//////////////////////////////////////////////////////////////////////////////
// SPDX-FileCopyrightText: 2021 , Dinesh Annayya                          
// 
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
// SPDX-FileContributor: Created by Dinesh Annayya <dinesha@opencores.org>
//
//////////////////////////////////////////////////////////////////////
////                                                              ////
////  Digital core                                                ////
////                                                              ////
////  This file is part of the riscduino cores project            ////
////  https://github.com/dineshannayya/riscduino.git              ////
////                                                              ////
////  Description                                                 ////
////      This is digital core and integrate all the main block   ////
////      here.  Following block are integrated here              ////
////      1.  32 bit Risc V Core  * 4 core                        ////
////      2.  Quad SPI Master(SPI Flash/SRAM)                     ////
////      3.  Wishbone Cross Bar                                  ////
////      4.  2 x UART                                            ////
////      5,  USB 1.1 Host                                        ////
////      6.  SPI Master (Single)                                 ////
////      7.  TCM SRAM 2KB                                        ////
////      8.  2KB icache and 2KB dcache                           ////
////      9.  6 Channel ADC (Pending)                             ////
////      10. Pinmux with GPIO and 6 PWM                          ////
////      11. 15 x hardware Semaphore                             ////
////      12. 4 x ws281x driver                                   //// 
////      13. 3 x Hardware Timer                                  ////
////      14. UART Master                                         ////
////      15. SPI Slave (As Arduino ISP)                          ////
////                                                              ////
////  To Do:                                                      ////
////    nothing                                                   ////
////                                                              ////
////  Author(s):                                                  ////
////      - Dinesh Annayya, dinesh.annayya@gmail.com              ////
////                                                              ////
////  Revision :                                                  ////
////    0.1 - 16th Feb 2021, Dinesh A                             ////
////          Initial integration with Risc-V core +              ////
////          Wishbone Cross Bar + SPI  Master                    ////
////    0.2 - 17th June 2021, Dinesh A                            ////
////        1. In risc core, wishbone and core domain is          ////
////           created                                            ////
////        2. cpu and rtc clock are generated in glbl reg block  ////
////        3. in wishbone interconnect:- Stagging flop are added ////
////           at interface to break wishbone timing path         ////
////        4. buswidth warning are fixed inside spi_master       ////
////        modified rtl files are                                ////
////           verilog/rtl/digital_core/src/digital_core.sv       ////
////           verilog/rtl/digital_core/src/glbl_cfg.sv           ////
////           verilog/rtl/lib/wb_stagging.sv                     ////
////           verilog/rtl/syntacore/scr1/src/top/scr1_dmem_wb.sv ////
////           verilog/rtl/syntacore/scr1/src/top/scr1_imem_wb.sv ////
////           verilog/rtl/syntacore/scr1/src/top/scr1_top_wb.sv  ////
////           verilog/rtl/user_project_wrapper.v                 ////
////           verilog/rtl/wb_interconnect/src/wb_interconnect.sv ////
////           verilog/rtl/spi_master/src/spim_clkgen.sv          ////
////           verilog/rtl/spi_master/src/spim_ctrl.sv            ////
////    0.3 - 20th June 2021, Dinesh A                            ////
////           1. uart core is integrated                         ////
////           2. 3rd Slave ported added to wishbone interconnect ////
////    0.4 - 25th June 2021, Dinesh A                            ////
////          Moved the pad logic inside sdram,spi,uart block to  ////
////          avoid logic at digital core level                   ////
////    0.5 - 25th June 2021, Dinesh A                            ////
////          Since carvel gives only 16MB address space for user ////
////          space, we have implemented indirect address select  ////
////          with 8 bit bank select given inside wb_host         ////
////          core Address = {Bank_Sel[7:0], Wb_Address[23:0]     ////
////          caravel user address space is                       ////
////          0x3000_0000 to 0x30FF_FFFF                          ////
////    0.6 - 27th June 2021, Dinesh A                            ////
////          Digital core level tie are moved inside IP to avoid ////
////          power hook up at core level                         ////
////          u_risc_top - test_mode & test_rst_n                 ////
////          u_intercon - s*_wbd_err_i                           ////
////          unused wb_cti_i is removed from u_sdram_ctrl        ////
////    0.7 - 28th June 2021, Dinesh A                            ////
////          wb_interconnect master port are interchanged for    ////
////          better physical placement.                          ////
////          m0 - External HOST                                  ////
////          m1 - RISC IMEM                                      ////
////          m2 - RISC DMEM                                      ////
////    0.8 - 6th July 2021, Dinesh A                             ////
////          For Better SDRAM Interface timing we have taping    ////
////          sdram_clock goint to io_out[29] directly from       ////
////          global register block, this help in better SDRAM    ////
////          interface timing control                            ////
////    0.9 - 7th July 2021, Dinesh A                             ////
////          Removed 2 Unused port connection io_in[31:30] to    ////
////          spi_master to avoid lvs issue                       ////
////    1.0 - 28th July 2021, Dinesh A                            ////
////          i2cm integrated part of uart_i2cm module,           ////
////          due to number of IO pin limitation,                 ////
////          Only UART OR I2C selected based on config mode      ////
////    1.1 - 1st Aug 2021, Dinesh A                              ////
////          usb1.1 host integrated part of uart_i2cm_usb module,////
////          due to number of IO pin limitation,                 ////
////          Only UART/I2C/USB selected based on config mode     ////
////    1.2 - 29th Sept 2021, Dinesh.A                            ////
////          1. copied the repo from yifive and renames as       ////
////             riscdunino                                       ////
////          2. Removed the SDRAM controlled                     ////
////          3. Added PinMux                                     ////
////          4. Added SAR ADC for 6 channel                      ////
////    1.3 - 30th Sept 2021, Dinesh.A                            ////
////          2KB SRAM Interface added to RISC Core               ////
////    1.4 - 13th Oct 2021, Dinesh A                             ////
////          Basic verification and Synthesis cleanup            ////
////    1.5 - 6th Nov 2021, Dinesh A                              ////
////          Clock Skew block moved inside respective block due  ////
////          to top-level power hook-up challenges for small IP  ////
////    1.6   Nov 14, 2021, Dinesh A                              ////
////          Major bug, clock divider inside the wb_host reset   ////
////          connectivity open is fixed                          ////
////    1.7   Nov 15, 2021, Dinesh A                              ////
////           Bug fix in clk_ctrl High/Low counter width         ////
////           Removed sram_clock                                 ////
////    1.8  Nov 23, 2021, Dinesh A                               ////
////          Three Chip Specific Signature added at PinMux Reg   ////
////          reg_22,reg_23,reg_24                                ////
////    1.9  Dec 11, 2021, Dinesh A                               ////
////         2 x 2K SRAM added into Wishbone Interface            ////
////         Temporary ADC block removed                          ////
////    2.0  Dec 14, 2021, Dinesh A                               ////
////         Added two more 2K SRAM added into Wishbone Interface ////
////    2.1  Dec 16, 2021, Dinesh A                               ////
////      1.4 MBIST controller changed to single one              ////
////      2.Added one more SRAM to TCM memory                     ////
////      3.WishBone Interconnect chang to take care mbist changes////
////      4.Pinmux change to take care of mbist changes           ////
////    2.2  Dec 20, 2021, Dinesh A                               ////
////      1. MBIST design issue fix for yosys                     ////
////      2. Full chip Timing and Transition clean-up             ////                   
////    2.3  Dec 24, 2021, Dinesh A                               ////
////      UART Master added with message handler at wb_host       ////
////    2.4  Jan 01, 2022, Dinesh A                               ////
////       LA[0] is added as soft reset option at wb_port         ////
////    2.5  Jan 06, 2022, Dinesh A                               ////
////       TCM RAM Bug fix inside syntacore                       ////
////    2.6  Jan 08, 2022, Dinesh A                               ////
////        Pinmux Interrupt Logic change                         ////
////    3.0  Jan 14, 2022, Dinesh A                               ////
////        Moving from riscv core from syntacore/scr1 to         ////
////        yfive/ycr1 on sankranti 2022 (A Hindu New Year)       ////
////    3.1  Jan 15, 2022, Dinesh A                               ////
////         Major changes in qspim logic to handle special mode  ////
////    3.2  Feb 02, 2022, Dinesh A                               ////
////         Bug fix around icache/dcache and wishbone burst      ////
////         access clean-up                                      ////
////    3.3  Feb 08, 2022, Dinesh A                               ////
////         support added spisram support in qspim ip            ////
////         There are 4 chip select available in qspim           ////
////         CS#0/CS#1 targeted for SPI FLASH                     ////
////         CS#2/CS#3 targeted for SPI SRAM                      ////
////    3.4  Feb 14, 2022, Dinesh A                               ////
////         burst mode supported added in imem buffer inside     ////
////         riscv core                                           ////
////    3.5  Feb 22, 2022 Dinesh A                                ////
////      A. To create more space in die, we have removed mbist   ////
////         controller and 4x 2KB RAM                            ////
////      B. Risc core will have core with common icache,dcache   ////
////            TCM memory                                        ////
////      C. Individual block reset are moved to pinmux to        ////
////         support peripheral reset from Risc and WishBone      ////
////         Host.                                                ////
////    3.6  Feb 19, Dinesh A                                     ////
////       A.  Changed Module: wb_host                            ////
////       wishbone slave clock generation config increase from   ////
////       3 to 4 bit support clock source selection              ////
////       B.  Changed Module: qspim                              ////
////        1. Bug fix in spi rise and fall pulse relation w.r.t  ////
////           spi_clk. Note: Previous version work only with     ////
////           spi clock config = 0x2                             ////
////        2. spi_oen generation fix for different spi mode      ////
////        3. spi_csn de-assertion fix for different spi clk div ////
////    3.7  Mar 2 2022, Dinesh A                                 ////
////       1. qspi cs# port mapping changed from io 28:25 to 25:28////
////       2. sspi, bug fix in reg access and endian support added////
////       3. Wishbone interconnect now support cross-connect     ////
////          feature                                             ////
////    3.8  Mar 10 2022, Dinesh A                                ////
////         1. usb chip select bug inside uart_* wrapper         ////
////         2. in wb_host, increased usb clk ctrl to 4 to 8 bit  ////
////    3.9  Mar 16 2022, Dinesh A                                ////
////         1. 3 Timer added                                     ////
////         2. Pinmux Register address movement                  ////
////         3. Risc fuse_mhartid is removed and internal tied    ////
////            inside risc core                                  ////
////         4. caravel wb addressing issue restrict to 0x300FFFFF////
////    4.0  Mar 26 2022, Dinesh A                                ////
////         1. Four core risc v integration                      ////
////    4.1  April 1 2022, Dinesh A                               ////
////         1. sram lanuch phase control added inside risc core  ////
////    4.2  April 6 2022, Dinesh A                               ////
////         1. SSPI CS# increased from 1 to 4                    ////
////         2. uart port increase to two                         ////
////    4.3  May 24 2022, Dinesh A                                ////
////         Re targetted the design to mpw-6 tools set and risc  ////
////         core logic are timing optimized to 100mhz            ////
////    4.4  May 29 2022, Dinesh A                                ////
////         1. Digital PLL integrated and clock debug signal add ////
////           @digitial io [33] port                             ////
////    4.6  June 13 2022, Dinesh A                               ////
////         1. icache and dcache bypass config addded            ////
////    4.7  July 08 2022, Dinesh A                               ////
////          Pinmux changes to support SPI CS port matching to   ////
////          arduino                                             ////
////    4.8  July 20 2022, Dinesh A                               ////
////         SPI ISP boot option added in wb_host, spi slave uses ////
////         same spi master interface, but will be active only   ////
////         when internal SPI config disabled + RESET PIN = 0    ////
////    4.9  Aug 5 2022, Dinesh A                                 ////
////         changes in sspim                                     ////
////           A. SPI Mode 0 to 3 support added,                  ////
////           B. SPI Duplex mode TX-RX Mode added                ////
////    5.0  Aug 15 2022, Dinesh A                                ////
////          A. 15 Hardware Semahore added                       ////
////          B. Pinmux Address Space are Split as                ////
////             `define ADDR_SPACE_PINMUX  32'h1002_0000         ////
////             `define ADDR_SPACE_GLBL    32'h1002_0000         ////
////             `define ADDR_SPACE_GPIO    32'h1002_0040         ////
////             `define ADDR_SPACE_PWM     32'h1002_0080         ////
////             `define ADDR_SPACE_TIMER   32'h1002_00C0         ////
////             `define ADDR_SPACE_SEMA    32'h1002_0100         ////
////    5.1  Aug 24 2022, Dinesh A                                ////
////          A. GPIO interrupt generation changed from 1 to 32   ////
////          B. Total interrupt to Riscv changed from 16 to 32   ////
////          C. uart_master disable option added at pinmux       ////
////          D. Timer interrupt related clean-up                 ////
////          E. 4x ws281x driver logic added                     ////
////          F. 4x ws281x driver are mux with 16x gpio           ////
////          G. gpio type select the normal gpio vs ws281x       ////
////    5.2  Aug 26 2022, Dinesh A                                ////
////          A. We have copied the user_defines.h from caravel   ////
////          and configured all the GPIO from 5 onwards as       ////
////          GPIO_MODE_USER_STD_BIDIRECTIONAL                    ////
////                                                              ////
////          As digitial-io[0-5] reserved at power up.           ////
////          B. to keep at least one uart access,                ////
////              we have moved UART_RXD[1] from io[3] to io[6]   ////
////          C. SPI Slave SSN move from io[0] to [7]             ////
////    5.3  Sept 2 2022, Dinesh A                                ////
////          A. System Strap implementation                      ////
////          B. Arduino pins are moved to take care of caravel   ////
////            digital-io[0-4] resevred                          ////
////          C. global register space increased from 16 to 32    ////
////          D. reset fsm is implementation with soft reboot     ////
////             option                                           ////
////          E. strap based booting option added for qspi        ////
////    5.4  Sept 7 2022, Dinesh A                                ////
////          A. PLL configuration are moved from wb_host to      ////
////          pinmux to help risc core to do pll config and reboot////
////          B. PLL configuration are kept in p_reset_n to avoid ////
////           initialized on soft reboot.                        ////
////          C. Master Uart has two strap bit to control the     ////
////          boot up config                                      ////
////          2'b00 - 50Mhz, 2'b01 - 40Mhz, 2'b10 - 50Mhz,        ////
////          2'b11 - LA control                                  ////
////    5.5  Sept 14 2022, Dinesh A                               ////
////          A. Auto Baud detection added in uart master as      ////
////          power on user_clock1 is not decided, strap def      ////
////          changed                                             ////
////          2'b00 - Auto, 2'b01 - 50Mhz, 2'b10 - 4Mhz,          ////
////          2'b11 - LA control                                  ////
////          B. digital_pll is re-synth with maual placement     ////
////    5.6  Sept 29 2022, Dinesh A                               ////
////         A. 4x 8bit DAC Integration                           ////
////         B. clock skew control added for core clock           ////
////    5.8  Nov 20, 2022, Dinesh A                               ////
////         A. Pinmux - Double Sync added for usb & i2c inter    ////
////    5.9  Nov 25, 2022, Dinesh A                               ////
////         cpu_clk will be feed through wb_interconnect for     ////
////         buffering purpose                                    ////
////    6.0  Nov 27, 2022, Dinesh A                               ////
////         MPW-7 Timing clean setup
//////////////////////////////////////////////////////////////////////
////                                                              ////
//// Copyright (C) 2000 Authors and OPENCORES.ORG                 ////
////                                                              ////
//// This source file may be used and distributed without         ////
//// restriction provided that this copyright statement is not    ////
//// removed from the file and that any derivative work contains  ////
//// the original copyright notice and the associated disclaimer. ////
////                                                              ////
//// This source file is free software; you can redistribute it   ////
//// and/or modify it under the terms of the GNU Lesser General   ////
//// Public License as published by the Free Software Foundation; ////
//// either version 2.1 of the License, or (at your option) any   ////
//// later version.                                               ////
////                                                              ////
//// This source is distributed in the hope that it will be       ////
//// useful, but WITHOUT ANY WARRANTY; without even the implied   ////
//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR      ////
//// PURPOSE.  See the GNU Lesser General Public License for more ////
//// details.                                                     ////
////                                                              ////
//// You should have received a copy of the GNU Lesser General    ////
//// Public License along with this source; if not, download it   ////
//// from http://www.opencores.org/lgpl.shtml                     ////
////                                                              ////
//////////////////////////////////////////////////////////////////////

