PATH}" != "x" ; then \ | |
| echo "Updating alphanumeric library from ${ALPHA_URL}" ; \ | |
| ../scripts/update.sh ${ALPHA_PATH} ; \ | |
| fi | |
| update-sram-repo: | |
| if test "x${SRAM_PATH}" != "x" ; then \ | |
| echo "Updating SRAM macro library from ${SRAM_URL}" ; \ | |
| ../scripts/update.sh ${SRAM_PATH} ; \ | |
| fi | |
| update-xschem-repo: | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| echo "Updating xschem setup from ${XSCHEM_URL}" ; \ | |
| ../scripts/update.sh ${XSCHEM_PATH} ; \ | |
| fi | |
| update-klayout-repo: | |
| if test "x${KLAYOUT_PATH}" != "x" ; then \ | |
| echo "Updating klayout setup from ${KLAYOUT_URL}" ; \ | |
| ../scripts/update.sh ${KLAYOUT_PATH} ; \ | |
| fi | |
| update-precheck-repo: | |
| if test "x${PRECHECK_PATH}" != "x" ; then \ | |
| echo "Updating klayout setup from ${PRECHECK_URL}" ; \ | |
| ../scripts/update.sh ${PRECHECK_PATH} ; \ | |
| fi | |
| update-osu-t12-repo: | |
| if test "x${OSU_T12_PATH}" != "x" ; then \ | |
| echo "Updating OSU standard T12 cell library from ${OSU_T12_URL}" ; \ | |
| ../scripts/update.sh ${OSU_T12_PATH} ; \ | |
| fi | |
| update-osu-t15-repo: | |
| if test "x${OSU_T15_PATH}" != "x" ; then \ | |
| echo "Updating OSU standard T15 cell library from ${OSU_T15_URL}" ; \ | |
| ../scripts/update.sh ${OSU_T15_PATH} ; \ | |
| fi | |
| update-osu-t18-repo: | |
| if test "x${OSU_T18_PATH}" != "x" ; then \ | |
| echo "Updating OSU standard T18 cell library from ${OSU_T18_URL}" ; \ | |
| ../scripts/update.sh ${OSU_T18_PATH} ; \ | |
| fi | |
| all-%: prerequisites | |
| echo "Starting sky130$* PDK staging on "`date` > ${SKY130$*}_make.log | |
| ${MAKE} general-$* | |
| ${MAKE} tools-$* | |
| ${MAKE} vendor-$* | |
| echo "Ended sky130$* PDK staging on "`date` >> ${SKY130$*}_make.log | |
| general-%: ${TECH}.json | |
| mkdir -p ${STAGING_PATH}/${SKY130$*}/${CONFIG_DIR} | |
| rm -f ${STAGING_PATH}/${SKY130$*}/${CONFIG_DIR}/nodeinfo.json | |
| ${CPP} ${SKY130$*_DEFS} ${COMMIT_DEFS} ${TECH}.json \ | |
| ${STAGING_PATH}/${SKY130$*}/${CONFIG_DIR}/nodeinfo.json | |
| tools-A: $(addsuffix -A, $(TOOLS)) | |
| tools-B: $(addsuffix -B, $(TOOLS)) | |
| magic-%: magic/${TECH}.tech magic/${TECH}gds.tech magic/${TECH}.magicrc magic/${TECH}.tcl | |
| mkdir -p ${MAGICTOP_STAGING_$*} | |
| mkdir -p ${MAGIC_STAGING_$*} | |
| rm -f ${MAGICTOP_STAGING_$*}/current | |
| rm -f ${MAGIC_STAGING_$*}/${SKY130$*}.tech | |
| rm -f ${MAGIC_STAGING_$*}/${SKY130$*}-GDS.tech | |
| rm -f ${MAGIC_STAGING_$*}/${SKY130$*}.tcl | |
| rm -f ${MAGIC_STAGING_$*}/${SKY130$*}-BindKeys | |
| rm -f ${MAGIC_STAGING_$*}/magicrc | |
| if test "${EF_STYLE}" == "1" ; then \ | |
| (cd ${MAGICTOP_STAGING_$*} ; ln -s ${REV_DIR} current) ; \ | |
| fi | |
| cp -rp custom/scripts/seal_ring_generator ${MAGIC_STAGING_$*}/. | |
| cp -rp custom/scripts/bump_bond_generator ${MAGIC_STAGING_$*}/. | |
| cp custom/scripts/run_standard_drc.py ${MAGIC_STAGING_$*}/. | |
| ${CPP} ${SKY130$*_DEFS} custom/scripts/generate_fill.py \ | |
| ${MAGIC_STAGING_$*}/generate_fill.py | |
| ${CPP} ${SKY130$*_DEFS} custom/scripts/check_density.py \ | |
| ${MAGIC_STAGING_$*}/check_density.py | |
| ${CPP} ${SKY130$*_DEFS} custom/scripts/check_antenna.py \ | |
| ${MAGIC_STAGING_$*}/check_antenna.py | |
| ${CPP} ${SKY130$*_DEFS} magic/${TECH}.tech ${MAGIC_STAGING_$*}/${SKY130$*}.tech | |
| ${CPP} ${SKY130$*_DEFS} magic/${TECH}gds.tech ${MAGIC_STAGING_$*}/${SKY130$*}-GDS.tech | |
| ${CPP} ${SKY130$*_DEFS} magic/${TECH}.magicrc ${MAGIC_STAGING_$*}/${SKY130$*}.magicrc | |
| ${CPP} ${SKY130$*_DEFS} ../common/pdk.bindkeys ${MAGIC_STAGING_$*}/${SKY130$*}-BindKeys | |
| ${CPP} ${SKY130$*_DEFS} magic/${TECH}.tcl ${MAGIC_STAGING_$*}/${SKY130$*}.tcl | |
| ${CPP} ${SKY130$*_DEFS} ../common/pdk.tcl >> ${MAGIC_STAGING_$*}/${SKY130$*}.tcl | |
| qflow-%: qflow/${TECH}.sh qflow/${TECH}.par | |
| mkdir -p ${QFLOWTOP_STAGING_$*} | |
| mkdir -p ${QFLOW_STAGING_$*} | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hd.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hd.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hdll.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hdll.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hs.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hs.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hvl.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_hvl.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_ls.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_ls.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_lp.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_lp.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_ms.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_fd_sc_ms.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ls.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ls.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ms.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ms.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_hs.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_hs.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ls.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ls.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ms.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ms.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_hs.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_hs.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ls.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ls.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ms.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ms.par | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_hs.sh | |
