// `default_nettype none
// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0
/*--------------------------------------------------------------*/
/* caravan, a project harness for the Google/SkyWater sky130	*/
/* fabrication process and open source PDK.  caravan is an 	*/
/* alternative architecture to caravel that has simple straight	*/
/* through connections replacing the GPIO pads on the top side	*/
/* of the padframe.  A total of 11 pads are converted from GPIO	*/
/* to analog, leaving 27 GPIO.					*/
/*                                                          	*/
/* Copyright 2021 efabless, Inc.                            	*/
/* Written by Tim Edwards, December 2019                    	*/
/* and Mohamed Shalan, August 2020			    	*/
/* This file is open source hardware released under the     	*/
/* Apache 2.0 license.  See file LICENSE.                   	*/
/*                                                          	*/
/*--------------------------------------------------------------*/

/*--------------------------------------------------------------*/
/* Derived types for the array bounds on the two digital and	*/
/* two analog pad arrays.  As defined above, the sections have	*/
/* the number of pads as follows:				*/
/*								*/
/*	DIG2 : 13 GPIO pads					*/
/*	ANA2 : 6  analog pads					*/
/*	ANA1 : 5  analog pads					*/
/*	DIG1 : 14 GPIO pads					*/
/*								*/
/* This makes a total of 38 pads = `MPRJ_IO_PADS		*/
/* The pads are still designated as mprj_io[37:0] around the	*/
/* padframe.  The SoC core remains the same, so the programming	*/
/* of the digital signals remains the same, but the values for	*/
/* GPIO 15-25 are not used.					*/
/*--------------------------------------------------------------*/

`define DIG2_TOP (`MPRJ_IO_PADS - 1)
`define DIG2_BOT (`MPRJ_IO_PADS_1 + `ANALOG_PADS_2)
`define ANA2_TOP (`MPRJ_IO_PADS_1 + `ANALOG_PADS_2 - 1)
`define ANA2_BOT (`MPRJ_IO_PADS_1)
`define ANA1_TOP (`MPRJ_IO_PADS_1 - 1)
`define ANA1_BOT (`MPRJ_IO_PADS_1 - `ANALOG_PADS_1)
`define DIG1_TOP (`MPRJ_IO_PADS_1 - `ANALOG_PADS_1 - 1)
`define DIG1_BOT (0)

`define MPRJ_DIG_PADS (`MPRJ_IO_PADS - `ANALOG_PADS)

/*--------------------------------------------------------------*/
/*--------------------------------------------------------------*/

module caravan (
    inout vddio,	// Common 3.3V padframe/ESD power
    inout vddio_2,	// Common 3.3V padframe/ESD power
    inout vssio,	// Common padframe/ESD ground
    inout vssio_2,	// Common padframe/ESD ground
    inout vdda,		// Management 3.3V power
    inout vssa,		// Common analog ground
    inout vccd,		// Management/Common 1.8V power
    inout vssd,		// Common digital ground
    inout vdda1,	// User area 1 3.3V power
    inout vdda1_2,	// User area 1 3.3V power
    inout vdda2,	// User area 2 3.3V power
    inout vssa1,	// User area 1 analog ground
    inout vssa1_2,	// User area 1 analog ground
    inout vssa2,	// User area 2 analog ground
    inout vccd1,	// User area 1 1.8V power
    inout vccd2,	// User area 2 1.8V power
    inout vssd1,	// User area 1 digital ground
    inout vssd2,	// User area 2 digital ground

    inout gpio,			// Used for external LDO control
    inout [`MPRJ_IO_PADS-1:0] mprj_io,
    input clock,	    	// CMOS core clock input, not a crystal
    input resetb,

    // Note that only two pins are available on the flash so dual and
    // quad flash modes are not available.

    output flash_csb,
    output flash_clk,
    output flash_io0,
    output flash_io1
);

    //------------------------------------------------------------
    // This value is uniquely defined for each user project.
    //------------------------------------------------------------
    parameter USER_PROJECT_ID = 32'h00000000;

    /*
     *---------------------------------------------------------------------
     * These pins are overlaid on mprj_io space.  They have the function
     * below when the management processor is in reset, or in the default
     * configuration.  They are assigned to uses in the user space by the
     * configuration program running off of the SPI flash.  Note that even
     * when the user has taken control of these pins, they can be restored
     * to the original use by setting the resetb pin low.  The SPI pins and
     * UART pins can be connected directly to an FTDI chip as long as the
     * FTDI chip sets these lines to high impedence (input function) at
     * all times except when holding the chip in reset.
     *
     * JTAG      = mprj_io[0]		(inout)
     * SDO 	 = mprj_io[1]		(output)
     * SDI 	 = mprj_io[2]		(input)
     * CSB 	 = mprj_io[3]		(input)
     * SCK	 = mprj_io[4]		(input)
     * ser_rx    = mprj_io[5]		(input)
     * ser_tx    = mprj_io[6]		(output)
     * irq 	 = mprj_io[7]		(input)
     *
     * spi_sck    = mprj_io[32]         (output)
     * spi_csb    = mprj_io[33]         (output)
     * spi_sdi    = mprj_io[34]         (input)
     * spi_sdo    = mprj_io[35]         (output)
     * flash_io2  = mprj_io[36]         (inout)
     * flash_io3  = mprj_io[37]         (inout)
     *
     * These pins are reserved for any project that wants to incorporate
     * its own processor and flash controller.  While a user project can
     * technically use any available I/O pins for the purpose, these
     * four pins connect to a pass-through mode from the SPI slave (pins
     * 1-4 above) so that any SPI flash connected to these specific pins
     * can be accessed through the SPI slave even when the processor is in
     * reset.
     *
     * user_flash_csb = mprj_io[8]
     * user_flash_sck = mprj_io[9]
     * user_flash_io0 = mprj_io[10]
     * user_flash_io1 = mprj_io[11]
     *
     *---------------------------------------------------------------------
     */

    // One-bit GPIO dedicated to management SoC (outside of user control)
    wire gpio_out_core;
    wire gpio_in_core;
    wire gpio_mode0_core;
    wire gpio_mode1_core;
    wire gpio_outenb_core;
    wire gpio_inenb_core;

