diff --git a/verilog/dv/arduino_arrays/Makefile b/verilog/dv/arduino_arrays/Makefile
new file mode 100644
index 0000000..dad099c
--- /dev/null
+++ b/verilog/dv/arduino_arrays/Makefile
@@ -0,0 +1,140 @@
+# SPDX-FileCopyrightText: 2020 Efabless Corporation
+#
+# Licensed under the Apache License, Version 2.0 (the "License");
+# you may not use this file except in compliance with the License.
+# You may obtain a copy of the License at
+#
+#      http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+#
+# SPDX-License-Identifier: Apache-2.0
+
+
+# ---- Include Partitioned Makefiles ----
+
+CONFIG = caravel_user_project
+ 
+#######################################################################
+## Caravel Verilog for Integration Tests
+#######################################################################
+
+DESIGNS?=../../..
+TOOLS?=/opt/riscv32i/
+
+export USER_PROJECT_VERILOG ?=  $(DESIGNS)/verilog
+export RISCDUINO_BOARD ?=  $(USER_PROJECT_VERILOG)/dv/common/riscduino_board/custom_board/riscduino
+## YIFIVE FIRMWARE
+YIFIVE_FIRMWARE_PATH = $(USER_PROJECT_VERILOG)/dv/firmware
+GCC_PREFIX?=riscv32-unknown-elf
+
+
+## Simulation mode: RTL/GL
+SIM?=RTL
+DUMP?=OFF
+RISC_CORE?=0
+
+### To Enable IVERILOG FST DUMP
+export IVERILOG_DUMPER = fst
+
+
+.SUFFIXES:
+
+PATTERN = arduino_arrays
+
+all:  ${PATTERN:=.vcd}
+
+
+vvp:  ${PATTERN:=.vvp}
+
+%.vvp: %_tb.v
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${PATTERN}.ino.cpp -o ${PATTERN}.ino.cpp.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/Print.cpp -o Print.cpp.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WMath.cpp -o WMath.cpp.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WString.cpp -o WString.cpp.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/WInterrupts.c -o WInterrupts.c.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/drivers/fe300prci/fe300prci_driver.c -o fe300prci_driver.c.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/abi.cpp -o abi.cpp.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/drivers/plic/plic_driver.c -o plic_driver.c.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/UARTClass.cpp -o UARTClass.cpp.o
+	${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/entry.S -o entry.S.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/hooks.c -o hooks.c.o
+	${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/init.S -o init.S.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/itoa.c -o itoa.c.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/main.cpp -o main.cpp.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/malloc.c -o malloc.c.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/new.cpp -o new.cpp.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/sbrk.c -o sbrk.c.o
+	${GCC_PREFIX}-gcc -c -march=rv32imac -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/start.S -o start.S.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring.c -o wiring.c.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_analog.c -o wiring_analog.c.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_digital.c -o wiring_digital.c.o
+	${GCC_PREFIX}-g++ -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -fpermissive -Wall -fno-rtti -fno-exceptions -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_pulse.cpp -o wiring_pulse.cpp.o
+	${GCC_PREFIX}-gcc -c -O2 -march=rv32imac -fpeel-loops -ffreestanding -ffunction-sections -fdata-sections -Wall -I${RISCDUINO_BOARD}/system/include -I${RISCDUINO_BOARD}/sdk/bsp/include -I${RISCDUINO_BOARD}/sdk/bsp/env -I${RISCDUINO_BOARD}/sdk/bsp/drivers -I${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score -include sys/cdefs.h -g -DARDUINO=10607 -DF_CPU=50000000LL -DRISCDUINO_SCORE_DEVKIT -I${RISCDUINO_BOARD}/cores/arduino -I${RISCDUINO_BOARD}/variants/standard ${RISCDUINO_BOARD}/cores/arduino/wiring_shift.c -o wiring_shift.c.o
