| //////////////////////////////////////////////////////////////////////////// |
| // SPDX-FileCopyrightText: 2021 , Dinesh Annayya |
| // |
| // Licensed under the Apache License, Version 2.0 (the "License"); |
| // you may not use this file except in compliance with the License. |
| // You may obtain a copy of the License at |
| // |
| // http://www.apache.org/licenses/LICENSE-2.0 |
| // |
| // Unless required by applicable law or agreed to in writing, software |
| // distributed under the License is distributed on an "AS IS" BASIS, |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| // See the License for the specific language governing permissions and |
| // limitations under the License. |
| // SPDX-License-Identifier: Apache-2.0 |
| // SPDX-FileContributor: Modified by Dinesh Annayya <dinesha@opencores.org> |
| ////////////////////////////////////////////////////////////////////// |
| //// //// |
| //// Standalone User validation Test bench //// |
| //// //// |
| //// This file is part of the riscdunio cores project //// |
| //// https://github.com/dineshannayya/riscdunio.git //// |
| //// //// |
| //// Description //// |
| //// This is a standalone test bench to validate the //// |
| //// Digital core. //// |
| //// This test bench to valid Arduino example: //// |
| //// //// |
| //// //// |
| //// To Do: //// |
| //// nothing //// |
| //// //// |
| //// Author(s): //// |
| //// - Dinesh Annayya, dinesh.annayya@gmail.com //// |
| //// //// |
| //// Revision : //// |
| //// 0.1 - 29th July 2022, Dinesh A //// |
| //// //// |
| ////////////////////////////////////////////////////////////////////// |
| //// //// |
| //// Copyright (C) 2000 Authors and OPENCORES.ORG //// |
| //// //// |
| //// This source file may be used and distributed without //// |
| //// restriction provided that this copyright statement is not //// |
| //// removed from the file and that any derivative work contains //// |
| //// the original copyright notice and the associated disclaimer. //// |
| //// //// |
| //// This source file is free software; you can redistribute it //// |
| //// and/or modify it under the terms of the GNU Lesser General //// |
| //// Public License as published by the Free Software Foundation; //// |
| //// either version 2.1 of the License, or (at your option) any //// |
| //// later version. //// |
| //// //// |
| //// This source is distributed in the hope that it will be //// |
| //// useful, but WITHOUT ANY WARRANTY; without even the implied //// |
| //// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR //// |
| //// PURPOSE. See the GNU Lesser General Public License for more //// |
| //// details. //// |
| //// //// |
| //// You should have received a copy of the GNU Lesser General //// |
| //// Public License along with this source; if not, download it //// |
| //// from http://www.opencores.org/lgpl.shtml //// |
| //// //// |
| ////////////////////////////////////////////////////////////////////// |
| |
| `default_nettype wire |
| |
| `timescale 1 ns / 1 ns |
| |
| `include "sram_macros/sky130_sram_2kbyte_1rw1r_32x512_8.v" |
| `include "is62wvs1288.v" |
| `include "user_params.svh" |
| `include "uart_agent.v" |
| |
| `define TB_HEX "arduino_hello_world.hex" |
| `define TB_TOP arduino_hello_world_tb |
| module `TB_TOP; |