    // 27 GPIO pads with full controls
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_inp_dis;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_oeb;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_ib_mode_sel;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_vtrip_sel;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_slow_sel;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_holdover;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_analog_en;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_analog_sel;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_analog_pol;
    wire [(`MPRJ_IO_PADS-`ANALOG_PADS)*3-1:0] mprj_io_dm;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_in;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_in_3v3;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] mprj_io_out;

    // User Project Control (user-facing)
    // 27 GPIO bidirectional with in/out/oeb and a 3.3V copy of the input
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] user_io_oeb;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] user_io_in;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] user_io_out;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-1:0] user_io_in_3v3;

    // 18 direct connections to GPIO for low-frequency, low-voltage analog
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-10:0] user_gpio_analog;
    wire [`MPRJ_IO_PADS-`ANALOG_PADS-10:0] user_gpio_noesd;

    // 3 power supply ESD clamps for user applications
    wire [2:0] user_clamp_high;
    wire [2:0] user_clamp_low;

    // 11 core connections to the analog pads
    wire [`ANALOG_PADS-1:0] user_analog;

    /* Padframe control signals */
    wire [`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1:0] gpio_serial_link_1;
    wire [`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1:0] gpio_serial_link_2;
    wire mprj_io_loader_resetn;
    wire mprj_io_loader_clock;
    wire mprj_io_loader_strobe;
    wire mprj_io_loader_data_1;		/* user1 side serial loader */
    wire mprj_io_loader_data_2;		/* user2 side serial loader */

    // User Project Control management I/O
    // There are two types of GPIO connections:
    // (1) Full Bidirectional: Management connects to in, out, and oeb
    //     Uses:  JTAG and SDO
    // (2) Selectable bidirectional:  Management connects to in and out,
    //	   which are tied together.  oeb is grounded (oeb from the
    //	   configuration is used)

    // SDI 	 = mprj_io[2]		(input)
    // CSB 	 = mprj_io[3]		(input)
    // SCK	 = mprj_io[4]		(input)
    // ser_rx    = mprj_io[5]		(input)
    // ser_tx    = mprj_io[6]		(output)
    // irq 	 = mprj_io[7]		(input)

    wire [`MPRJ_IO_PADS-1:0] mgmt_io_in;	/* one- and three-pin data */
    wire [`MPRJ_IO_PADS-1:0] mgmt_io_nc;	/* no-connects */
    wire [4:0] mgmt_io_out;			/* three-pin interface out */
    wire [4:0] mgmt_io_oeb;			/* three-pin output enable */
    wire [`MPRJ_PWR_PADS-1:0] pwr_ctrl_nc;	/* no-connects */

    wire clock_core;

    // Power-on-reset signal.  The reset pad generates the sense-inverted
    // reset at 3.3V.  The 1.8V signal and the inverted 1.8V signal are
    // derived.

    wire porb_h;
    wire porb_l;
    wire por_l;

    wire rstb_h;
    wire rstb_l;

    // Flash SPI communication (managment SoC to housekeeping)
    wire flash_clk_core,     flash_csb_core;
    wire flash_clk_oeb_core, flash_csb_oeb_core;
    wire flash_clk_ieb_core, flash_csb_ieb_core;
    wire flash_io0_oeb_core, flash_io1_oeb_core;
    wire flash_io2_oeb_core, flash_io3_oeb_core;
    wire flash_io0_ieb_core, flash_io1_ieb_core;
    wire flash_io2_ieb_core, flash_io3_ieb_core;
    wire flash_io0_do_core,  flash_io1_do_core;
    wire flash_io2_do_core,  flash_io3_do_core;
    wire flash_io0_di_core,  flash_io1_di_core;
    wire flash_io2_di_core,  flash_io3_di_core;

    // Flash SPI communication
    wire flash_clk_frame;
    wire flash_csb_frame;
    wire flash_clk_oeb, flash_csb_oeb;
    wire flash_clk_ieb, flash_csb_ieb;
    wire flash_io0_oeb, flash_io1_oeb;
    wire flash_io0_ieb, flash_io1_ieb;
    wire flash_io0_do,  flash_io1_do;
    wire flash_io0_di,  flash_io1_di;

    chip_io_alt #(
	.ANALOG_PADS_1(`ANALOG_PADS_1),
	.ANALOG_PADS_2(`ANALOG_PADS_2)
    ) padframe (
	`ifndef TOP_ROUTING
		// Package Pins
		.vddio_pad	(vddio),		// Common padframe/ESD supply
		.vddio_pad2	(vddio_2),
		.vssio_pad	(vssio),		// Common padframe/ESD ground
		.vssio_pad2	(vssio_2),
		.vccd_pad	(vccd),			// Common 1.8V supply
		.vssd_pad	(vssd),			// Common digital ground
		.vdda_pad	(vdda),			// Management analog 3.3V supply
		.vssa_pad	(vssa),			// Management analog ground
		.vdda1_pad	(vdda1),		// User area 1 3.3V supply
		.vdda1_pad2	(vdda1_2),		
		.vdda2_pad	(vdda2),		// User area 2 3.3V supply
		.vssa1_pad	(vssa1),		// User area 1 analog ground
		.vssa1_pad2	(vssa1_2),
		.vssa2_pad	(vssa2),		// User area 2 analog ground
		.vccd1_pad	(vccd1),		// User area 1 1.8V supply
		.vccd2_pad	(vccd2),		// User area 2 1.8V supply
		.vssd1_pad	(vssd1),		// User area 1 digital ground
		.vssd2_pad	(vssd2),		// User area 2 digital ground
	`endif
	
	// Core Side Pins
	.vddio	(vddio_core),
	.vssio	(vssio_core),
	.vdda	(vdda_core),
	.vssa	(vssa_core),
	.vccd	(vccd_core),
	.vssd	(vssd_core),
	.vdda1	(vdda1_core),
	.vdda2	(vdda2_core),
	.vssa1	(vssa1_core),
	.vssa2	(vssa2_core),
	.vccd1	(vccd1_core),
	.vccd2	(vccd2_core),
	.vssd1	(vssd1_core),
	.vssd2	(vssd2_core),