+	${GCC_PREFIX}-ar rcs core.a Print.cpp.o
+	${GCC_PREFIX}-ar rcs core.a UARTClass.cpp.o
+	${GCC_PREFIX}-ar rcs core.a WInterrupts.c.o
+	${GCC_PREFIX}-ar rcs core.a WMath.cpp.o
+	${GCC_PREFIX}-ar rcs core.a WString.cpp.o
+	${GCC_PREFIX}-ar rcs core.a abi.cpp.o
+	${GCC_PREFIX}-ar rcs core.a fe300prci_driver.c.o
+	${GCC_PREFIX}-ar rcs core.a plic_driver.c.o
+	${GCC_PREFIX}-ar rcs core.a entry.S.o
+	${GCC_PREFIX}-ar rcs core.a hooks.c.o
+	${GCC_PREFIX}-ar rcs core.a init.S.o
+	${GCC_PREFIX}-ar rcs core.a itoa.c.o
+	${GCC_PREFIX}-ar rcs core.a main.cpp.o
+	${GCC_PREFIX}-ar rcs core.a malloc.c.o
+	${GCC_PREFIX}-ar rcs core.a new.cpp.o
+	${GCC_PREFIX}-ar rcs core.a sbrk.c.o
+	${GCC_PREFIX}-ar rcs core.a start.S.o
+	${GCC_PREFIX}-ar rcs core.a wiring.c.o
+	${GCC_PREFIX}-ar rcs core.a wiring_analog.c.o
+	${GCC_PREFIX}-ar rcs core.a wiring_digital.c.o
+	${GCC_PREFIX}-ar rcs core.a wiring_pulse.cpp.o
+	${GCC_PREFIX}-ar rcs core.a wiring_shift.c.o
+	${GCC_PREFIX}-g++ -T ${RISCDUINO_BOARD}/sdk/bsp/env/riscduino_score/link.lds -nostartfiles -Wl,-N -Wl,--gc-sections -Wl,--wrap=malloc -Wl,--wrap=free -Wl,--wrap=sbrk ${PATTERN}.ino.cpp.o -nostdlib -Wl,--start-group core.a -lm -lstdc++ -lc -lgloss -Wl,--end-group -lgcc -o ${PATTERN}.ino.elf
+	${GCC_PREFIX}-objcopy -R .rel.dyn -O binary ${PATTERN}.ino.elf ${PATTERN}.ino.bin
+	${GCC_PREFIX}-objcopy -R .rel.dyn -O verilog ${PATTERN}.ino.elf ${PATTERN}.ino.hex
+	${GCC_PREFIX}-objdump -D  ${PATTERN}.ino.elf >   ${PATTERN}.ino.dump
+	rm *.o *.a
+ifeq ($(SIM),RTL)
+   ifeq ($(DUMP),OFF)
+	iverilog -g2012 -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib  \
+	$< -o $@ 
+    else  
+	iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DSIM -I $(PDK_PATH) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.$(CONFIG) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.rtl.lib  \
+	$< -o $@ 
+   endif
+else  
+   ifeq ($(DUMP),OFF)
+	iverilog -g2012 -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
+	$< -o $@ 
+    else  
+	iverilog -g2012 -DWFDUMP -DFUNCTIONAL -DUSE_POWER_PINS -DGL -I $(PDK_PATH) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.gl.$(CONFIG) \
+	-f$(USER_PROJECT_VERILOG)/includes/includes.gl.lib \
+	$< -o $@ 
+   endif
+endif
+
+%.vcd: %.vvp
+	vvp $< +risc_core_id=$(RISC_CORE)
+
+
+# ---- Clean ----
+
+clean:
+	rm -f *.elf *.hex *.bin *.vvp *.vcd *.log *.dump *.a *.o
+
+.PHONY: clean hex all
diff --git a/verilog/dv/arduino_arrays/arduino_arrays.ino b/verilog/dv/arduino_arrays/arduino_arrays.ino
new file mode 100644
index 0000000..dbbb4b4
--- /dev/null
+++ b/verilog/dv/arduino_arrays/arduino_arrays.ino
@@ -0,0 +1,56 @@
+/*
+  Arrays
+
+  Demonstrates the use of an array to hold pin numbers in order to iterate over
+  the pins in a sequence. Lights multiple LEDs in sequence, then in reverse.
+
+  Unlike the For Loop tutorial, where the pins have to be contiguous, here the
+  pins can be in any random order.
+
+  The circuit:
+  - LEDs from pins 2 through 7 to ground
+
+  created 2006
+  by David A. Mellis
+  modified 30 Aug 2011
+  by Tom Igoe
+
+  This example code is in the public domain.
+
+  https://www.arduino.cc/en/Tutorial/BuiltInExamples/Arrays
+*/
+
+int timer = 100;           // The higher the number, the slower the timing.
+int ledPins[] = {
+  2, 7, 4, 6, 5, 3
+};       // an array of pin numbers to which LEDs are attached
+int pinCount = 6;           // the number of pins (i.e. the length of the array)
+
+void setup() {
+  // the array elements are numbered from 0 to (pinCount - 1).
