// SPDX-FileCopyrightText: 2020 Efabless Corporation
//
// Licensed under the Apache License, Version 2.0 (the "License");
// you may not use this file except in compliance with the License.
// You may obtain a copy of the License at
//
//      http://www.apache.org/licenses/LICENSE-2.0
//
// Unless required by applicable law or agreed to in writing, software
// distributed under the License is distributed on an "AS IS" BASIS,
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
// See the License for the specific language governing permissions and
// limitations under the License.
// SPDX-License-Identifier: Apache-2.0

`default_nettype none
/*
 *-------------------------------------------------------------
 *
 * user_project_wrapper
 *
 * This wrapper enumerates all of the pins available to the
 * user for the user project.
 *
 * An example user project is provided in this wrapper.  The
 * example should be removed and replaced with the actual
 * user project.
 *
 *-------------------------------------------------------------
 */

module user_project_wrapper #(
    parameter BITS = 32
) (
`ifdef USE_POWER_PINS
    inout vdda1,	// User area 1 3.3V supply
    inout vdda2,	// User area 2 3.3V supply
    inout vssa1,	// User area 1 analog ground
    inout vssa2,	// User area 2 analog ground
    inout vccd1,	// User area 1 1.8V supply
    inout vccd2,	// User area 2 1.8v supply
    inout vssd1,	// User area 1 digital ground
    inout vssd2,	// User area 2 digital ground
`endif

    // Wishbone Slave ports (WB MI A)
    input wb_clk_i,
    input wb_rst_i,
    input wbs_stb_i,
    input wbs_cyc_i,
    input wbs_we_i,
    input [3:0] wbs_sel_i,
    input [31:0] wbs_dat_i,
    input [31:0] wbs_adr_i,
    output wbs_ack_o,
    output [31:0] wbs_dat_o,

    // Logic Analyzer Signals
    input  [127:0] la_data_in,
    output [127:0] la_data_out,
    input  [127:0] la_oenb,

    // IOs
    input  [`MPRJ_IO_PADS-1:0] io_in,
    output [`MPRJ_IO_PADS-1:0] io_out,
    output [`MPRJ_IO_PADS-1:0] io_oeb,

    // Analog (direct connection to GPIO pad---use with caution)
    // Note that analog I/O is not available on the 7 lowest-numbered
    // GPIO pads, and so the analog_io indexing is offset from the
    // GPIO indexing by 7 (also upper 2 GPIOs do not have analog_io).
    inout [`MPRJ_IO_PADS-10:0] analog_io,

    // Independent clock (on independent integer divider)
    input   user_clock2,

    // User maskable interrupt signals
    output [2:0] user_irq
);

/*--------------------------------------*/
/* User project is instantiated  here   */
/*--------------------------------------*/

// Signals connecting OpenRAM with its wrapper
wire openram_clk0;
wire openram_csb0;
wire openram_web0;
wire [3:0] openram_wmask0;
wire [7:0] openram_addr0;
wire [31:0] openram_din0;
wire [31:0] openram_dout0;

// Signals connecting OpenRAM wrapper to Bus MUX
wire wbs_or_stb;
wire wbs_or_cyc;
wire wbs_or_we;
wire [3:0] wbs_or_sel;
wire [31:0] wbs_or_dat_i;
wire wbs_or_ack;
wire [31:0] wbs_or_dat_o;


sky130_sram_1kbyte_1rw1r_32x256_8 openram_1kB
(
`ifdef USE_POWER_PINS
    .vccd1 (vccd1),
    .vssd1 (vssd1),
`endif

    .clk0 (openram_clk0),
    .csb0 (openram_csb0),
    .web0 (openram_web0),
    .wmask0 (openram_wmask0),
    .addr0 (openram_addr0),
    .din0 (openram_din0),
    .dout0 (openram_dout0)
);

wb_openram_wrapper wb_openram_wrapper
(
`ifdef USE_POWER_PINS
    .vccd1 (vccd1),	    // User area 1 1.8V supply
    .vssd1 (vssd1),	    // User area 1 digital ground
`endif

    // Wishbone port A
    .wb_clk_i       (wb_clk_i),
    .wb_rst_i       (wb_rst_i),
    .wbs_stb_i      (wbs_or_stb),
    .wbs_cyc_i      (wbs_or_cyc),
    .wbs_we_i       (wbs_or_we),
    .wbs_sel_i      (wbs_or_sel),
    .wbs_dat_i      (wbs_or_dat_o),
    .wbs_adr_i      (wbs_adr_i),
    .wbs_ack_o      (wbs_or_ack),
    .wbs_dat_o      (wbs_or_dat_i),

    // OpenRAM interface
    // Port 0: RW
    .ram_clk0       (openram_clk0),         // clock
    .ram_csb0       (openram_csb0),         // active low chip select
    .ram_web0       (openram_web0),         // active low write control
    .ram_wmask0     (openram_wmask0),       // write mask
    .ram_addr0      (openram_addr0),
    .ram_din0       (openram_dout0),
    .ram_dout0      (openram_din0)
);

wb_ram_bus_mux wb_bus_mux
(
`ifdef USE_POWER_PINS
    .vccd1 (vccd1),	    // User area 1 1.8V supply
    .vssd1 (vssd1),	    // User area 1 digital ground
`endif

    // Wishbone UFP (Upward Facing Port)
    .wb_clk_i        (wb_clk_i),
    .wb_rst_i        (wb_rst_i),
    .wbs_ufp_stb_i   (wbs_stb_i),
    .wbs_ufp_cyc_i   (wbs_cyc_i),
    .wbs_ufp_we_i    (wbs_we_i),
    .wbs_ufp_sel_i   (wbs_sel_i),
    .wbs_ufp_dat_i   (wbs_dat_i),
    .wbs_ufp_adr_i   (wbs_adr_i),
    .wbs_ufp_ack_o   (wbs_ack_o), 
    .wbs_ufp_dat_o   (wbs_dat_o),
/*
    // Wishbone HR (Downward Facing Port) - HyperRAM driver
    output          wbs_hr_stb_o,
    output          wbs_hr_cyc_o,
    output          wbs_hr_we_o,
    output  [3:0]   wbs_hr_sel_o,
    input   [31:0]  wbs_hr_dat_i,
    input           wbs_hr_ack_i,
    output  [31:0]  wbs_hr_dat_o,
*/

    // Wishbone OR (Downward Facing Port) - OpenRAM
    .wbs_or_stb_o    (wbs_or_stb),
    .wbs_or_cyc_o    (wbs_or_cyc),
    .wbs_or_we_o     (wbs_or_we),
    .wbs_or_sel_o    (wbs_or_sel),
    .wbs_or_dat_i    (wbs_or_dat_i),
    .wbs_or_ack_i    (wbs_or_ack),
    .wbs_or_dat_o    (wbs_or_dat_o)
);

endmodule	// user_project_wrapper

`default_nettype wire