	.gpio(gpio),
	.mprj_io(mprj_io),
	.clock(clock),
	.resetb(resetb),
	.flash_csb(flash_csb),
	.flash_clk(flash_clk),
	.flash_io0(flash_io0),
	.flash_io1(flash_io1),
	// SoC Core Interface
	.porb_h(porb_h),
	.por(por_l),
	.resetb_core_h(rstb_h),
	.clock_core(clock_core),
	.gpio_out_core(gpio_out_core),
	.gpio_in_core(gpio_in_core),
	.gpio_mode0_core(gpio_mode0_core),
	.gpio_mode1_core(gpio_mode1_core),
	.gpio_outenb_core(gpio_outenb_core),
	.gpio_inenb_core(gpio_inenb_core),
	.flash_csb_core(flash_csb_frame),
	.flash_clk_core(flash_clk_frame),
	.flash_csb_oeb_core(flash_csb_oeb),
	.flash_clk_oeb_core(flash_clk_oeb),
	.flash_io0_oeb_core(flash_io0_oeb),
	.flash_io1_oeb_core(flash_io1_oeb),
	.flash_csb_ieb_core(flash_csb_ieb),
	.flash_clk_ieb_core(flash_clk_ieb),
	.flash_io0_ieb_core(flash_io0_ieb),
	.flash_io1_ieb_core(flash_io1_ieb),
	.flash_io0_do_core(flash_io0_do),
	.flash_io1_do_core(flash_io1_do),
	.flash_io0_di_core(flash_io0_di),
	.flash_io1_di_core(flash_io1_di),
	.mprj_io_in(mprj_io_in),
	.mprj_io_in_3v3(mprj_io_in_3v3),
	.mprj_io_out(mprj_io_out),
	.mprj_io_oeb(mprj_io_oeb),
	.mprj_io_inp_dis(mprj_io_inp_dis),
	.mprj_io_ib_mode_sel(mprj_io_ib_mode_sel),
	.mprj_io_vtrip_sel(mprj_io_vtrip_sel),
	.mprj_io_slow_sel(mprj_io_slow_sel),
	.mprj_io_holdover(mprj_io_holdover),
	.mprj_io_analog_en(mprj_io_analog_en),
	.mprj_io_analog_sel(mprj_io_analog_sel),
	.mprj_io_analog_pol(mprj_io_analog_pol),
	.mprj_io_dm(mprj_io_dm),
	.mprj_gpio_analog(user_gpio_analog),
	.mprj_gpio_noesd(user_gpio_noesd),
	.mprj_analog(user_analog),
	.mprj_clamp_high(user_clamp_high),
	.mprj_clamp_low(user_clamp_low)
    );

    // SoC core
    wire caravel_clk;
    wire caravel_clk2;
    wire caravel_rstn;

    wire [7:0] spi_ro_config_core;

    // LA signals
    wire [127:0] la_data_in_user;  // From CPU to MPRJ
    wire [127:0] la_data_in_mprj;  // From MPRJ to CPU
    wire [127:0] la_data_out_mprj; // From CPU to MPRJ
    wire [127:0] la_data_out_user; // From MPRJ to CPU
    wire [127:0] la_oenb_user;     // From CPU to MPRJ
    wire [127:0] la_oenb_mprj;	   // From CPU to MPRJ
    wire [127:0] la_iena_mprj;     // From CPU only

    wire [2:0]   user_irq;	   // From MPRJ to CPU
    wire [2:0]   user_irq_core;
    wire [2:0]   user_irq_ena;
    wire [2:0]	 irq_spi;	   // From SPI and external pins

    // Exported Wishbone Bus (processor facing)
    wire mprj_cyc_o_core;
    wire mprj_stb_o_core;
    wire mprj_we_o_core;
    wire [3:0] mprj_sel_o_core;
    wire [31:0] mprj_adr_o_core;
    wire [31:0] mprj_dat_o_core;
    wire 	mprj_ack_i_core;
    wire [31:0] mprj_dat_i_core;

    wire [31:0] hk_dat_i;
    wire hk_ack_i;
    wire hk_stb_o;
    wire hk_cyc_o;

    // Exported Wishbone Bus (user area facing)
    wire 	mprj_cyc_o_user;
    wire 	mprj_stb_o_user;
    wire 	mprj_we_o_user;
    wire [3:0]  mprj_sel_o_user;
    wire [31:0] mprj_adr_o_user;
    wire [31:0] mprj_dat_o_user;
    wire 	mprj_ack_i_user;
    wire [31:0]	mprj_dat_i_user;

    // Mask revision
    wire [31:0] mask_rev;

    wire 	mprj_clock;
    wire 	mprj_clock2;
    wire 	mprj_reset;

    // Power monitoring
    wire	mprj_vcc_pwrgood;
    wire	mprj2_vcc_pwrgood;
    wire	mprj_vdd_pwrgood;
    wire	mprj2_vdd_pwrgood;

    // SRAM read-noly access from housekeeping
    wire 	hkspi_sram_clk;
    wire	hkspi_sram_csb;
    wire [7:0]  hkspi_sram_addr;
    wire [31:0] hkspi_sram_data;

    // Management processor (wrapper).  Any management core
    // implementation must match this pinout.

    mgmt_core_wrapper soc (
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif

	// Clocks and reset
       	.core_clk(caravel_clk),
       	.core_rstn(caravel_rstn),

	// GPIO (1 pin)
	.gpio_out_pad(gpio_out_core),
	.gpio_in_pad(gpio_in_core),
	.gpio_mode0_pad(gpio_mode0_core),
	.gpio_mode1_pad(gpio_mode1_core),
	.gpio_outenb_pad(gpio_outenb_core),
	.gpio_inenb_pad(gpio_inenb_core),

	// Primary SPI flash controller
	.flash_csb(flash_csb_core),
	.flash_clk(flash_clk_core),
	.flash_io0_oeb(flash_io0_oeb_core),
	.flash_io0_di(flash_io0_di_core),
	.flash_io0_do(flash_io0_do_core),
	.flash_io1_oeb(flash_io1_oeb_core),
	.flash_io1_di(flash_io1_di_core),
	.flash_io1_do(flash_io1_do_core),
	.flash_io2_oeb(flash_io2_oeb_core),
	.flash_io2_di(flash_io2_di_core),
	.flash_io2_do(flash_io2_do_core),
	.flash_io3_oeb(flash_io3_oeb_core),
	.flash_io3_di(flash_io3_di_core),
	.flash_io3_do(flash_io3_do_core),