+  // use a for loop to initialize each pin as an output:
+  for (int thisPin = 0; thisPin < pinCount; thisPin++) {
+    pinMode(ledPins[thisPin], OUTPUT);
+  }
+}
+
+void loop() {
+  // loop from the lowest pin to the highest:
+  for (int thisPin = 0; thisPin < pinCount; thisPin++) {
+    // turn the pin on:
+    digitalWrite(ledPins[thisPin], HIGH);
+    delay(timer);
+    // turn the pin off:
+    digitalWrite(ledPins[thisPin], LOW);
+
+  }
+
+  // loop from the highest pin to the lowest:
+  for (int thisPin = pinCount - 1; thisPin >= 0; thisPin--) {
+    // turn the pin on:
+    digitalWrite(ledPins[thisPin], HIGH);
+    delay(timer);
+    // turn the pin off:
+    digitalWrite(ledPins[thisPin], LOW);
+  }
+}
diff --git a/verilog/dv/arduino_arrays/arduino_arrays.ino.cpp b/verilog/dv/arduino_arrays/arduino_arrays.ino.cpp
new file mode 100644
index 0000000..ebcb90b
--- /dev/null
+++ b/verilog/dv/arduino_arrays/arduino_arrays.ino.cpp
@@ -0,0 +1,63 @@
+#include <Arduino.h>
+/*
+  Arrays
+
+  Demonstrates the use of an array to hold pin numbers in order to iterate over
+  the pins in a sequence. Lights multiple LEDs in sequence, then in reverse.
+
+  Unlike the For Loop tutorial, where the pins have to be contiguous, here the
+  pins can be in any random order.
+
+  The circuit:
+  - LEDs from pins 2 through 7 to ground
+
+  created 2006
+  by David A. Mellis
+  modified 30 Aug 2011
+  by Tom Igoe
+
+  This example code is in the public domain.
+
+  https://www.arduino.cc/en/Tutorial/BuiltInExamples/Arrays
+*/
+
+int timer = 10; // In Milli Second  - The higher the number, the slower the timing.
+int ledPins[] = {
+  2, 7, 4, 6, 5, 3
+};       // an array of pin numbers to which LEDs are attached
+int pinCount = 6;           // the number of pins (i.e. the length of the array)
+
+void setup();
+void loop();
+void setup() {
+  // the array elements are numbered from 0 to (pinCount - 1).
+  // use a for loop to initialize each pin as an output:
+  for (int thisPin = 0; thisPin < pinCount; thisPin++) {
+    pinMode(ledPins[thisPin], OUTPUT);
+  }
+}
+
+void loop() {
+  // loop from the lowest pin to the highest:
+  for (int thisPin = 0; thisPin < pinCount; thisPin++) {
+    // turn the pin on:
+    digitalWrite(ledPins[thisPin], HIGH);
+    //delay(timer);
+    delayMicroseconds(timer);
+    // turn the pin off:
+    digitalWrite(ledPins[thisPin], LOW);
+    delayMicroseconds(timer);
+
+  }
+
+  // loop from the highest pin to the lowest:
+  for (int thisPin = pinCount - 1; thisPin >= 0; thisPin--) {
+    // turn the pin on:
+    digitalWrite(ledPins[thisPin], HIGH);
+    delayMicroseconds(timer);
+    // turn the pin off:
+    digitalWrite(ledPins[thisPin], LOW);
+    delayMicroseconds(timer);
+  }
+}
+
diff --git a/verilog/dv/arduino_arrays/arduino_arrays_tb.v b/verilog/dv/arduino_arrays/arduino_arrays_tb.v
new file mode 100644
index 0000000..b195e2e
--- /dev/null
+++ b/verilog/dv/arduino_arrays/arduino_arrays_tb.v
@@ -0,0 +1,525 @@
+////////////////////////////////////////////////////////////////////////////
+// SPDX-FileCopyrightText:  2021 , Dinesh Annayya
+//
+// Licensed under the Apache License, Version 2.0 (the "License");
+// you may not use this file except in compliance with the License.
+// You may obtain a copy of the License at
+//
+//      http://www.apache.org/licenses/LICENSE-2.0
+//
+// Unless required by applicable law or agreed to in writing, software
+// distributed under the License is distributed on an "AS IS" BASIS,
+// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+// See the License for the specific language governing permissions and
+// limitations under the License.
