/*
 * SPDX-FileCopyrightText: 2020 Efabless Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 * SPDX-License-Identifier: Apache-2.0
 */

// This include is relative to $CARAVEL_PATH (see Makefile)
#include "verilog/dv/caravel/defs.h"
#include "verilog/dv/caravel/stub.c"

/*
	MPRJ LA Test:
		- Sets counter clk through LA[64]
		- Sets counter rst through LA[65] 
		- Observes count value for five clk cycle through LA[31:0]
*/

int clk = 0;
int i;

void main()
{
        /* Set up the housekeeping SPI to be connected internally so	*/
	/* that external pin changes don't affect it.			*/

	reg_spimaster_config = 0xa002;	// Enable, prescaler = 2,
                                        // connect to housekeeping SPI

	// Connect the housekeeping SPI to the SPI master
	// so that the CSB line is not left floating.  This allows
	// all of the GPIO pins to be used for user functions.


	// All GPIO pins are configured to be output
	// Used to flad the start/end of a test 

        reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
        reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;

        reg_mprj_io_15 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_14 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_13 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_12 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_11 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_10 = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_9  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_8  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_7  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_5  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_4  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_3  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_2  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_1  = GPIO_MODE_USER_STD_OUTPUT;
        reg_mprj_io_0  = GPIO_MODE_USER_STD_OUTPUT;

        /* Apply configuration */
        reg_mprj_xfer = 1;
        while (reg_mprj_xfer == 1);

	// Configure All LA probes as inputs to the cpu 
	reg_la0_oenb = reg_la0_iena = 0xFFFFFFFF;    // [31:0]
	reg_la1_oenb = reg_la1_iena = 0xFFFFFFFF;    // [63:32]
	reg_la2_oenb = reg_la2_iena = 0xFFFFFFFF;    // [95:64]
	reg_la3_oenb = reg_la3_iena = 0xFFFFFFFF;    // [127:96]

	// Flag start of the test
	reg_mprj_datal = 0xAB600000;

	// Configure LA[64] LA[65] as outputs from the cpu
	reg_la2_oenb = reg_la2_iena = 0xFFFFFFFC; 

	// Set clk & reset to one
	reg_la2_data = 0x00000003;

        // DELAY
        for (i=0; i<5; i=i+1) {}

	// Toggle clk & de-assert reset
	for (i=0; i<11; i=i+1) {
		clk = !clk;
		reg_la2_data = 0x00000000 | clk;
	}

	if (reg_la0_data >= 0x05) {
		reg_mprj_datal = 0xAB610000;
	}

}