| rm -f ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_hs.par | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_hd -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_hd.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_hdll -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_hdll.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_hvl -DVOLTAGE=4v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_hvl.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_hs -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_hs.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_lp -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_lp.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_ls -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_ls.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_fd_sc_ms -DVOLTAGE=1v95 \ | |
| qflow/${TECH}.sh ${QFLOW_STAGING_$*}/sky130_fd_sc_ms.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_12t_ls qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ls.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_12t_ms qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ms.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_12t_hs qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_hs.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_15t_ls qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ls.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_15t_ms qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ms.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_15t_hs qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_hs.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_18t_ls qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ls.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_18t_ms qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ms.sh | |
| ${CPP} ${SKY130$*_DEFS} -DLIBRARY=sky130_osu_sc_18t_hs qflow/sky130osu.sh \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_hs.sh | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_hd.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_hdll.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_hvl.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_hs.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_ms.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_lp.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par ${QFLOW_STAGING_$*}/sky130_fd_sc_ls.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ls.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_ms.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_12t_hs.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ls.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_ms.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_15t_hs.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ls.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_ms.par | |
| ${CPP} ${SKY130$*_DEFS} qflow/${TECH}.par \ | |
| ${QFLOW_STAGING_$*}/sky130_osu_sc_18t_hs.par | |
| netgen-%: netgen/${TECH}_setup.tcl | |
| mkdir -p ${NETGENTOP_STAGING_$*} | |
| mkdir -p ${NETGEN_STAGING_$*} | |
| rm -f ${NETGEN_STAGING_$*}/${SKY130$*}_setup.tcl | |
| rm -f ${NETGEN_STAGING_$*}/setup.tcl | |
| ${CPP} ${SKY130$*_DEFS} netgen/${TECH}_setup.tcl \ | |
| ${NETGEN_STAGING_$*}/${SKY130$*}_setup.tcl | |
| (cd ${NETGEN_STAGING_$*} ; ln -s ${SKY130$*}_setup.tcl setup.tcl) | |
| irsim-%: irsim | |
| mkdir -p ${IRSIMTOP_STAGING_$*} | |
| mkdir -p ${IRSIM_STAGING_$*} | |
| rm -f ${IRSIM_STAGING_$*}/${SKY130$*}_*.prm | |
| for corner in ${IRSIM_CORNERS} ; do \ | |
| cat irsim/header.txt irsim/sky130_$$corner > \ | |
| ${IRSIM_STAGING_$*}/${SKY130$*}_$$corner ; \ | |
| done | |
| xcircuit-%: xcircuit/${TECH}.xcircuitrc | |
| rm -rf ${XCIRCUIT_STAGING_$*} | |
| mkdir -p ${XCIRCUITTOP_STAGING_$*} | |
| mkdir -p ${XCIRCUIT_STAGING_$*} | |
| rm -f ${XCIRCUIT_STAGING_$*}/*.lps | |
| rm -f ${XCIRCUIT_STAGING_$*}/${SKY130$*}.xcircuitrc | |
| ${CPP} ${SKY130$*_DEFS} xcircuit/ngspice.lps ${XCIRCUIT_STAGING_$*}/ngspice.lps | |
| ${CPP} ${SKY130$*_DEFS} xcircuit/sky130_fd_pr.lps \ | |
| ${XCIRCUIT_STAGING_$*}/sky130_fd_pr.lps | |
| ${CPP} ${SKY130$*_DEFS} -DHD_SPICE=${HD_SPICE} -DSPIEXT=${SPIEXT} \ | |
| xcircuit/sky130_fd_sc_hd.lps ${XCIRCUIT_STAGING_$*}/sky130_fd_sc_hd.lps | |
| ${CPP} ${SKY130$*_DEFS} xcircuit/${TECH}.xcircuitrc \ | |
| ${XCIRCUIT_STAGING_$*}/${SKY130$*}.xcircuitrc | |
| klayout-%: ${KLAYOUT_PATH} | |
| if test "x${KLAYOUT_PATH}" != "x" ; then \ | |
| rm -rf ${KLAYOUT_STAGING_$*} ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*} ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*}/tech ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*}/drc ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*}/lvs ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*}/scripts ; \ | |
| mkdir -p ${KLAYOUT_STAGING_$*}/pymacros ; \ | |
| fi | |
| # Copy lvs and pymacro directories from the repository. Other files | |
| # are rearranged to the preferred structure. | |
| if test "x${KLAYOUT_PATH}" != "x" ; then \ | |
| cp -rp ${KLAYOUT_PATH}/sky130_tech/tech/sky130/lvs/* ${KLAYOUT_STAGING_$*}/lvs/ ; \ | |
| cp -rp ${KLAYOUT_PATH}/sky130_tech/tech/sky130/pymacros/* ${KLAYOUT_STAGING_$*}/pymacros/ ; \ | |
| cp ${KLAYOUT_PATH}/sky130_tech/tech/sky130/${TECH}.lyp ${KLAYOUT_STAGING_$*}/tech/${SKY130$*}.lyp ; \ | |
