// OpenRAM SRAM model
// Words: 256
// Word size: 32
// Write size: 8

module sky130_sram_1kbyte_1rw1r_32x256_8(
  `ifdef USE_POWER_PINS
      vccd1,
      vssd1,
  `endif
  // Port 0: RW
      clk0,csb0,web0,wmask0,addr0,din0,dout0,
  // Port 1: R
      clk1,csb1,addr1,dout1
    );
  
    parameter NUM_WMASKS = 4 ;
    parameter DATA_WIDTH = 32 ;
    parameter ADDR_WIDTH = 8 ;
    parameter RAM_DEPTH = 1 << ADDR_WIDTH;
    // FIXME: This delay is arbitrary.
    parameter DELAY = 3 ;
    parameter VERBOSE = 1 ; //Set to 0 to only display warnings
    parameter T_HOLD = 1 ; //Delay to hold dout value after posedge. Value is arbitrary
  
  `ifdef USE_POWER_PINS
      inout vccd1;
      inout vssd1;
  `endif
    input  clk0; // clock
    input   csb0; // active low chip select
    input  web0; // active low write control
    input [NUM_WMASKS-1:0]   wmask0; // write mask
    input [ADDR_WIDTH-1:0]  addr0;
    input [DATA_WIDTH-1:0]  din0;
    output [DATA_WIDTH-1:0] dout0;
    input  clk1; // clock
    input   csb1; // active low chip select
    input [ADDR_WIDTH-1:0]  addr1;
    output [DATA_WIDTH-1:0] dout1;
  
    reg  csb0_reg;
    reg  web0_reg;
    reg [NUM_WMASKS-1:0]   wmask0_reg;
    reg [ADDR_WIDTH-1:0]  addr0_reg;
    reg [DATA_WIDTH-1:0]  din0_reg;
    reg [DATA_WIDTH-1:0]  dout0;
  
    // All inputs are registers
    always @(posedge clk0)
    begin
      csb0_reg = csb0;
      web0_reg = web0;
      wmask0_reg = wmask0;
      addr0_reg = addr0;
      din0_reg = din0;
      if ( !csb0_reg && web0_reg && VERBOSE ) 
        $display($time," Reading %m addr0=%b dout0=%b",addr0_reg,mem[addr0_reg]);
      if ( !csb0_reg && !web0_reg && VERBOSE )
        $display($time," Writing %m addr0=%b din0=%b wmask0=%b",addr0_reg,din0_reg,wmask0_reg);
    end
  
    reg  csb1_reg;
    reg [ADDR_WIDTH-1:0]  addr1_reg;
    reg [DATA_WIDTH-1:0]  dout1;
  
    // All inputs are registers
    always @(posedge clk1)
    begin
      csb1_reg = csb1;
      addr1_reg = addr1;
      if (!csb0 && !web0 && !csb1 && (addr0 == addr1))
           $display($time," WARNING: Writing and reading addr0=%b and addr1=%b simultaneously!",addr0,addr1);
      // if ( !csb1_reg && VERBOSE ) 
        // $display($time," Reading %m addr1=%b dout1=%b",addr1_reg,mem[addr1_reg]);s
    end
  
  reg [DATA_WIDTH-1:0]    mem [0:RAM_DEPTH-1];
  
    // Memory Write Block Port 0
    // Write Operation : When web0 = 0, csb0 = 0
    always @ (negedge clk0)
    begin : MEM_WRITE0
      if ( !csb0_reg && !web0_reg ) begin
          if (wmask0_reg[0])
                  mem[addr0_reg][7:0] = din0_reg[7:0];
          if (wmask0_reg[1])
                  mem[addr0_reg][15:8] = din0_reg[15:8];
          if (wmask0_reg[2])
                  mem[addr0_reg][23:16] = din0_reg[23:16];
          if (wmask0_reg[3])
                  mem[addr0_reg][31:24] = din0_reg[31:24];
      end
    end
  
    // Memory Read Block Port 0
    // Read Operation : When web0 = 1, csb0 = 0
    always @ (negedge clk0)
    begin : MEM_READ0
      if (!csb0_reg && web0_reg)
         dout0 <=  mem[addr0_reg];
    end
  
    // Memory Read Block Port 1
    // Read Operation : When web1 = 1, csb1 = 0
    always @ (negedge clk1)
    begin : MEM_READ1
      if (!csb1_reg)
         dout1 <=  mem[addr1_reg];
    end
  
  endmodule