////////////////////////////////////////////////////////////////////////////
// SPDX-FileCopyrightText: 2022 , Julien OURY                       
// 
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
// SPDX-FileContributor: Created by Julien OURY <julien.oury@outlook.fr>
//
////////////////////////////////////////////////////////////////////////////

`default_nettype none

`timescale 1 ns / 1 ps

module nec_ir_receiver_tb;
  reg clock;
  reg RSTB;
  reg CSB;
  reg power1, power2;
  reg power3, power4;

  wire gpio;
  wire [37:0] mprj_io;
  wire [15:0] checkbits;
  wire [7:0] addrbits;
  wire [7:0] databits;
  
  reg [7:0]  cmd_addr;
  reg [7:0]  cmd_data;

  assign checkbits = mprj_io[31:16];
  assign addrbits  = mprj_io[15:8];
  assign databits  = mprj_io[7:0];
  
  assign (pull1,pull0)  mprj_io[37:0] = 38'b11111111111111111111111111111111111111;

  // External clock is used by default.  Make this artificially fast for the
  // simulation.  Normally this would be a slow clock and the digital PLL
  // would be the fast clock.

  always #12.5 clock <= (clock === 1'b0);

  initial begin
    clock = 0;
  end

  initial begin
    $dumpfile("nec_ir_receiver.vcd");
    $dumpvars(0, nec_ir_receiver_tb);

    // Repeat cycles of 1000 clock edges as needed to complete testbench
    repeat (7000) begin
      repeat (1000) @(posedge clock);
      // $display("+1000 cycles");
    end
    $display("%c[1;31m",27);
    `ifdef GL
      $display ("Monitor: Timeout, Test Mega-Project WB Port (GL) Failed");
    `else
      $display ("Monitor: Timeout, Test Mega-Project WB Port (RTL) Failed");
    `endif
    $display("%c[0m",27);
    $finish;
  end
  
  initial begin
    ir_drv.init(0, 56250); //Protocol tick period divided by 10 for simulation speed-up
    cmd_addr = $random%256;
    cmd_data = $random%256;
	wait(checkbits == 16'hAB60);
	ir_drv.send_nec(cmd_addr, cmd_data);
  end

  initial begin
    
    wait(checkbits == 16'hAB60);

    $display("Monitor: MPRJ-Logic WB Started");
    
    wait (checkbits == 16'hAB61);
    if ((addrbits == cmd_addr) && (databits == cmd_data)) begin
      `ifdef GL
        $display("Monitor: Mega-Project WB (GL) Passed");
      `else
        $display("Monitor: Mega-Project WB (RTL) Passed");
      `endif
    end else begin
      `ifdef GL
        $display("Monitor: Mega-Project WB (GL) Failed [0x%h -> 0x%h]", addrbits, databits);
      `else
        $display("Monitor: Mega-Project WB (RTL) Failed [0x%h -> 0x%h]", addrbits, databits);
      `endif
    end
    $finish;
  end

  initial begin
    RSTB <= 1'b0;
    CSB  <= 1'b1;    // Force CSB high
    #2000;
    RSTB <= 1'b1;        // Release reset
    #100000;
    CSB = 1'b0;    // CSB can be released
  end

  initial begin    // Power-up sequence
    power1 <= 1'b0;
    power2 <= 1'b0;
    #200;
    power1 <= 1'b1;
    #200;
    power2 <= 1'b1;
  end

  wire flash_csb;
  wire flash_clk;
  wire flash_io0;
  wire flash_io1;

  wire VDD3V3 = power1;
  wire VDD1V8 = power2;
  wire VSS = 1'b0;
  
  ir_behavioral_driver ir_drv(
    .ir_signal(mprj_io[37])
  );

  caravel uut (
    .vddio    (VDD3V3),
    .vddio_2  (VDD3V3),
    .vssio    (VSS),
    .vssio_2  (VSS),
    .vdda    (VDD3V3),
    .vssa    (VSS),
    .vccd    (VDD1V8),
    .vssd    (VSS),
    .vdda1    (VDD3V3),
    .vdda1_2  (VDD3V3),
    .vdda2    (VDD3V3),
    .vssa1    (VSS),
    .vssa1_2  (VSS),
    .vssa2    (VSS),
    .vccd1    (VDD1V8),
    .vccd2    (VDD1V8),
    .vssd1    (VSS),
    .vssd2    (VSS),
    .clock    (clock),
    .gpio     (gpio),
    .mprj_io  (mprj_io),
    .flash_csb(flash_csb),
    .flash_clk(flash_clk),
    .flash_io0(flash_io0),
    .flash_io1(flash_io1),
    .resetb    (RSTB)
  );

  spiflash #(
    .FILENAME("nec_ir_receiver.hex")
  ) spiflash (
    .csb(flash_csb),
    .clk(flash_clk),
    .io0(flash_io0),
    .io1(flash_io1),
    .io2(),      // not used
    .io3()      // not used
  );

endmodule
`default_nettype wire