| cp ${KLAYOUT_PATH}/sky130_tech/tech/sky130/${TECH}.lyt ${KLAYOUT_STAGING_$*}/tech/${SKY130$*}.lyt ; \ | |
| cp -rp ${KLAYOUT_PATH}/scripts/* ${KLAYOUT_STAGING_$*}/scripts/ ; \ | |
| fi | |
| # Copy original DRC deck from open_pdks (is this useful?) | |
| cp klayout/sky130.lydrc ${KLAYOUT_STAGING_$*}/drc/${SKY130$*}.lydrc | |
| # Copy drc directory contents from the Efabless Open MPW precheck repository | |
| if test "x${PRECHECK_PATH}" != "x" ; then \ | |
| cp ${PRECHECK_PATH}/checks/tech-files/sky130A_mr.drc ${KLAYOUT_STAGING_$*}/drc/${SKY130$*}_mr.drc ; \ | |
| cp -rp ${PRECHECK_PATH}/checks/drc_checks/klayout/* ${KLAYOUT_STAGING_$*}/drc/ ; \ | |
| fi | |
| xschem-%: ${XSCHEM_PATH} | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| rm -rf ${XSCHEM_STAGING_$*} ; \ | |
| mkdir -p ${XSCHEMTOP_STAGING_$*} ; \ | |
| mkdir -p ${XSCHEM_STAGING_$*} ; \ | |
| fi | |
| # Copy the entire repository (other than .git, if it exists) | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| cp -rp ${XSCHEM_PATH}/* ${XSCHEM_STAGING_$*} ; \ | |
| fi | |
| # xschem setup is for sky130A. Fix for the given target variant. | |
| # Add custom additions to the startup file for open_pdk. | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| cat ${XSCHEM_PATH}/xschemrc | \ | |
| ${SED} -e "/sky130A/s#sky130A#TECHNAME#" \ | |
| > ${XSCHEM_STAGING_$*}/xschemrc_source ; \ | |
| ${CPP} ${SKY130$*_DEFS} ${XSCHEM_STAGING_$*}/xschemrc_source \ | |
| ${XSCHEM_STAGING_$*}/xschemrc ; \ | |
| cat ${XSCHEM_PATH}/xschem_verilog_import/xschemrc | \ | |
| ${SED} -e "/sky130A/s#sky130A#TECHNAME#" \ | |
| > ${XSCHEM_STAGING_$*}/xschemrc_source ; \ | |
| ${CPP} ${SKY130$*_DEFS} ${XSCHEM_STAGING_$*}/xschemrc_source \ | |
| ${XSCHEM_STAGING_$*}/xschem_verilog_import/xschemrc ; \ | |
| rm -f ${XSCHEM_STAGING_$*}/xschemrc_source ; \ | |
| cat ./custom/xschem/xschemrc_append >> ${XSCHEM_STAGING_$*}/xschemrc ; \ | |
| fi | |
| # In the sky130A variant, remove the reram schematic/symbol and references | |
| if test "x${XSCHEM_PATH}" != "x" ; then \ | |
| if test "x$*" == "xA" ; then \ | |
| rm -f ${XSCHEM_STAGING_$*}/sky130_tests/test_reram* ; \ | |
| rm -f ${XSCHEM_STAGING_$*}/sky130_tests/tb_reram* ; \ | |
| rm -f ${XSCHEM_STAGING_$*}/sky130_fd_pr/reram* ; \ | |
| cat ${XSCHEM_STAGING_$*}/sky130_tests/top.sch | \ | |
| ${SED} -e "/^C.*{.*reram.*}.*{.*[^}] *$$/,/.*} *$$/d" \ | |
| -e "/^C.*{.*reram.*}.*{.*} *$$/d" \ | |
| > ${XSCHEM_STAGING_$*}/temp ; \ | |
| mv ${XSCHEM_STAGING_$*}/temp ${XSCHEM_STAGING_$*}/sky130_tests/top.sch ; \ | |
| fi ; \ | |
| fi | |
| openlane-%: openlane/config.tcl openlane/sky130_fd_sc_hd/config.tcl openlane/sky130_fd_sc_hs/config.tcl openlane/sky130_fd_sc_ms/config.tcl openlane/sky130_fd_sc_ls/config.tcl openlane/sky130_fd_sc_hdll/config.tcl openlane/sky130_osu_sc_t18/config.tcl | |
| mkdir -p ${OPENLANETOP_STAGING_$*} | |
| mkdir -p ${OPENLANE_STAGING_$*} | |
| rm -rf ${OPENLANE_STAGING_$*}/custom_cells/* | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_hd | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_hs | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_ls | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_ms | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_hdll | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_fd_sc_hvl | |
| mkdir -p ${OPENLANE_STAGING_$*}/sky130_osu_sc_t18 | |
| rm -f ${OPENLANE_STAGING_$*}/common_pdn.info | |
| rm -f ${OPENLANE_STAGING_$*}/config.tcl | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_hd/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_hs/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_hdll/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_ls/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_ms/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_fd_sc_hvl/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| rm -f ${OPENLANE_STAGING_$*}/sky130_osu_sc_t18/$$file ; \ | |
| done | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.magic | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.magic | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.magic | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.spef_extractor | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.spef_extractor | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.spef_extractor | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.calibre | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.calibre | |
| rm -f ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.calibre | |
| cp -r openlane/custom_cells ${OPENLANE_STAGING_$*} | |
| cp -r openlane/cvc ${OPENLANE_STAGING_$*} | |
| ${CPP} ${SKY130$*_DEFS} openlane/config.tcl ${OPENLANE_STAGING_$*}/config.tcl | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.min.magic \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.magic | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.nom.magic \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.magic | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.max.magic \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.magic | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.min.spef_extractor \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.spef_extractor | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.nom.spef_extractor \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.spef_extractor | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.max.spef_extractor \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.spef_extractor | |