+// SPDX-License-Identifier: Apache-2.0
+// SPDX-FileContributor: Modified by Dinesh Annayya <dinesha@opencores.org>
+//////////////////////////////////////////////////////////////////////
+////                                                              ////
+////  Standalone User validation Test bench                       ////
+////                                                              ////
+////  This file is part of the YIFive cores project               ////
+////  https://github.com/dineshannayya/yifive_r0.git              ////
+////  http://www.opencores.org/cores/yifive/                      ////
+////                                                              ////
+////  Description                                                 ////
+////   This is a standalone test bench to validate the            ////
+////   Digital core.                                              ////
+////                                                              ////
+////  To Do:                                                      ////
+////    nothing                                                   ////
+////                                                              ////
+////  Author(s):                                                  ////
+////      - Dinesh Annayya, dinesha@opencores.org                 ////
+////                                                              ////
+////  Revision :                                                  ////
+////    0.1 - 16th Feb 2021, Dinesh A                             ////
+////                                                              ////
+//////////////////////////////////////////////////////////////////////
+////                                                              ////
+//// Copyright (C) 2000 Authors and OPENCORES.ORG                 ////
+////                                                              ////
+//// This source file may be used and distributed without         ////
+//// restriction provided that this copyright statement is not    ////
+//// removed from the file and that any derivative work contains  ////
+//// the original copyright notice and the associated disclaimer. ////
+////                                                              ////
+//// This source file is free software; you can redistribute it   ////
+//// and/or modify it under the terms of the GNU Lesser General   ////
+//// Public License as published by the Free Software Foundation; ////
+//// either version 2.1 of the License, or (at your option) any   ////
+//// later version.                                               ////
+////                                                              ////
+//// This source is distributed in the hope that it will be       ////
+//// useful, but WITHOUT ANY WARRANTY; without even the implied   ////
+//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR      ////
+//// PURPOSE.  See the GNU Lesser General Public License for more ////
+//// details.                                                     ////
+////                                                              ////
+//// You should have received a copy of the GNU Lesser General    ////
+//// Public License along with this source; if not, download it   ////
+//// from http://www.opencores.org/lgpl.shtml                     ////
+////                                                              ////
+//////////////////////////////////////////////////////////////////////
+
+`default_nettype wire
+
+`timescale 1 ns / 1 ns
+
+`include "sram_macros/sky130_sram_2kbyte_1rw1r_32x512_8.v"
+`include "is62wvs1288.v"
+
+module arduino_arrays_tb;
+	reg clock;
+	reg wb_rst_i;
+	reg power1, power2;
+	reg power3, power4;
+