/*********************************************************************
    Memory Map:                                               ////
                                                              ////
       SOC Memory Map                                         ////
       0x0000_0000 to 0x0FFF_FFFF  - QSPIM MEMORY             ////
       0x1000_0000 to 0x1000_00FF  - QSPIM REG
       0x1001_0000 to 0x1001_003F  - UART0
       0x1001_0040 to 0x1001_007F  - I2
       0x1001_0080 to 0x1001_00BF  - USB
       0x1001_00C0 to 0x1001_00FF  - SSPIM
       0x1001_0100 to 0x1001_013F  - UART1
       0x1002_0000 to 0x1002_00FF  - PINMUX

       Caravel Memory Map:
-----------------------------------------------------------------------
      caravel user space is 0x3000_0000 to 0x300F_FFFF
      So we have allocated 
      0x3008_0000 - 0x3008_00FF - Assigned to WB Host Address Space
      Since We need more than 16MB Address space to access SDRAM/SPI we have
      added indirect MSB 13 bit address select option
      So Address will be {Bank_Sel[15:3], wbm_adr_i[18:0]}
 ---------------------------------------------------------------------
       0x3080_0000 to 0x3080_00FF  - WB HOST 
       0x3000_0000 to 0x307F_FFFF  - Indirect Address
                                     {Bank_Sel[15:3],WB ADDR[18:0]}
***********************************************************************/
/***********************************************************************
 * Caravel I/O mapping 
 *
 * mprj_io[37]  io_in/out/oeb/in_3v3[26]  ---                    ---
 * mprj_io[36]  io_in/out/oeb/in_3v3[25]  ---                    ---
 * mprj_io[35]  io_in/out/oeb/in_3v3[24]  gpio_analog/noesd[17]  ---
 * mprj_io[34]  io_in/out/oeb/in_3v3[23]  gpio_analog/noesd[16]  ---
 * mprj_io[33]  io_in/out/oeb/in_3v3[22]  gpio_analog/noesd[15]  ---
 * mprj_io[32]  io_in/out/oeb/in_3v3[21]  gpio_analog/noesd[14]  ---
 * mprj_io[31]  io_in/out/oeb/in_3v3[20]  gpio_analog/noesd[13]  ---
 * mprj_io[30]  io_in/out/oeb/in_3v3[19]  gpio_analog/noesd[12]  ---
 * mprj_io[29]  io_in/out/oeb/in_3v3[18]  gpio_analog/noesd[11]  ---
 * mprj_io[28]  io_in/out/oeb/in_3v3[17]  gpio_analog/noesd[10]  ---
 * mprj_io[27]  io_in/out/oeb/in_3v3[16]  gpio_analog/noesd[9]   ---
 * mprj_io[26]  io_in/out/oeb/in_3v3[15]  gpio_analog/noesd[8]   ---
 * mprj_io[25]  io_in/out/oeb/in_3v3[14]  gpio_analog/noesd[7]   ---
 * mprj_io[24]  ---                       ---                    user_analog[10]
 * mprj_io[23]  ---                       ---                    user_analog[9]
 * mprj_io[22]  ---                       ---                    user_analog[8]
 * mprj_io[21]  ---                       ---                    user_analog[7]
 * mprj_io[20]  ---                       ---                    user_analog[6]  clamp[2]
 * mprj_io[19]  ---                       ---                    user_analog[5]  clamp[1]
 * mprj_io[18]  ---                       ---                    user_analog[4]  clamp[0]
 * mprj_io[17]  ---                       ---                    user_analog[3]
 * mprj_io[16]  ---                       ---                    user_analog[2]
 * mprj_io[15]  ---                       ---                    user_analog[1]
 * mprj_io[14]  ---                       ---                    user_analog[0]
 * mprj_io[13]  io_in/out/oeb/in_3v3[13]  gpio_analog/noesd[6]   ---
 * mprj_io[12]  io_in/out/oeb/in_3v3[12]  gpio_analog/noesd[5]   ---
 * mprj_io[11]  io_in/out/oeb/in_3v3[11]  gpio_analog/noesd[4]   ---
 * mprj_io[10]  io_in/out/oeb/in_3v3[10]  gpio_analog/noesd[3]   ---
 * mprj_io[9]   io_in/out/oeb/in_3v3[9]   gpio_analog/noesd[2]   ---
 * mprj_io[8]   io_in/out/oeb/in_3v3[8]   gpio_analog/noesd[1]   ---
 * mprj_io[7]   io_in/out/oeb/in_3v3[7]   gpio_analog/noesd[0]   ---
 * mprj_io[6]   io_in/out/oeb/in_3v3[6]   ---                    ---
 * mprj_io[5]   io_in/out/oeb/in_3v3[5]   ---                    ---
 * mprj_io[4]   io_in/out/oeb/in_3v3[4]   ---                    ---
 * mprj_io[3]   io_in/out/oeb/in_3v3[3]   ---                    ---
 * mprj_io[2]   io_in/out/oeb/in_3v3[2]   ---                    ---
 * mprj_io[1]   io_in/out/oeb/in_3v3[1]   ---                    ---
 * mprj_io[0]   io_in/out/oeb/in_3v3[0]   ---                    ---