| parameter real CLK1_PERIOD = 20; // 50Mhz |
| parameter real CLK2_PERIOD = 2.5; |
| parameter real IPLL_PERIOD = 5.008; |
| parameter real XTAL_PERIOD = 6; |
| |
| `include "user_tasks.sv" |
| |
| //---------------------------------- |
| // Uart Configuration |
| // --------------------------------- |
| reg [1:0] uart_data_bit ; |
| reg uart_stop_bits ; // 0: 1 stop bit; 1: 2 stop bit; |
| reg uart_stick_parity ; // 1: force even parity |
| reg uart_parity_en ; // parity enable |
| reg uart_even_odd_parity ; // 0: odd parity; 1: even parity |
| |
| reg [7:0] uart_data ; |
| reg [15:0] uart_divisor ; // divided by n * 16 |
| reg [15:0] uart_timeout ;// wait time limit |
| |
| reg [15:0] uart_rx_nu ; |
| reg [15:0] uart_tx_nu ; |
| reg [7:0] uart_write_data [0:39]; |
| reg uart_fifo_enable ; // fifo mode disable |
| reg flag ; |
| |
| |
| integer i,j; |
| |
| |
| |
| |
| initial begin |
| flag = 0; |
| end |
| |
| `ifdef WFDUMP |
| initial begin |
| $dumpfile("simx.vcd"); |
| $dumpvars(3, `TB_TOP); |
| //$dumpvars(0, `TB_TOP.u_top.u_riscv_top.i_core_top_0); |
| //$dumpvars(0, `TB_TOP.u_top.u_riscv_top.u_connect); |
| //$dumpvars(0, `TB_TOP.u_top.u_riscv_top.u_intf); |
| $dumpvars(0, `TB_TOP.u_top.u_uart_i2c_usb_spi.u_uart0_core); |
| end |
| `endif |
| |
| initial begin |
| uart_data_bit = 2'b11; |
| uart_stop_bits = 0; // 0: 1 stop bit; 1: 2 stop bit; |
| uart_stick_parity = 0; // 1: force even parity |
| uart_parity_en = 0; // parity enable |
| uart_even_odd_parity = 1; // 0: odd parity; 1: even parity |
| tb_set_uart_baud(50000000,230400,uart_divisor);// 50Mhz Ref clock, Baud Rate: 230400 |
| uart_timeout = 500;// wait time limit |
| uart_fifo_enable = 0; // fifo mode disable |
| |
| $value$plusargs("risc_core_id=%d", d_risc_id); |
| |
| #200; // Wait for reset removal |
| repeat (10) @(posedge clock); |
| $display("Monitor: Standalone User Risc Boot Test Started"); |
| |
| init(); |
| wait_riscv_boot(); |
| // Remove Wb Reset |
| //wb_user_core_write(`ADDR_SPACE_WBHOST+`WBHOST_GLBL_CFG,'h1); |
| |
| repeat (2) @(posedge clock); |
| #1; |
| // Remove all the reset |
| if(d_risc_id == 0) begin |
| $display("STATUS: Working with Risc core 0"); |
| //wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h11F); |
| end else if(d_risc_id == 1) begin |
| $display("STATUS: Working with Risc core 1"); |
| wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h21F); |
| end else if(d_risc_id == 2) begin |
| $display("STATUS: Working with Risc core 2"); |
| wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h41F); |
| end else if(d_risc_id == 3) begin |
| $display("STATUS: Working with Risc core 3"); |
| wb_user_core_write(`ADDR_SPACE_GLBL+`GLBL_CFG_CFG0,'h81F); |
| end |
| |
| |
| tb_uart.uart_init; |
| tb_uart.control_setup (uart_data_bit, uart_stop_bits, uart_parity_en, uart_even_odd_parity, |
| uart_stick_parity, uart_timeout, uart_divisor); |
| |
| repeat (8000) @(posedge clock); // wait for Processor Get Ready |
| flag = 1; |
| |
| |
| uart_write_data[0] = "H"; |
| uart_write_data[1] = "e"; |
| uart_write_data[2] = "l"; |
| uart_write_data[3] = "l"; |
| uart_write_data[4] = "o"; |
| uart_write_data[5] = " "; |
| uart_write_data[6] = "W"; |
| uart_write_data[7] = "o"; |
| uart_write_data[8] = "r"; |
| uart_write_data[9] = "l"; |
