| // SPDX-FileCopyrightText: 2020 Efabless Corporation | |
| // | |
| // Licensed under the Apache License, Version 2.0 (the "License"); | |
| // you may not use this file except in compliance with the License. | |
| // You may obtain a copy of the License at | |
| // | |
| // http://www.apache.org/licenses/LICENSE-2.0 | |
| // | |
| // Unless required by applicable law or agreed to in writing, software | |
| // distributed under the License is distributed on an "AS IS" BASIS, | |
| // WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. | |
| // See the License for the specific language governing permissions and | |
| // limitations under the License. | |
| // SPDX-License-Identifier: Apache-2.0 | |
| `default_nettype wire | |
| `timescale 1 ns / 1 ps | |
| `include "uprj_netlists.v" | |
| `include "caravel_netlists.v" | |
| `include "spiflash.v" | |
| `include "tbuart.v" | |
| module mprj_stimulus_tb; | |
| // Signals declaration | |
| reg clock; | |
| reg RSTB; | |
| reg CSB; | |
| reg power1, power2; | |
| reg power3, power4; | |
| wire HIGH; | |
| wire LOW; | |
| wire TRI; | |
| assign HIGH = 1'b1; | |
| assign LOW = 1'b0; | |
| assign TRI = 1'bz; | |
| wire gpio; | |
| wire uart_tx; | |
| wire [37:0] mprj_io; | |
| wire [15:0] checkbits; | |
| wire [3:0] status; | |
| // Signals Assignment | |
| assign checkbits = mprj_io[31:16]; | |
| assign status = mprj_io[35:32]; | |
| assign uart_tx = mprj_io[6]; | |
| assign mprj_io[3] = (CSB == 1'b1) ? 1'b1 : 1'bz; | |
| always #12.5 clock <= (clock === 1'b0); | |
| initial begin | |
| clock = 0; | |
| end | |
| initial begin | |
| $dumpfile("mprj_stimulus.vcd"); | |
| $dumpvars(0, mprj_stimulus_tb); | |
| // Repeat cycles of 1000 clock edges as needed to complete testbench | |
| repeat (150) begin | |
| repeat (1000) @(posedge clock); | |
| end | |
| $display("%c[1;31m",27); | |
| $display ("Monitor: Timeout, Test Project IO Stimulus (RTL) Failed"); | |
| $display("%c[0m",27); | |
| $finish; | |
| end | |
| initial begin | |
| wait(checkbits == 16'hAB40); | |
| $display("Monitor: mprj_stimulus test started"); | |
| wait(status == 4'ha); | |
| wait(status == 4'h5); | |
| // Value 0009 reflects copying user-controlled outputs to memory and back | |
| // to management-controlled outputs. | |
| wait(checkbits == 16'h0009); | |
| wait(checkbits == 16'hAB51); | |
| $display("Monitor: mprj_stimulus test Passed"); | |
| #10000; | |
| $finish; | |
| end | |
| // Reset Operation | |
| initial begin | |
| RSTB <= 1'b0; | |
| CSB <= 1'b1; // Force CSB high | |
| #2000; | |
| RSTB <= 1'b1; // Release reset | |
| #170000; | |
| CSB = 1'b0; // CSB can be released | |
| end | |
| initial begin // Power-up sequence | |
| power1 <= 1'b0; | |
| power2 <= 1'b0; | |
| #200; | |
| power1 <= 1'b1; | |
| #200; | |
| power2 <= 1'b1; | |
| end | |
| wire flash_csb; | |
| wire flash_clk; | |
| wire flash_io0; | |
| wire flash_io1; | |
| wire VDD3V3 = power1; | |
| wire VDD1V8 = power2; | |
| wire VSS = 1'b0; | |
| caravel uut ( | |
| .vddio (VDD3V3), | |
| .vssio (VSS), | |
| .vdda (VDD3V3), | |
| .vssa (VSS), | |
| .vccd (VDD1V8), | |
| .vssd (VSS), | |
| .vdda1 (VDD3V3), | |
| .vdda2 (VDD3V3), | |
| .vssa1 (VSS), | |
| .vssa2 (VSS), | |
| .vccd1 (VDD1V8), | |
| .vccd2 (VDD1V8), | |
| .vssd1 (VSS), | |
| .vssd2 (VSS), | |
| .clock (clock), | |
| .gpio (gpio), | |
| .mprj_io (mprj_io), | |
| .flash_csb(flash_csb), | |
| .flash_clk(flash_clk), | |
| .flash_io0(flash_io0), | |
| .flash_io1(flash_io1), | |
| .resetb (RSTB) | |
| ); | |
| spiflash #( | |
| .FILENAME("mprj_stimulus.hex") | |
| ) spiflash ( | |
| .csb(flash_csb), | |
| .clk(flash_clk), | |
| .io0(flash_io0), | |
| .io1(flash_io1), | |
| .io2(), // not used | |
| .io3() // not used | |
| ); | |
| // Testbench UART | |
| tbuart tbuart ( | |
| .ser_rx(uart_tx) | |
| ); | |
| endmodule | |
| `default_nettype wire |