+        reg        wbd_ext_cyc_i;  // strobe/request
+        reg        wbd_ext_stb_i;  // strobe/request
+        reg [31:0] wbd_ext_adr_i;  // address
+        reg        wbd_ext_we_i;  // write
+        reg [31:0] wbd_ext_dat_i;  // data output
+        reg [3:0]  wbd_ext_sel_i;  // byte enable
+
+        wire [31:0] wbd_ext_dat_o;  // data input
+        wire        wbd_ext_ack_o;  // acknowlegement
+        wire        wbd_ext_err_o;  // error
+
+	// User I/O
+	wire [37:0] io_oeb;
+	wire [37:0] io_out;
+	wire [37:0] io_in;
+
+	wire gpio;
+	wire [37:0] mprj_io;
+	wire [7:0] mprj_io_0;
+	reg         test_fail;
+	reg [31:0] read_data;
+	reg            flag                 ;
+
+parameter P_FSM_C      = 4'b0000; // Command Phase Only
+parameter P_FSM_CW     = 4'b0001; // Command + Write DATA Phase Only
+parameter P_FSM_CA     = 4'b0010; // Command -> Address Phase Only
+
+parameter P_FSM_CAR    = 4'b0011; // Command -> Address -> Read Data
+parameter P_FSM_CADR   = 4'b0100; // Command -> Address -> Dummy -> Read Data
+parameter P_FSM_CAMR   = 4'b0101; // Command -> Address -> Mode -> Read Data
+parameter P_FSM_CAMDR  = 4'b0110; // Command -> Address -> Mode -> Dummy -> Read Data
+
+parameter P_FSM_CAW    = 4'b0111; // Command -> Address ->Write Data
+parameter P_FSM_CADW   = 4'b1000; // Command -> Address -> DUMMY + Write Data
+parameter P_FSM_CAMW   = 4'b1001; // Command -> Address -> MODE + Write Data
+
+parameter P_FSM_CDR    = 4'b1010; // COMMAND -> DUMMY -> READ
+parameter P_FSM_CDW    = 4'b1011; // COMMAND -> DUMMY -> WRITE
+parameter P_FSM_CR     = 4'b1100;  // COMMAND -> READ
+
+parameter P_MODE_SWITCH_IDLE     = 2'b00;
+parameter P_MODE_SWITCH_AT_ADDR  = 2'b01;
+parameter P_MODE_SWITCH_AT_DATA  = 2'b10;
+
+parameter P_SINGLE = 2'b00;
+parameter P_DOUBLE = 2'b01;
+parameter P_QUAD   = 2'b10;
+parameter P_QDDR   = 2'b11;
+
+        
+	integer    d_risc_id;
+
+         integer i,j;
+
+
+
+
+	// 50Mhz CLock
+	always #10 clock <= (clock === 1'b0);
+
+	initial begin
+		clock = 0;
+	        flag  = 0;
+                wbd_ext_cyc_i ='h0;  // strobe/request
+                wbd_ext_stb_i ='h0;  // strobe/request
+                wbd_ext_adr_i ='h0;  // address
+                wbd_ext_we_i  ='h0;  // write
+                wbd_ext_dat_i ='h0;  // data output
+                wbd_ext_sel_i ='h0;  // byte enable
+	end
+
+	`ifdef WFDUMP
+	   initial begin
+	   	$dumpfile("simx.vcd");
+	   	$dumpvars(3, arduino_arrays_tb);
+	   	//$dumpvars(0, arduino_arrays_tb.u_top.u_riscv_top.i_core_top_0);
+	   	//$dumpvars(0, arduino_arrays_tb.u_top.u_riscv_top.u_connect);
+	   	//$dumpvars(0, arduino_arrays_tb.u_top.u_riscv_top.u_intf);
+	   	$dumpvars(0, arduino_arrays_tb.u_top.u_pinmux);
+	   end
+       `endif
+
+     /************* Port-D Mapping **********************************
+      *             Arduino-No
+      *   Pin-2        0         PD0/RXD[0]                digital_io[1]
+      *   Pin-3        1         PD1/TXD[0]                digital_io[2]
+      *   Pin-4        2         PD2/RXD[1]/INT0           digital_io[3]
+      *   Pin-5        3         PD3/INT1/OC2B(PWM0)       digital_io[4]
+      *   Pin-6        4         PD4/TXD[1]                digital_io[5]
+      *   Pin-11       5         PD5/SS[3]/OC0B(PWM1)/T1   digital_io[8]
+      *   Pin-12       6         PD6/SS[2]/OC0A(PWM2)/AIN0 digital_io[9]/analog_io[2]
+      *   Pin-13       7         PD7/A1N1                  digital_io[10]/analog_io[3]
+      *   ********************************************************/
+
+     wire [7:0]  port_d_in = {  io_out[10],
+		                        io_out[9],
+		                        io_out[8],
+		                        io_out[5],
+			                    io_out[4],
+			                    io_out[3],