	// Exported Wishbone Bus
	.mprj_cyc_o(mprj_cyc_o_core),
	.mprj_stb_o(mprj_stb_o_core),
	.mprj_we_o(mprj_we_o_core),
	.mprj_sel_o(mprj_sel_o_core),
	.mprj_adr_o(mprj_adr_o_core),
	.mprj_dat_o(mprj_dat_o_core),
	.mprj_ack_i(mprj_ack_i_core),
	.mprj_dat_i(mprj_dat_i_core),

	.hk_stb_o(hk_stb_o),
	.hk_cyc_o(hk_cyc_o),
	.hk_dat_i(hk_dat_i),
	.hk_ack_i(hk_ack_i),

	// IRQ
	.irq({irq_spi, user_irq}),

	// Module status (these may or may not be implemented)
	.qspi_enabled(qspi_enabled),
	.uart_enabled(uart_enabled),
	.spi_enabled(spi_enabled),
	.debug_mode(debug_mode),

	// Module I/O (these may or may not be implemented)
	// UART
	.ser_tx(ser_tx),
	.ser_rx(ser_rx),
	// SPI master
	.spi_sdi(spi_sdi),
	.spi_csb(spi_csb),
	.spi_sck(spi_sck),
	.spi_sdo(spi_sdo),
	.spi_sdoenb(spi_sdoenb),
	// Debug
	.debug_in(debug_in),
	.debug_out(debug_out),
	.debug_oeb(debug_oeb),
	// Logic analyzer
	.la_input(la_data_in_mprj),
	.la_output(la_data_out_mprj),
	.la_oenb(la_oenb_mprj),
	.la_iena(la_iena_mprj),

	// SRAM Read-only access from housekeeping
	.sram_ro_clk(hkspi_sram_clk),
	.sram_ro_csb(hkspi_sram_csb),
	.sram_ro_addr(hkspi_sram_addr),
	.sram_ro_data(hkspi_sram_data),

	// Trap status
	.trap(trap)
    );

    /* Clock and reset to user space are passed through a tristate	*/
    /* buffer like the above, but since they are intended to be		*/
    /* always active, connect the enable to the logic-1 output from	*/
    /* the vccd1 domain.						*/

    mgmt_protect mgmt_buffers (
	`ifdef USE_POWER_PINS
	    .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
	    .vccd2(vccd2_core),
	    .vssd2(vssd2_core),
	    .vdda1(vdda1_core),
	    .vssa1(vssa1_core),
	    .vdda2(vdda2_core),
	    .vssa2(vssa2_core),
	`endif
	.caravel_clk(caravel_clk),
	.caravel_clk2(caravel_clk2),
	.caravel_rstn(caravel_rstn),
	.mprj_iena_wb(mprj_iena_wb),
	.mprj_cyc_o_core(mprj_cyc_o_core),
	.mprj_stb_o_core(mprj_stb_o_core),
	.mprj_we_o_core(mprj_we_o_core),
	.mprj_sel_o_core(mprj_sel_o_core),
	.mprj_adr_o_core(mprj_adr_o_core),
	.mprj_dat_o_core(mprj_dat_o_core),
	.mprj_dat_i_core(mprj_dat_i_core),
	.mprj_ack_i_core(mprj_ack_i_core),
	.user_irq_core(user_irq_core),
	.la_data_out_core(la_data_out_user),
	.la_data_out_mprj(la_data_out_mprj),
	.la_data_in_core(la_data_in_user),
	.la_data_in_mprj(la_data_in_mprj),
	.la_oenb_mprj(la_oenb_mprj),
	.la_oenb_core(la_oenb_user),
	.la_iena_mprj(la_iena_mprj),
	.user_irq_ena(user_irq_ena),

	.user_clock(mprj_clock),
	.user_clock2(mprj_clock2),
	.user_reset(mprj_reset),
	.mprj_cyc_o_user(mprj_cyc_o_user),
	.mprj_stb_o_user(mprj_stb_o_user),
	.mprj_we_o_user(mprj_we_o_user),
	.mprj_sel_o_user(mprj_sel_o_user),
	.mprj_adr_o_user(mprj_adr_o_user),
	.mprj_dat_o_user(mprj_dat_o_user),
	.mprj_dat_i_user(mprj_dat_i_user),
	.mprj_ack_i_user(mprj_ack_i_user),
	.user_irq(user_irq),
	.user1_vcc_powergood(mprj_vcc_pwrgood),
	.user2_vcc_powergood(mprj2_vcc_pwrgood),
	.user1_vdd_powergood(mprj_vdd_pwrgood),
	.user2_vdd_powergood(mprj2_vdd_pwrgood)
    );


    /*--------------------------------------------------*/
    /* Wrapper module around the user project 		*/
    /*--------------------------------------------------*/

    assign user_io_in_3v3 = mprj_io_in_3v3;
	
    user_analog_project_wrapper mprj ( 
	`ifdef USE_POWER_PINS
	     .vdda1(vdda1_core),	// User area 1 3.3V power
	     .vdda2(vdda2_core),	// User area 2 3.3V power
	     .vssa1(vssa1_core),	// User area 1 analog ground
	     .vssa2(vssa2_core),	// User area 2 analog ground
	     .vccd1(vccd1_core),	// User area 1 1.8V power
	     .vccd2(vccd2_core),	// User area 2 1.8V power
	     .vssd1(vssd1_core),	// User area 1 digital ground
	     .vssd2(vssd2_core),	// User area 2 digital ground
	`endif

    	.wb_clk_i(mprj_clock),
    	.wb_rst_i(mprj_reset),

	// MGMT SoC Wishbone Slave
	.wbs_cyc_i(mprj_cyc_o_user),
	.wbs_stb_i(mprj_stb_o_user),
	.wbs_we_i(mprj_we_o_user),
	.wbs_sel_i(mprj_sel_o_user),
	.wbs_adr_i(mprj_adr_o_user),
	.wbs_dat_i(mprj_dat_o_user),
	.wbs_ack_o(mprj_ack_i_user),
	.wbs_dat_o(mprj_dat_i_user),

	// GPIO pad 3-pin interface (plus analog)
	.io_in (user_io_in),
	.io_in_3v3 (user_io_in_3v3),
    	.io_out(user_io_out),
    	.io_oeb(user_io_oeb),
	.io_analog(user_analog),
	.gpio_analog(user_gpio_analog),
	.gpio_noesd(user_gpio_noesd),

