// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *-------------------------------------------------------------
 *
 * user_proj_example
 *
 * This is an example of a (trivially simple) user project,
 * showing how the user project can connect to the logic
 * analyzer, the wishbone bus, and the I/O pads.
 *
 * This project generates an integer count, which is output
 * on the user area GPIO pads (digital output only).  The
 * wishbone connection allows the project to be controlled
 * (start and stop) from the management SoC program.
 *
 * See the testbenches in directory "mprj_counter" for the
 * example programs that drive this user project.  The three
 * testbenches are "io_ports", "la_test1", and "la_test2".
 *
 *-------------------------------------------------------------
 */

module user_proj_example #(
    parameter BITS = 32
)(
`ifdef USE_POWER_PINS
    inout vccd1,	// User area 1 1.8V supply
    inout vssd1,	// User area 1 digital ground
`endif

    // Wishbone Slave ports (WB MI A)
    input wb_clk_i,
    input wb_rst_i,
    input wbs_stb_i,
    input wbs_cyc_i,
    input wbs_we_i,
    input [3:0] wbs_sel_i,
    input [31:0] wbs_dat_i,
    input [31:0] wbs_adr_i,
    output wbs_ack_o,
    output [31:0] wbs_dat_o,

    // Logic Analyzer Signals
    input  [127:0] la_data_in,
    output [127:0] la_data_out,
    input  [127:0] la_oenb,

    // IOs
    input  [`MPRJ_IO_PADS-1:0] io_in,
    output [`MPRJ_IO_PADS-1:0] io_out,
    output [`MPRJ_IO_PADS-1:0] io_oeb,

    // IRQ
    output [2:0] irq,

    output                                          vb_csb0                 ,
    output                                          vb_web0                 ,
    output          [3:0]                           vb_wmask0               ,
    output          [12:0]                          vb_addr0                ,
    output          [31:0]                          vb_din0                 ,
    input           [31:0]                          vb_dout0                ,

    output                                          vb_csb1                 ,
    output          [12:0]                          vb_addr1                ,
    input           [31:0]                          vb_dout1                ,

    output                                          bb_csb0                 ,
    output                                          bb_web0                 ,
    output          [3:0]                           bb_wmask0               ,
    output          [31:0]                          bb_addr0                ,
    output          [31:0]                          bb_din0                 ,
    input           [31:0]                          bb_dout0                ,

    output                                          bb_csb1                 ,
    output          [31:0]                          bb_addr1                ,
    input           [31:0]                          bb_dout1                         
);
    wire clk;
    wire rst;

    wire [`MPRJ_IO_PADS-1:0] io_in;
    wire [`MPRJ_IO_PADS-1:0] io_out;
    wire [`MPRJ_IO_PADS-1:0] io_oeb;

    wire [31:0] rdata; 
    wire [31:0] wdata;
    wire [BITS-1:0] count;

    wire valid;
    wire [3:0] wstrb;
    wire [31:0] la_write;

    // WB MI A
    assign valid = wbs_cyc_i && wbs_stb_i; 
    assign wstrb = wbs_sel_i & {4{wbs_we_i}};
    assign wbs_dat_o = rdata;
    assign wdata = wbs_dat_i;

    // IO
    assign io_out = count;
    assign io_oeb = {(`MPRJ_IO_PADS-1){rst}};

    // IRQ
    assign irq = 3'b000;	// Unused

    // LA
    assign la_data_out = {{(127-BITS){1'b0}}, count};
    // Assuming LA probes [63:32] are for controlling the count register  
    assign la_write = ~la_oenb[63:32] & ~{BITS{valid}};
    // Assuming LA probes [65:64] are for controlling the count clk & reset  
    assign clk = (~la_oenb[64]) ? la_data_in[64]: wb_clk_i;
    assign rst = (~la_oenb[65]) ? la_data_in[65]: wb_rst_i;

    c0_system c0_system(
        .clk_g(clk),
        .rst_g(rst),
        .ready(wbs_ack_o),
        .valid(valid),
        .rdata(rdata),
        .wdata(wbs_dat_i),
        .wstrb(wstrb),
        .la_write(la_write),
        .la_input(la_data_in[63:32]),
        .count(count),
        .tx(tx),
        .rx(rx),
        .io_gecerli(io_gecerli),
        .io_ps(io_ps),
        
        .bb_csb0                                           (bb_csb0)                                                       ,
        .bb_web0                                           (bb_web0)                                                       ,
        .bb_wmask0                                         (bb_wmask0)                                                     ,
        .bb_addr0                                          (bb_addr0)                                                      ,
        .bb_din0                                           (bb_din0)                                                       ,
        .bb_dout0                                          (bb_dout0)                                                      ,

        .bb_csb1                                           (bb_csb1)                                                       ,
        .bb_addr1                                          (bb_addr1)                                                      ,
        .bb_dout1                                          (bb_dout1)                                                      ,

        .vb_csb0                                           (vb_csb0)                                                       ,
        .vb_web0                                           (vb_web0)                                                       ,
        .vb_wmask0                                         (vb_wmask0)                                                     ,
        .vb_addr0                                          (vb_addr0)                                                      ,
        .vb_din0                                           (vb_din0)                                                       ,
        .vb_dout0                                          (vb_dout0)                                                      ,

        .vb_csb1                                           (vb_csb1)                                                       ,
        .vb_addr1                                          (vb_addr1)                                                      ,
        .vb_dout1                                          (vb_dout1) 
    );

endmodule
`default_nettype wire