// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none

`timescale 1 ns / 1 ps

`define PER 20 // period


module wb_sec_mon_tb ();
  reg clock ;
  reg RSTB  ;
  reg CSB   ;
  reg power1, power2;
  reg power3, power4;

  wire        gpio     ;
  wire [37:0] mprj_io  ;
  wire [ 7:0] mprj_io_0;
  wire [11:0] checkbits;


  reg attack;


  assign checkbits = mprj_io[31:20];

  assign mprj_io[3] = 1'b1;

  assign mprj_io[17] = attack ? 1'b0 : rx;

  wire rx;
  assign rx = uut.mprj.io_out[18];  //assign mprj_io[17] = rx;

  // External clock is used by default.  Make this artificially fast for the
  // simulation.  Normally this would be a slow clock and the digital PLL
  // would be the fast clock.

  //50MHz
  always #(`PER/2) clock <= (clock === 1'b0);

  initial
    begin
      clock = 0;
      attack = 0;
      repeat(20000) @(posedge clock);
      attack = 1;
      repeat(20) @(posedge clock);
      attack = 0;

    end

  initial
    begin
      $dumpfile("wb_sec_mon.vcd");
      $dumpvars(0, wb_sec_mon_tb);

      // Repeat cycles of 1000 clock edges as needed to complete testbench
      repeat (70)
        begin
          repeat (500) @(posedge clock);
          // $display("+1000 cycles");
        end
      $display("%c[1;31m",27);
`ifdef GL

      $display ("Monitor: Timeout, Test Mega-Project WB Port (GL) Failed");
`else
      $display ("Monitor: Timeout, Test Mega-Project WB Port (RTL) Failed");
`endif

      $display("%c[0m",27);
      $finish;
    end


  initial
    begin 
      wait(checkbits[15:4] == 12'hAB6);
    end


  initial
    begin
     
      
      wait(checkbits[15:4] == 12'hAB7 || checkbits[15:4] == 12'hAB8 );

      if(checkbits[15:4] == 12'hAB8)
        begin
          $display("Alarm Detected!");
          $finish;
        end
        else
          begin
    `ifdef GL
            $display("Monitor: Mega-Project WB (GL) Passed");
    `else
            $display("Monitor: Mega-Project WB (RTL) Passed");
    `endif
            $finish;
          end
    end

  initial
    begin
      RSTB <= 1'b0;
      CSB  <= 1'b1;		// Force CSB high
      #10000;
      RSTB <= 1'b1;	    	// Release reset
      #100000;
      CSB = 1'b0;		// CSB can be released
    end

  initial
    begin		// Power-up sequence
      power1 <= 1'b0;
      power2 <= 1'b0;
      #200;
      power1 <= 1'b1;
      #200;
      power2 <= 1'b1;
    end


  wire flash_csb;
  wire flash_clk;
  wire flash_io0;
  wire flash_io1;

  wire VDD3V3      = power1;
  wire VDD1V8      = power2;
  wire USER_VDD3V3 = power3;
  wire USER_VDD1V8 = power4;
  wire VSS         = 1'b0  ;

  caravel uut (
    .vddio    (VDD3V3   ),
    .vddio_2  (VDD3V3   ),
    .vssio    (VSS      ),
    .vssio_2  (VSS      ),
    .vdda     (VDD3V3   ),
    .vssa     (VSS      ),
    .vccd     (VDD1V8   ),
    .vssd     (VSS      ),
    .vdda1    (VDD3V3   ),
    .vdda1_2  (VDD3V3   ),
    .vdda2    (VDD3V3   ),
    .vssa1    (VSS      ),
    .vssa1_2  (VSS      ),
    .vssa2    (VSS      ),
    .vccd1    (VDD1V8   ),
    .vccd2    (VDD1V8   ),
    .vssd1    (VSS      ),
    .vssd2    (VSS      ),
    .clock    (clock    ),
    .gpio     (gpio     ),
    .mprj_io  (mprj_io  ),
    .flash_csb(flash_csb),
    .flash_clk(flash_clk),
    .flash_io0(flash_io0),
    .flash_io1(flash_io1),
    .resetb   (RSTB     )
  );

  spiflash #(.FILENAME("wb_sec_mon.hex")) spiflash (
    .csb(flash_csb),
    .clk(flash_clk),
    .io0(flash_io0),
    .io1(flash_io1),
    .io2(         ), // not used
    .io3(         )  // not used
  );


endmodule

`default_nettype wire