************************************************************************/

`include "user_params.svh"

module user_project_wrapper (
`ifdef USE_POWER_PINS
    inout vdda1,	// User area 1 3.3V supply
    inout vdda2,	// User area 2 3.3V supply
    inout vssa1,	// User area 1 analog ground
    inout vssa2,	// User area 2 analog ground
    inout vccd1,	// User area 1 1.8V supply
    inout vccd2,	// User area 2 1.8v supply
    inout vssd1,	// User area 1 digital ground
    inout vssd2,	// User area 2 digital ground
`endif
    input   wire                       wb_clk_i        ,  // System clock
    input   wire                       user_clock2     ,  // user Clock
    input   wire                       wb_rst_i        ,  // Regular Reset signal

    input   wire                       wbs_cyc_i       ,  // strobe/request
    input   wire                       wbs_stb_i       ,  // strobe/request
    input   wire [WB_WIDTH-1:0]        wbs_adr_i       ,  // address
    input   wire                       wbs_we_i        ,  // write
    input   wire [WB_WIDTH-1:0]        wbs_dat_i       ,  // data output
    input   wire [3:0]                 wbs_sel_i       ,  // byte enable
    output  wire [WB_WIDTH-1:0]        wbs_dat_o       ,  // data input
    output  wire                       wbs_ack_o       ,  // acknowlegement

    // Analog (direct connection to GPIO pad---use with caution)
    // Note that analog I/O is not available on the 7 lowest-numbered
    // GPIO pads, and so the analog_io indexing is offset from the
    // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
    inout [28:0] analog_io,
 
    // Logic Analyzer Signals
    input  wire [127:0]                la_data_in      ,
    output wire [127:0]                la_data_out     ,
    input  wire [127:0]                la_oenb         ,
 

    // IOs
    input  wire  [37:0]                io_in           ,
    output wire  [37:0]                io_out          ,
    output wire  [37:0]                io_oeb          ,

    output wire  [2:0]                 user_irq             

);

//---------------------------------------------------
// Local Parameter Declaration
// --------------------------------------------------

parameter     BIST_NO_SRAM  = 4; // NO of MBIST MEMORY
parameter     SDR_DW        = 8;  // SDR Data Width 
parameter     SDR_BW        = 1;  // SDR Byte Width
parameter     WB_WIDTH      = 32; // WB ADDRESS/DARA WIDTH
parameter     BIST1_ADDR_WD = 11; // 512x32 SRAM
parameter     BIST_DATA_WD  = 32;

//---------------------------------------------------------------------
// Wishbone Risc V Dcache Memory Interface
//---------------------------------------------------------------------
wire                           wbd_riscv_dcache_stb_i                 ; // strobe/request
wire   [WB_WIDTH-1:0]          wbd_riscv_dcache_adr_i                 ; // address
wire                           wbd_riscv_dcache_we_i                  ; // write
wire   [WB_WIDTH-1:0]          wbd_riscv_dcache_dat_i                 ; // data output
wire   [3:0]                   wbd_riscv_dcache_sel_i                 ; // byte enable
wire   [9:0]                   wbd_riscv_dcache_bl_i                  ; // burst length
wire                           wbd_riscv_dcache_bry_i                 ; // burst ready
wire   [WB_WIDTH-1:0]          wbd_riscv_dcache_dat_o                 ; // data input
wire                           wbd_riscv_dcache_ack_o                 ; // acknowlegement
wire                           wbd_riscv_dcache_lack_o                ; // last burst acknowlegement
wire                           wbd_riscv_dcache_err_o                 ; // error

// CACHE SRAM Memory I/F
wire                           dcache_mem_clk0                        ; // CLK
wire                           dcache_mem_csb0                        ; // CS#
wire                           dcache_mem_web0                        ; // WE#
wire   [8:0]                   dcache_mem_addr0                       ; // Address
wire   [3:0]                   dcache_mem_wmask0                      ; // WMASK#
wire   [31:0]                  dcache_mem_din0                        ; // Write Data
wire   [31:0]                  dcache_mem_dout0                       ; // Read Data
   
// SRAM-0 PORT-1, IMEM I/F
wire                           dcache_mem_clk1                        ; // CLK
wire                           dcache_mem_csb1                        ; // CS#
wire  [8:0]                    dcache_mem_addr1                       ; // Address
wire  [31:0]                   dcache_mem_dout1                       ; // Read Data
//---------------------------------------------------------------------
// Wishbone Risc V Icache Memory Interface
//---------------------------------------------------------------------
wire                           wbd_riscv_icache_stb_i                 ; // strobe/request
wire   [WB_WIDTH-1:0]          wbd_riscv_icache_adr_i                 ; // address
wire                           wbd_riscv_icache_we_i                  ; // write
wire   [3:0]                   wbd_riscv_icache_sel_i                 ; // byte enable
wire   [9:0]                   wbd_riscv_icache_bl_i                  ; // burst length
wire                           wbd_riscv_icache_bry_i                 ; // burst ready
wire   [WB_WIDTH-1:0]          wbd_riscv_icache_dat_o                 ; // data input
wire                           wbd_riscv_icache_ack_o                 ; // acknowlegement
wire                           wbd_riscv_icache_lack_o                ; // last burst acknowlegement
wire                           wbd_riscv_icache_err_o                 ; // error

// CACHE SRAM Memory I/F
wire                           icache_mem_clk0                        ; // CLK
wire                           icache_mem_csb0                        ; // CS#
wire                           icache_mem_web0                        ; // WE#
wire   [8:0]                   icache_mem_addr0                       ; // Address
wire   [3:0]                   icache_mem_wmask0                      ; // WMASK#
wire   [31:0]                  icache_mem_din0                        ; // Write Data
// wire   [31:0]               icache_mem_dout0                       ; // Read Data
   
// SRAM-0 PORT-1, IMEM I/F
wire                           icache_mem_clk1                        ; // CLK
wire                           icache_mem_csb1                        ; // CS#
wire  [8:0]                    icache_mem_addr1                       ; // Address
wire  [31:0]                   icache_mem_dout1                       ; // Read Data

//---------------------------------------------------------------------
// RISC V Wishbone Data Memory Interface
//---------------------------------------------------------------------
wire                           wbd_riscv_dmem_stb_i                   ; // strobe/request
wire   [WB_WIDTH-1:0]          wbd_riscv_dmem_adr_i                   ; // address
wire                           wbd_riscv_dmem_we_i                    ; // write
wire   [WB_WIDTH-1:0]          wbd_riscv_dmem_dat_i                   ; // data output
wire   [3:0]                   wbd_riscv_dmem_sel_i                   ; // byte enable
wire   [2:0]                   wbd_riscv_dmem_bl_i                    ; // byte enable
wire                           wbd_riscv_dmem_bry_i                   ; // burst access ready
wire   [WB_WIDTH-1:0]          wbd_riscv_dmem_dat_o                   ; // data input
wire                           wbd_riscv_dmem_ack_o                   ; // acknowlegement
wire                           wbd_riscv_dmem_lack_o                  ; // acknowlegement
wire                           wbd_riscv_dmem_err_o                   ; // error

//---------------------------------------------------------------------
// WB HOST Interface
//---------------------------------------------------------------------
wire                           wbd_int_cyc_i                          ; // strobe/request
wire                           wbd_int_stb_i                          ; // strobe/request
wire   [WB_WIDTH-1:0]          wbd_int_adr_i                          ; // address
wire                           wbd_int_we_i                           ; // write
wire   [WB_WIDTH-1:0]          wbd_int_dat_i                          ; // data output
wire   [3:0]                   wbd_int_sel_i                          ; // byte enable
wire   [WB_WIDTH-1:0]          wbd_int_dat_o                          ; // data input
wire                           wbd_int_ack_o                          ; // acknowlegement
wire                           wbd_int_err_o                          ; // error
//---------------------------------------------------------------------
//    SPI Master Wishbone Interface
//---------------------------------------------------------------------
wire                           wbd_spim_stb_o                         ; // strobe/request
wire   [WB_WIDTH-1:0]          wbd_spim_adr_o                         ; // address
wire                           wbd_spim_we_o                          ; // write
wire   [WB_WIDTH-1:0]          wbd_spim_dat_o                         ; // data output
wire   [3:0]                   wbd_spim_sel_o                         ; // byte enable
wire   [9:0]                   wbd_spim_bl_o                          ; // Burst count
wire                           wbd_spim_bry_o                         ; // Busrt Ready
wire                           wbd_spim_cyc_o                         ;
wire   [WB_WIDTH-1:0]          wbd_spim_dat_i                         ; // data input
wire                           wbd_spim_ack_i                         ; // acknowlegement
wire                           wbd_spim_lack_i                        ; // Last acknowlegement
wire                           wbd_spim_err_i                         ; // error

