// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *-------------------------------------------------------------
 *
 * user_project_wrapper
 *
 * This wrapper enumerates all of the pins available to the
 * user for the user project.
 *
 * An example user project is provided in this wrapper.  The
 * example should be removed and replaced with the actual
 * user project.
 *
 *-------------------------------------------------------------
 */

module user_project_wrapper #(
  parameter BITS = 32
) (
`ifdef USE_POWER_PINS
  inout vdda1,  // User area 1 3.3V supply
  inout vdda2,  // User area 2 3.3V supply
  inout vssa1,  // User area 1 analog ground
  inout vssa2,  // User area 2 analog ground
  inout vccd1,  // User area 1 1.8V supply
  inout vccd2,  // User area 2 1.8v supply
  inout vssd1,  // User area 1 digital ground
  inout vssd2,  // User area 2 digital ground
`endif

  // Wishbone Slave ports (WB MI A)
  input wb_clk_i,
  input wb_rst_i,
  input wbs_stb_i,
  input wbs_cyc_i,
  input wbs_we_i,
  input [3:0] wbs_sel_i,
  input [31:0] wbs_dat_i,
  input [31:0] wbs_adr_i,
  output wbs_ack_o,
  output [31:0] wbs_dat_o,

  // Logic Analyzer Signals
  input  [127:0] la_data_in,
  output [127:0] la_data_out,
  input  [127:0] la_oenb,

  // IOs
  input  [`MPRJ_IO_PADS-1:0] io_in,
  output [`MPRJ_IO_PADS-1:0] io_out,
  output [`MPRJ_IO_PADS-1:0] io_oeb,

  // Analog (direct connection to GPIO pad---use with caution)
  // Note that analog I/O is not available on the 7 lowest-numbered
  // GPIO pads, and so the analog_io indexing is offset from the
  // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
  inout [`MPRJ_IO_PADS-10:0] analog_io,

  // Independent clock (on independent integer divider)
  input   user_clock2,

  // User maskable interrupt signals
  output [2:0] user_irq
);

/*--------------------------------------*/
/* User project is instantiated  here   */
/*--------------------------------------*/

  wire ring0_clk;
  wire ring0_start;
  wire [27:0] ring0_trim_a;
  wire [27:0] ring0_trim_b;
  wire [2:0] ring0_clkmux;

  wire ring1_clk;
  wire ring1_start;
  wire [25:0] ring1_trim_a;
  wire [2:0] ring1_clkmux;

digitalcore_macro digitalcore (
`ifdef USE_POWER_PINS
  .vccd1(vccd1),  // User area 1 1.8V power
  .vssd1(vssd1),  // User area 1 digital ground
`endif

  .wb_clk_i(wb_clk_i),
  .wb_rst_i(wb_rst_i),

  // MGMT SoC Wishbone Slave
  .wbs_cyc_i(wbs_cyc_i),
  .wbs_stb_i(wbs_stb_i),
  .wbs_we_i(wbs_we_i),
  .wbs_sel_i(wbs_sel_i),
  .wbs_adr_i(wbs_adr_i),
  .wbs_dat_i(wbs_dat_i),
  .wbs_ack_o(wbs_ack_o),
  .wbs_dat_o(wbs_dat_o),

  // Logic Analyzer
  .la_data_in(la_data_in),
  .la_data_out(la_data_out),
  .la_oenb (la_oenb),

  // IO Pads
  .io_in (io_in),
  .io_out(io_out),
  .io_oeb(io_oeb),

  // IRQ
  .irq(user_irq),

  // ring0 collapsering macro
  .ring0_clk(ring0_clk),
  .ring0_start(ring0_start),
  .ring0_trim_a(ring0_trim_a),
  .ring0_trim_b(ring0_trim_b),
  .ring0_clkmux(ring0_clkmux),

  // ring1 ringosc macro
  .ring1_clk(ring1_clk),
  .ring1_start(ring1_start),
  .ring1_trim_a(ring1_trim_a),
  .ring1_clkmux(ring1_clkmux)
);

collapsering_macro ring0 (
`ifdef USE_POWER_PINS
  .vccd1(vccd1),  // User area 1 1.8V power
  .vssd1(vssd1),  // User area 1 digital ground
`endif

  .clk_out(ring0_clk),
  .start(ring0_start),
  .trim_a(ring0_trim_a),
  .trim_b(ring0_trim_b),
  .clkmux(ring0_clkmux)
);

ringosc_macro ring1 (
`ifdef USE_POWER_PINS
  .vccd1(vccd1),  // User area 1 1.8V power
  .vssd1(vssd1),  // User area 1 digital ground
`endif

  .clk_out(ring1_clk),
  .start(ring1_start),
  .trim_a(ring1_trim_a),
  .clkmux(ring1_clkmux)
);

endmodule	// user_project_wrapper

`default_nettype wire