+		                        io_out[2],
+		                        io_out[1]
+			                };
+       
+
+	initial begin
+
+		#200; // Wait for reset removal
+	        repeat (10) @(posedge clock);
+		$display("Monitor: Standalone User Risc Boot Test Started");
+
+		$value$plusargs("risc_core_id=%d", d_risc_id);
+		// Remove Wb Reset
+		wb_user_core_write(`ADDR_SPACE_WBHOST+`WBHOST_GLBL_CFG,'h1);
+
+	    repeat (2) @(posedge clock);
+		#1;
+
+        // Remove WB and SPI Reset, Keep SDARM and CORE under Reset
+        wb_user_core_write(`ADDR_SPACE_PINMUX+`PINMUX_GBL_CFG0,'h01F);
+
+		// QSPI SRAM:CS#2 Switch to QSPI Mode
+        wb_user_core_write(`ADDR_SPACE_WBHOST+`WBHOST_BANK_SEL,'h1000); // Change the Bank Sel 1000
+		wb_user_core_write(`ADDR_SPACE_QSPI+`QSPIM_IMEM_CTRL1,{16'h0,1'b0,1'b0,4'b0000,P_MODE_SWITCH_IDLE,P_SINGLE,P_SINGLE,4'b0100});
+		wb_user_core_write(`ADDR_SPACE_QSPI+`QSPIM_IMEM_CTRL2,{8'h0,2'b00,2'b00,P_FSM_C,8'h00,8'h38});
+		wb_user_core_write(`ADDR_SPACE_QSPI+`QSPIM_IMEM_WDATA,32'h0);
+
+        // Remove all the reset
+        if(d_risc_id == 0) begin
+             $display("STATUS: Working with Risc core 0");
+             wb_user_core_write(`ADDR_SPACE_PINMUX+`PINMUX_GBL_CFG0,'h11F);
+        end else if(d_risc_id == 1) begin
+             $display("STATUS: Working with Risc core 1");
+             wb_user_core_write(`ADDR_SPACE_PINMUX+`PINMUX_GBL_CFG0,'h21F);
+        end else if(d_risc_id == 2) begin
+             $display("STATUS: Working with Risc core 2");
+             wb_user_core_write(`ADDR_SPACE_PINMUX+`PINMUX_GBL_CFG0,'h41F);
+        end else if(d_risc_id == 3) begin
+             $display("STATUS: Working with Risc core 3");
+             wb_user_core_write(`ADDR_SPACE_PINMUX+`PINMUX_GBL_CFG0,'h81F);
+        end
+
+        repeat (100) @(posedge clock);  // wait for Processor Get Ready
+
+
+        repeat (20000) @(posedge clock);  // wait for Processor Get Ready
+        flag = 1;
+
+   fork
+      begin
+         // Refer C code,
+         // Wait for toggle in following sequency 2,7,4,6,5,3
+      
+         portd_detect_pin_toggle(2);
+         portd_detect_pin_toggle(7);
+         portd_detect_pin_toggle(4);
+         portd_detect_pin_toggle(6);
+         portd_detect_pin_toggle(5);
+         portd_detect_pin_toggle(3);
+         
+        
+         // Wait for toggle in following sequency 3,5,6,4,7,2
+         portd_detect_pin_toggle(3);
+         portd_detect_pin_toggle(5);
+         portd_detect_pin_toggle(6);
+         portd_detect_pin_toggle(4);
+         portd_detect_pin_toggle(7);
+         portd_detect_pin_toggle(2);
+      
+          test_fail = 0;
+      end
+      begin
+         repeat (30000) @(posedge clock);  // wait for Processor Get Ready
+         test_fail = 1;
+      end
+      join_any
+
+           #100
+
+
+	   
+	    	$display("###################################################");
+          	if(test_fail == 0) begin
+		   `ifdef GL
+	    	       $display("Monitor: Ardunio arrays  (GL) Passed");
+		   `else
+		       $display("Monitor: Ardunio arrays (RTL) Passed");
+		   `endif
+	        end else begin
+		    `ifdef GL
+	    	        $display("Monitor: Ardunio arrays (GL) Failed");
+		    `else
+		        $display("Monitor: Ardunio arrays (RTL) Failed");
+		    `endif
+		 end
+	    	$display("###################################################");
+	    $finish;
+	end
+
+	initial begin
+		wb_rst_i <= 1'b1;
+		#100;
+		wb_rst_i <= 1'b0;	    	// Release reset
+	end
+wire USER_VDD1V8 = 1'b1;
+wire VSS = 1'b0;
+
+user_project_wrapper u_top(
+`ifdef USE_POWER_PINS
+    .vccd1(USER_VDD1V8),	// User area 1 1.8V supply
+    .vssd1(VSS),	// User area 1 digital ground
+`endif
+    .wb_clk_i        (clock),  // System clock