//---------------------------------------------------------------------
//    SPI Master Wishbone Interface
//---------------------------------------------------------------------
wire                           wbd_adc_stb_o                          ;
wire [7:0]                     wbd_adc_adr_o                          ;
wire                           wbd_adc_we_o                           ; // 1 - Write, 0 - Read
wire [WB_WIDTH-1:0]            wbd_adc_dat_o                          ;
wire [WB_WIDTH/8-1:0]          wbd_adc_sel_o                          ; // Byte enable
wire                           wbd_adc_cyc_o                          ;
wire  [2:0]                    wbd_adc_cti_o                          ;
wire  [WB_WIDTH-1:0]           wbd_adc_dat_i                          ;
wire                           wbd_adc_ack_i                          ;

//---------------------------------------------------------------------
//    Global Register Wishbone Interface
//---------------------------------------------------------------------
wire                           wbd_glbl_stb_o                         ; // strobe/request
wire   [9:0]                   wbd_glbl_adr_o                         ; // address
wire                           wbd_glbl_we_o                          ; // write
wire   [WB_WIDTH-1:0]          wbd_glbl_dat_o                         ; // data output
wire   [3:0]                   wbd_glbl_sel_o                         ; // byte enable
wire                           wbd_glbl_cyc_o                         ;
wire   [WB_WIDTH-1:0]          wbd_glbl_dat_i                         ; // data input
wire                           wbd_glbl_ack_i                         ; // acknowlegement
wire                           wbd_glbl_err_i                         ; // error

//---------------------------------------------------------------------
//    Global Register Wishbone Interface
//---------------------------------------------------------------------
wire                           wbd_uart_stb_o                         ; // strobe/request
wire   [8:0]                   wbd_uart_adr_o                         ; // address
wire                           wbd_uart_we_o                          ; // write
wire   [31:0]                  wbd_uart_dat_o                         ; // data output
wire   [3:0]                   wbd_uart_sel_o                         ; // byte enable
wire                           wbd_uart_cyc_o                         ;
wire   [31:0]                  wbd_uart_dat_i                         ; // data input
wire                           wbd_uart_ack_i                         ; // acknowlegement
wire                           wbd_uart_err_i                         ;  // error


//----------------------------------------------------
//  CPU Configuration
//----------------------------------------------------
wire                           cpu_intf_rst_n                         ;
wire  [3:0]                    cpu_core_rst_n                         ;
wire                           qspim_rst_n                            ;
wire                           sspim_rst_n                            ;
wire [1:0]                     uart_rst_n                             ; // uart reset
wire                           i2c_rst_n                              ; // i2c reset
wire                           usb_rst_n                              ; // i2c reset
wire                           bist_rst_n                             ; // i2c reset
wire                           cpu_clk                                ;
wire                           rtc_clk                                ;
wire                           usb_clk                                ;
wire                           wbd_clk_int                            ;
wire                           wbd_clk_wh                             ;

wire                           wbd_clk_spi                            ;
wire                           wbd_clk_pinmux                         ;
wire                           wbd_int_rst_n                          ;
wire                           wbd_pll_rst_n                          ;

wire [31:0]                    irq_lines                              ;
wire                           soft_irq                               ;


wire [7:0]                     cfg_glb_ctrl                           ;
wire [31:0]                    cfg_clk_skew_ctrl1                     ;
wire [31:0]                    cfg_clk_skew_ctrl2                     ;
wire [3:0]                     cfg_wcska_wi                            ; // clock skew adjust for wishbone interconnect
wire [3:0]                     cfg_wcska_wh                            ; // clock skew adjust for web host

wire [3:0]                     cfg_wcska_riscv                         ; // clock skew adjust for riscv
wire [3:0]                     cfg_wcska_uart                          ; // clock skew adjust for uart
wire [3:0]                     cfg_wcska_qspi                          ; // clock skew adjust for spi
wire [3:0]                     cfg_wcska_pinmux                        ; // clock skew adjust for pinmux
wire [3:0]                     cfg_wcska_qspi_co                       ; // clock skew adjust for global reg

// Bus Repeater Signals  output from Wishbone Interface
wire [3:0]                     cfg_wcska_riscv_rp                      ; // clock skew adjust for riscv
wire [3:0]                     cfg_wcska_uart_rp                       ; // clock skew adjust for uart
wire [3:0]                     cfg_wcska_qspi_rp                       ; // clock skew adjust for spi
wire [3:0]                     cfg_wcska_pinmux_rp                     ; // clock skew adjust for pinmux
wire [3:0]                     cfg_wcska_qspi_co_rp                    ; // clock skew adjust for global reg

wire [31:0]                    irq_lines_rp                           ; // Repeater
wire                           soft_irq_rp                            ; // Repeater

wire                           wbd_clk_risc_rp                        ;
wire                           wbd_clk_qspi_rp                        ;
wire                           wbd_clk_uart_rp                        ;
wire                           wbd_clk_pinmux_rp                      ;
wire                           wbd_clk_pinmux_skew                    ;

// Progammable Clock Skew inserted signals
wire                           wbd_clk_wi_skew                        ; // clock for wishbone interconnect with clock skew
wire                           wbd_clk_riscv_skew                     ; // clock for riscv with clock skew
wire                           wbd_clk_uart_skew                      ; // clock for uart with clock skew
wire                           wbd_clk_spi_skew                       ; // clock for spi with clock skew
wire                           wbd_clk_glbl_skew                      ; // clock for global reg with clock skew
wire                           wbd_clk_wh_skew                        ; // clock for global reg


wire [31:0]                    spi_debug                              ;
wire [31:0]                    pinmux_debug                           ;
wire                           dbg_clk_mon                            ; // clock monitoring port
wire [63:0]                    riscv_debug                            ;

// SFLASH I/F
wire                           sflash_sck                             ;
wire [3:0]                     sflash_ss                              ;
wire [3:0]                     sflash_oen                             ;
wire [3:0]                     sflash_do                              ;
wire [3:0]                     sflash_di                              ;

// SSRAM I/F
//wire                         ssram_sck                              ;
//wire                         ssram_ss                               ;
//wire                         ssram_oen                              ;
//wire [3:0]                   ssram_do                               ;
//wire [3:0]                   ssram_di                               ;

// USB I/F
wire                           usb_dp_o                               ;
wire                           usb_dn_o                               ;
wire                           usb_oen                                ;
wire                           usb_dp_i                               ;
wire                           usb_dn_i                               ;

// UART I/F
wire       [1:0]               uart_txd                               ;
wire       [1:0]               uart_rxd                               ;

// I2CM I/F
wire                           i2cm_clk_o                             ;
wire                           i2cm_clk_i                             ;
wire                           i2cm_clk_oen                           ;
wire                           i2cm_data_oen                          ;
wire                           i2cm_data_o                            ;
wire                           i2cm_data_i                            ;

// SPI MASTER
wire                           spim_sck                               ;
wire                           spim_ss                                ;
wire                           spim_miso                              ;
wire                           spim_mosi                              ;

wire [7:0]                     sar2dac                                ;
wire                           analog_dac_out                         ;
wire                           pulse1m_mclk                           ;
wire                           h_reset_n                              ;

`ifndef SCR1_TCM_MEM
// SRAM-0 PORT-0 - DMEM I/F
wire                           sram0_clk0                             ; // CLK
wire                           sram0_csb0                             ; // CS#
wire                           sram0_web0                             ; // WE#
wire   [8:0]                   sram0_addr0                            ; // Address
wire   [3:0]                   sram0_wmask0                           ; // WMASK#
wire   [31:0]                  sram0_din0                             ; // Write Data
wire   [31:0]                  sram0_dout0                            ; // Read Data

// SRAM-0 PORT-1, IMEM I/F
wire                           sram0_clk1                             ; // CLK
wire                           sram0_csb1                             ; // CS#
wire  [8:0]                    sram0_addr1                            ; // Address
wire  [31:0]                   sram0_dout1                            ; // Read Data

// SRAM-1 PORT-0 - DMEM I/F
wire                           sram1_clk0                             ; // CLK
wire                           sram1_csb0                             ; // CS#
wire                           sram1_web0                             ; // WE#
wire   [8:0]                   sram1_addr0                            ; // Address
wire   [3:0]                   sram1_wmask0                           ; // WMASK#
wire   [31:0]                  sram1_din0                             ; // Write Data
wire   [31:0]                  sram1_dout0                            ; // Read Data

// SRAM-1 PORT-1, IMEM I/F
wire                           sram1_clk1                             ; // CLK
wire                           sram1_csb1                             ; // CS#
wire  [8:0]                    sram1_addr1                            ; // Address
wire  [31:0]                   sram1_dout1                            ; // Read Data

`endif

// SPIM I/F
wire                           sspim_sck                              ; // clock out
wire                           sspim_so                               ; // serial data out
wire                           sspim_si                               ; // serial data in
wire    [3:0]                  sspim_ssn                              ; // cs_n

// SPIS I/F
wire                           sspis_sck                              ; // clock out
wire                           sspis_so                               ; // serial data out
wire                           sspis_si                               ; // serial data in
wire                           sspis_ssn                              ; // cs_n


wire                           usb_intr_o                             ;
wire                           i2cm_intr_o                            ;

//------------------------------------------------------------
// AES Integration local decleration
//------------------------------------------------------------
wire                           cpu_clk_aes                            ;
wire [3:0]                     cfg_ccska_aes                          ;
wire [3:0]                     cfg_ccska_aes_rp                       ;
wire                           aes_dmem_req                           ;
wire                           aes_dmem_cmd                           ;
wire [1:0]                     aes_dmem_width                         ;
wire [6:0]                     aes_dmem_addr                          ;
wire [31:0]                    aes_dmem_wdata                         ;
wire                           aes_dmem_req_ack                       ;
wire [31:0]                    aes_dmem_rdata                         ;
wire [1:0]                     aes_dmem_resp                          ;

//------------------------------------------------------------
// FPU Integration local decleration
//------------------------------------------------------------
wire                           cpu_clk_fpu                            ;
wire [3:0]                     cfg_ccska_fpu                          ;
wire [3:0]                     cfg_ccska_fpu_rp                       ;
wire                           fpu_dmem_req                           ;
wire                           fpu_dmem_cmd                           ;
wire [1:0]                     fpu_dmem_width                         ;
wire [4:0]                     fpu_dmem_addr                          ;
wire [31:0]                    fpu_dmem_wdata                         ;
wire                           fpu_dmem_req_ack                       ;
wire [31:0]                    fpu_dmem_rdata                         ;
wire [1:0]                     fpu_dmem_resp                          ;

