// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none

`timescale 1 ns / 1 ps

`include "uprj_netlists.v"
`include "caravel_netlists.v"
`include "spiflash.v"

module wb_openram_tb;
	reg clock;
	reg RSTB;
	reg CSB;
	reg power1, power2;
	reg power3, power4;

    wire gpio;
    wire [37:0] mprj_io;
	wire [5:0] checkpoint;
	wire [1:0] status;

	assign checkpoint = mprj_io[31:26];
	assign status = mprj_io[25:24];


	// External clock is used by default.  Make this artificially fast for the
	// simulation.  Normally this would be a slow clock and the digital PLL
	// would be the fast clock.

	always #12.5 clock <= (clock === 1'b0);

	initial begin
		clock = 0;
	end

	initial begin
		$dumpfile("wb_openram.vcd");
		$dumpvars(0, wb_openram_tb);

		// Repeat cycles of 10000 clock edges as needed to complete testbench
		repeat (8) begin
			repeat (10000) @(posedge clock);
			$display("+10000 cycles");
		end
		$display("%c[1;31m",27);
		`ifdef GL
			$display ("Monitor: Timeout, Test OpenRAM Project IO Ports (GL) Failed");
		`else
			$display ("Monitor: Timeout, Test OpenRAM Project IO Ports (RTL) Failed");
		`endif
		$display("%c[0m",27);
		$finish;
	end

	initial begin
		wait(checkpoint == 6'b101010);		// A8
		`ifdef GL
			$display("Monitor: Test OpenRAM Project IO (GL) Started");
		`else
			$display("Monitor: Test OpenRAM Project IO (RTL) Started");
		`endif
		wait(checkpoint == 6'b101011);		// AC, AE, AF
		if (status == 2'b00) begin
			`ifdef GL
				$display("Monitor: Test OpenRAM Project IO (GL) Passed");
			`else
				$display("Monitor: Test OpenRAM Project IO (RTL) Passed");
			`endif
		end
		else begin
			`ifdef GL
				$display("Monitor: Test OpenRAM Project IO (GL) Failed on read operation");
			`else
				$display("Monitor: Test OpenRAM Project IO (RTL) Failed on read operation");
			`endif
		end
	    $finish;
	end

	initial begin
		RSTB <= 1'b0;
		CSB  <= 1'b1;		// Force CSB high
		#2000;
		RSTB <= 1'b1;	    // Release reset
		#1700000;
		CSB = 1'b0;			// CSB can be released
	end

	initial begin		// Power-up sequence
		power1 <= 1'b0;
		power2 <= 1'b0;
		power3 <= 1'b0;
		power4 <= 1'b0;
		#100;
		power1 <= 1'b1;
		#100;
		power2 <= 1'b1;
		#100;
		power3 <= 1'b1;
		#100;
		power4 <= 1'b1;
	end
/*
	always @(mprj_io) begin
		#1 $display("MPRJ-IO state = %b ", mprj_io[20:0]);
	end
*/
	wire flash_csb;
	wire flash_clk;
	wire flash_io0;
	wire flash_io1;

	wire VDD3V3 = power1;
	wire VDD1V8 = power2;
	wire USER_VDD3V3 = power3;
	wire USER_VDD1V8 = power4;
	wire VSS = 1'b0;

	caravel uut (
		.vddio	  (VDD3V3),
		.vssio	  (VSS),
		.vdda	  (VDD3V3),
		.vssa	  (VSS),
		.vccd	  (VDD1V8),
		.vssd	  (VSS),
		.vdda1    (USER_VDD3V3),
		.vdda2    (USER_VDD3V3),
		.vssa1	  (VSS),
		.vssa2	  (VSS),
		.vccd1	  (USER_VDD1V8),
		.vccd2	  (USER_VDD1V8),
		.vssd1	  (VSS),
		.vssd2	  (VSS),
		.clock	  (clock),
		.gpio     (gpio),
        .mprj_io  (mprj_io),
		.flash_csb(flash_csb),
		.flash_clk(flash_clk),
		.flash_io0(flash_io0),
		.flash_io1(flash_io1),
		.resetb	  (RSTB)
	);

	spiflash #(
		.FILENAME("wb_openram.hex")
	) spiflash (
		.csb(flash_csb),
		.clk(flash_clk),
		.io0(flash_io0),
		.io1(flash_io1),
		.io2(),			// not used
		.io3()			// not used
	);

endmodule
`default_nettype wire