+    .user_clock2     (1'b1),  // Real-time clock
+    .wb_rst_i        (wb_rst_i),  // Regular Reset signal
+
+    .wbs_cyc_i   (wbd_ext_cyc_i),  // strobe/request
+    .wbs_stb_i   (wbd_ext_stb_i),  // strobe/request
+    .wbs_adr_i   (wbd_ext_adr_i),  // address
+    .wbs_we_i    (wbd_ext_we_i),  // write
+    .wbs_dat_i   (wbd_ext_dat_i),  // data output
+    .wbs_sel_i   (wbd_ext_sel_i),  // byte enable
+
+    .wbs_dat_o   (wbd_ext_dat_o),  // data input
+    .wbs_ack_o   (wbd_ext_ack_o),  // acknowlegement
+
+ 
+    // Logic Analyzer Signals
+    .la_data_in      ('1) ,
+    .la_data_out     (),
+    .la_oenb         ('0),
+ 
+
+    // IOs
+    .io_in          (io_in)  ,
+    .io_out         (io_out) ,
+    .io_oeb         (io_oeb) ,
+
+    .user_irq       () 
+
+);
+
+`ifndef GL // Drive Power for Hold Fix Buf
+    // All standard cell need power hook-up for functionality work
+    initial begin
+
+    end
+`endif    
+
+//------------------------------------------------------
+//  Integrate the Serial flash with qurd support to
+//  user core using the gpio pads
+//  ----------------------------------------------------
+
+   wire flash_clk = io_out[24];
+   wire flash_csb = io_out[25];
+   // Creating Pad Delay
+   wire #1 io_oeb_29 = io_oeb[29];
+   wire #1 io_oeb_30 = io_oeb[30];
+   wire #1 io_oeb_31 = io_oeb[31];
+   wire #1 io_oeb_32 = io_oeb[32];
+   tri  #1 flash_io0 = (io_oeb_29== 1'b0) ? io_out[29] : 1'bz;
+   tri  #1 flash_io1 = (io_oeb_30== 1'b0) ? io_out[30] : 1'bz;
+   tri  #1 flash_io2 = (io_oeb_31== 1'b0) ? io_out[31] : 1'bz;
+   tri  #1 flash_io3 = (io_oeb_32== 1'b0) ? io_out[32] : 1'bz;
+
+   assign io_in[29] = flash_io0;
+   assign io_in[30] = flash_io1;
+   assign io_in[31] = flash_io2;
+   assign io_in[32] = flash_io3;
+
+   // Quard flash
+     s25fl256s #(.mem_file_name("arduino_arrays.ino.hex"),
+	         .otp_file_name("none"),
+                 .TimingModel("S25FL512SAGMFI010_F_30pF")) 
+		 u_spi_flash_256mb (
+           // Data Inputs/Outputs
+       .SI      (flash_io0),
+       .SO      (flash_io1),
+       // Controls
+       .SCK     (flash_clk),
+       .CSNeg   (flash_csb),
+       .WPNeg   (flash_io2),
+       .HOLDNeg (flash_io3),
+       .RSTNeg  (!wb_rst_i)
+
+       );
+
+   wire spiram_csb = io_out[27];
+
+   is62wvs1288 #(.mem_file_name("none"))
+	u_sram (
+         // Data Inputs/Outputs
+           .io0     (flash_io0),
+           .io1     (flash_io1),
+           // Controls
+           .clk    (flash_clk),
+           .csb    (spiram_csb),
+           .io2    (flash_io2),
+           .io3    (flash_io3)
+    );
+
+//-------------------------------------
+
+// detect pin toggle
+task portd_detect_pin_toggle;
+input [7:0] pin_n;
+begin
+   wait(port_d_in[pin_n] == 1'b1);
+   wait(port_d_in[pin_n] == 1'b0);
+   $display("PORT-D Pin : %x Toggle Detected",pin_n);
+
+end
+endtask
+
+
+task wb_user_core_write;
+input [31:0] address;
+input [31:0] data;
+begin
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_adr_i =address;  // address
+  wbd_ext_we_i  ='h1;  // write
+  wbd_ext_dat_i =data;  // data output
+  wbd_ext_sel_i ='hF;  // byte enable
+  wbd_ext_cyc_i ='h1;  // strobe/request
+  wbd_ext_stb_i ='h1;  // strobe/request
+  wait(wbd_ext_ack_o == 1);
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_cyc_i ='h0;  // strobe/request
+  wbd_ext_stb_i ='h0;  // strobe/request
+  wbd_ext_adr_i ='h0;  // address
+  wbd_ext_we_i  ='h0;  // write
+  wbd_ext_dat_i ='h0;  // data output
+  wbd_ext_sel_i ='h0;  // byte enable
+  $display("DEBUG WB USER ACCESS WRITE Address : %x, Data : %x",address,data);
+  repeat (2) @(posedge clock);
+end
+endtask
+
+task  wb_user_core_read;
+input [31:0] address;
+output [31:0] data;
