| RULE NO.,DESCRIPTION,"LAYOUT |
| RULE","For Drawing OR |
| |
| DRC Check" |
| Layer,DCF-Dummy COMP Fill,, |
| ,"Use “NDMY” mark layer to exclude dummy COMP generation in |
| certain critical High frequency/RF circuit areas.",--,-- |
| DCF.1a,"All area between active polygons (COMP) (with spacing greater than |
| |
| equal to this rule) must be filled with “Dummy COMP” except area |
| |
| marked by NDMY, RES_MK, Pad and IND_MK, as well as the |
| |
| Region define by DCF.6a, 6b, 6c, 6d, 6e. |
| |
| Use rules DCF.1c to DCF.13 to drawn “Dummy COMP”",20,For DRC |
| DCF.1b,"Minimum global density for active layers (COMP+ Dummy COMP) |
| |
| Local density is governed by DCF.1a , DE.3 and DE.4",25%,For DRC |
| DCF.1c,"A staggered array of dummy COMP 5 umX5 um squares is created to |
| |
| cover the prime die (1), frame, SLM Etest patterns and SLM reliability |
| |
| test patterns.",5X5,DRC check for |
| DCF.1d,Maximum global density for active layers (COMP+ Dummy COMP),70%,For DRC |
| DCF.2a*,"Min/Max Adjacent placement Space between dummy COMP cells |
| ",3,For Drawing |
| DCF.2b,"Resulted minimum space between Dummy active in all directions |
| |
| (for DRC check)",1.9,For DRC |
| DCF.3*,Stagger both X and Y direction,1.6,For Drawing |
| DCF.4,Space from dummy COMP to COMP (circuit COMP).,3.5,For DRC |
| DCF.5,Space from dummy COMP to poly2,1.5,For DRC |
| DCF.6a,Space from dummy COMP to Nwell boundary,1.3,For DRC |
| DCF.6b,Space from dummy COMP to DNWELL boundary,4,For DRC |
| DCF.6c,Space from dummy COMP to LVPWELL boundary,1.3,For DRC |
| DCF.6d,Space from dummy COMP to Dualgate boundary,1.3,For DRC |
| DCF.7a*,"Space from dummy COMP in prime die including guard ring to the |
| |
| scribe line",26,For DRC |
| DCF.7b*,"Space from dummy COMP in frame to edge of frame (valid only for |
| |
| scribe lines)",6,For DRC |
| DCF.7c*,"Space from dummy COMP in frame to any frame cell except non-ET |
| |
| (valid only for scribe line structures)",10,For Drawing |
| DCF.7d*,"Space from dummy COMP in SLM Etest patterns or SLM reliability |
| |
| test patterns to the boundary of test patterns (valid only for scribe line |
| |
| Structures)",6,For DRC |
| DCF.8a,"Space from dummy COMP to Resistor marking layer (RES_MK). |
| |
| Dummy COMP should not exit under RES_MK",3.5,For DRC |
| DCF.8b,"There must be at least one row of dummy COMP (or substrate tie) |
| |
| between RES_MK layer and the transistor channel active if RES_MK |
| |
| layer's both side (x and y) dimensions are greater than:",80,For DRC |
| DCF.9*,"Space from dummy COMP to Pad |
| |
| (Just a guideline for RF circuits)",7,"Guideline only,no DRC" |
| DCF.10*,"Remove truncated dummy squares (Truncated Dummy COMP shall |
| |
| not exist)",--,For DRC |
| DCF.11a,"Dummy COMP cannot exit under “NDMY” marking layer and space |
| |
| from dummy COMP to dummy COMP excluding layer (NDMY) (2)",3.5,For DRC |
| DCF.11b,"There must be at least one row of dummy COMP (or substrate tie) |
| |
| between NDMY layer and the transistor channel active if NDMY |
| layer's both side (x and y) dimensions are greater than:",80,For DRC |
| DCF.12,Minimum dummy COMP space to IND_MK layer,3,For DRC |
| DCF.13,"Dummy COMP should not exist under IND_MK layer There must be |
| |
| at least one row of dummy COMP (or substrate tie) between |
| |
| IND_MK layer and the transistor channel active if IND_MK layer's |
| |
| both side (x and y) dimensions are greater than:",80, |