/*
 * SPDX-FileCopyrightText: 2020 Efabless Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 * SPDX-License-Identifier: Apache-2.0
 */

// This include is relative to $CARAVEL_PATH (see Makefile)
#include <defs.h>
#include <stub.c>
#include "ext_reg_map.h"


/*
	Wishbone Test:
		- Configures MPRJ lower 8-IO pins as outputs
		- Checks counter value through the wishbone port
*/
int i = 0; 
int clk = 0;

void main()
{

	int bFail = 0;
	/* 
	IO Control Registers
	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
	| 3-bits | 1-bit | 1-bit | 1-bit  | 1-bit  | 1-bit | 1-bit   | 1-bit   | 1-bit | 1-bit | 1-bit   |
	Output: 0000_0110_0000_1110  (0x1808) = GPIO_MODE_USER_STD_OUTPUT
	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
	| 110    | 0     | 0     | 0      | 0      | 0     | 0       | 1       | 0     | 0     | 0       |
	
	 
	Input: 0000_0001_0000_1111 (0x0402) = GPIO_MODE_USER_STD_INPUT_NOPULL
	| DM     | VTRIP | SLOW  | AN_POL | AN_SEL | AN_EN | MOD_SEL | INP_DIS | HOLDH | OEB_N | MGMT_EN |
	| 001    | 0     | 0     | 0      | 0      | 0     | 0       | 0       | 0     | 1     | 0       |
	*/

	/* Set up the housekeeping SPI to be connected internally so	*/
	/* that external pin changes don't affect it.			*/

    reg_spi_enable = 0;
    reg_wb_enable = 1;
	// reg_spimaster_config = 0xa002;	// Enable, prescaler = 2,
                                        // connect to housekeeping SPI

	// Connect the housekeeping SPI to the SPI master
	// so that the CSB line is not left floating.  This allows
	// all of the GPIO pins to be used for user functions.

    reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;

     /* Apply configuration */
    reg_mprj_xfer = 1;
    while (reg_mprj_xfer == 1);

    reg_la0_oenb = reg_la0_iena = 0xFFFFFFFF;    // [31:0]
    reg_la0_data = 0x000;
    reg_la0_data = 0x001; // Remove Soft Reset

    // Flag start of the test
	reg_mprj_datal = 0xAB600000;

    // Remove Wishbone Reset
    reg_mprj_wbhost_ctrl = 0x1;

    // Remove Reset
    reg_glbl_cfg0 = 0x01f;

    if (reg_glbl_chip_id != 0x82682501) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB610000;

    // write software write & read Register
    reg_glbl_soft_reg_0  = 0x11223344; 
    reg_glbl_soft_reg_1  = 0x22334455; 
    reg_glbl_soft_reg_2  = 0x33445566; 
    reg_glbl_soft_reg_3  = 0x44556677; 
    reg_glbl_soft_reg_4  = 0x55667788; 
    reg_glbl_soft_reg_5  = 0x66778899; 


    if (reg_glbl_soft_reg_0  != 0x11223344) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB620000;
    if (reg_glbl_soft_reg_1  != 0x22334455) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB630000;
    if (reg_glbl_soft_reg_2  != 0x33445566) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB640000;
    if (reg_glbl_soft_reg_3  != 0x44556677) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB650000;
    if (reg_glbl_soft_reg_4 != 0x55667788) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB660000;
    if (reg_glbl_soft_reg_5 != 0x66778899) bFail = 1;
    if (bFail == 1) reg_mprj_datal = 0xAB670000;

    if(bFail == 0) {
        reg_mprj_datal = 0xAB6A0000;
    } else {
        reg_mprj_datal = 0xAB600000;
    }
}