| # Only install the calibre-derived rule files if they exist in the source | |
| if test -f openlane/rules.openrcx.sky130$*.min.calibre ; then \ | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.min.calibre \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.min.calibre ;\ | |
| fi | |
| if test -f openlane/rules.openrcx.sky130$*.nom.calibre ; then \ | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.nom.calibre \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.nom.calibre ;\ | |
| fi | |
| if test -f openlane/rules.openrcx.sky130$*.max.calibre ; then \ | |
| ${CPP} ${SKY130$*_DEFS} openlane/rules.openrcx.sky130$*.max.calibre \ | |
| ${OPENLANE_STAGING_$*}/rules.openrcx.sky130$*.max.calibre ;\ | |
| fi | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_hd/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_hd/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_hs/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_hs/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_ms/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_ms/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_ls/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_ls/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_hdll/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_hdll/$$file ; \ | |
| done | |
| for file in ${OPENLANE_COMMON} ; do \ | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_fd_sc_hvl/$$file \ | |
| ${OPENLANE_STAGING_$*}/sky130_fd_sc_hvl/$$file ; \ | |
| done | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_osu_sc_t18/config.tcl \ | |
| ${OPENLANE_STAGING_$*}/sky130_osu_sc_t18/config.tcl | |
| ${CPP} -quiet ${SKY130$*_DEFS} openlane/sky130_osu_sc_t18/tracks.info \ | |
| ${OPENLANE_STAGING_$*}/sky130_osu_sc_t18/tracks.info | |
| vendor-A: primitive-build-A io-build-A sram-build-A digital-hd-build-A digital-hvl-build-A digital-hdll-build-A digital-lp-build-A digital-hs-build-A digital-ms-build-A digital-ls-build-A alpha-build-A osu-t12-build-A osu-t15-build-A osu-t18-build-A | |
| vendor-B: primitive-build-B io-build-B sram-build-B digital-hd-build-B digital-hvl-build-B digital-hdll-build-B digital-lp-build-B digital-hs-build-B digital-ms-build-B digital-ls-build-B alpha-build-B osu-t12-build-B osu-t15-build-B osu-t18-build-B | |
| primitive-build-%: | |
| # Build targets conditionally based on what repositories or submodules | |
| # were selected or initialized. To be done: Allow a library version | |
| # to be specified that overrides "latest". | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_pr/latest/cells ; then \ | |
| echo "Building primitives library and simulation models" ;\ | |
| make primitive-$*;\ | |
| fi | |
| io-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_io/latest/cells ; then \ | |
| echo "Building padframe I/O libraries" ;\ | |
| make io-$* ;\ | |
| fi | |
| digital-hd-build-%: | |
| # This assumes that at least the HD library submodule exists. Also it | |
| # assumes that the same library version is used for all libraries, which | |
| # is fine with "latest" but otherwise probably invalid. | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_hd/latest/cells ; then \ | |
| echo "Building digital high-density standard cell library" ;\ | |
| make digital-hd-$* ;\ | |
| fi | |
| digital-hvl-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_hvl/latest/cells ; then \ | |
| echo "Building digital high-voltage standard cell library" ;\ | |
| make digital-hvl-$* ;\ | |
| fi | |
| digital-hdll-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_hdll/latest/cells ; then \ | |
| echo "Building digital high-density low-leakage standard cell library" ;\ | |
| make digital-hdll-$* ;\ | |
| fi | |
| digital-lp-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_lp/latest/cells ; then \ | |
| echo "Building digital low-power standard cell library" ;\ | |
| make digital-lp-$* ;\ | |
| fi | |
| digital-hs-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_hs/latest/cells ; then \ | |
| echo "Building digital high-speed standard cell library" ;\ | |
| make digital-hs-$* ;\ | |
| fi | |
| digital-ms-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_ms/latest/cells ; then \ | |
| echo "Building digital medium-speed standard cell library" ;\ | |
| make digital-ms-$* ;\ | |
| fi | |
| digital-ls-build-%: | |
| if test -d ${SKYWATER_LIBS_PATH}/sky130_fd_sc_ls/latest/cells ; then \ | |
| echo "Building digital low-speed standard cell library" ;\ | |
| make digital-ls-$* ;\ | |
| fi | |
| alpha-build-%: | |
| if test "x${ALPHA_PATH}" != "x" ; then \ | |
| echo "Building alphanumeric layout libraries" ;\ | |
| make alpha-$* ;\ | |
| fi | |
| sram-build-%: | |
| if test "x${SRAM_PATH}" != "x" ; then \ | |
| echo "Building SRAM macro library" ;\ | |
| make sram-$* ;\ | |
| fi | |
| osu-t12-build-%: | |
| if test "x${OSU_T12_PATH}" != "x" ; then \ | |
| echo "Building OSU 12-track-high standard cell library" ;\ | |
| make osu-t12-$* ;\ | |
| fi | |
| osu-t15-build-%: | |
| if test "x${OSU_T15_PATH}" != "x" ; then \ | |
| echo "Building OSU 15-track-high standard cell library" ;\ | |
| make osu-t15-$* ;\ | |
| fi | |
| osu-t18-build-%: | |
| if test "x${OSU_T18_PATH}" != "x" ; then \ | |
| echo "Building OSU 18-track-high standard cell library" ;\ | |
| make osu-t18-$* ;\ | |
| fi | |
| primitive-%: | |
| # Install device subcircuits from vendor files | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -ngspice sky130_fd_pr/latest/models/* \ | |