//----------------------------------------------------------------
//  UART Master I/F
//  -------------------------------------------------------------
wire                           uartm_rxd                              ;
wire                           uartm_txd                              ;

//----------------------------------------------------------------
//  Digital PLL I/F
//  -------------------------------------------------------------
wire                           cfg_pll_enb                            ; // Enable PLL
wire [4:0]                     cfg_pll_fed_div                        ; // PLL feedback division ratio
wire                           cfg_dco_mode                           ; // Run PLL in DCO mode
wire [25:0]                    cfg_dc_trim                            ; // External trim for DCO mode
wire                           pll_ref_clk                            ; // Input oscillator to match
wire [1:0]                     pll_clk_out                            ; // Two 90 degree clock phases

wire [3:0]                     spi_csn                                ;
wire                           xtal_clk                               ;
wire                           e_reset_n                              ;
wire                           p_reset_n                              ;
wire                           s_reset_n                              ;
wire                           cfg_strap_pad_ctrl                     ;

wire                           e_reset_n_rp                           ;
wire                           p_reset_n_rp                           ;
wire                           s_reset_n_rp                           ;
wire                           cfg_strap_pad_ctrl_rp                  ;
//----------------------------------------------------------------------
// DAC Config
//----------------------------------------------------------------------
wire [7:0]                     cfg_dac0_mux_sel                       ;
wire [7:0]                     cfg_dac1_mux_sel                       ;
wire [7:0]                     cfg_dac2_mux_sel                       ;
wire [7:0]                     cfg_dac3_mux_sel                       ;

//---------------------------------------------------------------------
// Strap
//---------------------------------------------------------------------
wire [31:0]                    system_strap                           ;
wire [31:0]                    strap_sticky                           ;
wire [1:0]                     strap_uartm                            ;

wire [31:0]                    system_strap_rp                        ;
wire [31:0]                    strap_sticky_rp                        ;
wire [1:0]                     strap_uartm_rp                         ;

wire [1:0]  strap_qspi_flash       = system_strap[`STRAP_QSPI_FLASH];
wire        strap_qspi_sram        = system_strap[`STRAP_QSPI_SRAM];
wire        strap_qspi_pre_sram    = system_strap[`STRAP_QSPI_PRE_SRAM];
wire        strap_qspi_init_bypass = system_strap[`STRAP_QSPI_INIT_BYPASS];


//--------------------------------------------------------------------------
// Pinmux Risc core config
// -------------------------------------------------------------------------
wire [15:0]                    cfg_riscv_ctrl;
wire [3:0]                     cfg_riscv_sram_lphase   = cfg_riscv_ctrl[3:0];
wire [2:0]                     cfg_riscv_cache_ctrl    = cfg_riscv_ctrl[6:4];
wire [1:0]                     cfg_riscv_debug_sel     = cfg_riscv_ctrl[9:8];
wire                           cfg_bypass_icache       = cfg_riscv_ctrl[10];
wire                           cfg_bypass_dcache       = cfg_riscv_ctrl[11];

/////////////////////////////////////////////////////////
// System/WB Clock Skew Ctrl
////////////////////////////////////////////////////////

assign cfg_wcska_wi          = cfg_clk_skew_ctrl1[3:0];
assign cfg_wcska_wh          = cfg_clk_skew_ctrl1[7:4];
assign cfg_wcska_riscv       = cfg_clk_skew_ctrl1[11:8];
assign cfg_wcska_qspi        = cfg_clk_skew_ctrl1[15:12];
assign cfg_wcska_uart        = cfg_clk_skew_ctrl1[19:16];
assign cfg_wcska_pinmux      = cfg_clk_skew_ctrl1[23:20];
assign cfg_wcska_qspi_co     = cfg_clk_skew_ctrl1[27:24];

/////////////////////////////////////////////////////////
// RISCV Clock skew control
/////////////////////////////////////////////////////////
wire [3:0] cfg_ccska_riscv_intf_rp  ;
wire [3:0] cfg_ccska_riscv_icon_rp  ;
wire [3:0] cfg_ccska_riscv_core0_rp ;
wire [3:0] cfg_ccska_riscv_core1_rp ;
wire [3:0] cfg_ccska_riscv_core2_rp ;
wire [3:0] cfg_ccska_riscv_core3_rp ;

wire [3:0]   cfg_ccska_riscv_intf   = cfg_clk_skew_ctrl2[3:0];
wire [3:0]   cfg_ccska_riscv_icon   = cfg_clk_skew_ctrl2[7:4];
wire [3:0]   cfg_ccska_riscv_core0  = cfg_clk_skew_ctrl2[11:8];
wire [3:0]   cfg_ccska_riscv_core1  = cfg_clk_skew_ctrl2[15:12];
wire [3:0]   cfg_ccska_riscv_core2  = cfg_clk_skew_ctrl2[19:16];
wire [3:0]   cfg_ccska_riscv_core3  = cfg_clk_skew_ctrl2[23:20];
assign       cfg_ccska_aes          = cfg_clk_skew_ctrl2[27:24];
assign       cfg_ccska_fpu          = cfg_clk_skew_ctrl2[31:28];

assign la_data_out[127:0]    = {pinmux_debug,spi_debug,riscv_debug};

wire   int_pll_clock       = pll_clk_out[0];

//-------------------------------------
// cpu clock repeater mapping
//-------------------------------------
wire [2:0] cpu_clk_rp;

wire [1:0] cpu_clk_rp_risc   = cpu_clk_rp[1:0];
wire       cpu_clk_rp_pinmux = cpu_clk_rp[2];


/***********************************************
 Wishbone HOST
*************************************************/

wb_host u_wb_host(
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
          .user_clock1             (wb_clk_i                ),
          .user_clock2             (user_clock2             ),
          .int_pll_clock           (int_pll_clock           ),

          .cpu_clk                 (cpu_clk                 ),

       // to/from Pinmux
          .xtal_clk                (xtal_clk                ),
	      .e_reset_n               (e_reset_n               ),  // external reset
	      .p_reset_n               (p_reset_n               ),  // power-on reset
          .s_reset_n               (s_reset_n               ),  // soft reset
          .cfg_strap_pad_ctrl      (cfg_strap_pad_ctrl      ),
	      .system_strap            (system_strap            ),
	      .strap_sticky            (strap_sticky_rp         ),
	      .strap_uartm             (strap_uartm_rp          ),

          .wbd_int_rst_n           (wbd_int_rst_n           ),
          .wbd_pll_rst_n           (wbd_pll_rst_n           ),

    // Master Port
          .wbm_rst_i               (wb_rst_i                ),  
          .wbm_clk_i               (wb_clk_i                ),  
          .wbm_cyc_i               (wbs_cyc_i               ),  
          .wbm_stb_i               (wbs_stb_i               ),  
          .wbm_adr_i               (wbs_adr_i               ),  
          .wbm_we_i                (wbs_we_i                ),  
          .wbm_dat_i               (wbs_dat_i               ),  
          .wbm_sel_i               (wbs_sel_i               ),  
          .wbm_dat_o               (wbs_dat_o               ),  
          .wbm_ack_o               (wbs_ack_o               ),  
          .wbm_err_o               (                        ),  

    // Clock Skeq Adjust
          .wbd_clk_int             (wbd_clk_int             ),
          .wbd_clk_wh              (wbd_clk_wh              ),  
          .cfg_cska_wh             (cfg_wcska_wh             ),

    // Slave Port
          .wbs_clk_out             (wbd_clk_int             ),
          .wbs_clk_i               (wbd_clk_wh              ),  
          .wbs_cyc_o               (wbd_int_cyc_i           ),  
          .wbs_stb_o               (wbd_int_stb_i           ),  
          .wbs_adr_o               (wbd_int_adr_i           ),  
          .wbs_we_o                (wbd_int_we_i            ),  
          .wbs_dat_o               (wbd_int_dat_i           ),  
          .wbs_sel_o               (wbd_int_sel_i           ),  
          .wbs_dat_i               (wbd_int_dat_o           ),  
          .wbs_ack_i               (wbd_int_ack_o           ),  
          .wbs_err_i               (wbd_int_err_o           ),  

          .cfg_clk_skew_ctrl1      (cfg_clk_skew_ctrl1      ),
          .cfg_clk_skew_ctrl2      (cfg_clk_skew_ctrl2      ),

          .la_data_in              (la_data_in[17:0]        ),

          .uartm_rxd               (uartm_rxd               ),
          .uartm_txd               (uartm_txd               ),

          .sclk                    (sspis_sck               ),
          .ssn                     (sspis_ssn               ),
          .sdin                    (sspis_si                ),
          .sdout                   (sspis_so                ),
          .sdout_oen               (                        )


    );

/****************************************************************
  Digital PLL
*****************************************************************/

// This rtl/gds picked from efabless caravel project 
dg_pll   u_pll(
`ifdef USE_POWER_PINS
    .VPWR                           (vccd1                  ),
    .VGND                           (vssd1                  ),
`endif
    .resetb                         (wbd_pll_rst_n          ), 
    .enable                         (cfg_pll_enb            ), 
    .div                            (cfg_pll_fed_div        ), 
    .dco                            (cfg_dco_mode           ), 
    .ext_trim                       (cfg_dc_trim            ),
    .osc                            (pll_ref_clk            ), 
    .clockp                         (pll_clk_out            ) 
    );


//------------------------------------------------------------------------------
// RISC V Core instance
//------------------------------------------------------------------------------
ycr4_top_wb u_riscv_top (
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
          .wbd_clk_int             (wbd_clk_risc_rp            ), 
          .cfg_wcska_riscv_intf    (cfg_wcska_riscv_rp         ), 
          .wbd_clk_skew            (wbd_clk_riscv_skew         ),

    // Reset
          .pwrup_rst_n             (wbd_int_rst_n           ),
          .rst_n                   (wbd_int_rst_n           ),
          .cpu_intf_rst_n          (cpu_intf_rst_n          ),
          .cpu_core_rst_n          (cpu_core_rst_n          ),
          .riscv_debug             (riscv_debug             ),
	  .core_debug_sel          (cfg_riscv_debug_sel     ),
	  .cfg_sram_lphase         (cfg_riscv_sram_lphase   ),
	  .cfg_cache_ctrl          (cfg_riscv_cache_ctrl    ),
	  .cfg_bypass_icache       (cfg_bypass_icache       ),
	  .cfg_bypass_dcache       (cfg_bypass_dcache       ),

