/*
 * SPDX-FileCopyrightText: 2020 Efabless Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 * SPDX-License-Identifier: Apache-2.0
 */

#include "../../defs.h"

// --------------------------------------------------------

/*
 *	SPI master Test
 *	- Enables SPI master
 *	- Uses SPI master to talk to external SPI module
 */
void main()
{
    int i;
    uint32_t value;

    reg_mprj_datal = 0;

    // For SPI operation, GPIO 1 should be an input, and GPIOs 2 to 4
    // should be outputs.

    reg_mprj_io_34  = GPIO_MODE_MGMT_STD_INPUT_NOPULL;	// SDI
    reg_mprj_io_35  = GPIO_MODE_MGMT_STD_BIDIRECTIONAL;	// SDO
    reg_mprj_io_33  = GPIO_MODE_MGMT_STD_OUTPUT;	// CSB
    reg_mprj_io_32  = GPIO_MODE_MGMT_STD_OUTPUT;	// SCK
    
    // Configure upper 16 bits of user GPIO for generating testbench
    // checkpoints.

    reg_mprj_io_31 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_30 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_29 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_28 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_27 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_26 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_25 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_24 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_23 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_22 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_21 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_20 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_19 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_18 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_17 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_16 = GPIO_MODE_MGMT_STD_OUTPUT;

    // Configure next 8 bits for writing the SPI value read on GPIO
    reg_mprj_io_15 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_14 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_13 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_12 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_11 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_10 = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_9  = GPIO_MODE_MGMT_STD_OUTPUT;
    reg_mprj_io_8  = GPIO_MODE_MGMT_STD_OUTPUT;


    /* Apply configuration */
    reg_mprj_xfer = 1;
    while (reg_mprj_xfer == 1);

    // Start test
    reg_mprj_datal = 0xA0400000;

    // Enable SPI master
    // SPI master configuration bits:
    // bits 7-0:	Clock prescaler value (default 2)
    // bit  8:		MSB/LSB first (0 = MSB first, 1 = LSB first)
    // bit  9:		CSB sense (0 = inverted, 1 = noninverted)
    // bit 10:		SCK sense (0 = noninverted, 1 = inverted)
    // bit 11:		mode (0 = read/write opposite edges, 1 = same edges)
    // bit 12:		stream (1 = CSB ends transmission)
    // bit 13:		enable (1 = enabled)
    // bit 14:		IRQ enable (1 = enabled)
    // bit 15:		(unused)

    reg_spimaster_config = 0x2002;	// Enable, prescaler = 2,

    // Apply stream read (0x40 + 0x03) and read back one byte 

    reg_spimaster_config = 0x3002;	// Apply stream mode

    reg_spimaster_data = 0xff;		// Write 0xff (reset)
    reg_spimaster_config = 0x2102;	// Release CSB (ends stream mode)
    reg_spimaster_config = 0x3002;	// Apply stream mode
    reg_spimaster_data = 0xab;		// Write 0xab (wakeup)
    reg_spimaster_config = 0x2102;	// Release CSB (ends stream mode)
    reg_spimaster_config = 0x3002;	// Apply stream mode
    reg_spimaster_data = 0x03;		// Write 0x03 (read mode)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address high byte)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address middle byte)
    reg_spimaster_data = 0x04;		// Write 0x00 (start address low byte)

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0410000 | (value << 8);	// 0x93

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0420000 | (value << 8);	// 0x01

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0430000 | (value << 8);	// 0x00

    reg_spimaster_config = 0x2102;	// Release CSB (ends stream mode)
    reg_spimaster_config = 0x3002;	// Apply stream mode
    reg_spimaster_data = 0x03;		// Write 0x03 (read mode)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address low byte)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address middle byte)
    reg_spimaster_data = 0x08;		// Write 0x08 (start address high byte)

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0440000 | (value << 8);	// 0x13

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0450000 | (value << 8);	// 0x02

    reg_spimaster_config = 0x2102;	// Release CSB (ends stream mode)
    reg_spimaster_config = 0x3002;	// Apply stream mode
    reg_spimaster_data = 0x03;		// Write 0x03 (read mode)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address high byte)
    reg_spimaster_data = 0x00;		// Write 0x00 (start address middle byte)
    reg_spimaster_data = 0xa0;		// Write 0xa0 (start address low byte)

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0460000 | (value << 8);	// 0x63

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0470000 | (value << 8);	// 0x57

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0480000 | (value << 8);	// 0xb5

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA0490000 | (value << 8);	// 0x00

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA04a0000 | (value << 8);	// 0x23

    reg_spimaster_data = 0x00;		// Write 0x00 for read
    value = reg_spimaster_data;		// Read back byte
    // Write checkpoint
    reg_mprj_datal = 0xA04b0000 | (value << 8);	// 0x20

    reg_spimaster_config = 0x2102;	// Release CSB (ends stream mode)
    reg_spimaster_config = 0x0002;	// Disable the SPI master

    // End test
    reg_mprj_datal = 0xA0900000;
}