| filter=custom/scripts/rename_models.py \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install device layouts from custom sources | |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130$*} \ | |
| -gds sky130_fd_pr/*.gds \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library primitive sky130_fd_pr 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install base device library from vendor files. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -gds %l/latest/cells/*/*.gds \ | |
| no-copy=custom/sky130_fd_pr/*.gds \ | |
| include=custom/sky130_fd_pr/*.gds \ | |
| compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -lef %l/latest/cells/*/*.magic.lef compile-only \ | |
| -spice %l/latest/cells/*/*.spice filter=custom/scripts/rename_cells.py \ | |
| -library primitive sky130_fd_pr 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Custom: Add "short" resistor model and subcircuit to the r+c models file | |
| cat ./custom/models/short.spice >> \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice | |
| # Custom: Add diodes as subcircuits to the r+c models file | |
| cat ./custom/models/diode.spice >> \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice | |
| # Custom: Add resistors as subcircuits to the r+c models file | |
| cat ./custom/models/resistor.spice >> \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/sky130_fd_pr__model__r+c.model.spice | |
| # Custom: Patch the r+c.mrp1monte.spice file to make the generic poly | |
| # resistor a type "R" device. | |
| ${PATCH} -p1 -f -d ${STAGING_PATH}/${SKY130$*} \ | |
| < custom/patches/sky130_fd_pr_2.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Patch the models to remove the substrate pin from the PNP | |
| # device, which has no independent substrate pin (collector=substrate) | |
| ${PATCH} -p4 -f -d ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE} \ | |
| < custom/patches/sky130_fd_pr_3.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Patch the ngspice models to add the HV diffusion resistor subcircuits | |
| ${PATCH} -p2 -f -d ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice \ | |
| < custom/patches/sky130_fd_pr_5.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Fix up the PNP model file before running the next modification | |
| head -15 ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice > ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/temp | |
| tail -39 ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice >> ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/temp | |
| mv ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/temp ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__pnp_05v5_W3p40L3p40.model.spice | |
| # Custom: Add the PNP 3.4x3.4um device model to the includes in "all.spice" | |
| ./custom/scripts/fix_spice_includes.py ${EF_FORMAT} \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/all.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Add the PNP 3.4x3.4um device model to the includes in "montecarlo.spice" | |
| ./custom/scripts/fix_spice_includes2.py ${EF_FORMAT} \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/parameters/montecarlo.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Parse the (commented out) statistics blocks and generate | |
| # ngspice-compatible monte carlo parameters for mismatch and process | |
| ./custom/scripts/mismatch_params.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/mismatch_params.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/process_params.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/process_params.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/montecarlo_hack.py -variant=${SKY130$*} \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Change vt to local_vt in one file for Xyce compatibilty | |
| ./custom/scripts/xyce_hack.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__res_iso_pw.model.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Remove ACM model parameters from BSIM3 devices | |
| ./custom/scripts/xyce_hack2.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_nfet_pass.pm3.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/xyce_hack2.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_pfet_pass.pm3.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ./custom/scripts/xyce_hack2.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${PR_SPICE}/sky130_fd_pr__special_nfet_latch.pm3.spice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Install custom corrected/enhanced sky130.lib.spice | |
| cp custom/models/sky130.lib.spice \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Add special device ID layers to bipolar layouts in magic | |
| # to make the extraction models correct. | |
| ./custom/scripts/add_bipolar_ids.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Custom: Add "spinit" file | |
| cat ./custom/models/spinit >> \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.tech/ngspice/spinit | |
| io-%: | |
| # Install custom additions to I/O pad library | |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130$*} \ | |
| -verilog %l/verilog/*.v compile-only rename=sky130_ef_io \ | |
| -cdl %l/cdl/*.cdl \ | |
| -spice %l/spice/*.spice \ | |
| -lib %l/lib/*.lib \ | |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ | |
| -lef %l/lef/*.lef exclude=sky130_fd_io__top_xres4v2.lef \ | |
| compile-only rename=sky130_ef_io \ | |
| -lef %l/lef/sky130_fd_io__top_xres4v2.lef \ | |