    // Clock
          .core_clk_int            (cpu_clk_rp_risc            ),
          .cfg_ccska_riscv_intf    (cfg_ccska_riscv_intf_rp    ),
          .cfg_ccska_riscv_icon    (cfg_ccska_riscv_icon_rp    ),
          .cfg_ccska_riscv_core0   (cfg_ccska_riscv_core0_rp   ),
          .cfg_ccska_riscv_core1   (cfg_ccska_riscv_core1_rp   ),
          .cfg_ccska_riscv_core2   (cfg_ccska_riscv_core2_rp   ),
          .cfg_ccska_riscv_core3   (cfg_ccska_riscv_core3_rp   ),

          .rtc_clk                 (rtc_clk                    ),


    // IRQ
          .irq_lines               (irq_lines_rp               ), 
          .soft_irq                (soft_irq_rp                ), // TODO - Interrupts

    // DFT
    //    .test_mode               (1'b0                       ), // Moved inside IP
    //    .test_rst_n              (1'b1                       ), // Moved inside IP

`ifndef SCR1_TCM_MEM
    // SRAM-0 PORT-0
          .sram0_clk0             (sram0_clk0                  ),
          .sram0_csb0             (sram0_csb0                  ),
          .sram0_web0             (sram0_web0                  ),
          .sram0_addr0            (sram0_addr0                 ),
          .sram0_wmask0           (sram0_wmask0                ),
          .sram0_din0             (sram0_din0                  ),
          .sram0_dout0            (sram0_dout0                 ),
    
    // SRAM-0 PORT-0
          .sram0_clk1             (sram0_clk1                   ),
          .sram0_csb1             (sram0_csb1                   ),
          .sram0_addr1            (sram0_addr1                  ),
          .sram0_dout1            (sram0_dout1                  ),

  //  // SRAM-1 PORT-0
  //      .sram1_clk0             (sram1_clk0                   ),
  //      .sram1_csb0             (sram1_csb0                   ),
  //      .sram1_web0             (sram1_web0                   ),
  //      .sram1_addr0            (sram1_addr0                  ),
  //      .sram1_wmask0           (sram1_wmask0                 ),
  //      .sram1_din0             (sram1_din0                   ),
  //      .sram1_dout0            (sram1_dout0                  ),
  //  
  //  // SRAM PORT-0
  //      .sram1_clk1             (sram1_clk1                   ),
  //      .sram1_csb1             (sram1_csb1                   ),
  //      .sram1_addr1            (sram1_addr1                  ),
  //      .sram1_dout1            (sram1_dout1                  ),
`endif
    
          .wb_rst_n                (wbd_int_rst_n           ),
          .wb_clk                  (wbd_clk_riscv_skew      ),

    // Instruction cache memory interface
          .wb_icache_stb_o         (wbd_riscv_icache_stb_i  ),
          .wb_icache_adr_o         (wbd_riscv_icache_adr_i  ),
          .wb_icache_we_o          (wbd_riscv_icache_we_i   ), 
          .wb_icache_sel_o         (wbd_riscv_icache_sel_i  ),
          .wb_icache_bl_o          (wbd_riscv_icache_bl_i   ),
          .wb_icache_bry_o         (wbd_riscv_icache_bry_i  ),
          .wb_icache_dat_i         (wbd_riscv_icache_dat_o  ),
          .wb_icache_ack_i         (wbd_riscv_icache_ack_o  ),
          .wb_icache_lack_i        (wbd_riscv_icache_lack_o ),
          .wb_icache_err_i         (wbd_riscv_icache_err_o  ),

          .icache_mem_clk0    (icache_mem_clk0              ), // CLK
          .icache_mem_csb0    (icache_mem_csb0              ), // CS#
          .icache_mem_web0    (icache_mem_web0              ), // WE#
          .icache_mem_addr0   (icache_mem_addr0             ), // Address
          .icache_mem_wmask0  (icache_mem_wmask0            ), // WMASK#
          .icache_mem_din0    (icache_mem_din0              ), // Write Data
//        .icache_mem_dout0   (icache_mem_dout0             ), // Read Data
                                
                                
          .icache_mem_clk1    (icache_mem_clk1              ), // CLK
          .icache_mem_csb1    (icache_mem_csb1              ), // CS#
          .icache_mem_addr1   (icache_mem_addr1             ), // Address
          .icache_mem_dout1   (icache_mem_dout1             ), // Read Data

    // Data cache memory interface
          .wb_dcache_stb_o         (wbd_riscv_dcache_stb_i  ),
          .wb_dcache_adr_o         (wbd_riscv_dcache_adr_i  ),
          .wb_dcache_we_o          (wbd_riscv_dcache_we_i   ), 
          .wb_dcache_dat_o         (wbd_riscv_dcache_dat_i  ),
          .wb_dcache_sel_o         (wbd_riscv_dcache_sel_i  ),
          .wb_dcache_bl_o          (wbd_riscv_dcache_bl_i   ),
          .wb_dcache_bry_o         (wbd_riscv_dcache_bry_i  ),
          .wb_dcache_dat_i         (wbd_riscv_dcache_dat_o  ),
          .wb_dcache_ack_i         (wbd_riscv_dcache_ack_o  ),
          .wb_dcache_lack_i        (wbd_riscv_dcache_lack_o ),
          .wb_dcache_err_i         (wbd_riscv_dcache_err_o  ),

          .dcache_mem_clk0    (dcache_mem_clk0              ), // CLK
          .dcache_mem_csb0    (dcache_mem_csb0              ), // CS#
          .dcache_mem_web0    (dcache_mem_web0              ), // WE#
          .dcache_mem_addr0   (dcache_mem_addr0             ), // Address
          .dcache_mem_wmask0  (dcache_mem_wmask0            ), // WMASK#
          .dcache_mem_din0    (dcache_mem_din0              ), // Write Data
          .dcache_mem_dout0   (dcache_mem_dout0             ), // Read Data
                                
                                
          .dcache_mem_clk1    (dcache_mem_clk1              ), // CLK
          .dcache_mem_csb1    (dcache_mem_csb1              ), // CS#
          .dcache_mem_addr1   (dcache_mem_addr1             ), // Address
          .dcache_mem_dout1   (dcache_mem_dout1             ), // Read Data


    // Data memory interface
          .wbd_dmem_stb_o          (wbd_riscv_dmem_stb_i    ),
          .wbd_dmem_adr_o          (wbd_riscv_dmem_adr_i    ),
          .wbd_dmem_we_o           (wbd_riscv_dmem_we_i     ), 
          .wbd_dmem_dat_o          (wbd_riscv_dmem_dat_i    ),
          .wbd_dmem_sel_o          (wbd_riscv_dmem_sel_i    ),
          .wbd_dmem_bl_o           (wbd_riscv_dmem_bl_i     ),
          .wbd_dmem_bry_o          (wbd_riscv_dmem_bry_i    ),
          .wbd_dmem_dat_i          (wbd_riscv_dmem_dat_o    ),
          .wbd_dmem_ack_i          (wbd_riscv_dmem_ack_o    ),
          .wbd_dmem_lack_i         (wbd_riscv_dmem_lack_o   ),
          .wbd_dmem_err_i          (wbd_riscv_dmem_err_o    ) 
);

`ifndef SCR1_TCM_MEM
sky130_sram_2kbyte_1rw1r_32x512_8 u_tsram0_2kb(
`ifdef USE_POWER_PINS
          .vccd1              (vccd1                        ),// area 1 1.8V supply
          .vssd1              (vssd1                        ),// area 1 digital ground
`endif
// Port 0: RW
          .clk0               (sram0_clk0                   ),
          .csb0               (sram0_csb0                   ),
          .web0               (sram0_web0                   ),
          .wmask0             (sram0_wmask0                 ),
          .addr0              (sram0_addr0                  ),
          .din0               (sram0_din0                   ),
          .dout0              (sram0_dout0                  ),
// Port 1: R
          .clk1               (sram0_clk1                   ),
          .csb1               (sram0_csb1                   ),
          .addr1              (sram0_addr1                  ),
          .dout1              (sram0_dout1                  )
  );

/***
sky130_sram_2kbyte_1rw1r_32x512_8 u_tsram1_2kb(
`ifdef USE_POWER_PINS
          .vccd1              (vccd1                        ),// User area 1 1.8V supply
          .vssd1              (vssd1                        ),// User area 1 digital ground
`endif
// Port 0: RW
          .clk0               (sram1_clk0                   ),
          .csb0               (sram1_csb0                   ),
          .web0               (sram1_web0                   ),
          .wmask0             (sram1_wmask0                 ),
          .addr0              (sram1_addr0                  ),
          .din0               (sram1_din0                   ),
          .dout0              (sram1_dout0                  ),
// Port 1: R
          .clk1               (sram1_clk1                   ),
          .csb1               (sram1_csb1                   ),
          .addr1              (sram1_addr1                  ),
          .dout1              (sram1_dout1                  )
  );
***/
`endif


sky130_sram_2kbyte_1rw1r_32x512_8 u_icache_2kb(
`ifdef USE_POWER_PINS
          .vccd1              (vccd1                        ),// User area 1 1.8V supply
          .vssd1              (vssd1                        ),// User area 1 digital ground
`endif
// Port 0: RW
          .clk0               (icache_mem_clk0              ),
          .csb0               (icache_mem_csb0              ),
          .web0               (icache_mem_web0              ),
          .wmask0             (icache_mem_wmask0            ),
          .addr0              (icache_mem_addr0             ),
          .din0               (icache_mem_din0              ),
          .dout0              (                             ),
// Port 1: R
          .clk1               (icache_mem_clk1              ),
          .csb1               (icache_mem_csb1              ),
          .addr1              (icache_mem_addr1             ),
          .dout1              (icache_mem_dout1             )
  );

sky130_sram_2kbyte_1rw1r_32x512_8 u_dcache_2kb(
`ifdef USE_POWER_PINS
          .vccd1              (vccd1                        ),// User area 1 1.8V supply
          .vssd1              (vssd1                        ),// User area 1 digital ground
`endif
// Port 0: RW
          .clk0               (dcache_mem_clk0              ),
          .csb0               (dcache_mem_csb0              ),
          .web0               (dcache_mem_web0              ),
          .wmask0             (dcache_mem_wmask0            ),
          .addr0              (dcache_mem_addr0             ),
          .din0               (dcache_mem_din0              ),
          .dout0              (dcache_mem_dout0             ),
// Port 1: R
          .clk1               (dcache_mem_clk1              ),
          .csb1               (dcache_mem_csb1              ),
          .addr1              (dcache_mem_addr1             ),
          .dout1              (dcache_mem_dout1             )
  );