| uart_write_data[10] = "d"; |
| uart_write_data[11] = "!"; |
| |
| |
| fork |
| begin |
| for (j=0; j<12; j=j+1) |
| begin |
| tb_uart.read_char_chk(uart_write_data[j]); |
| end |
| end |
| join |
| |
| #100 |
| tb_uart.report_status(uart_rx_nu, uart_tx_nu); |
| |
| test_fail = 0; |
| |
| // Check |
| // if all the 12 byte received |
| // if no error |
| if(uart_rx_nu != 12) test_fail = 1; |
| if(tb_uart.err_cnt != 0) test_fail = 1; |
| |
| |
| $display("###################################################"); |
| if(test_fail == 0) begin |
| `ifdef GL |
| $display("Monitor: %m (GL) Passed"); |
| `else |
| $display("Monitor: %m (RTL) Passed"); |
| `endif |
| end else begin |
| `ifdef GL |
| $display("Monitor: %m (GL) Failed"); |
| `else |
| $display("Monitor: %m (RTL) Failed"); |
| `endif |
| end |
| $display("###################################################"); |
| $finish; |
| end |
| |
| // SSPI Slave I/F |
| assign io_in[5] = 1'b1; // RESET |
| assign io_in[21] = 1'b0; // CLOCK |
| |
| `ifndef GL // Drive Power for Hold Fix Buf |
| // All standard cell need power hook-up for functionality work |
| initial begin |
| |
| end |
| `endif |
| |
| //------------------------------------------------------ |
| // Integrate the Serial flash with qurd support to |
| // user core using the gpio pads |
| // ---------------------------------------------------- |
| |
| wire flash_clk = (io_oeb[28] == 1'b0) ? io_out[28]: 1'b0; |
| wire flash_csb = (io_oeb[29] == 1'b0) ? io_out[29]: 1'b0; |
| // Creating Pad Delay |
| wire #1 io_oeb_33 = io_oeb[33]; |
| wire #1 io_oeb_34 = io_oeb[34]; |
| wire #1 io_oeb_35 = io_oeb[35]; |
| wire #1 io_oeb_36 = io_oeb[36]; |
| tri #1 flash_io0 = (io_oeb_33== 1'b0) ? io_out[33] : 1'bz; |
| tri #1 flash_io1 = (io_oeb_34== 1'b0) ? io_out[34] : 1'bz; |
| tri #1 flash_io2 = (io_oeb_35== 1'b0) ? io_out[35] : 1'bz; |
| tri #1 flash_io3 = (io_oeb_36== 1'b0) ? io_out[36] : 1'bz; |
| |
| assign io_in[33] = (io_oeb[33] == 1'b1) ? flash_io0: 1'b0; |
| assign io_in[34] = (io_oeb[34] == 1'b1) ? flash_io1: 1'b0; |
| assign io_in[35] = (io_oeb[35] == 1'b1) ? flash_io2: 1'b0; |
| assign io_in[36] = (io_oeb[36] == 1'b1) ? flash_io3: 1'b0; |
| |
| // Quard flash |
| s25fl256s #(.mem_file_name(`TB_HEX), |
| .otp_file_name("none"), |
| .TimingModel("S25FL512SAGMFI010_F_30pF")) |
| u_spi_flash_256mb ( |
| // Data Inputs/Outputs |
| .SI (flash_io0), |
| .SO (flash_io1), |
| // Controls |
| .SCK (flash_clk), |
| .CSNeg (flash_csb), |
| .WPNeg (flash_io2), |
| .HOLDNeg (flash_io3), |
| .RSTNeg (!wb_rst_i) |
| |
| ); |
| |
| wire spiram_csb = (io_oeb[31] == 1'b0) ? io_out[31] : 1'b0; |
| |
| is62wvs1288 #(.mem_file_name("none")) |
| u_sram ( |
| // Data Inputs/Outputs |
| .io0 (flash_io0), |
| .io1 (flash_io1), |
| // Controls |
| .clk (flash_clk), |
| .csb (spiram_csb), |
| .io2 (flash_io2), |
| .io3 (flash_io3) |
| ); |
| |
| //--------------------------- |
| // UART Agent integration |
| // -------------------------- |
| wire uart_txd,uart_rxd; |
| |
| assign uart_txd = (io_oeb[7] == 1'b0) ? io_out[7] : 1'b0; |
| assign io_in[6] = (io_oeb[6] == 1'b1) ? uart_rxd : 1'b0 ; |
| |
| uart_agent tb_uart( |
| .mclk (clock ), |
| .txd (uart_rxd ), |
| .rxd (uart_txd ) |
| ); |
| |
| |
| endmodule |
| `include "s25fl256s.sv" |
| `default_nettype wire |