| -library general sky130_fd_io 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Copy the GDS file for the GPIOv2 cell, then run the script that fixes it. | |
| cp ${SKYWATER_LIBS_PATH}/sky130_fd_io/latest/cells/top_gpiov2/sky130_fd_io__top_gpiov2.gds \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${IO_GDS} | |
| ./custom/scripts/fix_gpiov2_gds.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${IO_GDS}/sky130_fd_io__top_gpiov2.gds | |
| # Install SkyWater I/O pad library | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| include=custom/sky130_fd_io/cdl/*.cdl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate lefopts=-hide compile-only \ | |
| no-copy=sky130_fd_io__top_xres4v2.lef \ | |
| include=sky130_fd_io__top_xres4v2.lef \ | |
| exclude=*.magic.lef,sky130_ef_io.lef \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| options=custom/scripts/sky130_fd_io_import.tcl \ | |
| no-copy=sky130_fd_io__top_gpiov2.gds \ | |
| include=sky130_fd_io__top_gpiov2.gds \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,sky130_ef_io.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library general sky130_fd_io 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${IO_VERILOG}/*.*.v | |
| # Add a maskhint set for the GPIO pad .mag view to prevent problems writing | |
| # when writing HVI to GDS during hierarchical adjustments. | |
| ${ADDPROP} ${STAGING_PATH}/${SKY130$*} sky130_fd_io sky130_fd_io__top_gpiov2 \ | |
| "MASKHINTS_HVI 1346 17198 5828 19224 13700 1890 15920 2360 24 17522 1778 20612" -mag | |
| # Run the add_properties.py script to add extraction information to layout | |
| # cells for which the intended device cannot be extracted. | |
| ./custom/scripts/add_properties.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| digital-hd-%: | |
| # Install custom additions to standard cell libraries | |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130$*} \ | |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ | |
| -lef %l/lef/*.lef compile-only rename=sky130_ef_sc_hd.lef \ | |
| -verilog %l/verilog/*.v \ | |
| -library digital sky130_fd_sc_hd 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_hd__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef \ | |
| exclude=*.magic.lef,sky130_ef_sc_hd.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| annotate compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| no-copy=custom/sky130_fd_sc_hd/gds/sky130_fd*.gds \ | |
| include=custom/sky130_fd_sc_hd/gds/sky130_ef*.gds \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v \ | |
| exclude=*.*.v include=custom/sky130_fd_sc_hd/verilog/*.v \ | |
| compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_hd 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=hd 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Add a maskhint set for the tap cell .mag view to prevent problems writing | |
| # when writing NSDM and PSDM to GDS during hierarchical adjustments. | |
| ${ADDPROP} ${STAGING_PATH}/${SKY130$*} sky130_fd_sc_hd \ | |
| sky130_fd_sc_hd__tapvpwrvgnd_1 \ | |
| "MASKHINTS_PSDM 0 38 92 195" -mag | |
| ${ADDPROP} ${STAGING_PATH}/${SKY130$*} sky130_fd_sc_hd \ | |
| sky130_fd_sc_hd__tapvpwrvgnd_1 \ | |
| "MASKHINTS_NSDM 0 279 92 506" -mag | |
| # Quick solution to extraction issue---connect VNB label pwell to rest | |
| ${ADDLAYER} ${STAGING_PATH}/${SKY130$*} sky130_fd_sc_hd \ | |
| sky130_fd_sc_hd__a21bo_1 \ | |
| pwell "29 17 69 157" -mag | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${HD_VERILOG}/*.*.v | |
| # Apply extra PDK patches until they get fixed properly in the source | |
| ${PATCH} -p1 -f -d ${STAGING_PATH}/${SKY130$*}/libs.ref/${HD_VERILOG} \ | |
| < custom/patches/hd_wire_syntax.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| digital-hdll-%: | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_hdll__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_hdll 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=hdll 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${HDLL_VERILOG}/*.*.v | |
| digital-hvl-%: | |
| # Install custom additions to standard cell libraries | |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130$*} \ | |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ | |
| -spice %l/spice/*.spice \ | |
| -library digital sky130_fd_sc_hvl 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_hvl__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| no-copy=custom/sky130_fd_sc_hvl/spice/sky130_fd*.spice \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| filter=custom/scripts/fix_mismatched_opcond.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| include=custom/sky130_fd_sc_hvl/gds/sky130_ef*.gds \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_hvl 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=hvl 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Add a maskhint to the HVL level shifter to represent the HVI layer as | |
| # drawn in the GDS, and so eliminate the HVI-to-nwell DRC error. | |
| ${ADDPROP} ${STAGING_PATH}/${SKY130$*} sky130_fd_sc_hvl sky130_fd_sc_hvl__lsbufhv2lv_1 \ | |
| "MASKHINTS_HVI 22 34 706 1316" -mag | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${HVL_VERILOG}/*.*.v | |
| # Custom: Patch the HVL library to correct the resistor device names | |
| ${PATCH} -p3 -f -d ${STAGING_PATH}/${SKY130$*}/libs.ref/${HVL_SPICE} \ | |
| < custom/patches/sky130_fd_pr_${HVL_PATCH4}.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| ${PATCH} -p3 -f -d ${STAGING_PATH}/${SKY130$*}/libs.ref/${HVL_CDL} \ | |