	// Logic Analyzer
	.la_data_in(la_data_in_user),
	.la_data_out(la_data_out_user),
	.la_oenb(la_oenb_user),

	// User-accessible power supply clamps
	.io_clamp_high(user_clamp_high),
	.io_clamp_low(user_clamp_low),

	// Independent clock
	.user_clock2(mprj_clock2),

	// IRQ
	.user_irq(user_irq_core)
    );

    /*--------------------------------------*/
    /* End user project instantiation	*/
    /*--------------------------------------*/

    wire [`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1:0] gpio_serial_link_1_shifted;
    wire [`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1:0] gpio_serial_link_2_shifted;

    assign gpio_serial_link_1_shifted = {gpio_serial_link_1[`MPRJ_IO_PADS_1
					-`ANALOG_PADS_1-2:0],
					 mprj_io_loader_data_1};
    // Note that serial_link_2 is backwards compared to serial_link_1, so it
    // shifts in the other direction.
    assign gpio_serial_link_2_shifted = {mprj_io_loader_data_2,
					 gpio_serial_link_2[`MPRJ_IO_PADS_2
					-`ANALOG_PADS_2-1:1]};

    // Propagating clock and reset to mitigate timing and fanout issues
    wire [`MPRJ_IO_PADS_1-1:0] gpio_clock_1;
    wire [`MPRJ_IO_PADS_2-1:0] gpio_clock_2;
    wire [`MPRJ_IO_PADS_1-1:0] gpio_resetn_1;
    wire [`MPRJ_IO_PADS_2-1:0] gpio_resetn_2;
    wire [`MPRJ_IO_PADS_1-1:0] gpio_load_1;
    wire [`MPRJ_IO_PADS_2-1:0] gpio_load_2;
    wire [`MPRJ_IO_PADS_1-6:0] gpio_clock_1_shifted;
    wire [`MPRJ_IO_PADS_2-7:0] gpio_clock_2_shifted;
    wire [`MPRJ_IO_PADS_1-6:0] gpio_resetn_1_shifted;
    wire [`MPRJ_IO_PADS_2-7:0] gpio_resetn_2_shifted;
    wire [`MPRJ_IO_PADS_1-6:0] gpio_load_1_shifted;
    wire [`MPRJ_IO_PADS_2-7:0] gpio_load_2_shifted;

    assign gpio_clock_1_shifted = {gpio_clock_1[`MPRJ_IO_PADS_1-`ANALOG_PADS_1-2:0],
				mprj_io_loader_clock};
    assign gpio_clock_2_shifted = {mprj_io_loader_clock,
				gpio_clock_2[`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1:1]};
    assign gpio_resetn_1_shifted = {gpio_resetn_1[`MPRJ_IO_PADS_1-`ANALOG_PADS_1-2:0],
				mprj_io_loader_resetn};
    assign gpio_resetn_2_shifted = {mprj_io_loader_resetn,
				gpio_resetn_2[`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1:1]};
    assign gpio_load_1_shifted = {gpio_load_1[`MPRJ_IO_PADS_1-`ANALOG_PADS_1-2:0],
				mprj_io_loader_strobe};
    assign gpio_load_2_shifted = {mprj_io_loader_strobe,
				gpio_load_2[`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1:1]};

    wire [2:0] spi_pll_sel;
    wire [2:0] spi_pll90_sel;
    wire [4:0] spi_pll_div;
    wire [25:0] spi_pll_trim;

    // Clocking control

    caravel_clocking clocking(
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif
	.ext_clk_sel(ext_clk_sel),
	.ext_clk(clock_core),
	.pll_clk(pll_clk),
	.pll_clk90(pll_clk90),
	.resetb(rstb_l),
	.sel(spi_pll_sel),
	.sel2(spi_pll90_sel),
	.ext_reset(ext_reset),  // From housekeeping SPI
	.core_clk(caravel_clk),
	.user_clk(caravel_clk2),
	.resetb_sync(caravel_rstn)
    );

    // DCO/Digital Locked Loop

    digital_pll pll (
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif
	.resetb(rstb_l),
	.enable(spi_pll_ena),
	.osc(clock_core),
	.clockp({pll_clk, pll_clk90}),
	.div(spi_pll_div),
	.dco(spi_pll_dco_ena),
	.ext_trim(spi_pll_trim)
    );

    // Housekeeping interface

    housekeeping housekeeping (
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif

	.wb_clk_i(caravel_clk),
	.wb_rstn_i(caravel_rstn),

	.wb_adr_i(mprj_adr_o_core),
	.wb_dat_i(mprj_dat_o_core),
	.wb_sel_i(mprj_sel_o_core),
	.wb_we_i(mprj_we_o_core),
	.wb_cyc_i(hk_cyc_o),
	.wb_stb_i(hk_stb_o),
	.wb_ack_o(hk_ack_i),
	.wb_dat_o(hk_dat_i),

	.porb(porb_l),

	.pll_ena(spi_pll_ena),
	.pll_dco_ena(spi_pll_dco_ena),
	.pll_div(spi_pll_div),
	.pll_sel(spi_pll_sel),
	.pll90_sel(spi_pll90_sel),
	.pll_trim(spi_pll_trim),
	.pll_bypass(ext_clk_sel),

	.qspi_enabled(qspi_enabled),
	.uart_enabled(uart_enabled),
	.spi_enabled(spi_enabled),
	.debug_mode(debug_mode),

	.ser_tx(ser_tx),
	.ser_rx(ser_rx),

	.spi_sdi(spi_sdi),
	.spi_csb(spi_csb),
	.spi_sck(spi_sck),
	.spi_sdo(spi_sdo),
	.spi_sdoenb(spi_sdoenb),

	.debug_in(debug_in),
	.debug_out(debug_out),
	.debug_oeb(debug_oeb),

	.irq(irq_spi),
	.reset(ext_reset),

	.serial_clock(mprj_io_loader_clock),
	.serial_load(mprj_io_loader_strobe),
	.serial_resetn(mprj_io_loader_resetn),
	.serial_data_1(mprj_io_loader_data_1),
	.serial_data_2(mprj_io_loader_data_2),

