// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none

`timescale 1 ns / 1 ps

module peripheralsGPIO_tb;
	reg clock;
	reg RSTB;
	reg CSB;
	reg power1, power2;
	reg power3, power4;

	wire gpio;
	wire [37:0] mprj_io;

	reg[1:0] inputTestData;
	wire succesOutput = mprj_io[12];
	wire nextTestOutput = mprj_io[13];
	wire[3:0] outputTestData = mprj_io[17:14];

	// Need to add pullup to io3 otherwise GL simulation wont work
	pullup(mprj_io[3]);
	assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz;
	
	assign mprj_io[20:19] = inputTestData;
	assign mprj_io[7] = 1'b1;

	// Need to add pulls (can be up or down) to all unsed io so that input data is known
	assign mprj_io[2:0] = 3'b0;
	assign mprj_io[6:4] = 3'b0;
	assign mprj_io[11:8] = 4'b0;
	assign mprj_io[18] = 1'b0;
	assign mprj_io[37:21] = 17'b0;

	// External clock is used by default.  Make this artificially fast for the
	// simulation.  Normally this would be a slow clock and the digital PLL
	// would be the fast clock.
	always #12.5 clock <= (clock === 1'b0);

	initial begin
		clock = 0;
		inputTestData = 4'b0;
	end

	// Generate input signal
	initial begin
		// Test input from first gpio bank
		@(posedge nextTestOutput);

		// Test input from second gpio bank
		@(posedge nextTestOutput);
		inputTestData = 2'b10;
		
		@(posedge nextTestOutput);
		inputTestData = 2'b01;
		
		@(posedge nextTestOutput);
		inputTestData = 2'b11;

		@(posedge nextTestOutput);
		inputTestData = 2'b00;
	end

	initial begin
		$dumpfile("peripheralsGPIO.vcd");

`ifdef SIM
		$dumpvars(0, peripheralsGPIO_tb);
`else
		$dumpvars(1, peripheralsGPIO_tb);
		$dumpvars(2, peripheralsGPIO_tb.uut.mprj);
`endif

		// Repeat cycles of 1000 clock edges as needed to complete testbench
		repeat (400) begin
			repeat (1000) @(posedge clock);
			//$display("+1000 cycles");
		end
		$display("%c[1;35m",27);
		`ifdef GL
			$display ("Monitor: Timeout, Peripherals GPIO Test (GL) Failed");
		`else
			$display ("Monitor: Timeout, Peripherals GPIO Test (RTL) Failed");
		`endif
		$display("%c[0m",27);
		$finish;
	end

	initial begin
	    // Observe Output pins
		wait(outputTestData == 4'b0000);
		wait(outputTestData == 4'b0001);
		wait(outputTestData == 4'b0011);
		wait(outputTestData == 4'b0111);
		wait(outputTestData == 4'b1111);
		wait(outputTestData == 4'b0000);
		wait(outputTestData == 4'b1111);
		wait(outputTestData == 4'b1110);
		wait(outputTestData == 4'b1100);
		wait(outputTestData == 4'b1000);
		wait(outputTestData == 4'b0000);

		// Wait for tests
		@(posedge nextTestOutput);
		@(posedge nextTestOutput);
		@(posedge nextTestOutput);
		@(posedge nextTestOutput);
		@(posedge nextTestOutput);

		// Wait for management core to output a output test result
		@(posedge nextTestOutput);
		
		if (succesOutput) begin
			$display("%c[1;92m",27);
			`ifdef GL
				$display("Monitor: Peripherals GPIO Test (GL) Passed");
			`else
				$display("Monitor: Peripherals GPIO Test (RTL) Passed");
			`endif
			$display("%c[0m",27);
		end else begin
			$display("%c[1;31m",27);
			`ifdef GL
				$display ("Monitor: Peripherals GPIO Test (GL) Failed");
			`else
				$display ("Monitor: Peripherals GPIO Test (RTL) Failed");
			`endif
			$display("%c[0m",27);
		end
	    $finish;
	end

	initial begin
		RSTB <= 1'b0;
		CSB  <= 1'b1;		// Force CSB high
		#2000;
		RSTB <= 1'b1;	    	// Release reset
		#300000;
		CSB = 1'b0;		// CSB can be released
	end

	initial begin		// Power-up sequence
		power1 <= 1'b0;
		power2 <= 1'b0;
		power3 <= 1'b0;
		power4 <= 1'b0;
		#100;
		power1 <= 1'b1;
		#100;
		power2 <= 1'b1;
		#100;
		power3 <= 1'b1;
		#100;
		power4 <= 1'b1;
	end

	always @(succesOutput, nextTestOutput, outputTestData, inputTestData) begin
		#1 $display("Success:0b%b Next test:0b%b Output:0b%b Input:0b%b", succesOutput, nextTestOutput, outputTestData, inputTestData);
	end

	wire flash_csb;
	wire flash_clk;
	wire flash_io0;
	wire flash_io1;

	wire VDD3V3;
	wire VDD1V8;
	wire VSS;
	
	assign VDD3V3 = power1;
	assign VDD1V8 = power2;
	assign VSS = 1'b0;

	caravel uut (
		.vddio	  (VDD3V3),
		.vddio_2  (VDD3V3),
		.vssio	  (VSS),
		.vssio_2  (VSS),
		.vdda	  (VDD3V3),
		.vssa	  (VSS),
		.vccd	  (VDD1V8),
		.vssd	  (VSS),
		.vdda1    (VDD3V3),
		.vdda1_2  (VDD3V3),
		.vdda2    (VDD3V3),
		.vssa1	  (VSS),
		.vssa1_2  (VSS),
		.vssa2	  (VSS),
		.vccd1	  (VDD1V8),
		.vccd2	  (VDD1V8),
		.vssd1	  (VSS),
		.vssd2	  (VSS),
		.clock    (clock),
		.gpio     (gpio),
		.mprj_io  (mprj_io),
		.flash_csb(flash_csb),
		.flash_clk(flash_clk),
		.flash_io0(flash_io0),
		.flash_io1(flash_io1),
		.resetb	  (RSTB)
	);

	spiflash #(
		.FILENAME("peripheralsGPIO.hex")
	) spiflash (
		.csb(flash_csb),
		.clk(flash_clk),
		.io0(flash_io0),
		.io1(flash_io1),
		.io2(),			// not used
		.io3()			// not used
	);

endmodule
`default_nettype wire