+reg    [31:0] data;
+begin
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_adr_i =address;  // address
+  wbd_ext_we_i  ='h0;  // write
+  wbd_ext_dat_i ='0;  // data output
+  wbd_ext_sel_i ='hF;  // byte enable
+  wbd_ext_cyc_i ='h1;  // strobe/request
+  wbd_ext_stb_i ='h1;  // strobe/request
+  wait(wbd_ext_ack_o == 1);
+  repeat (1) @(negedge clock);
+  data  = wbd_ext_dat_o;  
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_cyc_i ='h0;  // strobe/request
+  wbd_ext_stb_i ='h0;  // strobe/request
+  wbd_ext_adr_i ='h0;  // address
+  wbd_ext_we_i  ='h0;  // write
+  wbd_ext_dat_i ='h0;  // data output
+  wbd_ext_sel_i ='h0;  // byte enable
+  $display("DEBUG WB USER ACCESS READ Address : %x, Data : %x",address,data);
+  repeat (2) @(posedge clock);
+end
+endtask
+
+task  wb_user_core_read_check;
+input [31:0] address;
+output [31:0] data;
+input [31:0] cmp_data;
+reg    [31:0] data;
+begin
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_adr_i =address;  // address
+  wbd_ext_we_i  ='h0;  // write
+  wbd_ext_dat_i ='0;  // data output
+  wbd_ext_sel_i ='hF;  // byte enable
+  wbd_ext_cyc_i ='h1;  // strobe/request
+  wbd_ext_stb_i ='h1;  // strobe/request
+  wait(wbd_ext_ack_o == 1);
+  repeat (1) @(negedge clock);
+  data  = wbd_ext_dat_o;  
+  repeat (1) @(posedge clock);
+  #1;
+  wbd_ext_cyc_i ='h0;  // strobe/request
+  wbd_ext_stb_i ='h0;  // strobe/request
+  wbd_ext_adr_i ='h0;  // address
+  wbd_ext_we_i  ='h0;  // write
+  wbd_ext_dat_i ='h0;  // data output
+  wbd_ext_sel_i ='h0;  // byte enable
+  if(data !== cmp_data) begin
+     $display("ERROR : WB USER ACCESS READ  Address : 0x%x, Exd: 0x%x Rxd: 0x%x ",address,cmp_data,data);
+     test_fail = 1;
+  end else begin
+     $display("STATUS: WB USER ACCESS READ  Address : 0x%x, Data : 0x%x",address,data);
+  end
+  repeat (2) @(posedge clock);
+end
+endtask
+
+`ifdef GL
+
+wire        wbd_spi_stb_i   = u_top.u_qspi_master.wbd_stb_i;
+wire        wbd_spi_ack_o   = u_top.u_qspi_master.wbd_ack_o;
+wire        wbd_spi_we_i    = u_top.u_qspi_master.wbd_we_i;
+wire [31:0] wbd_spi_adr_i   = u_top.u_qspi_master.wbd_adr_i;
+wire [31:0] wbd_spi_dat_i   = u_top.u_qspi_master.wbd_dat_i;
+wire [31:0] wbd_spi_dat_o   = u_top.u_qspi_master.wbd_dat_o;
+wire [3:0]  wbd_spi_sel_i   = u_top.u_qspi_master.wbd_sel_i;
+
+wire        wbd_uart_stb_i  = u_top.u_uart_i2c_usb_spi.reg_cs;
+wire        wbd_uart_ack_o  = u_top.u_uart_i2c_usb_spi.reg_ack;
+wire        wbd_uart_we_i   = u_top.u_uart_i2c_usb_spi.reg_wr;
+wire [8:0]  wbd_uart_adr_i  = u_top.u_uart_i2c_usb_spi.reg_addr;
+wire [7:0]  wbd_uart_dat_i  = u_top.u_uart_i2c_usb_spi.reg_wdata;
+wire [7:0]  wbd_uart_dat_o  = u_top.u_uart_i2c_usb_spi.reg_rdata;
+wire        wbd_uart_sel_i  = u_top.u_uart_i2c_usb_spi.reg_be;
+
+`endif
+
+/**
+`ifdef GL
+//-----------------------------------------------------------------------------
+// RISC IMEM amd DMEM Monitoring TASK
+//-----------------------------------------------------------------------------
+
+`define RISC_CORE  user_uart_tb.u_top.u_core.u_riscv_top
+
+always@(posedge `RISC_CORE.wb_clk) begin
+    if(`RISC_CORE.wbd_imem_ack_i)
+          $display("RISCV-DEBUG => IMEM ADDRESS: %x Read Data : %x", `RISC_CORE.wbd_imem_adr_o,`RISC_CORE.wbd_imem_dat_i);
+    if(`RISC_CORE.wbd_dmem_ack_i && `RISC_CORE.wbd_dmem_we_o)
+          $display("RISCV-DEBUG => DMEM ADDRESS: %x Write Data: %x Resonse: %x", `RISC_CORE.wbd_dmem_adr_o,`RISC_CORE.wbd_dmem_dat_o);
+    if(`RISC_CORE.wbd_dmem_ack_i && !`RISC_CORE.wbd_dmem_we_o)
+          $display("RISCV-DEBUG => DMEM ADDRESS: %x READ Data : %x Resonse: %x", `RISC_CORE.wbd_dmem_adr_o,`RISC_CORE.wbd_dmem_dat_i);
+end
+
+`endif
+**/
+endmodule
+`include "s25fl256s.sv"
+`default_nettype wire