| < custom/patches/sky130_fd_pr_6.patch \ | |
| 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| digital-lp-%: | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_lp__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_lp 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=lp 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${LP_VERILOG}/*.*.v | |
| digital-hs-%: | |
| # Install custom additions to standard cell libraries | |
| ${STAGE} -source ./custom -target ${STAGING_PATH}/${SKY130$*} \ | |
| -gds %l/gds/*.gds options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_fd_sc_hs 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_hs__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| no-copy=custom/sky130_fd_sc_hs/gds/sky130_fd*.gds \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_hs 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=hs 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${HS_VERILOG}/*.*.v | |
| digital-ms-%: | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_ms__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_ms 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=ms 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${MS_VERILOG}/*.*.v | |
| digital-ls-%: | |
| # Install all SkyWater digital standard cells. | |
| ${STAGE} -source ${SKYWATER_LIBS_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef %l/latest/tech/*.tlef filter=custom/scripts/fix_techlef$*.py \ | |
| rename=sky130_fd_sc_ls__nom.tlef \ | |
| -spice %l/latest/cells/*/*.spice compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| filter=custom/scripts/fix_device_models.py \ | |
| -cdl %l/latest/cells/*/*.cdl ignore=topography compile-only \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -lef %l/latest/cells/*/*.lef annotate compile-only \ | |
| exclude=*.magic.lef lefopts=-toplayer \ | |
| filter=custom/scripts/fix_digital_lef.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -doc %l/latest/cells/*/*.pdf \ | |
| -lib %l/latest/timing/*.lib filter=custom/scripts/add_wireloads.py \ | |
| filter=custom/scripts/fix_default_fanout_load.py \ | |
| filter=custom/scripts/fix_related_bias_pins.py \ | |
| -gds %l/latest/cells/*/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/models/*/*.v exclude=*.*.v compile-only \ | |
| rename=primitives filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -verilog %l/latest/cells/*/*.*.v \ | |
| -verilog %l/latest/cells/*/*.v exclude=*.*.v,primitives.v \ | |
| compile-only filter=custom/scripts/inc_verilog.py \ | |
| sort=../common/sort_pdkfiles.py \ | |
| -library digital sky130_fd_sc_ls 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Create minimum/maximum technology LEF files | |
| ./custom/scripts/make_minmax_techlef.py ${EF_FORMAT} -variant=${SKY130$*} \ | |
| -library=ls 2>&1 | tee -a ${SKY130$*}_make.log || true | |
| # Remove the base verilog files which have already been included into | |
| # the libraries | |
| ${RM} ${STAGING_PATH}/${SKY130$*}/libs.ref/${LS_VERILOG}/*.*.v | |
| alpha-%: | |
| # Install alphanumeric library. | |
| ${STAGE} -source ${ALPHA_PATH}/.. -target ${STAGING_PATH}/${SKY130$*} \ | |
| -mag %l/mag/*.mag filter=custom/scripts/text2m5.py \ | |
| -library general sky130_ml_xx_hd 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install text2mag.py script for alphanumeric library | |
| mkdir -p ${STAGING_PATH}/${SKY130$*}/libs.ref/${MLXX_SCRIPTS} | |
| cp custom/scripts/text2mag.py \ | |
| ${STAGING_PATH}/${SKY130$*}/libs.ref/${MLXX_SCRIPTS} | |
| sram-%: | |
| # Install SRAM library. NOTE: SRAM macros share some of the same | |
| # cell names, so use special option script gds_import_sram.tcl | |
| # To do: Add option to process each GDS file individually in magic, | |
| # instead of all at once. | |
| ${STAGE} -source ${SRAM_PATH}/.. -target ${STAGING_PATH}/${SKY130$*} \ | |
| -lef %l/*/*.lef \ | |
| -lib %l/*/*.lib \ | |
| -gds %l/*/*.gds options=custom/scripts/gds_import_sram.tcl \ | |
| -spice %l/*/*.lvs.sp filter=custom/scripts/sp_to_spice.py \ | |
| -verilog %l/*/*.v \ | |
| -library general sky130_sram_macros 2>&1 | tee -a ${SKY130$*}_make.log | |
| osu-t12-%: | |
| # Install OSU T12 hs digital standard cells. | |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osu_sc_12t_hs.tlef \ | |
| -spice 12T_hs/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 12T_hs/lef/*.lef \ | |
| -lib 12T_hs/lib/*.lib \ | |
| -gds 12T_hs/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_12t_hs 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T12 ms digital standard cells. | |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osu_sc_12t_ms.tlef \ | |
| -spice 12T_ms/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 12T_ms/lef/*.lef \ | |
| -lib 12T_ms/lib/*.lib \ | |
| -gds 12T_ms/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_12t_ms 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T12 ls digital standard cells. | |
| ${STAGE} -source ${OSU_T12_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_12T.tlef rename=sky130_osu_sc_12t_ls.tlef \ | |
| -spice 12T_ls/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 12T_ls/lef/*.lef \ | |
| -lib 12T_ls/lib/*.lib \ | |
| -gds 12T_ls/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_12t_ls 2>&1 | tee -a ${SKY130$*}_make.log | |
| osu-t15-%: | |
| # Install OSU T15 hs digital standard cells. | |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osu_sc_15t_hs.tlef \ | |