	.mgmt_gpio_in(mgmt_io_in),
	.mgmt_gpio_out({mgmt_io_out[4:2], mgmt_io_in[`MPRJ_IO_PADS-4:2],
			mgmt_io_out[1:0]}),
	.mgmt_gpio_oeb({mgmt_io_oeb[4:2], mgmt_io_nc[`MPRJ_IO_PADS-6:0],
			mgmt_io_oeb[1:0]}),

	.pwr_ctrl_out(pwr_ctrl_nc),        /* Not used in this version */

	.trap(trap),

	.user_clock(caravel_clk2),

	.mask_rev_in(mask_rev),

	.spimemio_flash_csb(flash_csb_core),
	.spimemio_flash_clk(flash_clk_core),
	.spimemio_flash_io0_oeb(flash_io0_oeb_core),
	.spimemio_flash_io1_oeb(flash_io1_oeb_core),
	.spimemio_flash_io2_oeb(flash_io2_oeb_core),
	.spimemio_flash_io3_oeb(flash_io3_oeb_core),
	.spimemio_flash_io0_do(flash_io0_do_core),
	.spimemio_flash_io1_do(flash_io1_do_core),
	.spimemio_flash_io2_do(flash_io2_do_core),
	.spimemio_flash_io3_do(flash_io3_do_core),
	.spimemio_flash_io0_di(flash_io0_di_core),
	.spimemio_flash_io1_di(flash_io1_di_core),
	.spimemio_flash_io2_di(flash_io2_di_core),
	.spimemio_flash_io3_di(flash_io3_di_core),

	.pad_flash_csb(flash_csb_frame),
	.pad_flash_csb_oeb(flash_csb_oeb),
	.pad_flash_clk(flash_clk_frame),
	.pad_flash_clk_oeb(flash_clk_oeb),
	.pad_flash_io0_oeb(flash_io0_oeb),
	.pad_flash_io1_oeb(flash_io1_oeb),
	.pad_flash_io0_ieb(flash_io0_ieb),
	.pad_flash_io1_ieb(flash_io1_ieb),
	.pad_flash_io0_do(flash_io0_do),
	.pad_flash_io1_do(flash_io1_do),
	.pad_flash_io0_di(flash_io0_di),
	.pad_flash_io1_di(flash_io1_di),

	.sram_ro_clk(hkspi_sram_clk),
	.sram_ro_csb(hkspi_sram_csb),
	.sram_ro_addr(hkspi_sram_addr),
	.sram_ro_data(hkspi_sram_data),

	.usr1_vcc_pwrgood(mprj_vcc_pwrgood),
	.usr2_vcc_pwrgood(mprj2_vcc_pwrgood),
	.usr1_vdd_pwrgood(mprj_vdd_pwrgood),
	.usr2_vdd_pwrgood(mprj2_vdd_pwrgood)
    );

    /* GPIO defaults (via programmed) */
    wire [(`MPRJ_IO_PADS - `ANALOG_PADS)*13-1:0] gpio_defaults;

    /* Fixed defaults for the first 5 GPIO pins */

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(13'h1803)
    ) gpio_defaults_block_0 [1:0] (
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif
	.gpio_defaults(gpio_defaults[25:0])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(13'h0403)
    ) gpio_defaults_block_2 [2:0] (
	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
	`endif
	.gpio_defaults(gpio_defaults[64:26])
    );

    /* Via-programmable defaults for the rest of the GPIO pins */

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_5_INIT)
    ) gpio_defaults_block_5 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[77:65])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_6_INIT)
    ) gpio_defaults_block_6 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[90:78])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_7_INIT)
    ) gpio_defaults_block_7 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[103:91])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_8_INIT)
    ) gpio_defaults_block_8 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[116:104])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_9_INIT)
    ) gpio_defaults_block_9 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[129:117])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_10_INIT)
    ) gpio_defaults_block_10 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[142:130])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_11_INIT)
    ) gpio_defaults_block_11 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[155:143])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_12_INIT)
    ) gpio_defaults_block_12 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[168:156])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_13_INIT)
    ) gpio_defaults_block_13 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[181:169])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_14_INIT)
    ) gpio_defaults_block_14 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[194:182])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_26_INIT)
    ) gpio_defaults_block_26 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[207:195])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_27_INIT)
    ) gpio_defaults_block_27 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[220:208])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_28_INIT)
    ) gpio_defaults_block_28 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[233:221])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_29_INIT)
    ) gpio_defaults_block_29 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[246:234])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_30_INIT)
    ) gpio_defaults_block_30 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[259:247])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_31_INIT)
    ) gpio_defaults_block_31 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[272:260])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_32_INIT)
    ) gpio_defaults_block_32 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[285:273])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_33_INIT)
    ) gpio_defaults_block_33 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[298:286])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_34_INIT)
    ) gpio_defaults_block_34 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[311:299])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_35_INIT)
    ) gpio_defaults_block_35 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[324:312])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_36_INIT)
    ) gpio_defaults_block_36 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[337:325])
    );

    gpio_defaults_block #(
	.GPIO_CONFIG_INIT(`USER_CONFIG_GPIO_37_INIT)
    ) gpio_defaults_block_37 (
    	`ifdef USE_POWER_PINS
	    .VPWR(vccd_core),
	    .VGND(vssd_core),
        `endif
	.gpio_defaults(gpio_defaults[350:338])
    );

    // Each control block sits next to an I/O pad in the user area.
    // It gets input through a serial chain from the previous control
    // block and passes it to the next control block.  Due to the nature
    // of the shift register, bits are presented in reverse, as the first
    // bit in ends up as the last bit of the last I/O pad control block.

    // There are two types of block;  the first two and the last two
    // are configured to be full bidirectional under control of the
    // management Soc (JTAG and SDO for the first two;  flash_io2 and
    // flash_io3 for the last two).  The rest are configured to be default
    // (input).  Note that the first two and last two are the ones closest
    // to the management SoC on either side, which minimizes the wire length
    // of the extra signals those pads need.

