blob: 0b3f35f160a82449149a29756b86535f6ddb99ff [file] [log] [blame]
# SPDX-FileCopyrightText: 2021 , Dinesh Annayya
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
# SPDX-License-Identifier: Apache-2.0
# SPDX-FileContributor: Modified by Dinesh Annayya <dinesha@opencores.org>
# Global
# ------
set script_dir [file dirname [file normalize [info script]]]
# Name
set ::env(DESIGN_NAME) peri_top
set ::env(DESIGN_IS_CORE) "0"
set ::env(FP_PDN_CORE_RING) "0"
# Timing configuration
set ::env(CLOCK_PERIOD) "10"
set ::env(CLOCK_PORT) "mclk rtc_clk"
set ::env(SYNTH_MAX_FANOUT) 4
set ::env(SYNTH_BUFFERING) {0}
## CTS BUFFER
set ::env(CTS_CLK_BUFFER_LIST) "sky130_fd_sc_hd__clkbuf_4 sky130_fd_sc_hd__clkbuf_8"
set ::env(CTS_SINK_CLUSTERING_SIZE) "16"
set ::env(CLOCK_BUFFER_FANOUT) "8"
# Sources
# -------
# Local sources + no2usb sources
set ::env(VERILOG_FILES) "\
$::env(DESIGN_DIR)/../../verilog/rtl/lib/clk_skew_adjust.gv \
$::env(DESIGN_DIR)/../../verilog/rtl/rtc/verilog/rtl/core/rtc_top.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/rtc/verilog/rtl/core/rtc_core.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/rtc/verilog/rtl/core/rtc_reg.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/peripheral/src/peri_top.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/dig2ana/src/dig2ana_reg.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/lib/ctech_cells.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/lib/reset_sync.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/lib/async_reg_bus.sv \
$::env(DESIGN_DIR)/../../verilog/rtl/lib/registers.v \
"
set ::env(VERILOG_INCLUDE_DIRS) [glob $::env(DESIGN_DIR)/../../verilog/rtl/ ]
set ::env(SYNTH_DEFINES) [list SYNTHESIS ]
set ::env(SYNTH_READ_BLACKBOX_LIB) 1
set ::env(SDC_FILE) $::env(DESIGN_DIR)/base.sdc
set ::env(BASE_SDC_FILE) $::env(DESIGN_DIR)/base.sdc
set ::env(LEC_ENABLE) 0
set ::env(VDD_PIN) [list {vccd1}]
set ::env(GND_PIN) [list {vssd1}]
# Floorplanning
# -------------
set ::env(FP_PIN_ORDER_CFG) $::env(DESIGN_DIR)/pin_order.cfg
set ::env(FP_SIZING) absolute
set ::env(DIE_AREA) "0 0 400 200"
# If you're going to use multiple power domains, then keep this disabled.
set ::env(RUN_CVC) 0
#set ::env(PDN_CFG) $script_dir/pdn.tcl
set ::env(PL_TIME_DRIVEN) 1
set ::env(PL_TARGET_DENSITY) "0.35"
set ::env(CELL_PAD) "8"
#set ::env(GRT_ADJUSTMENT) {0.2}
######################################################################################
# Metal-2/3 Signal are Routed near to block boundary is creating DRC violation at Top-level
# during pad connectivity
#set ::env(GRT_OBS) " \
# met2 0 2 500 3, \
# met2 0 747 500 748, \
# met3 2 0 3 750, \
# met3 497 0 498 750"
# helps in anteena fix
set ::env(USE_ARC_ANTENNA_CHECK) "1"
set ::env(FP_IO_VEXTEND) 4
set ::env(FP_IO_HEXTEND) 4
set ::env(FP_PDN_VPITCH) 100
set ::env(FP_PDN_HPITCH) 100
set ::env(FP_PDN_VWIDTH) 6.2
set ::env(FP_PDN_HWIDTH) 6.2
#set ::env(GLB_RT_MAXLAYER) 5
set ::env(RT_MAX_LAYER) {met4}
#Lef
set ::env(MAGIC_GENERATE_LEF) {1}
set ::env(MAGIC_WRITE_FULL_LEF) {0}
set ::env(DIODE_INSERTION_STRATEGY) 4
#LVS Issue - DEF Base looks to having issue
set ::env(MAGIC_EXT_USE_GDS) {1}
set ::env(GLB_RESIZER_MAX_SLEW_MARGIN) {1.5}
set ::env(PL_RESIZER_MAX_SLEW_MARGIN) {1.5}
set ::env(GLB_RESIZER_MAX_CAP_MARGIN) {0.25}
set ::env(PL_RESIZER_MAX_CAP_MARGIN) {0.25}
set ::env(GLB_RESIZER_MAX_WIRE_LENGTH) {500}
set ::env(PL_RESIZER_MAX_WIRE_LENGTH) {500}
set ::env(QUIT_ON_TIMING_VIOLATIONS) "0"
set ::env(QUIT_ON_MAGIC_DRC) "1"
set ::env(QUIT_ON_LVS_ERROR) "1"
set ::env(QUIT_ON_SLEW_VIOLATIONS) "0"