| -spice 15T_hs/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 15T_hs/lef/*.lef \ | |
| -lib 15T_hs/lib/*.lib \ | |
| -gds 15T_hs/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_15t_hs 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T15 ms digital standard cells. | |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osu_sc_15t_ms.tlef \ | |
| -spice 15T_ms/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 15T_ms/lef/*.lef \ | |
| -lib 15T_ms/lib/*.lib \ | |
| -gds 15T_ms/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_15t_ms 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T15 ls digital standard cells. | |
| ${STAGE} -source ${OSU_T15_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_15T.tlef rename=sky130_osu_sc_15t_ls.tlef \ | |
| -spice 15T_ls/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 15T_ls/lef/*.lef \ | |
| -lib 15T_ls/lib/*.lib \ | |
| -gds 15T_ls/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_15t_ls 2>&1 | tee -a ${SKY130$*}_make.log | |
| osu-t18-%: | |
| # Install OSU T18 hs digital standard cells. | |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osu_sc_18t_hs.tlef \ | |
| -spice 18T_hs/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 18T_hs/lef/*.lef \ | |
| -lib 18T_hs/lib/*.lib \ | |
| -gds 18T_hs/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_18t_hs 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T18 ms digital standard cells. | |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osu_sc_18t_ms.tlef \ | |
| -spice 18T_ms/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 18T_ms/lef/*.lef \ | |
| -lib 18T_ms/lib/*.lib \ | |
| -gds 18T_ms/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_18t_ms 2>&1 | tee -a ${SKY130$*}_make.log | |
| # Install OSU T18 ls digital standard cells. | |
| ${STAGE} -source ${OSU_T18_PATH} -target ${STAGING_PATH}/${SKY130$*} \ | |
| -techlef sky130_osu_sc_18T.tlef rename=sky130_osu_sc_18t_ls.tlef \ | |
| -spice 18T_ls/cdl/*.spice compile-only exclude=*.*.spice \ | |
| -lef 18T_ls/lef/*.lef \ | |
| -lib 18T_ls/lib/*.lib \ | |
| -gds 18T_ls/gds/*.gds compile-only \ | |
| options=custom/scripts/gds_import_setup.tcl \ | |
| -library digital sky130_osu_sc_18t_ls 2>&1 | tee -a ${SKY130$*}_make.log | |
| install: $(foreach var, ${VARIANTS}, install-$(var)) | |
| install-A: | |
| echo "Starting SKY130 PDK migration on "`date` > ${SKY130A}_install.log | |
| ${INSTALL} \ | |
| -source ${STAGING_PATH}/${SKY130A} \ | |
| -finalpath ${SHARED_PDKS_PATH}/${SKY130A} \ | |
| -variable PDKPATH \ | |
| -link_from ${DIST_LINK_TARGETS_A} 2>&1 | tee -a ${SKY130A}_install.log | |
| echo "Ended SKY130 PDK migration on "`date` >> ${SKY130A}_install.log | |
| # NOTE: if DIST_LINK_TARGETS_B points back to the A variant, then the install | |
| # of B depends on the install of A. Can't think of a way to make the dependency | |
| # itself depend on the value of DIST_LINK_TARGETS_B, so I'm just forcing the | |
| # install to always be sequential: install A first, then B. | |
| install-B: install-A | |
| echo "Starting SKY130 PDK migration on "`date` > ${SKY130B}_install.log | |
| ${INSTALL} \ | |
| -source ${STAGING_PATH}/${SKY130B} \ | |
| -finalpath ${SHARED_PDKS_PATH}/${SKY130B} \ | |
| -variable PDKPATH \ | |
| -link_from ${DIST_LINK_TARGETS_B} 2>&1 | tee -a ${SKY130B}_install.log | |
| echo "Ended SKY130 PDK migration on "`date` >> ${SKY130B}_install.log | |
| uninstall: $(foreach var, ${VARIANTS}, uninstall-$(var)) | |
| uninstall-A: | |
| echo "Uninstalling SKY130 PDK from ${SHARED_PDKS_PATH}" | |
| if test "x${SHARED_PDKS_PATH}" != "x" ; then \ | |
| ${RM} -rf ${SHARED_PDKS_PATH}/${SKY130A} ; \ | |
| fi | |
| echo "Finished SKY130 PDK uninstall" | |
| uninstall-B: | |
| echo "Uninstalling SKY130 PDK from ${SHARED_PDKS_PATH}" | |
| if test "x${SHARED_PDKS_PATH}" != "x" ; then \ | |
| ${RM} -rf ${SHARED_PDKS_PATH}/${SKY130B} ; \ | |
| fi | |
| echo "Finished SKY130 PDK uninstall" | |
| clean: $(foreach var, ${VARIANTS}, clean-$(var)) | |
| clean-A: | |
| ${STAGE} -target ${STAGING_PATH}/${SKY130A} -clean | |
| clean-B: | |
| ${STAGE} -target ${STAGING_PATH}/${SKY130B} -clean | |
| veryclean: $(foreach var, ${VARIANTS}, veryclean-$(var)) | |
| veryclean-A: clean-A | |
| ${RM} ${SKY130A}_make.log | |
| ${RM} ${SKY130A}_install.log | |
| # Legacy name | |
| ${RM} ${SKY130A}_migrate.log | |
| veryclean-B: clean-B | |
| ${RM} ${SKY130B}_make.log | |
| ${RM} ${SKY130B}_install.log | |
| # Old aliases (retained for compatibility) | |
| install-dist: | |
| $(warning "'make install-dist' has been replaced with 'make install'") | |
| make install | |
| install-local: | |
| $(warning "'make install-local' has been replaced with 'make install'") | |
| make install | |
| uninstall-dist: | |
| $(warning "'make uninstall-dist' has been replaced with 'make uninstall'") | |
| make uninstall | |
| uninstall-local: | |
| $(warning "'make uninstall-local' has been replaced with 'make uninstall'") | |
| make uninstall | |
| install-dist-A: | |
| $(warning "'make install-dist-A' has been replaced with 'make install'") | |
| make install | |
| install-local-A: | |
| $(warning "'make install-local-A' has been replaced with 'make install'") | |
| make install | |
| uninstall-dist-A: | |
| $(warning "'make uninstall-dist-A' has been replaced with 'make uninstall'") | |
| make uninstall | |
| uninstall-local-A: | |
| $(warning "'make uninstall-local-A' has been replaced with 'make uninstall'") | |
| make uninstall |