    /* First two GPIOs (JTAG and SDO) */
    gpio_control_block gpio_control_bidir_1 [1:0] (
   	`ifdef USE_POWER_PINS
	    .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
	`endif

	.gpio_defaults(gpio_defaults[25:0]),

    	// Management Soc-facing signals

	.resetn(gpio_resetn_1_shifted[1:0]),
	.serial_clock(gpio_clock_1_shifted[1:0]),
	.serial_load(gpio_load_1_shifted[1:0]),

	.resetn_out(gpio_resetn_1[1:0]),
	.serial_clock_out(gpio_clock_1[1:0]),
	.serial_load_out(gpio_load_1[1:0]),

    	.mgmt_gpio_in(mgmt_io_in[1:0]),
	.mgmt_gpio_out({sdo_out, jtag_out}),
	.mgmt_gpio_oeb({sdo_outenb, jtag_outenb}),

        .one(),
        .zero(),

    	// Serial data chain for pad configuration
    	.serial_data_in(gpio_serial_link_1_shifted[1:0]),
    	.serial_data_out(gpio_serial_link_1[1:0]),

    	// User-facing signals
    	.user_gpio_out(user_io_out[1:0]),
    	.user_gpio_oeb(user_io_oeb[1:0]),
    	.user_gpio_in(user_io_in[1:0]),

    	// Pad-facing signals (Pad GPIOv2)
    	.pad_gpio_inenb(mprj_io_inp_dis[1:0]),
    	.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[1:0]),
    	.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[1:0]),
    	.pad_gpio_slow_sel(mprj_io_slow_sel[1:0]),
    	.pad_gpio_holdover(mprj_io_holdover[1:0]),
    	.pad_gpio_ana_en(mprj_io_analog_en[1:0]),
    	.pad_gpio_ana_sel(mprj_io_analog_sel[1:0]),
    	.pad_gpio_ana_pol(mprj_io_analog_pol[1:0]),
    	.pad_gpio_dm(mprj_io_dm[5:0]),
    	.pad_gpio_outenb(mprj_io_oeb[1:0]),
    	.pad_gpio_out(mprj_io_out[1:0]),
    	.pad_gpio_in(mprj_io_in[1:0])
    );

    /* Section 1 GPIOs (GPIO 0 to 18) */
    wire [`MPRJ_IO_PADS_1-`ANALOG_PADS_1-3:0] one_loop1;

    /* Section 1 GPIOs (GPIO 2 to 7) that start up under management control */

    gpio_control_block gpio_control_in_1a [5:0] (
	`ifdef USE_POWER_PINS
            .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
	`endif

	.gpio_defaults(gpio_defaults[103:26]),

    	// Management Soc-facing signals

	.resetn(gpio_resetn_1_shifted[7:2]),
	.serial_clock(gpio_clock_1_shifted[7:2]),
	.serial_load(gpio_load_1_shifted[7:2]),

	.resetn_out(gpio_resetn_1[7:2]),
	.serial_clock_out(gpio_clock_1[7:2]),
	.serial_load_out(gpio_load_1[7:2]),

	.mgmt_gpio_in(mgmt_io_in[7:2]),
	.mgmt_gpio_out(mgmt_io_in[7:2]),
	.mgmt_gpio_oeb(one_loop1[5:0]),

        .one(one_loop1[5:0]),
        .zero(),

    	// Serial data chain for pad configuration
    	.serial_data_in(gpio_serial_link_1_shifted[7:2]),
    	.serial_data_out(gpio_serial_link_1[7:2]),

    	// User-facing signals
    	.user_gpio_out(user_io_out[7:2]),
    	.user_gpio_oeb(user_io_oeb[7:2]),
    	.user_gpio_in(user_io_in[7:2]),

    	// Pad-facing signals (Pad GPIOv2)
    	.pad_gpio_inenb(mprj_io_inp_dis[7:2]),
    	.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[7:2]),
    	.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[7:2]),
    	.pad_gpio_slow_sel(mprj_io_slow_sel[7:2]),
    	.pad_gpio_holdover(mprj_io_holdover[7:2]),
    	.pad_gpio_ana_en(mprj_io_analog_en[7:2]),
    	.pad_gpio_ana_sel(mprj_io_analog_sel[7:2]),
    	.pad_gpio_ana_pol(mprj_io_analog_pol[7:2]),
    	.pad_gpio_dm(mprj_io_dm[23:6]),
    	.pad_gpio_outenb(mprj_io_oeb[7:2]),
    	.pad_gpio_out(mprj_io_out[7:2]),
    	.pad_gpio_in(mprj_io_in[7:2])
    );

    /* Section 1 GPIOs (GPIO 8 to 18) */
    gpio_control_block gpio_control_in_1 [`MPRJ_IO_PADS_1-`ANALOG_PADS_1-9:0] (
	`ifdef USE_POWER_PINS
            .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
	`endif

	.gpio_defaults(gpio_defaults[((`MPRJ_IO_PADS_1-`ANALOG_PADS_1)*13-1):104]),

    	// Management Soc-facing signals

	.resetn(gpio_resetn_1_shifted[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
	.serial_clock(gpio_clock_1_shifted[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
	.serial_load(gpio_load_1_shifted[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),

	.resetn_out(gpio_resetn_1[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
	.serial_clock_out(gpio_clock_1[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
	.serial_load_out(gpio_load_1[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),

	.mgmt_gpio_in(mgmt_io_in[`DIG1_TOP:8]),
	.mgmt_gpio_out(mgmt_io_in[`DIG1_TOP:8]),
	.mgmt_gpio_oeb(one_loop1[`MPRJ_IO_PADS_1-`ANALOG_PADS_1-3:6]),

        .one(one_loop1[`MPRJ_IO_PADS_1-`ANALOG_PADS_1-3:6]),
        .zero(),

    	// Serial data chain for pad configuration
    	.serial_data_in(gpio_serial_link_1_shifted[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.serial_data_out(gpio_serial_link_1[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),

    	// User-facing signals
    	.user_gpio_out(user_io_out[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.user_gpio_oeb(user_io_oeb[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.user_gpio_in(user_io_in[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),

    	// Pad-facing signals (Pad GPIOv2)
    	.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_dm(mprj_io_dm[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)*3-1:24]),
    	.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_out(mprj_io_out[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8]),
    	.pad_gpio_in(mprj_io_in[(`MPRJ_IO_PADS_1-`ANALOG_PADS_1-1):8])
    );

    /* Last three GPIOs (spi_sdo, flash_io2 and flash_io3) */

    gpio_control_block gpio_control_bidir_2 [2:0] (
    	`ifdef USE_POWER_PINS
	    .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
        `endif

