// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *-------------------------------------------------------------
 *
 * user_proj_example
 *
 * This is an example of a (trivially simple) user project,
 * showing how the user project can connect to the logic
 * analyzer, the wishbone bus, and the I/O pads.
 *
 * This project generates an integer count, which is output
 * on the user area GPIO pads (digital output only).  The
 * wishbone connection allows the project to be controlled
 * (start and stop) from the management SoC program.
 *
 * See the testbenches in directory "mprj_counter" for the
 * example programs that drive this user project.  The three
 * testbenches are "io_ports", "la_test1", and "la_test2".
 *
 *-------------------------------------------------------------
 */

module user_proj_example #(
    parameter BITS = 32
)(
`ifdef USE_POWER_PINS
    inout vccd1,	// User area 1 1.8V supply
    inout vssd1,	// User area 1 digital ground
`endif

    // Wishbone Slave ports (WB MI A)
    input wb_clk_i,
    input wb_rst_i,
    input wbs_stb_i,
    input wbs_cyc_i,
    input wbs_we_i,
    input [3:0] wbs_sel_i,
    input [31:0] wbs_dat_i,
    input [31:0] wbs_adr_i,
    output wbs_ack_o,
    output [31:0] wbs_dat_o,

    // Logic Analyzer Signals
    input  [127:0] la_data_in,
    output [127:0] la_data_out,
    input  [127:0] la_oenb,

    // IOs
    input  [`MPRJ_IO_PADS-1:0] io_in,
    output [`MPRJ_IO_PADS-1:0] io_out,
    output [`MPRJ_IO_PADS-1:0] io_oeb,

    // IRQ
    output [2:0] irq
);
    wire clk;
    wire rst;

    wire [`MPRJ_IO_PADS-1:0] io_in;
    wire [`MPRJ_IO_PADS-1:0] io_out;
    wire [`MPRJ_IO_PADS-1:0] io_oeb;

    wire [31:0] rdata; 
    wire [31:0] wdata;
    //wire [BITS-1:0] count;

    wire valid;
    wire [3:0] wstrb;
    wire [31:0] la_write;

    // WB MI A
    assign valid = wbs_cyc_i && wbs_stb_i; 
    assign wstrb = wbs_sel_i & {4{wbs_we_i}};
    assign wbs_dat_o = rdata;
    assign wdata = wbs_dat_i;

    // IO
    //assign io_out = count;
    assign io_oeb = {(`MPRJ_IO_PADS-1){rst}};

    // IRQ
    assign irq = 3'b000;	// Unused

    // LA
    //assign la_data_out = {{(127-BITS){1'b0}}, count};
    // Assuming LA probes [63:32] are for controlling the count register  
    assign la_write = ~la_oenb[63:32] & ~{BITS{valid}};
    // Assuming LA probes [65:64] are for controlling the count clk & reset  
    assign clk = (~la_oenb[64]) ? la_data_in[64]: wb_clk_i;
    assign rst = (~la_oenb[65]) ? la_data_in[65]: wb_rst_i;
	
	
    CLA16 CLA1(.CLK(clk), .RST(RST), .A(io_in[15:0]), .B(io_in[15:0]), .Cin(io_in[16]), .Sum(io_out[32:17]), .Cout(io_out[33]) );
    	

endmodule

module CLA16(input CLK, input RST, input [15:0] A, input [15:0] B, input Cin, output [15:0]Sum, output Cout  );

reg[15:0] tempS;
reg tempC;
assign Sum=tempS;
assign Cout=tempC;

always @(posedge CLK)
    begin
        if (RST)
        begin
            tempC<=0;
            tempS<=16'd0;
        end
        else
        {tempC,tempS}<=A+B+Cin;
    end
endmodule
`default_nettype wire