/*********************************************************
* SPI Master
* This is implementation of an SPI master that is controlled via an AXI bus                                                  . 
* It has FIFOs for transmitting and receiving data. 
* It supports both the normal SPI mode and QPI mode with 4 data lines.
* *******************************************************/

qspim_top
#(
`ifndef SYNTHESIS
    .WB_WIDTH  (WB_WIDTH                                    )
`endif
) u_qspi_master
(
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
          .mclk                    (wbd_clk_spi             ),
          .rst_n                   (qspim_rst_n             ),

          .strap_flash             (strap_qspi_flash        ),
          .strap_pre_sram          (strap_qspi_pre_sram     ),
          .strap_sram              (strap_qspi_sram         ),
          .cfg_init_bypass         (strap_qspi_init_bypass  ),

    // Clock Skew Adjust
          .cfg_cska_sp_co          (cfg_wcska_qspi_co_rp     ),
          .cfg_cska_spi            (cfg_wcska_qspi_rp        ),
          .wbd_clk_int             (wbd_clk_qspi_rp         ),
          .wbd_clk_spi             (wbd_clk_spi             ),

          .wbd_stb_i               (wbd_spim_stb_o          ),
          .wbd_adr_i               (wbd_spim_adr_o          ),
          .wbd_we_i                (wbd_spim_we_o           ), 
          .wbd_dat_i               (wbd_spim_dat_o          ),
          .wbd_sel_i               (wbd_spim_sel_o          ),
          .wbd_bl_i                (wbd_spim_bl_o           ),
          .wbd_bry_i               (wbd_spim_bry_o          ),
          .wbd_dat_o               (wbd_spim_dat_i          ),
          .wbd_ack_o               (wbd_spim_ack_i          ),
          .wbd_lack_o              (wbd_spim_lack_i         ),
          .wbd_err_o               (wbd_spim_err_i          ),

          .spi_debug               (spi_debug               ),

    // Pad Interface
          .spi_sdi                 (sflash_di               ),
          .spi_clk                 (sflash_sck              ),
          .spi_csn                 (spi_csn                 ),
          .spi_sdo                 (sflash_do               ),
          .spi_oen                 (sflash_oen              )

);


wb_interconnect  #(
	`ifndef SYNTHESIS
          .CH_CLK_WD           (7                      ),
	      .CH_DATA_WD          (154                     )
        `endif
	) u_intercon (
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
	  .ch_clk_in               ({
                                     cpu_clk,
                                     cpu_clk,
                                     cpu_clk,
                                     wbd_clk_int, 
                                     wbd_clk_int, 
                                     wbd_clk_int, 
                                     wbd_clk_int}                  ),
	  .ch_clk_out              ({
                                     cpu_clk_rp,
                                     wbd_clk_pinmux_rp, 
                                     wbd_clk_uart_rp, 
                                     wbd_clk_qspi_rp, 
                                     wbd_clk_risc_rp}              ),
	  .ch_data_in              ({
                                  cfg_ccska_fpu[3:0],
                                  cfg_ccska_aes[3:0],
                                  strap_sticky[31:0],
                                  strap_uartm[1:0],
                                  system_strap[31:0],
                                  p_reset_n,
                                  e_reset_n,
                                  cfg_strap_pad_ctrl,
			 
	                              soft_irq,
			                      irq_lines[31:0],

			                      cfg_ccska_riscv_core3[3:0],
			                      cfg_ccska_riscv_core2[3:0],
			                      cfg_ccska_riscv_core1[3:0],
			                      cfg_ccska_riscv_core0[3:0],
			                      cfg_ccska_riscv_icon[3:0],
			                      cfg_ccska_riscv_intf[3:0],

			                      cfg_wcska_qspi_co[3:0],
		                          cfg_wcska_pinmux[3:0],
			                      cfg_wcska_uart[3:0],
		                          cfg_wcska_qspi[3:0],
                                  cfg_wcska_riscv[3:0]
			             }                             ),
	  .ch_data_out             ({
			                      cfg_ccska_fpu_rp[3:0],
			                      cfg_ccska_aes_rp[3:0],
                                  strap_sticky_rp[31:0],
                                  strap_uartm_rp[1:0],
                                  system_strap_rp[31:0],
                                  p_reset_n_rp,
                                  e_reset_n_rp,
                                  cfg_strap_pad_ctrl_rp,

	                              soft_irq_rp,
			                      irq_lines_rp[31:0],

			                      cfg_ccska_riscv_core3_rp[3:0],
			                      cfg_ccska_riscv_core2_rp[3:0],
			                      cfg_ccska_riscv_core1_rp[3:0],
			                      cfg_ccska_riscv_core0_rp[3:0],
			                      cfg_ccska_riscv_icon_rp[3:0],
			                      cfg_ccska_riscv_intf_rp[3:0],

			                      cfg_wcska_qspi_co_rp[3:0],
		                          cfg_wcska_pinmux_rp[3:0],
			                      cfg_wcska_uart_rp[3:0],
		                          cfg_wcska_qspi_rp[3:0],
                                  cfg_wcska_riscv_rp[3:0]
                               } ),
     // Clock Skew adjust
	  .wbd_clk_int                 (wbd_clk_int             ), 
	  .cfg_cska_wi                 (cfg_wcska_wi            ), 
	  .wbd_clk_wi                  (wbd_clk_wi_skew         ),

          .clk_i                   (wbd_clk_wi_skew         ), 
          .rst_n                   (wbd_int_rst_n           ),

         // Master 0 Interface
          .m0_wbd_dat_i            (wbd_int_dat_i           ),
          .m0_wbd_adr_i            (wbd_int_adr_i           ),
          .m0_wbd_sel_i            (wbd_int_sel_i           ),
          .m0_wbd_we_i             (wbd_int_we_i            ),
          .m0_wbd_cyc_i            (wbd_int_cyc_i           ),
          .m0_wbd_stb_i            (wbd_int_stb_i           ),
          .m0_wbd_dat_o            (wbd_int_dat_o           ),
          .m0_wbd_ack_o            (wbd_int_ack_o           ),
          .m0_wbd_err_o            (wbd_int_err_o           ),
         
         // Master 1 Interface
          .m1_wbd_dat_i            (wbd_riscv_dmem_dat_i    ),
          .m1_wbd_adr_i            (wbd_riscv_dmem_adr_i    ),
          .m1_wbd_sel_i            (wbd_riscv_dmem_sel_i    ),
          .m1_wbd_bl_i             (wbd_riscv_dmem_bl_i    ),
          .m1_wbd_bry_i            (wbd_riscv_dmem_bry_i    ),
          .m1_wbd_we_i             (wbd_riscv_dmem_we_i     ),
          .m1_wbd_cyc_i            (wbd_riscv_dmem_stb_i    ),
          .m1_wbd_stb_i            (wbd_riscv_dmem_stb_i    ),
          .m1_wbd_dat_o            (wbd_riscv_dmem_dat_o    ),
          .m1_wbd_ack_o            (wbd_riscv_dmem_ack_o    ),
          .m1_wbd_lack_o           (wbd_riscv_dmem_lack_o   ),
          .m1_wbd_err_o            (wbd_riscv_dmem_err_o    ),
         
         // Master 2 Interface
          .m2_wbd_dat_i            (wbd_riscv_dcache_dat_i  ),
          .m2_wbd_adr_i            (wbd_riscv_dcache_adr_i  ),
          .m2_wbd_sel_i            (wbd_riscv_dcache_sel_i  ),
          .m2_wbd_bl_i             (wbd_riscv_dcache_bl_i   ),
          .m2_wbd_bry_i            (wbd_riscv_dcache_bry_i  ),
          .m2_wbd_we_i             (wbd_riscv_dcache_we_i   ),
          .m2_wbd_cyc_i            (wbd_riscv_dcache_stb_i  ),
          .m2_wbd_stb_i            (wbd_riscv_dcache_stb_i  ),
          .m2_wbd_dat_o            (wbd_riscv_dcache_dat_o  ),
          .m2_wbd_ack_o            (wbd_riscv_dcache_ack_o  ),
          .m2_wbd_lack_o           (wbd_riscv_dcache_lack_o ),
          .m2_wbd_err_o            (wbd_riscv_dcache_err_o  ),

         // Master 3 Interface
          .m3_wbd_adr_i            (wbd_riscv_icache_adr_i  ),
          .m3_wbd_sel_i            (wbd_riscv_icache_sel_i  ),
          .m3_wbd_bl_i             (wbd_riscv_icache_bl_i   ),
          .m3_wbd_bry_i            (wbd_riscv_icache_bry_i  ),
          .m3_wbd_we_i             (wbd_riscv_icache_we_i   ),
          .m3_wbd_cyc_i            (wbd_riscv_icache_stb_i  ),
          .m3_wbd_stb_i            (wbd_riscv_icache_stb_i  ),
          .m3_wbd_dat_o            (wbd_riscv_icache_dat_o  ),
          .m3_wbd_ack_o            (wbd_riscv_icache_ack_o  ),
          .m3_wbd_lack_o           (wbd_riscv_icache_lack_o ),
          .m3_wbd_err_o            (wbd_riscv_icache_err_o  ),
         