	.gpio_defaults(gpio_defaults[((`MPRJ_IO_PADS-`ANALOG_PADS)*13-1):((`MPRJ_IO_PADS-`ANALOG_PADS)*13-39)]),

    	// Management Soc-facing signals

	.resetn(gpio_resetn_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),
	.serial_clock(gpio_clock_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),
	.serial_load(gpio_load_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),

	.resetn_out(gpio_resetn_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),
	.serial_clock_out(gpio_clock_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),
	.serial_load_out(gpio_load_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),

	.mgmt_gpio_in(mgmt_io_in[(`DIG2_TOP):(`DIG2_TOP-2)]),
	.mgmt_gpio_out(mgmt_io_out[4:2]),
	.mgmt_gpio_oeb(mgmt_io_oeb[4:2]),

        .one(),
        .zero(),

    	// Serial data chain for pad configuration
    	.serial_data_in(gpio_serial_link_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),
    	.serial_data_out(gpio_serial_link_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-1):(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-3)]),

    	// User-facing signals
    	.user_gpio_out(user_io_out[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.user_gpio_oeb(user_io_oeb[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.user_gpio_in(user_io_in[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),

    	// Pad-facing signals (Pad GPIOv2)
    	.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_dm(mprj_io_dm[(`MPRJ_DIG_PADS*3-1):(`MPRJ_DIG_PADS*3-9)]),
    	.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_out(mprj_io_out[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)]),
    	.pad_gpio_in(mprj_io_in[(`MPRJ_DIG_PADS-1):(`MPRJ_DIG_PADS-3)])
    );

    /* Section 2 GPIOs (GPIO 19 to 37) */
    wire [`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4:0] one_loop2;

    gpio_control_block gpio_control_in_2 [`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4:0] (
	`ifdef USE_POWER_PINS
            .vccd(vccd_core),
	    .vssd(vssd_core),
	    .vccd1(vccd1_core),
	    .vssd1(vssd1_core),
	`endif

 	.gpio_defaults(gpio_defaults[((`MPRJ_IO_PADS-`ANALOG_PADS-3)*13-1):((`MPRJ_IO_PADS_1-`ANALOG_PADS_1)*13)]),

    	// Management Soc-facing signals

	.resetn(gpio_resetn_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),
	.serial_clock(gpio_clock_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),
	.serial_load(gpio_load_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),

	.resetn_out(gpio_resetn_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),
	.serial_clock_out(gpio_clock_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),
	.serial_load_out(gpio_load_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),

 	.mgmt_gpio_in(mgmt_io_in[(`DIG2_TOP-3):`DIG2_BOT]),
 	.mgmt_gpio_out(mgmt_io_in[(`DIG2_TOP-3):`DIG2_BOT]),
	.mgmt_gpio_oeb(one_loop2),

        .one(one_loop2),
        .zero(),

    	// Serial data chain for pad configuration
    	.serial_data_in(gpio_serial_link_2_shifted[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),
    	.serial_data_out(gpio_serial_link_2[(`MPRJ_IO_PADS_2-`ANALOG_PADS_2-4):0]),

    	// User-facing signals
   	.user_gpio_out(user_io_out[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
   	.user_gpio_oeb(user_io_oeb[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
  	.user_gpio_in(user_io_in[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),

    	// Pad-facing signals (Pad GPIOv2)
    	.pad_gpio_inenb(mprj_io_inp_dis[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_ib_mode_sel(mprj_io_ib_mode_sel[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_vtrip_sel(mprj_io_vtrip_sel[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_slow_sel(mprj_io_slow_sel[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_holdover(mprj_io_holdover[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_ana_en(mprj_io_analog_en[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_ana_sel(mprj_io_analog_sel[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_ana_pol(mprj_io_analog_pol[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_dm(mprj_io_dm[((`MPRJ_DIG_PADS)*3-10):((`MPRJ_IO_PADS_1-`ANALOG_PADS_1)*3)]),
    	.pad_gpio_outenb(mprj_io_oeb[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_out(mprj_io_out[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)]),
    	.pad_gpio_in(mprj_io_in[(`MPRJ_DIG_PADS-4):(`MPRJ_IO_PADS_1-`ANALOG_PADS_1)])
    );

    user_id_programming #(
	.USER_PROJECT_ID(USER_PROJECT_ID)
    ) user_id_value (
	`ifdef USE_POWER_PINS
		.VPWR(vccd_core),
		.VGND(vssd_core),
	`endif
	.mask_rev(mask_rev)
    );

    // Power-on-reset circuit
    simple_por por (
	`ifdef USE_POWER_PINS
		.vdd3v3(vddio_core),
		.vdd1v8(vccd_core),
		.vss3v3(vssio_core),
		.vss1v8(vssd_core),
	`endif
		.porb_h(porb_h),
		.porb_l(porb_l),
		.por_l(por_l)
    );

    // XRES (chip input pin reset) reset level converter
    xres_buf rstb_level (
	`ifdef USE_POWER_PINS
		.VPWR(vddio_core),
		.LVPWR(vccd_core),
		.LVGND(vssd_core),
		.VGND(vssio_core),
	`endif
		.A(rstb_h),
		.X(rstb_l)
    );

    // Spare logic for metal mask fixes
    wire [107:0] spare_xz_nc;
    wire [15:0] spare_xi_nc;
    wire [3:0] spare_xib_nc;
    wire [7:0] spare_xna_nc;
    wire [7:0] spare_xno_nc;
    wire [7:0] spare_xmx_nc;
    wire [7:0] spare_xfq_nc;
    wire [7:0] spare_xfqn_nc;

    spare_logic_block spare_logic [3:0] (
	`ifdef USE_POWER_PINS
		.vccd(vccd_core),
		.vssd(vssd_core),
	`endif
		.spare_xz(spare_xz_nc),
		.spare_xi(spare_xi_nc),
		.spare_xib(spare_xib_nc),
		.spare_xna(spare_xna_nc),
		.spare_xno(spare_xno_nc),
		.spare_xmx(spare_xmx_nc),
		.spare_xfq(spare_xfq_nc),
		.spare_xfqn(spare_xfqn_nc)
    );

endmodule
// `default_nettype wire