         
         // Slave 0 Interface
       // .s0_wbd_err_i            (1'b0                    ), - Moved inside IP
          .s0_wbd_dat_i            (wbd_spim_dat_i          ),
          .s0_wbd_ack_i            (wbd_spim_ack_i          ),
          .s0_wbd_lack_i           (wbd_spim_lack_i         ),
          .s0_wbd_dat_o            (wbd_spim_dat_o          ),
          .s0_wbd_adr_o            (wbd_spim_adr_o          ),
          .s0_wbd_bry_o            (wbd_spim_bry_o          ),
          .s0_wbd_bl_o             (wbd_spim_bl_o           ),
          .s0_wbd_sel_o            (wbd_spim_sel_o          ),
          .s0_wbd_we_o             (wbd_spim_we_o           ),  
          .s0_wbd_cyc_o            (wbd_spim_cyc_o          ),
          .s0_wbd_stb_o            (wbd_spim_stb_o          ),
         
         // Slave 1 Interface
       // .s1_wbd_err_i            (1'b0                    ), - Moved inside IP
          .s1_wbd_dat_i            (wbd_uart_dat_i          ),
          .s1_wbd_ack_i            (wbd_uart_ack_i          ),
          .s1_wbd_dat_o            (wbd_uart_dat_o          ),
          .s1_wbd_adr_o            (wbd_uart_adr_o          ),
          .s1_wbd_sel_o            (wbd_uart_sel_o          ),
          .s1_wbd_we_o             (wbd_uart_we_o           ),  
          .s1_wbd_cyc_o            (wbd_uart_cyc_o          ),
          .s1_wbd_stb_o            (wbd_uart_stb_o          ),
         
         // Slave 2 Interface
       // .s2_wbd_err_i            (1'b0                    ), - Moved inside IP
          .s2_wbd_dat_i            (wbd_glbl_dat_i          ),
          .s2_wbd_ack_i            (wbd_glbl_ack_i          ),
          .s2_wbd_dat_o            (wbd_glbl_dat_o          ),
          .s2_wbd_adr_o            (wbd_glbl_adr_o          ),
          .s2_wbd_sel_o            (wbd_glbl_sel_o          ),
          .s2_wbd_we_o             (wbd_glbl_we_o           ),  
          .s2_wbd_cyc_o            (wbd_glbl_cyc_o          ),
          .s2_wbd_stb_o            (wbd_glbl_stb_o          )


	);


uart_i2c_usb_spi_top   u_uart_i2c_usb_spi (
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
          .wbd_clk_int             (wbd_clk_uart_rp         ), 
          .cfg_cska_uart           (cfg_wcska_uart_rp        ), 
          .wbd_clk_uart            (wbd_clk_uart_skew       ),

          .uart_rstn               (uart_rst_n              ), // uart reset
          .i2c_rstn                (i2c_rst_n               ), // i2c reset
          .usb_rstn                (usb_rst_n               ), // USB reset
          .spi_rstn                (sspim_rst_n             ), // SPI reset
          .app_clk                 (wbd_clk_uart_skew       ),
	      .usb_clk                 (usb_clk                 ),

        // Reg Bus Interface Signal
          .reg_cs                  (wbd_uart_stb_o          ),
          .reg_wr                  (wbd_uart_we_o           ),
          .reg_addr                (wbd_uart_adr_o[8:0]     ),
          .reg_wdata               (wbd_uart_dat_o          ),
          .reg_be                  (wbd_uart_sel_o          ),

       // Outputs
          .reg_rdata               (wbd_uart_dat_i          ),
          .reg_ack                 (wbd_uart_ack_i          ),

       // Pad interface
          .scl_pad_i               (i2cm_clk_i              ),
          .scl_pad_o               (i2cm_clk_o              ),
          .scl_pad_oen_o           (i2cm_clk_oen            ),

          .sda_pad_i               (i2cm_data_i             ),
          .sda_pad_o               (i2cm_data_o             ),
          .sda_padoen_o            (i2cm_data_oen           ),
     
          .i2cm_intr_o             (i2cm_intr_o             ),

          .uart_rxd                (uart_rxd                ),
          .uart_txd                (uart_txd                ),

          .usb_in_dp               (usb_dp_i                ),
          .usb_in_dn               (usb_dn_i                ),

          .usb_out_dp              (usb_dp_o                ),
          .usb_out_dn              (usb_dn_o                ),
          .usb_out_tx_oen          (usb_oen                 ),
       
          .usb_intr_o              (usb_intr_o              ),

      // SPIM Master
          .sspim_sck               (sspim_sck               ), 
          .sspim_so                (sspim_so                ),  
          .sspim_si                (sspim_si                ),  
          .sspim_ssn               (sspim_ssn               )  

     );

pinmux_top u_pinmux(
`ifdef USE_POWER_PINS
          .vccd1                   (vccd1                   ),// User area 1 1.8V supply
          .vssd1                   (vssd1                   ),// User area 1 digital ground
`endif
        //clk skew adjust
          .cfg_cska_pinmux         (cfg_wcska_pinmux_rp      ),
          .wbd_clk_int             (wbd_clk_pinmux_rp       ),
          .wbd_clk_pinmux          (wbd_clk_pinmux_skew     ),

        // System Signals
        // Inputs
          .mclk                    (wbd_clk_pinmux_skew     ),
          .e_reset_n               (e_reset_n_rp            ),
          .p_reset_n               (p_reset_n_rp            ),
          .s_reset_n               (wbd_int_rst_n           ),

          .cfg_strap_pad_ctrl      (cfg_strap_pad_ctrl_rp   ),
          .system_strap            (system_strap_rp         ),
          .strap_sticky            (strap_sticky            ),
	      .strap_uartm             (strap_uartm             ),

          .user_clock1             (wb_clk_i                ),
          .user_clock2             (user_clock2             ),
          .int_pll_clock           (int_pll_clock           ),
          .xtal_clk                (xtal_clk                ),
          .cpu_clk                 (cpu_clk_rp_pinmux       ),


          .rtc_clk                 (rtc_clk                 ),
          .usb_clk                 (usb_clk                 ),
	// Reset Control
          .cpu_core_rst_n          (cpu_core_rst_n          ),
          .cpu_intf_rst_n          (cpu_intf_rst_n          ),
          .qspim_rst_n             (qspim_rst_n             ),
          .sspim_rst_n             (sspim_rst_n             ),
          .uart_rst_n              (uart_rst_n              ),
          .i2cm_rst_n              (i2c_rst_n               ),
          .usb_rst_n               (usb_rst_n               ),

	      .cfg_riscv_ctrl          (cfg_riscv_ctrl          ),

        // Reg Bus Interface Signal
          .reg_cs                  (wbd_glbl_stb_o          ),
          .reg_wr                  (wbd_glbl_we_o           ),
          .reg_addr                (wbd_glbl_adr_o          ),
          .reg_wdata               (wbd_glbl_dat_o          ),
          .reg_be                  (wbd_glbl_sel_o          ),

       // Outputs
          .reg_rdata               (wbd_glbl_dat_i          ),
          .reg_ack                 (wbd_glbl_ack_i          ),


       // Risc configuration
          .irq_lines               (irq_lines               ),
          .soft_irq                (soft_irq                ),
          .user_irq                (user_irq                ),
          .usb_intr                (usb_intr_o              ),
          .i2cm_intr               (i2cm_intr_o             ),

       // Digital IO
          .digital_io_out          (io_out                  ),
          .digital_io_oen          (io_oeb                  ),
          .digital_io_in           (io_in                   ),

       // SFLASH I/F
          .sflash_sck              (sflash_sck              ),
          .sflash_ss               (spi_csn                 ),
          .sflash_oen              (sflash_oen              ),
          .sflash_do               (sflash_do               ),
          .sflash_di               (sflash_di               ),


       // USB I/F
          .usb_dp_o                (usb_dp_o                ),
          .usb_dn_o                (usb_dn_o                ),
          .usb_oen                 (usb_oen                 ),
          .usb_dp_i                (usb_dp_i                ),
          .usb_dn_i                (usb_dn_i                ),

       // UART I/F
          .uart_txd                (uart_txd                ),
          .uart_rxd                (uart_rxd                ),

       // I2CM I/F
          .i2cm_clk_o              (i2cm_clk_o              ),
          .i2cm_clk_i              (i2cm_clk_i              ),
          .i2cm_clk_oen            (i2cm_clk_oen            ),
          .i2cm_data_oen           (i2cm_data_oen           ),
          .i2cm_data_o             (i2cm_data_o             ),
          .i2cm_data_i             (i2cm_data_i             ),

       // SPI MASTER
          .spim_sck                (sspim_sck               ),
          .spim_ssn                (sspim_ssn               ),
          .spim_miso               (sspim_so                ),
          .spim_mosi               (sspim_si                ),
       
       // SPI SLAVE
          .spis_sck                (sspis_sck               ),
          .spis_ssn                (sspis_ssn               ),
          .spis_miso               (sspis_so                ),
          .spis_mosi               (sspis_si                ),

      // UART MASTER I/F
          .uartm_rxd               (uartm_rxd               ),
          .uartm_txd               (uartm_txd               ),


	  .pulse1m_mclk            (pulse1m_mclk            ),

	  .pinmux_debug            (pinmux_debug            ),


       .cfg_pll_enb            (cfg_pll_enb             ), 
       .cfg_pll_fed_div        (cfg_pll_fed_div         ), 
       .cfg_dco_mode           (cfg_dco_mode            ), 
       .cfg_dc_trim            (cfg_dc_trim             ),
       .pll_ref_clk            (pll_ref_clk             ),

       .cfg_dac0_mux_sel       (cfg_dac0_mux_sel        ),
       .cfg_dac1_mux_sel       (cfg_dac1_mux_sel        ),
       .cfg_dac2_mux_sel       (cfg_dac2_mux_sel        ),
       .cfg_dac3_mux_sel       (cfg_dac3_mux_sel        )

   ); 


dac_top  u_4x8bit_dac(
`ifdef USE_POWER_PINS
    .vccd1                 (vdda1                  ),
    .vssd1                 (vssa1                  ),
`endif
    .Vref (analog_io[23]),
    .DIn0 (cfg_dac0_mux_sel),
    .DIn1 (cfg_dac1_mux_sel),
    .DIn2 (cfg_dac2_mux_sel),
    .DIn3 (cfg_dac3_mux_sel),
    .Vout0(analog_io[15]   ),
    .Vout1(analog_io[16]   ),
    .Vout2(analog_io[17]   ),
    .Vout3(analog_io[18]   )
   );


endmodule : user_project_wrapper